Help with regards to customize settings

Dear sir i am unable to print on customize settings after 3 times printing,the issue is that when i customize my settings i will get print 3 times on my given setting but after that the printer comes to default settings and print a single page and with default configured darkness,The whole issue is regard with copier.Provide me assistance as soon as possible.Thanks to someone who is concerned.

,Welcome to the Forums! I saw your post about the troubles you're having with setting custom sizes and having them stay permanently in your settings. I will do my best to help you. Please start with telling me what exact custom sizes, or settings you are selecting to use, and which program you are using. Also try Uninstalling the Printer Software, restarting your PC, and then reinstall the printer by running the HP Printer Install Wizard for Windows. Try your custom sizes again! Please check the specifications sheet for your LaserJet M126nw to make sure you are using supported sizes for this model: HP LaserJet Pro MFP M125 and M126 Printer Series Product Specifications Good luck

Similar Messages

Need help with the noise reduction settings

Hi,
After som experimenting I need some help with the settings for noise reduction.
I just edited and converted a few pictures from RAW (D200) til 8-bit TIFF. Opend the file up in photoshop and was shocked to see the amount of noise in the pictures. I then exported the RAW-files and did the same conversion in Capture One 3.7.3 - The result is a lot better regarding noise. In capture One I'm using the noise reduction step before "High".
Can you share your experience with the optimal settings for best noise removal ?
Thanks in advance,
fbrose

i use it once in a while, but i play around with the sliders in full screen mode and at 100% and then see what the sliders do. I don't have a definite procedure that I can suggest though.

Please help with highest quality export settings...

I have searched the forum and web for hours (no joke!) and I am still trying to figure out what are the best video settings to give me the highest HD quality video in daylight. I am using a Canon HF200 and the latest updated version of FCE. My problem is that I am unable to produce an HD quality video at 1920 x 1080 Full HD without being "jagged". I have two questions; what do you suggest to be the best FCE import and export settings to produce the best HD video, and what settings do you have your HF200 set to (for normal daylight conditions), to produce the best HD video file? The file will be played directly thru my computer to a plasma HDTV.
I have tried several settings, but using anything above 1280x720 16:9, makes the video "jagged". Again, I don't care about the size of the file or how long it takes, I just want the best. Is there something I am missing?
My FCP settings are the following:
I log and transfer the video from the camera into FCP (on a black MacBook; 2.16 GHz with 4 GB RAM) using the AVCHD Apple Intermediate Codec 1920 x 1080i source. I then export the video using the following:
Export using "Quicktime Conversion".
Quicktime options video settings are:
Frame Rate set to "Current"
Key Frames set to every "24" frames
Compressor quality: "best" (Encoding set to "best quality")
Data Rate set to "automatic"
Quicktime options video size are:
"HD 1280 x 720 16:9" (anything higher produces the jags!)
Deinterlace source video is NOT checked
My Canon HF 200 settings are the following:
- P mode
- FXP (17 Mbps)
- 60i framerate
all others are set to the normal default
I have read some reports saying the above is good and others suggesting changing FXP to MXP (24 Mbps) and/or the framerate from 60i to PF30. I don't care about the size of the file, I just want the highest quality HD file.
Any suggestions for the best FCE settings and/or HF200 settings would be very much appreciated!
Thanks for your help,
Evan

Thanks again for the feedback
Let me try my best to answer the above (I'm new at all this and I appreciate you guys taking the time to try and help me out).
First off, I tried rendering and that did not help.
Here is my sequence. I am not going into FCE from the camera directly. I have archived the video file from the camera using iMovie (as well as just making an exact copy of the camera files; they both appear to me to be the exact same, both can be logged and transferred into FCE, and both files give me a jagged FCE result).
Once I log and transfer the file(s), I then take the clip and add it to a sequence file (rendering or not rendering the clip(s) at this point does not make a difference), and then click/highlight the sequence file in the browser and export it.
As for "editing the video in a 1920x1080i60 sequence", I think I am. I am not doing any editing to the clip. It is logged and transferred using the AVCHD Apple Intermediate Codec 1920 x 1080i and then exported using either as a Quicktime Movie or Quicktime Conversion (set for 1920 x 1080 using H.264 compression; both ways still result in a jagged video).
That's about it...log and transfer, add clip to sequence, and then export sequence...
I hope this answers the above, but if not, I apologize; I'm still learning!
Also, if I use iMovie, with similar export (share) settings, I get a non-jagged video (I have tried with deinterlacing and not deinterlacing, and both video results are fine)
Thanks again,
Evan

