Help! Won't turn on, just happened over night.

My airport extreme has been working fine. Last night I used apple software update, only thing different then most nights. This morning I noticed the internet was down, went to the airport extreme and it won't turn on. No power, no light, no nothing. The surge protector it is plugged into has all the other attached gadgets working just fine.
Thanks for any suggestions on saving this.

It would be logical to check the power supply "brick" to see if it is delivering the 12 volts that it should be doing if it is working correctly. Radio Shack sells battery powered voltage testers for $10-12. Its a handy item to have around the house if you don't have one already.
If the power supply checks out OK, your best bet is going to take both the power supply and AirPort Extreme to an Apple store to let them have a look.

Similar Messages

Hi my ipod touch 8gb won't turn on just get the apple sign in middle of screen and my laptop also can't find my ipod wen i plug it in? any help would be greatly appreciated thank you.

hi my ipod touch 8gb won't turn on just get the apple sign in middle of screen and my laptop also can't find my ipod wen i plug it in? any help would be greatly appreciated thank you.

OR use this method
1. Press-hold the Home button (big circle below the screen)and the Sleep/Wake button (on top of the iPhone) simultaneously.
2. Continue holding both buttons (Ignore the"Slide to power off") until the iPhone shuts off and begins to restart.
3.You may let go when you see the silver Applelogo.
Thats all Folks!!

K7N2 Delta ILSR won't turn off, just restarts

K7N2 Delta ILSR won't turn off, just restarts. Every time I click on "Turn off computer" in Windows XP, it shuts down, but restarts again. Could this be OS related, or perhaps Bios related. My other machine, almost identical to this one, except that the other machine has BIOS rev 7.6 and this one 7.2.

PSUs seem to be yr favorite subject, but I'm afraid this time it's software. I experimented some more as the problem only occured after installing the Nvidia drivers. Comparing the system settings in the device manager before installing drivers and after installing them, reveils that the problem shows up when AGP HOST TO PCI BRIDGE is installed. When killing this item the PC shuts off properly. Unfortunately when turning back on, Windows automatically reinstalls the PCI bridge and I have the problem again. LOOKS LIKE A MSI SOFTWARE PROBLEM !
By the way I have a PCI graphics board and not AGP in the failing PC (the good one has AGP graphics).
Now what?
R.

My macbook pro 2010 model won't turn on. think its over heated. PLEASE HELP :(

I think my macbook pro 2010 model has over heated
My wife left it on a bean bag with the mains attached. when i picked it up it was very hot and now it won't turn on.You can hear the fan when you plug the mains in but it doesn't turn on. no lights or display.
Have taken it to an Apple repairer but they can find the problem. any help would be great Please help
Thank you

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
     If this does not help, contact Apple store.
     Genius Bar reservation:
     http://www.apple.com/retail/geniusbar/
     Best.

Phone won't turn on, just vibrates when plugged in

Last night, I plugged my phone in before bed. It showed on the battery icon that it was charging, and the red charge indicator light was on once the display turned off. However, by the time I woke up, the phone was dead, though still plugged in. I couldn't get it to do anything, so I tried an old battery that I had. Put the battery in, the phone turned on and showed a 47% charge. Knowing that battery was garbage (which is why I got a new one; I just held onto the old one for emergencies), I put the phone on the charger and the battery icon showed charging. Instantaneously, though (I'm not exaggerating, it was literally instant), the phone dropped to a 1% charge. I quickly tried to turn the phone off to see if I could even get even a little bit of an efficient charge out of it, and the phone started power cycling. I tried to stop it, but it turned itself off and on probably 20 times before it finally totally died (kind of reminded me of how sometimes an sick animal will go bat guano bonkers before it kicks it).
Now, when I try to plug the phone in it just pulse-vibrates every 2 or so seconds instead of showing that it's charging. It will continue to vibrate like that for a minute or two after I take it off the charger before it finally stops. Won't turn on in any mode, plugged in or not - I do get a flicker of the opening "Samsung Galaxy" screen before it shuts off and goes back to vibrating. I've tried to let it charge for 30-45 minutes, but no change. Taken the battery out, smacked it a few times, tried to charge with my computer, tried different cables/chargers, nothing helps. I have no idea if either battery has any charge at all at this point (though I suspect not). I haven't damaged my phone at all - no recent/significant drops, no water - but of course I'm just barely barely out of warranty. Am I toast or is there some way to fix this?

