Help with starting raid on the k9a2 platnium

ok well i just got a k9a2 platnium
specs- amd 9950 BE edition
4gb of 800mhz ddr2 cas 3
2x 80 gb hard drives
1x 640gb hard drive
ati hd 4870
k9a2 platnium
750 watt corsair psu
ok. i finished my computer. and i wanted to raid the two 80's. but for some reason it would never show up as a single drive when i install windows vista ultimate 64bit.
so i installed my vista on the 640gb hd.
how do i raid 0 my two 80 gb.
What i did now-
plugged in the two sata(the 80 gb's) into the red slots.
installed the raid driver for windows vista
booted computer. and press CTRL+F
pressed 2. and put my two 80's in raid 0 mode. i dunno what to put for the other options such as striping and stuff.
thats all i did for now.
can someone help me

I don't understand where you're at or what you're trying to acheive here ???
You've formatted the 640gb disk, so now where is your OS?
There was absolutely no need to do that, what myself and BOSSKILLER are trying to get you to do is to create a partition on your RAID array, so WIndows can use it, this is done by clicking on 'Drive Management' in your Computer Management screen. (right-click My Computer and select Manage)
The RAID array will appear as one 'disk' in the disk list (lower right window), but will be empty, just right-click inside it, and select Create Partition, and then format it.
[My screenshot below is from my computer, but I only have one hard disk, and no array, but your array will be shown in the lower right hand panel, will show as 160gb (2x 80gb)]
If you still cannot get the grasp of this, I suggest you get someone who knows how to do this to help you.

Similar Messages

  • TS1702 I just updated numbers to newest version and found that numbers quits to home screen when I tap the information icon on "function  help", it starts to load the "help" then quits  this happens on both my ipad3 & iphone5

    2/3/14: I just updated numbers to newest version and found that numbers quits to home screen when I tap the information icon on "function  help", it starts to load the "help" then quits. It happens on both my ipad3 & iphone5. I tried restarting the devices but it didn't help.

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased. http://support.apple.com/kb/ht1430
    iOS 7: Help with how to fix a crashing app on iPhone, iPad (Mini), and iPod Touch
    http://teachmeios.com/help-with-how-to-fix-a-crashing-app-on-iphone-ipad-mini-an d-ipod-touch/
    Troubleshooting apps purchased from the App Store
    http://support.apple.com/kb/TS1702
    Delete the app and redownload.
    Downloading Past Purchases from the iTunes Store, App Store and iBooks Store
    http://support.apple.com/kb/ht2519
     Cheers, Tom 

  • I have an itouch, most songs i got off my cd's. i have a new laptop and want to put songs from itouch to laptop.I can only get the songs that i purchased onto the laptop? need help with how to get the rest from itouch to laptop please??

    i have an itouch, most songs i got off my cd's. i have a new laptop and want to put songs from itouch to laptop.I can only get the songs that i purchased onto the laptop? need help with how to get the rest of the songs (from my cd's) from itouch to laptop please??

    See this previous discussion:
    Recovering your iTunes library from your iPod or iOS device: Apple Support Communities

  • Hi guys can someone help with a query regarding the 'podcast app' why do they not have all the episodes that relate to one show available why only half or a selected amount

    Hi guys can someone help with a query regarding the 'podcast app' why do they not have all the episodes that relate to one show available why only half or a selected amount

    THanks...but some days they have all the episodes right back to the very first show...ive downloaded a few but they are only available every now and then which makes no sense...why not have them available the whole time ??

  • Need help with LikeFilter for querying the keyset instead of value

    Hi,
    I'm looking for help with the LikeFilter.
    I need to query the cache to get all entries with key starting with a particular string.
    I could see samples using LikeFilter for querying the values in the cache but not the keyset.
    Can someone help?
    E.g:
    Cache Entries:
    abc123 - value1
    abc234 - value2
    bcd123 - value3
    I want to get all entries with key starting with 'abc'.
    thanks,
    rama.