Help with Gateway TG799 Firewall settings Please

We have a Telstra Gateway Max TG799vac.
We have recently acquired our own domain name and have setup up an online store on Shopify.
So the underlying web address (on myshopify.com) is not the same as our URL of the shop.When we try to access the new site from any computer or device from within our house
we are blocked 90% of the time. It occasionally will connect. We are therefore unable to do admin on our own site.
I have tried USB tethering thru my phone's data and works 100% no worries. This bypasses the gateway and Telstra of course.
Anyone outside our home can always connect no worries.I have suspected the Firewall in the gateway TG799 device.
So I went into settings and changed the firewall setting down to the LOW setting.
Then we can connect all the time.
When in NORMAL or HIGH then we get this intermittent (mostly failed) connection.
After this experiment I am convinced it has something to do with the internal firewall.There is also a USER DEFINED section where you can set your own firewall rules
but I don't know enuff about what to do in there to experiment.
But I think I could set up a rule in there to allow this site to work for us if I knew how to go about it.I have been unable to find anyone within the normal Telstra tech help line who can help with this.Does anyone on here have any such knowledge or can give me a pointer where I can read/learn about how to do this for myself.Any help will be greatly appreciated.

Thanks Steph,The fact that these devices are updated by Telstra remotely without our prior knowledge explains alot.It explains why the problem I first reported just started to happen out of the blue.It also explains why it just as mysteriously disappeared. It also explains why we suddenly had trouble with our phones dropping the wifi connection constantly.And why that suddenly fixed itself as well. It also explains why we suddenly got a monstrous over-use on our data bill on our Telstra mobile.We thought we were safe in our own house to use data on this phone knowing it was connected to our wifi and therfore our BigPond plan. What we did not know was that the phone was loosing sync with the wifi and therefore dropping back to 3G plan data use without our knowledge. My wife had been using her phone to connect to a Chinese movie streaming site and of course when the wifi dropped out she did not know she was streaming thru her 3G plan. Massive unexplained data over-use resulted. I had a rough time convincing your billing organisation that we were using wifi (or thought we were anyway) for the movies and they would not believe us therefore the monster bills were upheld. We did not reaslise until far too late that the phone was loosing the wifi connection without us knowing. We have stopped using that service now and as soon as the credit we accumulated with the associated billing stuff-ups is used up we will be leaving Telstra for another less troublesome provider. How about giving us poor defenseless users some notice that our devices have been updated and a summary of what aspects have been changed. Just like happens with apps on the Google Play store. I will now be approaching your billing organisation once more armed with this knowledge. My argument will be that our over-use on 3G data stemmed from a bad firmware update without our knowledge in your modem causing us to over-use 3G data we were not aware of. This time if they don't listen then it will be time for a complaint to the TIO. And perhaps even a media story. Disgusting service! And one angry Telstra customer.

Help with most practical format/settings please!

Hi Everyone out there!
I'd really appreciate some spelled-out advice as I have only ever used FCP with a DV Pal camera for high end stuff and thus also known how to set a sequence up and capture stuff but only for that format!
Right!
I have been supplied a batch of 40 small video clips taken from a photo camera. They were MPEG 1 muxed, and I have demuxed them with Mpeg streamclip.
They are:
Video: 224 Mpeg 1, 640x480, 30fps, 8Mbps
Audio: 160 Pcm stereo, 32khz, 1.02Mpbs
I have been asked to edit a little promo film out of them and then export it suitable for uploading to facebook / use on the web. I can't seem to find out what settings are optimum for facebook uploading seeing as I want to retain as much quality as possible given the initial format supplied in!
Any help advice would be appreciated. Basically I'm trying to work out exactly what setup the project/sequence should be in. Easy setup doesn't seem to make much sense and I've tried a few settings but each time I start putting clips in the sequence they have to be rendered before playing which makes making this thing a nightmare!
Thanks
Hannah
Message was edited by: Hannah Madsen

I'd save them out as DV .mov's Edit in a dv easy set up. From there you can compress into whatever it is that facebook likes. Sorry, I've no idea about that. Never even visited it.