Thanks for your reply.
Unfortunately, since (as I clearly noted in my original question) my phone will not turn on, I can't confirm the phone software, though I've downloaded any and all updates that I've been notified of. I have no idea if any apps updated immediately prior to the issue happening; it's likely that some update to something downloaded not long before the problem started since I plugged in the phone shortly after I got home for the evening and reconnected to my home WiFi, but I wouldn't have any way to tell you what it might be. My phone will not boot in safe or recovery mode either, if that helps answer if an app is causing the issue.
I tried to take it to a Verizon store; they told me that they had literally NEVER heard of my issue before and so wouldn't be able to fix it and didn't even attempt to help, just tried to sell me a new phone, so that wasn't super helpful. Since I had zero problems up to this point with my phone, and because I'm now not eligible for the early upgrade to the Edge program without the early termination fee because I don't have a working phone, it sure would be great to fix the one I have. If anyone else has any advice, I'd appreciate it!

I can't see the bar which contains play, stop button on Youtube. Help me!!! Just happen with firefox and chrome after install DivX and I had removed DivX.

I had installed DivX and it includes DivX Web player but, when i remove it, the problem happend. When I click on a video, the bar which contains play, stop... buttons is there. But when the video nearly play, it disapears. The problem just happen with Firefox and Chrome, but it doesn't mean with IE. Help me plz, I hate using IE just love FF but the problem prevent me from watching video on youtbe which is very terrible with me.

This is my problem, see the picture.

My 4th gen iPod won't turn on, just plays the shutting down screen forever

I have a 4th gen ipod, 8gb, and it hasn't really given me problems until the past few days, it's been crashing constantly and freezing. Now it has shut down and when I turn it on it is just stuck on the shutting down screen. I've tried holding down home and power, it shuts off, then just turns right back on and does the same thing. I drained the battery, and it showed the normal screen for being dead, then when I plug it in, it starts up with the shut down screen again. Something similar happened to one of my friends so she just wrote it off as being "completely dead" and gave up. (But I don't want to just give it up because basically my only pictures of my cat that passed away are on it, and I don't have iCloud) Also, I thought maybe it was because my version was 5.1.1, I never updated because I didn't want the youtube app to be gone. Is there anything left I can try or is it completely done for?

I had the exact same problem with my ipod and the way i got out of it was i connected it to my pc - mac works too.- then when it turn on i held only the power button for about 10-60 seconds until it finally shutoff then i basically put it in dfu mode ( if you don't already know what it is and how to do it i will explain that after) and my pc recconized it in dfu mode and after waiting about 5 min unplug from your pc or mac and if it doesnt already show the power screen on then turn it on and it should work if it just goes to recovery mode then repeat the steps for putting it in dfu mode just without pluging it in.
Here's how to put it in DFU mode. First just hold the power and home screen botton for 10 seconds or until you see it flash. Next you let go of the HOME BOTTON ONLY while still holding the power botton down for a good 20-25 seconds then you can let go and your done! *Note: if you have it plug in to a pc or mac you will also see something saying your pc/mac is recognizing your ipod in DFU mode.
Hope it helps with your problem! （＾∇＾）

Ipod touch won't turn on, just shows the apple logo - even when plugged into Itunes?

I have an Ipod touch 8GB - it's virtually never been used. I have tried to charge it up but nothing happens - it just displays an apple logo. I have plugged it into Itunes but again nothing happens. Any ideas?
Thanks K.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

X6 won't turn on just vibrates

My x6 wont turn on and just vibrates. I have tried the 4 finger reset but just does the same. Any help would be great.

Boldie wrote:
Yes I was trying to do a system software update but the phone wouldn't turn back on.
I reckon the phone suffered from a failed update rendering it unusable. I suggest sending the phone to a Nokia Care Centre in your area. They will fix it with no charge if the phone is still within warranty.

Dual 1.25Ghz won't boot? Just happened!?

