Hey I own hp dv6 3043 tx and am facing error 301 on boot up ..and later it does not start...pl help?

I bought a dv6 3043 tx in 2010.. For about 1 and half years it worked fine but a few days bak .its performance went down...few days later it showed up with error301 at boot up when I clicked continue to boot up...it fails to boot and started over again ... A Pl, help me cause this has caused a barrier in my work...

Hi,
Your notebook does not have Two  HDD bays available.
The drive on the link below is an example of one that would be fine for your notebook.
500Gb Hard Drive
The procedure to replace the Hard Drive starts on Page 55 of your Maintenance & Service Guide.
Once done, simply use your Recovery DVDs to reinstall the Operating System on the new drive.
If you don't have your Recovery Discs, you can order a replacement set using the link below.
http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c00810334&cc=us&lc=en&dlc=en
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Similar Messages

  • Just installed Firefox 3.6. Firefox will not start and Firefox safemode does not start either. Using Task manager I do not see if started either. If I create a new profile and start from that window, Firefox starts up. I see no error windows/messages. I d

    Just installed Firefox 3.6. Firefox will not start and Firefox safemode does not start either. Using Task manager I do not see if started either. If I create a new profile and start from that window, Firefox starts up. I see no error windows/messages. I do have it listed in my Firewall as an exception program with Permit All. What is happening?
    == This happened ==
    Every time Firefox opened
    == After removing Firefox and Reinstalling it. ==
    == User Agent ==
    Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; GTB6.4; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.04506.30; .NET CLR 3.0.04506.648; MS-RTC LM 8)

    If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
    See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox
    See also [[Basic Troubleshooting|#Make_a_new_profile|Basic Troubleshooting: Make a new profile]]

  • Oracle service, Listener and http server does not start automatically

    Hello,
    I have Oracle 9i release 2 installed on Unix HP box if system restart in case of power failure the Oracle service, Listener and http server does not start automatically, is there any ready reference available to check what's wrong is happening(I don't have knowledge of Unix).
    Thanks, Khawar.

    Hi Rajesh,
    Thanks for reply, I will check this link and will be back if facing problem.
    Regards, Khawar.

  • I go through the process of burning a DVD from a Premier Pro Project and at the end of the process I get an encoding error and the dvd does not start burning.  How do I fix this?

    I go through the process of burning a DVD from a Premier Pro Project and at the end of the process I get an encoding error and the dvd does not start burning.  How do I fix this?

    adam@honestmusky wrote:
    Yes I am using encore.  I used to have no problem doing this, but I had to get a new computer and now something isn't working right.
    How about some DETAILS?
    -Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840
    Also describe the EXACT steps you take to go from Premiere Pro to Encore

  • I Have a folder with an interrogation mark blinking and the computer does not start. Anybody?, I Have a folder with an interrogation mark blinking and the computer does not start. Anybody?

    I Have a folder with an interrogation mark blinking and the computer does not start. Anybody?, I Have a folder with an interrogation mark blinking and the computer does not start. Anybody?

    Here is some information and troubleshooting steps from Apple:
    http://support.apple.com/kb/TS1440

  • Hi there, when i press the start button on my G4 twin processor, the light inside the button comes on until I let go when it goes back off and the machine does not start up. Any ideas?

    Hi there, when i press the start button on my G4 twin processor, the light inside the button comes on until I let go when it goes back off and the machine does not start up. Any ideas?

    Sounds a bit like the Power Supply, but...
    If you don't know the model, find the Serial# & use it on one of these sites, but don't post the Serial# here...
    http://www.chipmunk.nl/klantenservice/applemodel.html
    http://www.appleserialnumberinfo.com/Desktop/index.php
    How to find the serial number of your Apple hardware product...
    http://support.apple.com/kb/HT1349
    How to reset the SMU/PMU on a Power Mac earlier G3, G4, G5 models...
    http://support.apple.com/kb/HT1939

  • Hello...I´ve just updated my Iphone 4 with 5.1.1. and my Iphone does not start at all....Nothing... Help pls

    Hello...I´ve just updated my Iphone 4 with 5.1.1. and my Iphone does not start at all....Nothing... Help pls

    Have you tried a reset by pressing and holding the sleep/wake button and the home button for 10-15 seconds until the Apple logo appears, ignore the red slider.  Then turn back on. You won't lose any data doing the reset.