Help with Iprocurement jdeveloper customization

Hi
I am trying to customize the iprocurement check out summary jsp page.
I am new to jdeveloper and have no previous experience in that.
I needed to know , waht B4J directory to download and where to locate it on the server.
I basically have to re initiate the account generator when the user changes the deliver to location field on the check out page.
i think this is name of the pages:
checkoutsummary.xml
checkoutsummaryco.class
this is what I have right now.
any help or direction will be appreciated.
thanks

As you are saying that you are new to jdeveloper and have no previous experience .
So Better to take some experience with OAF , DownLoad Jdeveloper try to do initial exerciese that come with OAF Installer that push you towards more depth in OAF.
Come back with any issue you have .
Thanks, Avaneesh

Help With LightRoom Aspect Ratio Settings

I have created some custom Aspect Ratio settings to the crop tool but I now want to delete them as I entered them wrong.
Can anyone tel me how I can delete the custom ones I have made or reset back to defaults.
I am guessing they are written out to a file somewhere.
Ian

Hi
Many thanks for all your help. (very useful information)
This is now fixed and although it did not affect the useage, it did bother me
Regards
Ian

I need help with some technical YouTube Settings, third party tools page

How can I add ios mobile Safari, back to my google + third-party tools page? I updated my ipad 2 to ios7 and could no longer upload videos to youtube for my blog. YouTube had been saying unrecognized file type because it's not longer compatible with ios mobile photos app.
I went into settings via the google/youtube help files and removed some old stuff from the third party apps, like blogger-an inactive blog and obviously deleted the ios moblie too that was right underneath blogger. tried jumping through their hoops, add a phone number, verify your account, lengthen your video time, add 2 step verification (which was horrible and I went back in and removed it), add a password for ipad, etc.
They (youtube/google??) have been working on stuff because there is all kinds of new things the second day I tried to figure this out via their help/redirect links. ios mobile was there before and now it's gone, even though I did not choose/select it. But I have noticed that the ipad screen is much more sensitive than it was before the ios7 update. I don't even have to touch the screen for some things, it accepts and goes on it's own while my finger is hovering over the screen.
ipad2
ios7.0.2
Safari
YouTube
Google+

The Title of my post, should really be....I have ipad2 with ios7.0.3 and Safari, I can't upload videos to YouTube because of Google? or ios7?
It's now November 1st. LOL 53 folks have read my problem and it only gets better. I pleaded with Google/YouTube via Feedback form (because they are one and the same now) to please add ios mobile back to Google 3rd party apps and after checking every single day, someone finally added it back for me. Yay! Then I asked if I needed to "revoke" Google+ in the 3rd party apps because some of the help files suggested Google+ is attached to your YouTube channel and might affect uploading of videos? For the life of me, I could not figure out how to get it off my YouTube channel. And the help files didn't take me to a place to change it. Upon checking 3rd party apps, I could no longer find the page they were on, and the Google+ app icon now goes no where.
Hey, but there are new menus with all kinds of statistics now about your account, like how many subscribers you have, what the average number of minutes people watch your videos,etc. Hmm... so I tried uploading a video and it worked. I got the message that ios7.0.3 with bug fixes was available a few days ago and updated to that. I'm back to, no longer upload videos, yesterday it was still freezing on the upload screen, where you add the title of your video and all of the specs, it appears to be half uploaded with a solid blue bar half way and goes no where. I have to close the app after an hour or more. I have rebooted a couple of times every day. Today it says, we could not upload your video, we did not recognize the format of this file. And when I go to YouTube and can see all of my videos, my subscriptions, I can not remove the videos that tried to upload, they are blank gray squares. A few days ago I could edit them out. I guess they are still working on it. These are the same self recorded videos, that I have been uploading for a year, same ipad. I have sent feedback to Google/YouTube once again.
I'm completely at their mercy. I have yahoo mail, so I can't send my videos via email, even though my channel has a special email address to send videos to for upload. Yahoo will not send a video more than a minute or so. I created an AT&T email address today, and it's the same there, will not send a 15 minute video. The upload link on YouTube no longer works, there on the same page with your special email address to mail your videos in, even though there is no email that supports a 15 minute video. My husband suggested video compressing program. I have not tried to upload from a PC, I do have icloud, so that may be my next route. Other forums say they/Google/YouTube are fully aware of it and are working on it. Still 30+ days in...
It's a shame these companies can't work together, it's a shame that there is no answer, because we all have these devices we spent hundreds of dollars on and want them to work. I have been searching the web for 30+ days and no one knows the answer. Hard to believe I'm the only person having this ipad issue.

