Help with VLANs on SG200-18 and two SG200-08 switches
Hi everybody. My apologies but I'm only average at best with my CISCO skills. I have simple setup running a few network devices connected via 3 CISCO switches. It's small office and there are two rooms - one with servers and one with printer and pc's. Each room has 8-port SG200-08 switch.
Router/ firewall is Sonicwall TZ215 and it handles internal routing between VLAN's. Each SG200-08 was connected directly to TZ215 (no SG200-18 yet) and VLANs were working perfectly. Please see diagram below...
Problems started when I added in the middle larger SG200-18 to handle extra devices. Whatever I'm doing wrong but I can't make VLANs work anymore. Something I'm not setting up correctly in SG200-18.
Please help me to setup VLANS here - tagged, untagged, PVID, trunk........ I'm completely lost and already had to reset SG200-18 twice.
My working setup without 18 port switch was like this.
SG200-08 (1)
g1 Trunk 1 1U,100T
g2 Trunk 1 1U
g3 Trunk 1 1U
g4 Trunk 1 1U
g5 Trunk 1 1U
g6 Trunk 1 1U SERVER3
g7 Trunk 100 100U SERVER1
g8 Trunk 100 100U SERVER2
SG200-08 (2)
g1 Trunk 1 1U,50T,200T
g2 Trunk 1 1U
g3 Trunk 1 1U
g4 Trunk 1 1U PC1A
g5 Trunk 1 1U PC1B
g6 Trunk 50 50U PC2A
g7 Trunk 50 50U PC2B
g8 Trunk 200 200U NETWORK PRINTER
Thank you in advance.
Hello,
Small switches would remain untouched but 200-18 needs to have the following settings:
g15 Trunk 1 1U,100T
g16 Trunk 1 1U,50T,200T
g17 Trunk 1 1U,50T,200T
g18 Trunk 1 1U,50T,100T,200T
Sonicwall now would have only one port connected to SG200-18 with settinngs matching port g18 on big switch.
If you notice there is a change as now you would have only 1 port connecting your network to the Sonicwall, would advise you to use port 17 or 18 since they are uplink ports.
If you have tried to connect two ports to big switch STP would block one of the ports.
Let me know how it is going :-)
Aleksandra
Similar Messages
-
I've tried reseting my sync accounts the way all of the help articles say, but my computer and two android devices just will not sync with this new FF Sync version.
I've tried unregistering the device sync accounts, removing the accounts, reinstalling FF on all devices, etc.
Nothing works. Please help.Hi mongoose00318,
On the android devices in the Account section of your OS settings, please make sure that the account is not listed under "Firefox Sync (deprecated)" this is the old sync. Firefox for Android may need to be reinstalled and the Firefox Sync (depricated) account removed from the device.
NOTE: DO NOT do this if there is data on the devices that have not obviously synced yet. An alternative is to visit accounts.firefox.com to see if you are logged into the device on the new sync sign in page.
Does this help? -
Help with if statement in cursor and for loop to get output
I have the following cursor and and want to use if else statement to get the output. The cursor is working fine. What i need help with is how to use and if else statement to only get the folderrsn that have not been updated in the last 30 days. If you look at the talbe below my select statement is showing folderrs 291631 was updated only 4 days ago and folderrsn 322160 was also updated 4 days ago.
I do not want these two to appear in my result set. So i need to use if else so that my result only shows all folderrsn that havenot been updated in the last 30 days.