  • Listener (and database instance) does not starts up automatically: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor

    Hi at all.... I'm a newbie with database oracle.,
    I have the follow problem:
    I installed Oracle Database 11g R2 XE on my guest operating system CentOS 6.5.
    I have changed  the hostname in my SO CentOS (where is installed oracle 11g R2 XE) after installation was completed successfully.
    -) Before and during installation the hostname was localhost.
    -) After installation I changed the hostname in VMCentOS
    From the moment I changed the hostname, nothing starts up automatically. In particular, the listener and the database instance does not starts up automatically.
    When I starts up the listener manually and I try to connect to database instance with SQLPLUS i get this error:
    ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
    I think that the problem is due to the changed hostname because I, for testing and debugging purpose, re-installed a new OS CentOS virtual machine, re-installed oracle database 11g and  I have not got that problem. The database instance and the listener starts up automatically!
    Can any one tell me if maybe the problem is related to the hostname changed? ... and Why?
    P.S.: After changed the hostname I have also modified the listener.ora and the tnsnames.ora by modifying the HOST with the correct hostname.

    -) Output of command chkconfig (there isn't any line oracle-xe 0:off   1:off  2:on  3:on  4:on  5:on  6:off):
    [oracle@VMCentOS /]$ chkconfig
    NetworkManager     0:off    1:off    2:on    3:on    4:on    5:on    6:off
    abrt-ccpp          0:off    1:off    2:off    3:on    4:off    5:on    6:off
    abrtd              0:off    1:off    2:off    3:on    4:off    5:on    6:off
    acpid              0:off    1:off    2:on    3:on    4:on    5:on    6:off
    atd                0:off    1:off    2:off    3:on    4:on    5:on    6:off
    auditd             0:off    1:off    2:on    3:on    4:on    5:on    6:off
    blk-availability    0:off    1:on    2:on    3:on    4:on    5:on    6:off
    bluetooth          0:off    1:off    2:off    3:on    4:on    5:on    6:off
    cpuspeed           0:off    1:on    2:on    3:on    4:on    5:on    6:off
    crond              0:off    1:off    2:on    3:on    4:on    5:on    6:off
    cups               0:off    1:off    2:on    3:on    4:on    5:on    6:off
    dnsmasq            0:off    1:off    2:off    3:off    4:off    5:off    6:off
    firstboot          0:off    1:off    2:off    3:on    4:off    5:on    6:off
    haldaemon          0:off    1:off    2:off    3:on    4:on    5:on    6:off
    htcacheclean       0:off    1:off    2:off    3:off    4:off    5:off    6:off
    httpd              0:off    1:off    2:off    3:off    4:off    5:off    6:off
    ip6tables          0:off    1:off    2:on    3:on    4:on    5:on    6:off
    iptables           0:off    1:off    2:on    3:on    4:on    5:on    6:off
    irqbalance         0:off    1:off    2:off    3:on    4:on    5:on    6:off
    jexec              0:off    1:on    2:on    3:on    4:on    5:on    6:off
    kdump              0:off    1:off    2:off    3:on    4:on    5:on    6:off
    lvm2-monitor       0:off    1:on    2:on    3:on    4:on    5:on    6:off
    mdmonitor          0:off    1:off    2:on    3:on    4:on    5:on    6:off
    messagebus         0:off    1:off    2:on    3:on    4:on    5:on    6:off
    netconsole         0:off    1:off    2:off    3:off    4:off    5:off    6:off
    netfs              0:off    1:off    2:off    3:on    4:on    5:on    6:off
    network            0:off    1:off    2:on    3:on    4:on    5:on    6:off
    ntpd               0:off    1:off    2:off    3:off    4:off    5:off    6:off
    ntpdate            0:off    1:off    2:off    3:off    4:off    5:off    6:off
    portreserve        0:off    1:off    2:on    3:on    4:on    5:on    6:off
    postfix            0:off    1:off    2:on    3:on    4:on    5:on    6:off
    psacct             0:off    1:off    2:off    3:off    4:off    5:off    6:off
    quota_nld          0:off    1:off    2:off    3:off    4:off    5:off    6:off
    rdisc              0:off    1:off    2:off    3:off    4:off    5:off    6:off
    restorecond        0:off    1:off    2:off    3:off    4:off    5:off    6:off
    rngd               0:off    1:off    2:off    3:off    4:off    5:off    6:off
    rsyslog            0:off    1:off    2:on    3:on    4:on    5:on    6:off
    saslauthd          0:off    1:off    2:off    3:off    4:off    5:off    6:off
    smartd             0:off    1:off    2:off    3:off    4:off    5:off    6:off
    snmpd              0:off    1:off    2:off    3:off    4:off    5:off    6:off
    snmptrapd          0:off    1:off    2:off    3:off    4:off    5:off    6:off
    spice-vdagentd     0:off    1:off    2:off    3:off    4:off    5:on    6:off
    sshd               0:off    1:off    2:on    3:on    4:on    5:on    6:off
    sysstat            0:off    1:on    2:on    3:on    4:on    5:on    6:off
    udev-post          0:off    1:on    2:on    3:on    4:on    5:on    6:off
    vmware-tools       0:off    1:off    2:on    3:on    4:on    5:on    6:off
    vmware-tools-thinprint    0:off    1:off    2:on    3:on    4:on    5:on    6:off
    wdaemon            0:off    1:off    2:off    3:off    4:off    5:off    6:off
    winbind            0:off    1:off    2:off    3:off    4:off    5:off    6:off
    wpa_supplicant     0:off    1:off    2:off    3:off    4:off    5:off    6:off
    [oracle@VMCentOS /]$
    Moreover in /etc/sysconfig there isn't any file oracle-xe!!!
    At this point, I suspect that something in the installation I mistook.