Immediate help with regards to grouping and decoding

Hi all
I have got a problem recently where I was asked whether this can be done using a single SQL statement.
The table data is from a flat file like this.
SITE TOOL PROD TOOLPROD
ABC DEN_01 15 DEN_01
ABC DEN_01 15 DEN_01|01
ABC DEN_01 15 DEN_01|02
ABC DEN_01 15 DEN_01|03
DEF DE_03 17 DE_03
DEF DE_03 17 DE_03|07
DEF DE_03 17 DE_03|08
and the sumarized result set should look like this from above info i.e grouped by site,tool,prod columns and the last columns toolprod concatenated as shown below. There is lot of data like this and hardcoding cannot be done since there are millions of rows like this.
ABC DEN_01 15 DEN_01|DEN_01|01|DEN_01|02|DEN_01|03
DEF DE_03 17 DE_03|DE_03|07|DE_03|08
Appreciate your help
Thanx in advance
Kris

Sys_connect_by_path is a 9i feature that provides the path from the root to the node in a hierarchical query. For an 8i workaround you can use the folloing hiearchy package by Solomon Yakobson. I know the package works in 8i, because that is what it was designed for and I used it in 8i, but I do not know if it will work in conjunction with the rest of the code, as I do not have 8i to test with anymore, and there were some restrictions as to what you could do with hierarchical queries in 8i. You may have to add some additional nesting of inline views or some such thing.
scott@ORA92> -- hierarchy package with branch function by Solomon Yacobson
scott@ORA92> CREATE OR REPLACE
2   PACKAGE Hierarchy
3    IS
4           TYPE BranchTableType IS TABLE OF VARCHAR2(4000)
5             INDEX BY BINARY_INTEGER;
6           BranchTable BranchTableType;
7           FUNCTION Branch(vLevel          IN NUMBER,
8                     vValue          IN VARCHAR2,
9                     vDelimiter      IN VARCHAR2 DEFAULT CHR(0))
10                     RETURN VARCHAR2;
11           PRAGMA RESTRICT_REFERENCES(Branch,WNDS);
12 END Hierarchy;
13 /
Package created.
scott@ORA92> CREATE OR REPLACE
2   PACKAGE BODY Hierarchy
3    IS
4           ReturnValue VARCHAR2(4000);
5    FUNCTION Branch(vLevel          IN NUMBER,
6                  vValue          IN VARCHAR2,
7                  vDelimiter    IN VARCHAR2 DEFAULT CHR(0))
8                  RETURN VARCHAR2
9      IS
10      BEGIN
11           BranchTable(vLevel) := vValue;
12           ReturnValue := vValue;
13           FOR I IN REVERSE 1..vLevel - 1 LOOP
14             ReturnValue := BranchTable(I)|| vDelimiter || ReturnValue;
15           END LOOP;
16           RETURN ReturnValue;
17    END Branch;
18 END Hierarchy;
19 /
Package body created.
scott@ORA92> select site, tool, prod,
2          replace (max (hierarchy.branch (level, toolprod)), ',', '|')
3            as toolprods
4 from   (select site, tool, prod, toolprod,
5               row_number () over
6                 (partition by site, tool, prod
7                  order by toolprod) as curr,
8               row_number () over
9                 (partition by site, tool, prod
10                  order by toolprod) - 1 as prev
11           from   your_table)
12 group by site, tool, prod
13 start with curr = 1
14 connect by prior curr = prev
15           and prior site = site
16           and prior tool = tool
17           and prior prod = prod
18 /
SITE TOOL         PROD TOOLPRODS
ABC DEN_01         15 DEN_01 DEN_01|01 DEN_01|02 DEN_01|03
DEF DE_03          17 DEN_03 DEN_03|07 DEN_03|08The second solution that I provided, using Tom Kyte's stragg user-defined aggregate function also requires 9i. The third solution with a function specific to the situation should work in 8i though. The following is an addiitional generic option for 8i.
scott@ORA92> CREATE OR REPLACE FUNCTION concatenate
2    (p_key_name      IN VARCHAR2,
3      p_key_value      IN VARCHAR2,
4      p_col_to_concat IN VARCHAR2,
5      p_table_name      IN VARCHAR2,
6      p_separator      IN VARCHAR2 DEFAULT '|')
7    RETURN              VARCHAR2
8 AS
9    TYPE weak_ref_cur IS REF CURSOR;
10    v_string          VARCHAR2 (4000);
11    v_separator         VARCHAR2 (      3) := NULL;
12    v_value              VARCHAR2 (4000);
13    v_cur              weak_ref_cur;
14 BEGIN
15    OPEN v_cur FOR
16         'SELECT ' || p_col_to_concat
17    || ' FROM '   || p_table_name
18    || ' WHERE ' || p_key_name || ' = :b_key_name'
19    || ' ORDER BY :b_col_to_concat'
20    USING p_key_value, p_col_to_concat;
21    LOOP
22       FETCH v_cur INTO v_value;
23       EXIT WHEN v_cur%NOTFOUND;
24         v_string := v_string || v_separator || v_value;
25         v_separator := p_separator;
26    END LOOP;
27    CLOSE v_cur;
28    RETURN v_string;
29 END concatenate;
30 /
Function created.
scott@ORA92> select site, tool, prod,
2          concatenate ('site || tool || prod',
3                 site || tool || prod,
4                 'toolprod', 'your_table') toolprods
5 from your_table
6 group by site, tool, prod
7 /
SITE TOOL         PROD TOOLPRODS
ABC DEN_01         15 DEN_01|DEN_01|01|DEN_01|02|DEN_01|03
DEF DE_03          17 DEN_03|DEN_03|07|DEN_03|08
scott@ORA92>