Here is my cursor:
/*Cursor for Email procedure. It is working Shows userid and the string
You need to update these folders*/
DECLARE
a_user varchar2(200) := null;
v_assigneduser varchar2(20);
v_folderrsn varchar2(200);
v_emailaddress varchar2(60);
v_subject varchar2(200);
Cursor c IS
SELECT assigneduser, vu.emailaddress, f.folderrsn, trunc(f.indate) AS "IN DATE",
MAX (trunc(fpa.attemptdate)) AS "LAST UPDATE",
trunc(sysdate) - MAX (trunc(fpa.attemptdate)) AS "DAYS PAST"
--MAX (TRUNC (fpa.attemptdate)) - TRUNC (f.indate) AS "NUMBER OF DAYS"
FROM folder f, folderprocess fp, validuser vu, folderprocessattempt fpa
WHERE f.foldertype = 'HJ'
AND f.statuscode NOT IN (20, 40)
AND f.folderrsn = fp.folderrsn
AND fp.processrsn = fpa.processrsn
AND vu.userid = fp.assigneduser
AND vu.statuscode = 1
GROUP BY assigneduser, vu.emailaddress, f.folderrsn, f.indate
ORDER BY fp.assigneduser;
BEGIN
FOR c1 IN c LOOP
IF (c1.assigneduser = v_assigneduser) THEN
dbms_output.put_line(' ' || c1.folderrsn);
else
dbms_output.put(c1.assigneduser ||': ' || 'Overdue Folders:You need to update these folders: Folderrsn: '||c1.folderrsn);
END IF;
a_user := c1.assigneduser;
v_assigneduser := c1.assigneduser;
v_folderrsn := c1.folderrsn;
v_emailaddress := c1.emailaddress;
v_subject := 'Subject: Project for';
END LOOP;
END;
The reason I have included the folowing table is that I want you to see the output from the select statement. that way you can help me do the if statement in the above cursor so that the result will look like this:
emailaddress
Subject: 'Project for ' || V_email || 'not updated in the last 30 days'
v_folderrsn
v_folderrsn
etc
[email protected]......
Subject: 'Project for: ' Jim...'not updated in the last 30 days'
284087
292709
[email protected].....
Subject: 'Project for: ' Kim...'not updated in the last 30 days'
185083
190121
190132
190133
190159
190237
284109
286647
294631
322922
[email protected]....
Subject: 'Project for: Joe...'not updated in the last 30 days'
183332
183336
[email protected]......
Subject: 'Project for: Sam...'not updated in the last 30 days'
183876
183877
183879
183880
183881
183882
183883
183884
183886
183887
183888
This table is to shwo you the select statement output. I want to eliminnate the two days that that are less than 30 days since the last update in the last column.
Assigneduser....Email.........Folderrsn...........indate.............maxattemptdate...days past since last update
JIM......... jim@ aol.com.... 284087............. 9/28/2006.......10/5/2006...........690
JIM......... jim@ aol.com.... 292709............. 3/20/2007.......3/28/2007............516
KIM......... kim@ aol.com.... 185083............. 8/31/2004.......2/9/2006............. 928
KIM...........kim@ aol.com.... 190121............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190132............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190133............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190159............. 2/13/2006.......2/14/2006............923
KIM...........kim@ aol.com.... 190237............. 2/23/2006.......2/23/2006............914
KIM...........kim@ aol.com.... 284109............. 9/28/2006.......9/28/2006............697
KIM...........kim@ aol.com.... 286647............. 11/7/2006.......12/5/2006............629
KIM...........kim@ aol.com.... 294631............. 4/2/2007.........3/4/2008.............174
KIM...........kim@ aol.com.... 322922............. 7/29/2008.......7/29/2008............27
JOE...........joe@ aol.com.... 183332............. 1/28/2004.......4/23/2004............1585
JOE...........joe@ aol.com.... 183336............. 1/28/2004.......3/9/2004.............1630
SAM...........sam@ aol.com....183876.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183877.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183879.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183880.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183881.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183882.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183883.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183884.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183886.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183887.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183888.............3/5/2004.........3/8/2004............ 1631
PAT...........pat@ aol.com.....291630.............2/23/2007.......7/8/2008............ 48
PAT...........pat@ aol.com.....313990.............2/27/2008.......7/28/2008............28
NED...........ned@ aol.com.....190681.............4/4/2006........8/10/2006............746
NED...........ned@ aol.com......95467.............6/14/2006.......11/6/2006............658
NED...........ned@ aol.com......286688.............11/8/2006.......10/3/2007............327
NED...........ned@ aol.com.....291631.............2/23/2007.......8/21/2008............4
NED...........ned@ aol.com.....292111.............3/7/2007.........2/26/2008............181
NED...........ned@ aol.com.....292410.............3/15/2007.......7/22/2008............34
NED...........ned@ aol.com.....299410.............6/27/2007.......2/27/2008............180
NED...........ned@ aol.com.....303790.............9/19/2007.......9/19/2007............341
NED...........ned@ aol.com.....304268.............9/24/2007.......3/3/2008............ 175
NED...........ned@ aol.com.....308228.............12/6/2007.......12/6/2007............263
NED...........ned@ aol.com.....316689.............3/19/2008.......3/19/2008............159
NED...........ned@ aol.com.....316789.............3/20/2008.......3/20/2008............158
NED...........ned@ aol.com.....317528.............3/25/2008.......3/25/2008............153
NED...........ned@ aol.com.....321476.............6/4/2008.........6/17/2008............69
NED...........ned@ aol.com.....322160.............7/3/2008.........8/21/2008............4
MOE...........moe@ aol.com.....184169.............4/5/2004.......12/5/2006............629
[email protected]/27/2004.......3/8/2004............1631
How do I incorporate a if else statement in the above cursor so the two days less than 30 days since last update are not returned. I do not want to send email if the project have been updated within the last 30 days.
