Help with setting up Caller-id on FXO in 2911 H.323 gateway.

I have a remote site that has a couple of POTS lines terminating to a FXO on the 2911. This remote site is an H.323 gateway in a CUCM 8.6 cluster. Incoming local calls for that location ring all phones at the location.
What do I need to do to enable Caller-id on these POTS lines terminating to the FXO? I am pretty sure the carrier is sending the caller ID information.
Thanks

Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID
Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
2- under fxo port
voice-port 0/3/0
caller-id enable
3-If the above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ? "based on your"
caller-id alerting ring 2 "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debus to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information

Similar Messages

Can anyone help with setting up AirPrint on my iPhone 4

Can anyone help with setting up AirPrint on my iPhone 4. Printer is ready.

you have a compatable printer correct? http://support.apple.com/kb/ht4356
if you do may i introduce you to a hassel free app for your mac called printopia i use it also very easy to set up and use
http://www.udeo.com/mac/printopia/
hope thats helped
Goody

Help with multiple httpservice calls

I need help with multiple httpservice call back to back, doing 10 different mysql query at startup of the app loading results into 14 datagrids/combobox all queries are to different tables.

Hello,
I think what Grizzzzzzzzzz means is the following:
 <mx:HTTPService id="serviceOne"
 url="here goes url"
 result="resultHandler1(event);"
 fault="faultHandler(event);"/>
 <mx:HTTPService id="serviceTwo"
 url="here goes url"
 result="resultHandler2(event);"
 fault="faultHandler(event);"/>
 <mx:HTTPService id="serviceThree"
 url="here goes url"
 result="resultHandler3(event);"
 fault="faultHandler(event);"/>
 // Result handler 1
 private function resultHandler1(event:ResultEvent):void{
 //Here do something with the results
 xmlCollection = event.result as XML;
 //then call the next service
 serviceTwo.send();
 // Result handler 2
 private function resultHandler2(event:ResultEvent):void{
 //Here do something with the results
 xmlCollection = event.result as XML;
 //then call the next service
 serviceThree.send();
I hope this helps,
Pierre

Purchased extreme to replace modem/router DSL used telephone cord need help with set up

Prior to purchasing Airport Extreme had a standard modem/ wireless router from ATT for DSL. I have two macbooks both dropped connections while online with older modem.
Airport Extreme purchased to correct connection issues I need help with set up. The older modem just used telephone cord. I tried to use telephone with extreme it did not work.
How do I get extreme to work as the modem and router ?

How do I get extreme to work as the modem and router ?
you can't. the extreme is only a router. you need a separate modem (or disable the wireless part of your old router and use it as a modem - if that's possible).

I need help with setting up time machine for backup

I would like help with setting up time machine for backup.

You will need an external hard drive (formatted for a Mac).
Then you plug it in and go to system preferences>time machine and select the external HD and turn it on.
The backups are automatic.
Barry

I need help with setting up my Sun Java Studio Creator

Hello all, i need help with setting up the Studio Creator, i"m new to all that staff so is there anyone to help me just a little with all that if yes email me at [email protected] or get me on AOL Instant Messanger with the screen name: wretch17
thanks :-)

Hi,
Welcome to the Creator community! Thanks for your interst in Sun Java Studio Creator. Please feel free to post any question related to creator on this forum .
Take a look the creator website at
http://developers.sun.com/prodtech/javatools/jscreator/
CreatorTeam