    NJ, thanks for the quick reply.
    I tried something similar (as below) but this code gives me 'java.lang.NoClassDefFoundError: com/tangosol/util/ValueExtractor'.
    KeyExtractor extractor = new KeyExtractor("getKey");
    Filter filter = new LikeFilter(extractor, id+":%",'-',false);
    -rama.
    Edited by: 911950 on Feb 2, 2012 1:18 PM

  • Need help with repeating Subforms on the next page

    I have created two different flowable repeating subforms, for example - subform1 and subform2 in a document with an action button for each to add another subform on the next page.  After subform2, I have two buttons - one to add subform1 again or add subform2 on the next page. When I click the button, Livecycle adds the new subform as commanded but the subform is added directly after the previous same subform not on the next page as requested.  I have tried to change the pagination settings but nothing seems to work.  Can anyone help me define how to get the repeating subform to add to the next page and not after the same subform?

    OK, so here's what I would do.
    1. Wrap your subform1 and subform2 in a subform. I'll call it sfMaster.
    2. Change your minimum instance for subform1 and 2 to 0 or uncheck the box, and set the initial count to 1. (That way you get at least one of each when we start.)
    3. have the buttons create a new instance of sfMaster, then remove the instance of the subform you didn't want within that most recent instance.
    So, what the user sees is a new subform1 or 2 each time they hit a button. And they'll appear in whatever order they choose it. The user doesn't have to know that what is actually happening is the creation of a new "master" subform that holds both subform1 and 2.
    To help illustrate what I mean, I've added a pink border around sfMaster and colored subform1 and 2.
    Binding options for Subform2 (Subform1 would be similar)
    What it looks like in action
    If you want to guarantee it appears on the next page, you'll need to add the conditional break from earlier. Keep working with it to get the settings just right. You may even want a docReady() event that creates two sfMaster's and sets one to have Subform1 and the other to have Subform2.

  • Help with start up probs after force quit

    Hi there . I think I'm royally fckd. I was on blogger and my screen froze no cursor move nothing had to force quit. Now every time I try to turn on the MacBook Air all I get is a black screen and that start up noise over over over again . still black screen and no log in page . Is there a way to fix this or is it royally gone to mac heaven.help with thanks .

    your force quit wouldn't cause an inability to powerup.   Black screen on every powerup?
    SSD or logic board fault likely.
    Contact Apple for diagnostic/ repair.
    Anything in your Air can be fixed yes. 

  • Course for help with X Raid

    Hi All,
    My boss has given my the OK to go on courses for get up to scratch with X Serve so I'm going to go on the Mac OS X Server Essentials 10.5 4 day course but I also want to know X Raid setup. Is there anything else that go on to help with this?

    Hi
    If you are thinking the course covers the XServe then you might be mistaken. OSX Server is not the XServe, its any apple hardware that meets OSX Server's minimum requirements. It may well be mentioned on the course?
    The XServe is dedicated hardware built for Server use although you can install OSX Client on it if you wish. To that end and as far as I know there are no specific courses for hardware other than Apple Certified Technician. This used to be ACPT and ACDT before apple unified the hardware courses under one umbrella.
    As for the XServe RAID - apart from the fact that it is a discontinued product and has been for the last 2-3 months - I don't think there has ever been a specific course for it? Leastways not this side of the pond. There are plenty of manuals/user guides available for both products either on the Apple website or on the disks that come with both models.
    http://www.apple.com/support/manuals/xserve/
    http://www.apple.com/support/manuals/macosxserver/
    Tony