Edited by: user4653174 on Aug 25, 2008 2:40 PManalytical functions: http://download-west.oracle.com/docs/cd/B10501_01/server.920/a96540/functions2a.htm#81409
CASE
http://download.oracle.com/docs/cd/B10501_01/appdev.920/a96624/02_funds.htm#36899
http://download.oracle.com/docs/cd/B10501_01/appdev.920/a96624/04_struc.htm#5997
Incorporating either of these into your query should assist you in returning the desired results. -
need help with how to reset bios and admin password to reformat hard drive in 8440p elitebook? removal of cmos, resetting laptop, using cccleaner, windows password recovery and hiren's was noneffective, any help is appreciated. thanks
Hi,
As your notebook is a business class machine, security is more stringent - the password is stored in non-volatile memory and there are no 'backdoor' passwords. Your best option would be to contact HP regarding this.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Can anyone help with issue whereby Music, Podcasts and Audiable Book Apps keep stopping when listing via Headphones following IOS 7.06 Updates on Iphone 4?
I have tried the following all ready:
Resetting Phone
Resetting Settings on phone
Change Headsets to speakers
Reinstalled Phone
Updated to IOS 7.1
No of the above has resolved the issue does anyone have any ideas?Can anyone help with issue whereby Music, Podcasts and Audiable Book Apps keep stopping when listing via Headphones following IOS 7.06 Updates on Iphone 4?
I have tried the following all ready:
Resetting Phone
Resetting Settings on phone
Change Headsets to speakers
Reinstalled Phone
Updated to IOS 7.1
No of the above has resolved the issue does anyone have any ideas? -
Hi i would like help with:
When I draw circle and add stroke I can not see stroke
I use Photoshop CS 5Make sure the stroke is set to a color and not to the symbol that appears here for Fill
-
How to resolve A VMWare portgroup with VLAN ID 0 cannot be founf on virtual switch vSwitch0.
Hi All,
I have deployed Microsoft private cloud using SCVMM, SCOM, SCCM, SCSM, SCO and SCSM Portal...
Also, i am using cloud service process pack runbooks and offerings for my vm provisioning in VM Ware platform...
After submitted the request vm got created but it is throwing an error in SCVMM jobs:
A VMWare portgroup with VLAN ID 0 cannot be found on virtual switch vSwitch0...
VLAN ID of the existing virtual switch vSwitch is 48 and that we cannot change...also we cannot create a new vswitch in DC...
How can i resolve this error...
Thanks in advance for your help...
Regards,
Sudheesh M AHi Alexander,
Thank for answering. I asked custumer to send some config file from the switch. I don´t how complete is this, but, regarding "mls cos" entries, we have:
no aaa new-model
switch 1 provision ws-c2960x-48ts-l
ip domain-name ecs.local
login on-failure trap
login on-success log
vtp mode transparent
mls qos
crypto pki trustpoint TP-self-signed-1837850112
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1837850112
revocation-check none
rsakeypair TP-self-signed-1837850112
interface GigabitEthernet1/0/1
switchport access vlan 235
switchport mode access
srr-queue bandwidth share 1 70 25 5
priority-queue out
mls qos trust dscp
service-policy input ACCESS_INGRESS
interface GigabitEthernet1/0/2
switchport access vlan 235
switchport mode access
srr-queue bandwidth share 1 70 25 5
priority-queue out
mls qos trust dscp
service-policy input ACCESS_INGRESS
interface GigabitEthernet1/0/48
switchport access vlan 235
srr-queue bandwidth share 1 70 25 5
priority-queue out
mls qos trust dscp
service-policy input ACCESS_INGRESS
Is these entries make any sense for the behavior we are facing?