Help with Refreshing and Calling Screens

Hi everyone. I have somewhat of a simple ABAP program in which the user will enter data on Selection-Screen 1000. This will then be loaded into an Object Oriented ALV Grid for display purposes only (screen 0100). At any time, the user may use the back button on the ALV Grid Screen; which will take them from screen 0100 to screen 1000(Selection Screen). Lets assume the user does not want to go back to the original selection screen from the ALV Grid Screen; they entered the information correctly and want to continue processing using a custom button I've created which will continue to process the record of data into a BW ODS. This process works, but now I would like to use the write statement once the custom button is clicked to show a summary of the data I am inserting into the ODS after the data has been inserted. The problem is, the title of the ALV Grid still shows and the Write statement is processed, but not shown on the screen. I've been trying to refresh the screen with set screen and call screen combinations, but no luck. Any Help would be appreciated. Thanks!
Here is a sample of the code below:
*& Report ZINC_DSP_SALES_INCRASE
REPORT ZINC_DSP_SALES_INCREASE MESSAGE-ID zsm.
INCLUDE <icon>.
DATA: credit_itab type standard table of /bic/azincosvi00,
 wa_credit like line of credit_itab,
 alv_itab type standard table of /bic/azincosvi00,
 wa_alv like line of alv_itab.
DATA: ok_code LIKE sy-ucomm,
 save_ok LIKE sy-ucomm,
 incent type table of /bic/azincosvi00,
 g_container TYPE scrfname VALUE 'Increase DSP Sales',
 grid1 TYPE REF TO cl_gui_alv_grid,
 gs_layout TYPE lvc_s_layo,
 g_custom_container TYPE REF TO cl_gui_docking_container.
DATA: active_guid like /bic/mzguid_dsr,
 UNIQUEKEY LIKE /BIC/AZINCOSVI00-/BIC/ZRCRDKEY,
 rpt_per_rec like /BIC/MZRPTPRDCR,
 dsrcode like /bic/mzdsrcode-/bic/zdsrcode,
 payrec like /bic/mzsubcode.
CLASS lcl_event_receiver DEFINITION DEFERRED.
CLASS lcl_event_receiver DEFINITION.
PUBLIC SECTION.
 METHODS:
 handle_toolbar
 FOR EVENT toolbar OF cl_gui_alv_grid
 IMPORTING e_object e_interactive,
 handle_user_command
 FOR EVENT user_command OF cl_gui_alv_grid
 IMPORTING e_ucomm.
 PRIVATE SECTION.
ENDCLASS.
CLASS lcl_event_receiver IMPLEMENTATION.
This will create the toolbar
METHOD handle_toolbar.
 DATA: ls_toolbar TYPE stb_button.
 CLEAR ls_toolbar.
 MOVE 3 TO ls_toolbar-butn_type.
 APPEND ls_toolbar TO e_object->mt_toolbar.
append an icon to show booking table
 CLEAR ls_toolbar.
 MOVE 'CREATE' TO ls_toolbar-function.
 MOVE ICON_OKAY TO ls_toolbar-icon.