Need help with itunes / iphone sync settings

The old computer I synced my iphone to is no longer working and i never changed my music settings to "manual". Is there a way to change it on my phone to where I don't lose all of my songs? Or is there a way of backing up my songs from my phone to a flashdrive or other sources? Please help!

The option will be in your third party tool.
tt2

Help with sequence and export settings

hi
need to edit some clips made with camtasia using the tech smith codec
first i convert clips to dvd using stoki converter
then when i start prem cs4 i not sure which settings to use in the "new sequence" window under the editing mode drop down
also not sure of the settings at export settings under the format drop down
need to maintain the best quality
thanks

For the answer to "what Sequence Preset?" you will want to match your Imported footage 100%, even if that means choosing the Desktop Preset, and then customizing all aspects of it, to match.
For the Export, start with "how do I intend to deliver this material?" That will give you the basic settings, and then you can tweak those to suit. How do you plan to deliver the material?
Good luck,
Hunt
PS - this ARTICLE might prove useful.

Help with 24p capture/sequence settings and interlace artifacts

We are trying to capture sd video shot on a panasonic DVX 100B at 24p (not advanced) using FCP 6.02.
The video was shot anamorphic (squeeze) through the camera.
We have tried a variety of capture and sequence setting and continue to get varying degrees of artifact (lines) at motion points (e.g. when a hand moves).
We have tried:
Capture Easy set-up 29.97
Capture Anamorphic 29.97
We have tried changing field dominance to none.
We have experimented with both interlace and progressive scan.
We have experimented with different playback units including the camera shot with.
Would love some advice on best capture sequence settings. Playback will be computer/video projector.

It's sounds like you've been mislead about what 24p (as opposed to 24p Advanced) actually is on tape - it's interlaced 29.97 footage. So, what you're seeing is normal - there should be three progressive frames followed by 2 interlaced frames (since it's pulldown added to 23.98 material).
So, to get to the heart of your question, you are capturing correctly - Anamorphic 29.97.
If you want true progressive output, strip the pulldown - use Cinema Tools - and edit as 23.98. Otherwise, if you can't go 23.98, you're stuck with what you've got.