Thanks -
Any help with Linkskys PrintServer PSUS4, G4 and HP1200 in a wired network?
Wired the house with cat 6e wire. Verizon FIOS is working great on a network of Mac G4 Powerbook; Mac G4 PowerPC and two PC's.
Hooked in a Linksky's PrentServer to the network - the Mac won't recognize the HP 1200 printer.
What settings should I be putting on the Mac --- ?????
any help appreciated.Hello Cal87,
Please correct me if I have misunderstanding:
1. You use static IP address to connect Windows 7 to Mac Mini
2. You can access Mac by typing file://ipaddress in Windows explorer
3. You try to click the Mac in Windows network, and you will get the error message ‘Windows cannot access
\\computername error code: 0x80070035 The network path was not found.’
Please take the following steps for troubleshooting:
1. Check if we can ping the computer name of the Mac Mini
2. Temporarily disable security software and firewall in case incorrect settings might block the connection.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support -
Need help with wifi on iPad 2 and to some extent iPhone 4
I have a few different wireless routers and no matter what I do or how I set them up, my wifi only iPad 2 has very erratic wifi speeds.
I see the same thing but to a lesser degree on my wife's and my iPhone 4 (2 of them).
I have a few year old Apple Airport Extreme and a brand new Cisco Linksys E3200.
The Airport extreme has very little options, but on the E3200 I have tried all the different wifi options (mixed, G only, N only which I can't even connect too) and using both or just one of the dual bands.
I am really at my wit's end here and two trips to the Apple store have yielded nothing. First genius said to wipe the iPad 2 and set it up as a new device and the 2nd genius said buy a new router (which is why I purchased the E3200).
Of course the apple store wifi it behaves flawlessly, but I suspect being an open network helps that...
Anyway, my internet service is uVerse and I get wired Speedtests in the neighborhood of 10-12 Mbps, but on the iPad it never goes above 6 Mbps down.
http://www.speedtest.net/result/1640909582.png - Wired
I have disabled QoS/WMM on the Linksys already...
Thanks in advanceNo solutions anyone?
I think I may have the same issues with my iPhone 4S running 5.0.1 too... -
Need some help with Slow Downs in Java3D and Servlets
Hi,
I realize that there is a separate forum for Java 3D, but I posted there, and did not get any response. This is kinda the crux of my program, so I would like to invite anybody on this forum with knowledge of Java 3D and servlets to give it a stab. Between this post and that one, there are TWENTY duke dollars up for grabs.
Thanks.
http://forum.java.sun.com/thread.jspa?threadID=603198Let me have an educated guess.
You calculated the time elapsed before sending in a server request - and at that point you have you updated timeLastStateChange yet, which means by the time of the next calculation of time elapsed this apparent delay is not counted in, hence the slow down in animation rate.
Hope this helps~
Alex Lam S.L. -
Help with importing PC photo files and then organizing it all in iPhoto
Hi everyone,
I'm relatively new to mac but I am just loving my purchase! I need some serious help with getting all of my photos organized though so I can easily find it for editing in iMovie.
I've accumulated over 10,000 photos stored on my PC which I've since transferred over to my LaCie external drive for my MacBook Pro via a wireless network connecting my PC & Mac. Some of these I've put onto my laptop internal hard drive and those I've imported into the iPhoto library. However, do I need to move the rest of the photos from my LaCie drive into my internal hard drive to import the photos into iPhoto, or can I tell iPhoto to look for the files in the external drive. If so, how do I do that? I know I'll then have to create albums in order to sort them, which I know how to do. Is there any fast way to do it by date? I had it sorted into different file folders by month & year so I could easily find them on my PC and would like to do the same using albums.
I am quickly running out of hard drive space on my laptop which is why I've put most of my photos on the external drive. Once I organize my existing collection, I would like to be able to import new pictures and have it stored on my external drive, not my internal drive. How do I do that?
Any other tips on organizing a massive photo library would be greatly appreciated.