 MOVE ' ' TO ls_toolbar-disabled.
 APPEND ls_toolbar TO e_object->mt_toolbar.
ENDMETHOD.
METHOD handle_user_command.
CASE e_ucomm.
WHEN 'CREATE'.
Insert /bic/azincosvi00 from wa_credit.
CALL METHOD grid1->free.
SET SCREEN '200'.
WHEN 'OTHERS'.
" DO NOTHING
ENDCASE.
ENDMETHOD.
ENDCLASS.
Data: event_receiver TYPE REF TO lcl_event_receiver.
START-OF-SELECTION.
Selection-Screen BEGIN OF BLOCK 1 with frame title text-001.
Parameters: start like /bic/azincosvi00-BILL_DATE.
Selection-Screen END OF BLOCK 1.
Selection-Screen BEGIN OF BLOCK 3 with frame title text-003.
Parameters: guid type /BIC/OIZGUID_DSR,
 pcode type /BIC/OIZPGMCODE,
 scode type /BIC/OIZSUBCODE,
 reason type /BIC/OIZEXCPTC,
 quantity(5) type n,
 discount type /BI0/OISUBTOTAL_4.
Selection-Screen END OF BLOCK 3.
END-OF-SELECTION.
IF quantity <> '00000'.
 if pcode <> 'SCTMS'.
 message e000 with 'Quantity can only be used with seating spiff'.
 endif.
ENDIF.
GET REPORT PERIOD INFO using today's date.
select single * from /bic/mzrptprdcr INTO rpt_per_rec
 where calyear = sy-datum(4)
 and /bic/zpgmcode = pcode
 and ( /BIC/ZRPPRDSTR <= start
 and /BIC/ZRPPRDEND >= start ) .
if sy-subrc <> 0.
 message e000 with
 'Report Period NOT FOUND for' pcode ' ' sy-datum(4).
endif.
Select Active Guid based upon user entry on selection-screen
Select single * from /bic/mzguid_dsr into active_guid
 where /bic/zguid_dsr = guid
 and /bic/zdsrstat = 'A'.
 If sy-subrc <> 0.
 MESSAGE e000 WITH 'Please enter a valid GUID'.
 ENDIF.
Select DSR Code based upon a valid guid entered
Select single /bic/zdsrcode from /bic/mzdsrcode into dsrcode
 where /BIC/ZGUID_DSR = guid
 and /BIC/ZDSRCDST = 'A'.
 If sy-subrc <> 0.
 MESSAGE e000 WITH 'GUID entered does not have an active dsr code.'.
 ENDIF.
Select MAX( /BIC/ZRCRDKEY ) FROM /BIC/AZINCOSVI00 INTO WA_CREDIT-/BIC/ZRCRDKEY.
UNIQUEKEY = WA_CREDIT-/BIC/ZRCRDKEY + 1.
WA_CREDIT-/BIC/ZRCRDKEY = UNIQUEKEY.
WA_CREDIT-PO_NUMBER = UNIQUEKEY.
WA_CREDIT-/BIC/ZERDAT = SY-DATUM.
WA_CREDIT-BILL_DATE = SY-DATUM.
WA_CREDIT-/BIC/ZRPPRDSTR = rpt_per_rec-/BIC/ZRPPRDSTR.
WA_CREDIT-/BIC/ZRPPRDEND = rpt_per_rec-/BIC/ZRPPRDEND.
WA_CREDIT-/BIC/ZCUBPRCDT = SY-DATUM.
WA_CREDIT-/BIC/ZRPTPRDCR = rpt_per_rec-/BIC/ZRPTPRDCR.
WA_CREDIT-/BIC/ZINCPYPRC = '00000000'.
WA_CREDIT-/BIC/ZGUID_DSR = ACTIVE_GUID-/bic/zguid_dsr.
WA_CREDIT-/BIC/ZDSRCODE = dsrcode.
WA_CREDIT-/BIC/ZPGMCODE = PCODE.
WA_CREDIT-/BIC/ZUNASSIGN = 'N'.
WA_CREDIT-/BIC/ZSUBCODE = SCODE.
WA_CREDIT-/BIC/ZSITE_ICR = ACTIVE_GUID-/BIC/ZSITE_IRG.
WA_CREDIT-/BIC/ZSUSPEND = 'N'.
WA_CREDIT-/BIC/ZSUSPNDR = ' '.
WA_CREDIT-/BIC/ZSITE_IRG = ACTIVE_GUID-/BIC/ZSITE_IRG.