  • HT1338 For the past 2 weeks I have not been able to open any small video on the yahoo page or face book. I get  Blocked Plug In. I have installed Adobe and that still does not work. Help.

    For the past 2 weeks I have not been able to open any small video on facebook or on the yahoo page . I have installed Adobe and it still dies not work. Help.

    Use "Firefox/File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit") to close Firefox if you are currently doing that by clicking the close X on the title bar.
    See "Hang at exit":
    *http://kb.mozillazine.org/Firefox_hangs
    See "Firefox hangs when you quit it":
    *https://support.mozilla.org/kb/Firefox+hangs

  • MacBook Pro can turn on and off, but does not start up. Stays on white screen with flashing folder icon, does not go to desktop.

    MacBook Pro is not starting up. It just stays on a white screen with a flashing folder icon. Have tried restarting while holding the Option key, and the cursor becomes visible and movable, but it does not go to the desktop.

    Hello Sonya_Rose,
    I found this article when researching the issue you describe here named A flashing question mark appears when you start your Mac found http://support.apple.com/kb/ts1440.
    Check the mouse and keyboard
    This issue might occur if a mouse or trackpad button is pressed during startup. Make sure the button isn't pressed.
    If the issue persists, shut down your Mac with its power button, disconnect any external mouse and keyboard, then turn on your Mac with its power button. If the flashing question mark issue persists, reconnect the keyboard and mouse.
    Additional steps
    If your Mac still starts to a flashing question mark, follow the steps below. If any step resolves the issue, you don't need to continue to the next one.
    Select your Mac OS X startup disk with Startup Manager by restarting and holding the Option key. After your Mac starts up, restart again to verify that the flashing question mark does not appear.
    If the issue persists, insert your Mac OS X installation disc. Be sure to either use the disc that came with your Mac, or, if you installed a later Mac OS X version from disc, use the newer disc.
    MacBook Air note: On a MacBook Air, there are two options for starting up from Mac OS X media: Either connect a MacBook Air SuperDrive to the MacBook Air via the USB port and restart the computer, holding down the C key during startup, or use Remote Install Mac OS X to startup from a system software DVD that's located on a partner computer. Once started up from Mac OS X media, skip to step 3.
    Restart the computer, then hold the C key during startup.
    From the Utilities menu, choose Disk Utility. Don't click Continue.
    Select your Mac OS X disk (named "Macintosh HD" by default) in the left side of the Disk Utility window.
    Click the First Aid tab.
    Click Repair Disk to verify and repair any issues with your Mac OS X startup disk.
    After repairing the disk, try to start up normally.
    Important: If Disk Utility finds issues it cannot repair, you may need to back up as much of your data as possible (or use Time Machine to back up to a different disk), then erase the disk and reinstall Mac OS X. You should back up important files and data before erasing a drive. Erasing deletes everything on the hard disk (including things on your desktop). Also, you can install Mac OS X onto an external disk, start from the external disk, and use Migration Assistant to transfer items from your usual internal Mac OS X startup disk to the external disk, then erase the internal disk and reinstall Mac OS X.