Thanks,
KarenKaren,
Is there any fast way to do it by date? I had it sorted into different file folders by month & year so I could easily find them on my PC and would like to do the same using albums.
This is where you get to enjoy the power of iPhoto's database. You can change the Sort in the View menu. Check out View > Sort Photos > by Date.
Or, click the little calendar icon near the lower left corner of the iPhoto window. This allows you to filter the library by year, month, week, or date. You can Command-click to add another date to your filter. You can Option-click to choose a recurring date: you get that month or date for all years in your library. [Want to see your kid's birthday for every year? Just Option-Click that date. Cool.]
The keywords filter is similar. There is a preference setting where you choose to filter based on ALL keywords chosen (where by choosing more keywords you narrow your field) or ANY keyword (where the more keywords you choose, the larger your field will be). Click on a keyword to filter your library by all photos containing that keyword. Use Command-click to add more keywords to the filter. A difference is that Option-click will eliminate photos with that keyword from your filter. [You can find all pictures of your kids with your dog but NOT at Halloween.]
You can create Smart Albums to combine the use of dates, keywords, ratings, titles, comments and more. The more information you enter into the database, the more powerful the tools become.
When your task of importing is complete and you are ready to play with iPhoto's features it may help to look at the iPhoto multimedia tutorial. Better organized than trying to read through the Help files, it can help you get acquainted with many of iPhoto's features.
Have fun. -
Need help with Go Pro Hero 3 and Premiere Pro CS6
Hello,
I recently acquired PP CS6. I put my clip (30 seconds long) and I go to preview while editing, for the first 1.5 seconds it is fine but then it is very choppy. The audio is fine but the video does not play smoothly. When I save and process the video it is fine. It is frustrating to try to edit video this way. I'm sure I'm missing a step when creating the project but I haven't used Premiere Pro since CS6. This is only happening with Go Pro Hero 3 videos, any of my other cameras are fine. Any ideas? ThanksThere's a lot of confusion over how video encoding affects subsequent editing performance - a higher data rate has no direct relation to how much effort is required to decode and play the footage, in fact a higher data rate often makes playback easier - which is why transcoding to AVI can help with playback even though the files can be hundreds of times larger. Data rates with the same codec depend on the frame contents and recording quality, but for playback and editing what matters is the GOP (group-of-pictures) structure and the complexity of the encoding algorithm. Provided your disks are fast enough the data rate is immaterial to Premiere.
With long-GOP files (as typically created by consumer DSLRs and helmet cams) we have keyframes (I-frames) with a complete set of pixel data, then a series of intervening P- and B-frames which only store the difference between 'now' and 'one frame before' or 'one frame after'. Unless you're on an I-frame you have to calculate the chain of differences from the nearest I-frame, and when editing or applying an effect we must re-calculate the entire GOP, so Premiere has to hold a lot of data in the buffer. Remember all timelines in Premiere are internally transcoded to 32-bit floating point, so it's more work to 'play' the footage in the monitors than would be done by a simple playback-only application such as VLC, or in some other brands of NLE that only work in the footage's color space. Premiere's hardware acceleration (MPE) only kicks in once the buffer has been ingested, all the decoding of the original H.264 frames happens in your CPU.
With digital cinema cameras and some hacked DSLRs, we record "all-I" footage - so there's no GOP overhead and playback/editing is massively smoother. I can scrub all-I footage from a hacked 7D no problem on my relatively-ancient spare laptop, but the long-GOP files from a factory 7D struggle to play at all. Our all-I 7D footage can hit 300MBit/s compared to 35 for long-GOP. Helmet cams such as the GoPro do all they possibly can to squeeze data onto their storage cards, which means they have long-GOP codecs that have some of the most complicated compression algorithms out there. The Hero3's implementation of H.264 uses the Ambarella chip, whose files are very small but an utter nightmare to decode - hence far more of a demand on your CPU than an equivalent clip from a DSLR.
Jim Simon wrote:
Might be the 35 Mbps that is causing the choppy playback.
It shouldn't, assuming sufficient hardware. My GH2 clips often get up to over 90 Mb/s and play just fine on an older i7 920. -
Help with Flex based popup windows and data population.