WA_CREDIT-/BIC/ZSITE_CST = ' '.
WA_CREDIT-/BIC/ZINCBONUS = '0.00'.
WA_CREDIT-STAT_CURR = 'USD'.
WA_CREDIT-DOC_CURRCY = 'USD'.
WA_CREDIT-SALES_UNIT = 'ST'.
WA_CREDIT-CALYEAR = SY-DATUM(4).
WA_CREDIT-/bic/ZCASEID = SY-UNAME.
WA_CREDIT-/bic/ZSLSRSN = REASON.
WA_CREDIT-RECORDMODE = ' '.
*Depending on Program Code, populate the amounts to be paid.
Data: fivepercent type p.
 fivepercent = '0.05'.
If pcode = 'SCW5S' or pcode = 'SCTMS'.
Select single * from /bic/mzsubcode into payrec
 where /bic/zpgmcode = pcode
 and /bic/zsubcode = scode
 and CALYEAR = sy-datum(4).
 if sy-subrc <> 0.
 write: / '************** ERROR ***********************',
 / '** Missing Program Information for ',
 / pcode,
 scode,
 sy-datum(4),
 exit.
 endif.
ENDIF.
If pcode = 'SCW5S'.
WA_CREDIT-/BIC/ZINCUSDDS = discount.
WA_CREDIT-/BIC/ZPAYAMTUS = WA_CREDIT-/BIC/ZINCUSDDS * payrec-/bic/zpayper / 100.
WA_CREDIT-SUBTOTAL_4 = discount.
WA_CREDIT-/BIC/ZINC_QTY = ' '.
Endif.
If pcode = 'SCTMS'.
WA_CREDIT-/BIC/ZPAYAMTUS = quantity * payrec-/bic/zpayper / 100.
WA_CREDIT-/BIC/ZINCUSDDS = '0.00'.
WA_CREDIT-SUBTOTAL_4 = '0.00'.
WA_CREDIT-/BIC/ZINC_QTY = quantity.
Endif.
If pcode = 'SCTB'.
WA_CREDIT-/BIC/ZPAYAMTUS = '0.00'.
WA_CREDIT-/BIC/ZINCUSDDS = DISCOUNT.
WA_CREDIT-SUBTOTAL_4 = DISCOUNT.
WA_CREDIT-/BIC/ZINC_QTY = ' '.
Endif.
*Create ALV Grid to show the user what the record will look like in which they are creating.
Append wa_credit to alv_itab.
CALL SCREEN 100.
*& Module PBO OUTPUT
 text
MODULE alv_pbo OUTPUT.
SET PF-STATUS 'MAIN100'.
SET TITLEBAR 'MAIN100'.
IF g_custom_container IS INITIAL.
CREATE OBJECT grid1
EXPORTING i_parent = g_custom_container.
 CALL METHOD grid1->set_table_for_first_display
 EXPORTING
 i_structure_name = '/bic/azincosvi00'
 CHANGING
 it_outtab = alv_itab.
 CREATE OBJECT event_receiver.
 SET HANDLER event_receiver->handle_user_command FOR grid1.
 SET HANDLER event_receiver->handle_toolbar FOR grid1.
 CALL METHOD grid1->set_toolbar_interactive.
ENDIF.
ENDMODULE. " PBO OUTPUT
*& Module PAI INPUT
 text
MODULE alv_pai INPUT.
save_ok = ok_code.
CLEAR ok_code.
CASE save_ok.
 WHEN 'EXIT'.
 LEAVE PROGRAM.
 WHEN 'CANCEL'.
 LEAVE PROGRAM.
 WHEN 'BACK'.
 CALL METHOD grid1->free.
 CALL SELECTION-SCREEN '1000'.
 WHEN OTHERS.
 " DO NOTHING.
ENDCASE.
ENDMODULE. " PAI INPUT
*& Module 200_PBO OUTPUT
 text
MODULE 200_PBO OUTPUT.
Write at 5: 'Increase DSP Sales'.
Skip 1.
Write at 5: 'USER'.
Write at 15:'PROGRAM CODE'.
WRITE AT 25:'SUB CODE'.
WRITE AT 37:'DISCOUNTED SALES'.
WRITE AT 67:'PAY AMOUNT US'.
WRITE AT 80:'REASON'.
ENDMODULE. " 200_PBO OUTPUT