Hello, and thanks in advance for any feedback.
I have a Dual 1.25Ghz G4 with 4 HDs in it. I had it running earlier this morning and decided to pull the smaller (and older drive). I turned it off, unplugged everything, and pulled the drive. I closed the case and now it doesn't boot. I press the button and it lights up, but nothing happens. No powerup up, no power supply noise.. nothing.
So, thinking there was a slight chance my OS, or something, was on that older drive, I reinstalled it. Same thing.
What could have damaged upon opening the case?
Thanks for your help!
Justin

Hello! I'm assuming that the drives are jumpered correctly? Anytime you remove or add hardware you may have to reset the PMU. Press the button once with ALL external cables unhooked and then reconnect and restart. Tom
Below is an example of the pmu button
[IMG]http://img49.imageshack.us/img49/3729/fw800logicbd4xu.jpg[/IMG]
[IMG]http://img470.imageshack.us/img470/1623/mddlogicbd4ga.jpg[/IMG]

My screen won't turn on - just blank with Apple logo and rotating little gear thing

I unplugged my computer abruptly during a big storm and didn't log off or shut it down first. Now when I turn the MAC on all I get is a blank screen with the apple logo. I have tried a couple of fixes from the book like holding down option key but nothing is working. I called support and the young woman just read the same stuff from the manual.....I can't get a store appt. until Friday! (And I have protection plus which right now is seeming like a waste)

Hi.
Power off the computer by pressing and holding the power button... takes about 10 seconds.
Reboot, and right after you hear the startup chime, press and hold the Option key. Are you presented with a screen that shows the startup ard disk and OS X version?
If so, click it and press <enter>.
Does your iMac boot up properly?
If not, power it off again as above.
Reset the SMC
• power off
• disconnect both ends of the power cable
• wait 30 seconds - min.
• plug in the power cable - wait 5 seconds min.
Reboot. Any change?

IPhone 4s won't turn of just reboots unless it is charging anyone else have this problem

Recently I tried to turn off my iPhone 4s because I was in a meeting and I noticed that it just rebooted, so I tried again and again and it just kept rebooting and wouldn't turn off. The only way it will turn off is if I have it charging then it will shut off. Is this normal?

I'm having the same issue.... Any update on this?

HT204370 Purchased and downloaded 5 different movies. Now I cannot run them on the computer that I downloaded them to.( Ipad stills has them) They are not able to locate. This has just happened and I would like to have them on my desktop computer. Any hel

5 Different movies have been deleted from my Itunes account. They have been purchased and downloaded to my Ipad. I cannot watch them on my desktop that I used to download them in the first place. This has just happened over the last week. How can I RE-download them back to my desktop computer. I will need them for my new Ipad3.

Hello gpbondi,
The following article provdies step-by-step instructions for downloading your purchases both in iTunes and on your devices.
Download past purchases
http://support.apple.com/kb/HT2519
Cheers,
Allen

Eos-m LCD screen won't turn on

The camera works, allows me to take photos, however the lcd won't turn On just stays black. So i have no view of what I'm taking photos off. The touch sensor works as it makes the usual noises and allows me to take photos touching. Any idea why the screen is getting no image at all, not even menu? Thanks!

Will any buttons activate the rear LCD screen (for any purpose)? e.g. can you press either the "Menu" button or the "Info" button and get a display?
On EOS DSLRs the "Info" button cycles through several choices to display on the rear LCD and one of the choices is to just have it off -- but that's because regular DSLRs have a viewfinder. The button simply keeps looping through the choices.
But on the EOS-M there is no viewfinder and I didn't think there was an option to disable the LCD when the camera is on.
Tim Campbell
5D II, 5D III, 60Da

Just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now

just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now

I am assuming the phone was working prior to you installing IOS 6? Did you use itunes to install IOS 6 or just run from the phone?
When I tried to do the Over The Air update to IOS6 on my iPhone 4, it errored out and I had to connect it to iTunes and select "Restore" from the summary screen after iTunes finds the phone is connected. If this works for you, it will go through a couple of reboots that take a few minutes to complete. It should then give you the option to start with a fresh new phone or to use one of your previous backups to load your contacts and other information, provided you have backed up the phone previously.
I hope this helps you my friend!

Help! Won't turn on, just happened over night.

Similar Messages

Maybe you are looking for