Hello, I need a bit of help with Flex popups. I have a flex
application that uses a popup window when you click on a button and
displays information about the image above the button the user
clicked. I have about 4 images and I need to be able to display
information about each of them through the popup window when users
click on the buttons below the image.
At this time, I am trying to do this from somewhat of a
"static" point of view because I do not believe my hosting company
supports Flex Data services. You will find my code below.
First File.
<?xml version="1.0" encoding="utf-8"?>
<!--Application Initialization -->
<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
layout="absolute" width="850" height="750"
cornerRadius="10" borderColor="#000000"
backgroundGradientColors="[#1b3434, #000000]">
<!-- Popup-->
<mx:Script>
<![CDATA[
import mx.managers.PopUpManager;
[Bindable]
private var win:IMSAI;
private function init():void{}
private function createPopup():void{
win=IMSAI(PopUpManager.createPopUp(this,IMSAI,true));
win.title = 'IMSAI.Net';
win.x = -500;
win.y = 0;
customMove.end();
customMove.play();
]]>
</mx:Script>
<mx:Style>
TitleWindow {
borderStyle:solid;
borderThickness:2;
</mx:Style>
<mx:Parallel id="customMove" target="{win}">
<mx:Move duration="2000" xTo="{(stage.width - win.width)
/ 2}" yTo="{(stage.height - win.height) / 2}" />
<mx:WipeDown duration="2000" />
</mx:Parallel>
This is the code to trigger the popup when a user clicks on
the button. The code below is the code for the popup.
<?xml version="1.0" encoding="utf-8"?>
<mx:TitleWindow xmlns:mx="
http://www.adobe.com/2006/mxml"
layout="vertical" creationComplete="init()"
close="PopUpManager.removePopUp(this)"
showCloseButton="true" alpha=".8"
headerColors="[#000000,#1F3F62]" color="#FFFFFF"
minHeight="200" minWidth="300"
backgroundColor="#000000" title="IMSAI.net" width="520"
height="394" verticalAlign="middle" horizontalAlign="center">
<mx:Script>
<![CDATA[
import mx.managers.PopUpManager;
private function init():void{}
]]>
</mx:Script>
<mx:Canvas width="470" height="338">
<mx:Image x="10" y="10" width="140" height="103">
<mx:source>file:///C|/ColdFusion8/wwwroot/IMSAI/Web-App/Site_Images/IMSAI
Final Movie.swf</mx:source>
</mx:Image>
<mx:Text x="10" y="121" text="Description:" width="75"
height="25" fontWeight="bold" color="#ff0000"/>
<mx:Text x="158" y="10" text="Client:" width="52"
height="28" fontWeight="bold" color="#ff0000"/>
<mx:Text x="196" y="10" text="IMSAI Microcomputers
& Fischer-Freitas Company" width="252" height="39"/>
<mx:Text x="159" y="46" text="Industry:"
fontWeight="bold" color="#ff0000"/>
<mx:Text x="216" y="46" text="Computer &
Microcontroller Manufacturing." width="232" height="35"/>
<mx:Text x="83" y="121" text="IMSAI.net is the front-end
web application for IMSAI Computer " width="355"/>
<mx:Text x="10" y="136" text="manufacturing, customer
support, and order processing. Driven by a Microsoft database
back-end, this application includes rich flash forms, site search
capabilities, and flash content. Currently under phase II of a
three phase development plan, the e-commerce logic and processing
capabilities are under development. Once finished, this application
will be able to process orders provide customers with instant order
confirmation numbers, shipment dates, and payment processing."
width="428"/>
<mx:Text x="10" y="244" text="Technologies:"
fontWeight="bold" color="#ff0000"/>
<mx:Image x="100" y="244" width="50" height="50">
<mx:source>file:///C|/ColdFusion8/wwwroot/Sapphire
Development/content/cf8icon.jpg</mx:source>
</mx:Image>
<mx:Image x="244" y="244" width="50" height="50">
<mx:source>file:///C|/ColdFusion8/wwwroot/Sapphire
Development/content/flashlogo.jpg</mx:source>
</mx:Image>
<mx:Text x="53" y="290" text="Coldfusion 8 Enterprise"
height="30"/>
<mx:Text x="230" y="290" text="Adobe Flash 8"/>
</mx:Canvas>
What I want to do is either be able to create a popup file
for each button and photo, or find a way to pass a name like a
button ID that corresponds to a XML data structure and then
provides the appropriate data for the photo. I have tried altering
the first page of code with the "public" declaration to allow for a
second popup file for each button and image, but the IDE won't
allow me to do such because it creates errors stating I can only
have one public declaration of the kind and function above per
application. Help resolving this would be greatly appreciated.