There are some problems with ok_code, you need to assign sy-ucomm at each module. Also the main problem was that you needed leave to list-processing and suppress dialog before writing. However, when you do this the screens calls change a little. You also needed to use the container correctly. Apply the correctons below and you'll be all set. Unfortunaley you will have to play around with calling the sel. screen (1000) from screen 100, I don't think call sel. screen 1000 will work properly there (you might need a custome screen instead). The user may be okay with kicking back out to sa38 after the alv display, however. Good luck and don't listen to the clowns' comments above. I once worked in that circus, Hey Guys.
Instead of this:
METHOD handle_user_command.
CASE e_ucomm.
WHEN 'CREATE'.
Insert /bic/azincosvi00 from wa_credit.
CALL METHOD grid1->free.
SET SCREEN '200'.
WHEN 'OTHERS'.
" DO NOTHING
ENDCASE.
ENDMETHOD.
DO THIS:
METHOD handle_user_command.
 CASE e_ucomm.
 WHEN 'CREATE'.
 Insert /bic/azincosvi00 from wa_credit.
 CALL SCREEN 200.
 WHEN 'OTHERS'.
 " DO NOTHING
 ENDCASE.
ENDMETHOD. "handle_user_command
Instead of this:
*Create ALV Grid to show the user what the record will look like in which they are creating.
Append wa_credit to alv_itab.
CALL SCREEN 100.
DO THIS:
IF g_custom_container IS INITIAL.
 CREATE OBJECT g_custom_container EXPORTING dynnr = '100'
 repid = sy-cprog
 ratio = '95'.
ENDIF.
IF grid1 IS INITIAL.
 CREATE OBJECT grid1 EXPORTING i_parent = g_custom_container.
ENDIF.
CREATE OBJECT event_receiver.
SET HANDLER event_receiver->handle_user_command FOR grid1.
SET HANDLER event_receiver->handle_toolbar FOR grid1.
SET SCREEN 100.
CALL SCREEN 100.
Instead of this:
MODULE alv_pbo OUTPUT.
SET PF-STATUS 'MAIN100'.
SET TITLEBAR 'MAIN100'.
IF g_custom_container IS INITIAL.
CREATE OBJECT grid1
EXPORTING i_parent = g_custom_container.
CALL METHOD grid1->set_table_for_first_display
EXPORTING
i_structure_name = '/bic/azincosvi00'
CHANGING
it_outtab = alv_itab.
CREATE OBJECT event_receiver.
SET HANDLER event_receiver->handle_user_command FOR grid1.
SET HANDLER event_receiver->handle_toolbar FOR grid1.
CALL METHOD grid1->set_toolbar_interactive.
ENDIF.
ENDMODULE. " PBO OUTPUT
DO THIS:
MODULE alv_pbo OUTPUT.
SET PF-STATUS 'MAIN100'.
SET TITLEBAR 'MAIN100'.
CALL METHOD grid1->set_table_for_first_display
EXPORTING
 i_structure_name = '/bic/azincosvi00'
CHANGING
 it_outtab = alv_itab.
CALL METHOD grid1->set_toolbar_interactive.
ENDMODULE. " PBO OUTPUT
Instead of this:
MODULE alv_pai INPUT.
save_ok = ok_code.
CLEAR ok_code.
CASE save_ok.
WHEN 'EXIT'.
LEAVE PROGRAM.
WHEN 'CANCEL'.
LEAVE PROGRAM.
WHEN 'BACK'.
CALL METHOD grid1->free.
CALL SELECTION-SCREEN '1000'.
WHEN OTHERS.
" DO NOTHING.
ENDCASE.
ENDMODULE. " PAI INPUT
DO THIS:
MODULE alv_pai INPUT.
ok_code = sy-ucomm.
CASE ok_code.
 WHEN 'EXIT'.
 LEAVE PROGRAM.
 WHEN 'CANCEL'.
 LEAVE PROGRAM.
 WHEN 'BACK'.
 CALL METHOD grid1->free.
 LEAVE PROGRAM.
* CALL SELECTION-SCREEN '1000'.
 WHEN OTHERS.
 " DO NOTHING.
ENDCASE.
ENDMODULE. " PAI INPUT
Instead of this:
MODULE 200_PBO OUTPUT.
Write at 5: 'Increase DSP Sales'.
Skip 1.
Write at 5: 'USER'.
Write at 15:'PROGRAM CODE'.
WRITE AT 25:'SUB CODE'.
WRITE AT 37:'DISCOUNTED SALES'.
WRITE AT 67:'PAY AMOUNT US'.
WRITE AT 80:'REASON'.
ENDMODULE. " 200_PBO OUTPUT
DO THIS:
*Take care of all your list output here
LEAVE TO LIST-PROCESSING.
SET PF-STATUS 'MAIN200'.
SET TITLEBAR 'MAIN200'.
SUPPRESS DIALOG.
WRITE AT 5: 'Increase DSP Sales'.
SKIP 1.
WRITE AT 5: 'USER'.
WRITE AT 15:'PROGRAM CODE'.
WRITE AT 25:'SUB CODE'.
WRITE AT 37:'DISCOUNTED SALES'.
WRITE AT 67:'PAY AMOUNT US'.
WRITE AT 80:'REASON'.
ENDMODULE. " 200_PBO OUTPUT
Add Moule:
MODULE 200_pai INPUT.
ok_code = sy-ucomm.
CASE ok_code.
 WHEN 'EXIT'.
 LEAVE PROGRAM.
 WHEN 'CANCEL'.
 LEAVE PROGRAM.
 WHEN 'BACK'.
 CALL SCREEN 100.
 WHEN OTHERS.
 " DO NOTHING.
ENDCASE.
ENDMODULE. " 200_PAI INPUT