    If the issue persists, and Disk Utility didn't find any irreparable issues, quit Disk Utility, quit the Installer, select your disk when prompted, and restart.
    If the issue continues, reset PRAM. Note: After resetting PRAM, if the computer starts up normally, reselect the startup disk in the Startup Disk preferences.
    If none of these steps resolve the issue, start up from the Mac OS X Installation disc and reinstall Mac OS X.
    Regards,
    Sterling

  • InDesign CS5 and 5.5 does not start

    I have to support a lot of different users with CS3, CS4, CS5 and CS5.5. Now I set up all this product on a brand new Mac, OSX 10.9.2 Retina, but they do not start properly (nothing happens). What is the problem?

    Well, I copied my previous Mac (Mavericks), where I  have them all running parallell. None started. Then I uninstalled and reinstalled 5.5. Did not start! When I double click the icon nothing happens! No message, no log.

  • Was advised to delete system configuration file from hard drive and now computer will not start - any help would be appreciated.

    Downloaded Yosemite and since then cannot connect to internet or bluetooth mouse - was advised to delete system configuration file from the hard drive and since then cannot start up computer. Any help would be appreciated - cheers.

    Boot the MBP with the OPTION+COMMAND+R keys down.  The result should be a display showing a revolving globe.  By following the instructions, you will be able to reinstall the original OSX.  Then you may reinstall Yosemite.
    A solid Internet connection will be required.
    Ciao.

  • I have a Mac Air.  When I go to view any video online (youtube for example)and click on a video, I get the space where the video should play but there is just a black screen and no play button and the video does not start.  Any ideas?

    I have a Mac Air. When I go to view  video online (youtube for example), the screen for the video comes up with a black square space where the video should play.  But there is no pay button and the vidoe never starts playing.  Any suggestions would be appreciated.

    Shockwave and Flash are not the same. Try installing a Flash plug-in. Here's the latest: Adobe Flash Player 11.2.202.183

  • HT1414 i wanted to reset my iphone from the phone settings and i started with no problem but now my i phone got stuck i can only see the apple logo  and my phone does not start what to do please help

    i wanted to reset my iphone 4 from the phone settings and everything started okay until i realised it was not working at all now my phone is tuck with the apple logo and won't start can not connect to the itunes store as well what to do please help

    Place your iPhone into recovery mode as described here.  You may have to try to enter recovery mode more than once to succeed.
    http://support.apple.com/kb/HT1808

  • The Leno s696 phone stays frozen on the logo of Baidu cloud and the desktop does not start‏

     I pressed the power button normally begin until the logo of Baidu Cloud and is frozen here the LEDs flash green, red and blue. does nothing more and stays frozen there.
    I have asked this is because, I was told that it has been for software failure and that is solved by reinstalling the software. is this true? 

    Yep, done all that.  Repeatly.  Don't get any sort of recovery mode message or the phone showing up on iTunes at all.  iTunes is most current version, all diagnostics show everything fine, and it works fine with my current phone.  Just....nothing.

Maybe you are looking for