Thank you.I have an idea of what I want to do. I am just having
difficulty articulating how to go about such. I know I want to find
a way so that if a user clicks on button 1, button 1 will send some
kind of variable. For example, a user clicks Btn1 under a picture.
Btn1 sends some kind of variable or binding to a data structure
which returns the picture's description, price, etc. and calls the
popup to display that data in a form like manner. Then the user
click Btn2 which does the same thing. The only purpose of the popup
is to display the data.
Do I create a data structure with a related name to say a
button name so when the btn is clicked, the a variable title btn1
will prepend itself to the data structure like
{btn1.imagename}
{btn1.price}
{btn1.description}.
I want each btn to call a different set of data about each
picture because right now, the code I have is allowing me multiple
buttons, but is just displays the popup. Is there a way to create a
separate popup window for each button? Thats seems as though it
would be easier. Thank you for your help. -
Help with queries about boot camp and partition, please.
Hi, I am hoping to partition my HDD. I have done this before, when I first got my macbook but got rid of it, and now I can't fully remember the do's and don'ts' of boot camp. I just need a few questions answered before I take any action.
1. I have a 120GB HDD with about 15GB free space. If I partition the drive will I lose any data on my existing HDD?
2. What is the minimal amount of space I can partition the drive and install Windows?
(I have a copy of Windows XP SP2, and really only need to install it for the use of one program that isn't available on the Apple operating systems.)
3. I tried using Parallels in which Windows took up about 6GB, will it be about the same again? I uninstalled it because I found it to lag a bit.
If you can help with any of these queries I would really appreciate it, thanks!Maybe you should first get a larger drive; you don't have much more than the minimum 10% free space that Mac OS needs.
Retry with Sun's VirtualBox. Maybe you just need more memory.
Lose data? Step #1: backup.
You may need to backup and erase your hard drive and then restore.
I'd invest in 300GB drive though. -
Help with converting hex to date and time
Hi!
I am using snmp4j libraries to walk the mib tree. The system date is getting returned in 11 hexadecimal octets. I require help in converting it to date and time. I looked up the RFC convention of what each octets represent. Require help with conversion.
Eg: 07:db:06:0a:29:1d:00:2b:05:1e
Thanks,Octets Contents Range
1-2 year 0..65536
3 month 1..12
4 day 1..31
5 hour 0..23
6 minutes 0..59
7 seconds 0..60
(use 60 for leap-second)
8 deci-seconds 0..9
9 direction from UTC '+' / '-'
10 hours from UTC 0..13
11 minutes from UTC 0..59
For example I just took the time an hour ago it came out as
07:db:06:13:12:11:1a:00:2b:05:1e
I have to convert this as a date long value to send it.
Do I have to write an utility of my own to do it?
Maybe you are looking for
-
Replacing all occurrences of characters in a string with one new character?
Hi there, I'm looking for a way that I could replace all occurrences of a set of specific characters with just one new character for each occurrence. For example if I have a string which is "word1...word2.......word3....word4............word5" how wo
-
I can't remember my icloud password
I Can't remember my icloud password .even birthday I can't remember because I used fake date .now I can't remember everything .how to login to my account ?
-
Error when updating Client Access Front End Service to Exchange 2013 Update 6
When updating to Exchange 2013 Update 6 we received the following error at the Step 11 of 13: Client Access role: Client Access Front End service step: Error: The following error was generated when "$error.Clear(); $fe = get-ActiveSyncVirtualDirecto
-
Change counrty in payment details
Hey, I need to update my payment details, but my new credit card is polish, while the previous was english. I can new number but not the whle details in payment.
-
Px4-300d, no gui access, stuck 95%, lost shares, unstable
Hello, i'm having a TON of issues with a px4-300d unit with 2x1tb drives: 1) with sw 4.0 (cant remmber the exact subversion) webgui stops responding after random days, but otherwise unit still is accesible 2) snapshots simply stopped working(generate