New computer ~ Help with setting up

Hi everyone, Newbie here!
I am going to set my new computer up tomorrow. The computer I am using at present was installed and set up by someone else so this will be a great learning curve for me. Also I had Infinity installed by the engineer.
Is everything I need to install relating to my broadband available to download? What do I need altogether? I spoke to a BT chap on the phone and he said he would help by remote access. I am a bit nervous of this!
I need to ensure my computer is safe and secure and it all seems technically daunting. Norton security came with my Microsoft Office package. Is this better than McAfee (Net Protect Plus), do I need both? What about a key code scrambler (someone mentioned this to me). As you can see I need reassurance and help arghhhhhhh.
A step by step guide would be great!
Thanks
Solved!
Go to Solution.

It is best not to install any of the BT software, just connect your computer to the BT Home hub using an Ethernet cable, or by using the wireless key, if its a wireless connected computers.
See http://bt.custhelp.com/app/answers/detail/a_id/14964/~/getting-started-with-wireless
Using a direct cable connection is best, if you want to get maximum speed.
I would not allow anyone remote access, but if you have no choice, and cannot resolve the issue any other way, then make sure that it is as a direct result of you ringing BT, and not some random person ringing you at home, pretending to be from BT or even Microsoft.
Many people have been caught out by that type of call, and had their computer infected with spyware.
If you already have a trial version of Norton Security, then by all means use it until it expires, then uninstall it.
After that, you have the choice of using the free Microsoft Security Essentials, which is preferred by many forum members, or using BTs Netprotect which is free with some broadband packages. This has been known to make computers run more slowly though.
That is all you need.
If you have any problems, then please return here.
If you have any problems with BT Infinity, then please visit the Infinity board on this forum.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Need help with how to call VB proceedure to open Adobe reader pdf file from differnt folders

Using MS access 9.0.2720 visual basic proceedure to call Adobe reader to open a specific flle from a folder on my c drive.
useing the shell command , shellexecute is not available in the version I'm using.
I can call the Reader with this code: call shell "C:\Program Files (x86)\Adobe\Reader 11.0\Reader\AcroRd32.exe" and it will open reader, but
I can't seem to get it to open a specific PDF file, I tried
call shell "C:\Program Files (x86)\Adobe\Reader 11.0\Reader\AcroRd32.exe" & "(folderpath)\.95.pdf"
This use to work when I was running Xp and acrobat 5.0 , I am currentlt running windows 7
thanks in advance..

I am getting the exact error trying to down load bank statements but when I go to 'uncheck' the "Do not save encrypted page to disk" box it is ALREADY unchecked. Can't get my bank statements down loaded. Any other suggestions. Need help quick.

Need Help with setting up this Filter

Hi,
I need help making a filter sound like the one used in this youtube song.
I tried setting it up but I've had no success; even though I know for a fact that this filter was made in Logic Pro 9 according to the maker of this song.
I think there might be a bit of 'Fuzz-Wah' in there too but I've never really used that effect so any tips on that would be great, too.
Link: http://www.youtube.com/watch?v=tf017M8SZZE&feature=plcp
Any help with this would be widely appreciated.
Thank you :-)

It sounds like a simple hi Q filter sweep to me but getting close to the original synth sound that it is being used on is the challenge. It might well be that it is the filter on the synth itself is what is being swept. Either way, turn up the filter resonance on a band pass filter and sweep it with the lfo or adsr to modulate the filter cutoff if its the synth filter, or automate the filter frequency sweep if you use the channel filter.