  • Help with software RAID on system disk

    I've been trying to get my OS system disk mirrored using diskutil's software RAID (my server has 2 internal 80GB drives). I did what homework I could and here's where I'm stuck. I'm running 10.4.3.
    n506:~ root# uname -a
    Darwin n506.local 8.3.0 Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC Power Macintosh powerpc
    n506:~ root#
    According to my research, I needed to boot from an OS disk other than the one I want to mirror, so I installed a second instance of OS X on my second drive, booted on that and ran diskutil enableRAID against the system drive I want to protect. This appeared to work. A new disk device was added (the RAID device) with its only component being the disk I ran enable RAID on. Then I booted from that disk. Here's the problem.
    When I run diskutil addToRAID to add the second disk to the raid group, the command does partition the disk the same way the primary is partitioned (according to diskutil list), but the command always fails with this error:
    n506:~ root# diskutil addToRAID member disk0 disk2
    2006-05-27 23:49:50.012 DiskManagementTool[362] AppleRAIDUpdateSet failed to modify the set (null)
    There was an error adding the disk to the RAID (-9960)
    n506:~ root#
    The system log shows this:
    n506:~ root# tail -1 /var/log/system.log
    May 27 23:49:50 n506 kernel[0]: AppleRAIDMember::readRAIDHeader: failed, no header signature present on disk0s4.
    n506:~ root#
    [NOTE: I should add here that, for reasons unknown to me, my system created /dev/disk0 from the drive in the second bay, and /dev/disk1 from the drive in the first bay (the primary disk I'm trying to mirror). I have no idea why OS X set up the devices like that, but I haven't really worried about it]
    I've done what research I could and have found no information on this problem. I've tried zero-ing the second disk and rerunning the command (along with rebooting), but I always seem to get this error.
    Any help would be greatly appreciated. I've been at it for days now and I'm really frustrated.
    G5 server Mac OS X (10.4.3)

    If anyone out there is interested in this thread, I upgraded to 10.4.6 and tada:
    n506:~ root# diskutil addToRAID member disk0 disk2
    The disk has been added to the RAID
    n506:~ root# diskutil checkRAID
    RAID SETS
    Name: Disk1
    Unique ID: 1CC5982A-B353-438C-A69F-8D66924449C0
    Type: Mirror
    Status: Degraded
    Device Node: disk2
    Apple RAID Version: 2
    # Device Node UUID Status
    1 disk0s3 219611E9-F35F-48A4-BD4F-F56038094613 2% (Rebuilding)
    0 disk1s3 0EDD559B-FEE8-4F73-B94D-AF5590AD8BF2 Online
    n506:~ root#

  • Call object was called with start date in the previous month

    We have a single cycle maintenance plan for 30 days.
    Shift Factor Late Compl.   : 100%
    Tolerance                    :  10%
    Shift Factor Early Compl. :  100%
    Tolerance                    :    10%
    Cycle modification factor:    1
    Factory calendar            :  NIL
    Call horizon                    : 100%
    Scheduling period          :  90 DAY
    Scheduling indicator       : Time
    Call no . 11 was a plan date of 14.08.2009 has completion date 14.08.2009. Schedule type/status has "scheduled complete".
    Call no. 12 was called on 13.09.2009 which is in the past.
    Can someone explain why the system called the order with a starting date in the previuos month , that is , 13.09.2009.
    And how to rectify it to make it current date for the next call object?
    Thanks,
    Manohar

    I checked the algorithm for call no. 12
    Start of Cycle                07.08.2008
    Last planned date         14.08.2009
    Compl.Predecess           14.08.2009        Absolute shift                +   0 Da
    Planned cycle/offset      +    30 Da          Relative shift            0 % =   0 Da
    Shift                                 +     0 Da           erance value           0 % =   0 Da
    Planned Dates Due   13.09.2009    Completed on
    Last call on              15.10.2009    Called by               IP1020091015
    Workorder generated has start date 13.09.2009.
    Should we restart this plan , as the start dates in call object are at least 1 month old ?
    Thanks,
    Manohar

  • Help with starting up G3 that won't power up

    Hello,
    I have a powerbook G3 500mhz firewire with the first OSX version that I'm trying to get started up. It was working fine a few months ago (the last time I used it). Not it won't start up at all, no sounds or anything, even when plugged in. I'm sure there hasn't been any damage to it as it's been sitting on my desk in the same position since the last time I used it.
    I remember this happening years ago, and I was told to leave it plugged in for a few days for one of the batteries to recharge, and that fixed it that time. This time I left it plugged in for a week but still no progress.
    Any ideas?
    thanks.