HT201365 Help with Find My iPhone Settings

In my: Settings-iCloud-Find My iPhone, The icon "Find My iPhone" and green button slide are all muted and will not allow me change it, yet on my iPad next to last generation with iOS 7.1 all of the above are bright in color. Help

Check Settings>Privacy>Location Services to make sure it's turned on, then scroll down and tap Find My iPhone and turn it on.

Help with Preference pane DNS settings for Mail

I have a mail (not Apple Mail) issue with my Entourage Mail. I keep getting
the following error message and I have verified the server settings in my
mail accounts are correct for ATT that uses pop.att.yahoo.com. I manage to
get mail most of the time but I still get the following error message:
Error Description
Error:
Entourage cannot find the server. Verify the server information is entered correctly in the Account Settings, and that your DNS settings in the Network pane of System Preferences are correct.
Explanation:
Could not retrieve mail
Error: -1370
My System Preferences/Network/Advanced/DNS point to my 2wire Gateway combo
modem/router. The router is set for Automatic DNS. I tried changing it to manual
and it did not works any better.
If I change the DNS setting in the preference pane in OS X, will it really use that
DMS address and bypass the router?
I played around with the namebench utility
http://www.macupdate.com/info.php/id/32784/namebench and each time you
run it, namebench makes a better recommendation - saying something is faster
than the previous recommendation.
I am lost on what I need to do correct the Network pane of my System Preferences.
Should it point to the router or to good DNS?
I do not think this is a Microsoft Entourage issue.
Have others seen this issue or is unique to my setup.

Going to sleep on and see how it works in the morning.
The problem is solved and I have checked the Yes button that my
question has been answered. The following is a copy of a posting
two days ago to the Microsoft Entourage group that should work
just as well for Mail users.
If you are tied of getting the following Entourage error
message -3170 over and over again, read on.
Error:
Entourage cannot find the server. Verify the server information
entered correctly in the Account Settings, and that your DNS
settings in the Network pane of System Preferences are correct.
Explanation:
Could not retrieve mail
Error –3170
Thanks to a tip from Diane Ross I have gone two days without
getting the error message.
First, I know the Account Settings for my ATT DSL service
have been correct for some time and have not changed.
The short version of the fix that worked for was to open
the OS X 10.6.3 (Snow Leopard) System Preferences/
Network/Advanced/DNS panel and add some better Domain
Name Servers from my location.
The default (or before) OS X setting was:
DNS Servers: Search Domains:
192.168.1.254 gateway.2wire.com
Note both were dimmed. The server listed tells OS X to use
the ATT provided combo 2wire modem/router for my DSL service.
The change that seem to have worked for me was to leave the
Search Domain the same; however, I added some good servers that
bypass the 2wire gateway with its automatic DNS setting.
DNS Servers: Search Domains:
208.67.220.220 gateway.2wire.com
208.67.220.222
65.68.49.51
192.168.1.254
I found the ‘good’ or better DNS Servers by making several runs
using the free Google utility called namebench 1.2
<http://www.macupdate.com/info.php/id/32784/namebench>
This utility takes some time and will make suggestions from your
location. If you add the namebench recommendation and run it
again it will find a better recommendation. I had to make several
runs to find the better DNS Servers for my location. The first or
primary is called OpenDNS, the second is a backup for the OpenDNS
and the third is SBC Global TX now owned by ATT and I live in
Texas. Note I ended with the default IP address.
FYI, I tied using the selected servers in the 2wire gateway in the
manual mode rather than the default automatic mode and it just
did not work right. Some pages would not open and others were
slow. For this reason I run the router in the automatic mode for
DNS and control things using the OS X Network preference pane.
The addition of preferred DNS Servers in my Preference seems
to have slowed down and hopefully stopped Entourage 2008
version 12.2.4 -3170 error messages.
Message was edited by: aRKay

Some help with Bitlocker related GPO settings

I don't understand all of these settings. We have a following policy configured related to Bitlocker. Configure TPM Startup: Do not allow TPM. What does this really mean? I don't understand why it is not configured as "Allow TPM".

See this TechNet article for a description of each key.
The setting for Configure TPM Startup configures whether the operating system driver can be protected with the TPM only (not TPM+PIN, TPM+Key, or TPM+Key+PIN).
Brandon
MDOP for IT Professionals on TechNet

Help with regards to customize settings

Similar Messages

Maybe you are looking for