Search Help with Web Dynpro call on another system

Hi all,
I have to create a search help with web dynpro on a field but the database is on another system... How can I do?
Many Thanks in advance...

I would use a search help exit. Nothing WDA specific here, as this has been possible long before WDA came around. With a search help exit you define the search help like normal, but instead of database table or view being the source of selection, you have a function module. Within the coding of this function module you can call an RFC to read data from another system or call a web service if you need to bridge over to something that isn't ABAP based.
You can read more about Search Help Exits here:
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/cf/21ee52446011d189700000e8322d00/frameset.htm

Need help with Set-ADUser command

I need a little help with the following command. Im new to PS and I have found this command but it is only one user at a time. I need to be able to update ALL users in AD.
My goal is this. Someone before me set all Users Home numbers to 1234567899 and I need to remove that and leave it blank. The command below allows me to do that but only one user at a time by entering their SAMID.
Is there a way to do this for everyone in AD ?
Set-AdUser –Identity SAMID –HomePhone $NULL

Yeah sure -
Get-Aduser -filter * -properties SamaccountName | Select SamAccountName | % {Set-Aduser -identity $_.SamaccountName -HomePhone $null}

Help with set(index, object) please / new to java

private static void setDobject(Rectangle [] setrect)
 LinkedList<Rectangle> rects = new LinkedList<Rectangle>();
 Rectangle myrectangle = new Rectangle(9.0,9.0);
 rects.set(1,myrectangle);
 for(Rectangle x : setrect)
 System.out.print("Rectangle: ");
 System.out.println(x.getLength() + " by " + x.getWidth());
 } //End of for loop
 } //End of unsorted
 } the other previous code works, i have used the add(object) and it works here is the code for that:
private static void addDobject(Rectangle [] addrect)
 LinkedList<Rectangle> rects = new LinkedList<Rectangle>();
 Rectangle myrectangle = new Rectangle(9.0,9.0);
 rects.add(myrectangle);
 for(Rectangle x : rects)
 System.out.print("Rectangle: ");
 System.out.println(x.getLength() + " by " + x.getWidth());
 } //End of for loop
 System.out.println();
 } //End of unsorted
this is the output error it is giving me :
Part 1 : An Array List of Rectangles
Enter length or 999 to exit: 3
Enter width: 2
Enter length or 999 to exit: 1
Enter width: 2
Enter length or 999 to exit: 10
Enter width: 20
Enter length or 999 to exit: 999
Rectangle: 3.0 by 2.0
Rectangle: 1.0 by 2.0
Rectangle: 10.0 by 20.0
Display Object with added item
Rectangle: 3.0 by 2.0
Rectangle: 1.0 by 2.0
Rectangle: 10.0 by 20.0
Rectangle: 9.0 by 9.0
Displaying Objects with SET item
Exception in thread "main" java.lang.IndexOutOfBoundsException: Index: 1, Size:
0
at java.util.LinkedList.entry(LinkedList.java:365)
at java.util.LinkedList.set(LinkedList.java:328)
at Lab11.setDobject(Lab11.java:129)
at Lab11.main(Lab11.java:78)
Press any key to continue...
finally here is the Rectangle class i'm using:
public class Rectangle
 private double length; // Instance variables
 private double width;
 public Rectangle(double l, double w) // Constructor method
 length = l;
 width = w;
 } // end Rectangle constructor
 public double getLength() // getter
 return length;
 } // end getLength
 public double getWidth() // getter
 return width;
 } // end getWidth
 public void setLength(double l) // setter
 length = l;
 } // end setLength
 public void setWidth(double w) // setter
 width = w;
 } // end setWidth
 public double calculateArea() // calculation method
 return length * width;
 } // end calculateArea
 public void displayRectangle() // display method
 System.out.println("Rectangle Length = " + length);
 System.out.println("Rectangle Width = " + width);
 } // end displayRectangle
} // Rectangle ClassHope you can help guys! thanks!

LinkedList<Rectangle> rects = new LinkedList<Rectangle>();rects is an empty LinkedList at this point. It has no elements added to it.
rects.set(1,myrectangle);So you can't set the item at index 1 (the 2nd element in the list) because it doesn't even exist. You need to add items to it.