    ble,
    If I just may add to Tom's reply. IFixit's instructions are great, but they don't show you the quickest and simplest way to the hardware, often having you remove parts unnecessarily.
    All you need to do to access the PRAM battery is this:
    -Remove all power.
    -Remove the optical drive from the bay.
    -Support the back of the powerbook display so the 'book does not tilt backwards.
    -Lift off the keyboard but do NOT disconnect the keyboard; just lay it face down on the palm rest.
    -In the picture, you can see the white connector from the batteries to the logic board. Use needlenose plies to pull it up if necessary.
    -Now without any reassembly, connect the power adapter and start. If successful, press/hold the power button until the Pismo shuts off.
    -Reconnect the PRAM battery and again try starting. If successful, shut down and reassemble. If it won't start, unplug the PRAM battery and reassemble.
    If the 'book fails to start after reconnecting the battery, it probably has an internal short and needs to be replaced. Your Pismo will run fine without this battery connected.
    Message was edited by: jpl

  • Need help with finding a workaround: the shotcut ctrl+click opens 2 tabs in my case

    Hello!
    I have several links with an onclick event, which contains some javascript handling and window.open() after it, and they have attribute href="javascript:void(0);" as well.
    When user try Ctrl+click Firefox opens him 2 tabs: the first one with "right" content and the second with javascript:void(0).
    I've tried to set href="#" and in this case Ctrl+click works as I want, but on the original tab the user is redirected by the browser to the top of the page. The empty attribute (href="") also results 2 tabs. Maybe there is some value of the href attribute with which everything will work as I want? I've fed up with this and will be appreciated a lot if you help. Thanks.
    == This happened ==
    Every time Firefox opened
    == User use Ctrl+click

    I won't be searching thru all that code to try to find something relevant to your post, but if you are using a Loader to load the images, you can get the width and height as soon as the loading is complete using the loader object (loader.width, loader.height).  You just need to wait until loading is complete, so you'll need a listener for that if you don't have one already.

  • Problem with starting Timecode in the Timecode effect

    hi everyone,
    I have a problem with the timecode effect in my sequence. The strating time of the sequence ist 09:59:50:00, I copy/pasted it into "Starting Timecode" in the Timecode effect controls panel and chose "Generate" from the Timecode Source options, but the numbers shown on the display were different as the starting timecode I set. So I had to change the starting timecode in the effect controls panel to 09:59:14:01 and now it shows the right timecode on the display. how is it possible? any ideas where this difference could come from? the frame rate is set correctly. is this a bug in the PPro CC 7.1? I had to downgrade from 7.2.1, because of many problems it was causing.
    cheers,
    Michal
    Adobe Premiere Pro CC 7.1
    Windows 8
    Intel(R) Core(TM) i7-4770K CPU @ 3.50GHz
    32 GB RAM
    NVIDIA GeForce GTX 780

    Hi Jim,
    unfortunately I have still the same problem with timecode after upgrading to 7.2.2. Do you have any idea what could be the cause of this?

  • Please help with start problem of my new X61s

    I baught my X61s 2 weeks ago. It was received with vista home installed. I downgraded it to XP myself 1 week ago and it was working very well. Today, when I turned on the machine, nothing appeared on the screen, and I only hear about 7 beeps. I tried to turn off and turn on the machine several times, but no difference. I don't know what happen.
    Please help me! Thanks.

    Per the magic beep decoder ring that might mean bad DIMM or system board.
    I don't work for Lenovo. I'm a crazy volunteer!

  • Help with 5.5 on the Cloud and on an iMac desktop

    I work with another person on the layout of a magazine using InDesign. We're 1,000 miles appart. For the last two years we've been shuttling the layout back and fort successfully. We both had/have 5.5. He recently bought a new mac and signed up for the Cloud. I sent him my file, he made changes and sent it back to me. I cannot open it. I get a CANNOT OPEN FILE message box with a long list of plug-ins that I need. Now were in trouble with a deadline 10 days away. He can open my 5.5 files, but I can't open his. I'm very happy with InDesign on my desktop and have no interest in moving to the Cloud.

    If you have to work with someone in the cloud you have to work at least with CS6 and ask him to work with CS6 which is able to get from the cloud and which is available to get as buy version.
    If he insist to work with CC (a lot of reasons are given) you have to go to the cloud too.
    The exchange of InDesign files as IDML is not very recommandable as there a lot of changes in the layout after converting and opening in the other version.
    Yes, InDesign is opening an older version's file but not a newer version's file and that is the problem you are running in.

Maybe you are looking for