Help with setting a MDX goal expression in SSAS

Our data is updated monthly and the last date of available data can be anywhere from 45-75 days behind. For example, data is current through 6/30/2014
as of 8/25/2014.
I have a Time dimension hierarchy named [Calendar] with [Year]>[Half Year]>[Quarter]>[Month]>[Date]
I have a measure, [Measures].[Fatalities] set as a calculated member.
I have a KPI with [Measures].[Fatalities] set as the Value Expression. My issue is with setting up the goal expression.
I am trying to set a goal expression that is a percent reduction for a 5-year baseline average (Year-7:Year-3). So for the current year (2014, with data through
June 2014), the goal would be a 20% reduction of the average of the Jan-Jun 2007, Jan-Jun 2008,Jan-Jun 2009,Jan-Jun 2010,Jan-Jun 2011.
I have set up the following MDX as the goal expression:
.8*((
([Measures].[Fatalities],
PARALLELPERIOD([Time].[Calendar].[Year],7,[Time].[Calendar].CurrentMember))
+
([Measures].[Fatalities],
PARALLELPERIOD([Time].[Calendar].[Year],6,[Time].[Calendar].CurrentMember))
+
([Measures].[Fatalities],
PARALLELPERIOD([Time].[Calendar].[Year],5,[Time].[Calendar].CurrentMember))
+
([Measures].[Fatalities],
PARALLELPERIOD([Time].[Calendar].[Year],4,[Time].[Calendar].CurrentMember))
+
([Measures].[Fatalities],
PARALLELPERIOD([Time].[Calendar].[Year],3,[Time].[Calendar].CurrentMember))
)/5
The problem is that the goal is taking the entire year average at the year level of the Calendar hierarchy. For example, in the attached screenshot, the
Fatalities Goal would be empty when the fatalities is empty, and more importantly, the goal at the Year level of the Calendar hierarchy would only be the sum of Jan-Jun goal. The Fatalities Goal in this example should read 549.28 at the Calendar 2014
Year level and the status would still be green.
http://i.imgur.com/peHD9Wl.png

you might find this app interesting: http://ivolume.en.softonic.com/mac.

[SOLVED] Need help with setting up X

Hello guys am new to the forum and this is my first post here. I am in need of a little help.
Need help with X configuration. It starts like this, I installed xorg-server , xorg-utils, xorg-server-utils. When I tried installed xorg-init it says no package, anyway I ignored and moved on.
Now I installed regular mesa stuff and installed xf86-video-ati driver for my HD4250 graphics adapter. with libgl and ati-dri (I have old arch wiki print so it mentioned to install those while newer doesn't list some stuff)
Now the problem is that Xorg -configure doesn't work with newer X and nor the packages has generated /etc/X11/xorg.conf file.
Anyway I created the file manually and added each and every section as mentioned in the "old" guide that I have.
I even added a /etc/X11/xorg.conf.d/20-radeon.conf file for my graphics card with the content as
Section "Device"
Identifire "r"
Driver "radeon"
EndSection
After manually creating all such files I installed x-term, xclock and twm. But when I tried to start X by startx or Xinit it says command not found. Add to that a simple X shows couple of errors.
Please see the errors here Paste #399362 | LodgeIt!
Some more questions : My old guide mentioned to install HAL while newer guide on the net mention DBUS. Though I have added DBUS to be on the safe side but why not HAL ? Is it because of Udev ?
So please help me getting X up and running.
Regards
Last edited by Shashwat (2011-06-04 09:47:47)

Ok I sorted out the misprints in the file and installed xinit but still can't get it to work.
1. There are few errors in xorg.conf that I cannot make it out.
2. The X output says no screen found. ?
http://paste.pocoo.org/show/399383/
Now when I add EndSection at the last its says invalid parameter and when I remove it, I get an error "No EndSection, EOF missing"
Kind of bugging
Please do help.

Help with setting up Caller-id on FXO in 2911 H.323 gateway.

Similar Messages

Maybe you are looking for