Hhub2 router stats

Where on the Hh2 do you find the router stats ?
Ta,
djh22

djh22 wrote:
I've  just moved to BT and I was wondering what the stats were on the hhub2 compared to my Netgear 834g and strangely there is a difference in downstream connection, Netgear reports 8034 and Hhub2 reports 7127.
I have a dect phone connected to the Hhub2 I wonder if it accounts for the difference.
My Netgear always sync'd at a higher speed that the HHub which is why I threw the HHub away.  Netgear will give you better control over port forwarding etc. 
The important speeds are not the sync speeds which always show higher than reality (maybe that's why they show them in the hub) the important one is the IP profile which is the max that your connection will handle and can only be found at http://speedtester.bt.com
BW 10 days is a myth to keep you out of the helpdesk's hair. It all happens in the first two or three days once connected.
..... Jarviser's Home Hub Index

Similar Messages

  • Route statements in ASA

    If your inside interface has an IP address of  x.110.215.17 and you have the following route statement.
    route inside x.110.208.0 255.255.255.0 x.110.215.17
    route inside x.110.209.0 255.255.255.0 x.110.215.17
    route inside x.110.210.0 255.255.255.0 x.110.215.17
    I'm assuming this means that anything coming into the ASA for the networks listed, will be routed to the
    inside interface via x.110.215.17?
    Note that the inside interface and the next hop on the route statements are the same.

    I should have been more technically correct in my last update.  The ARP request has nothing to do with the 10.10.10.0/24 IP range but rather, the layer 2 VLAN associated with the inside interface behind the device.  By adding the route statement pointing to the inside interface, the ASA will broadcast an ARP request to all the hosts within the VLAN.
    So,
    Ethernet0/1              inside                 10.10.10.1      255.255.255.0   manual
    route inside 10.10.20.0 255.255.255.0 10.10.10.1
    -A request is made for 10.10.20.20, the ASA will generate something similar to the following:
    arp-req: generating request for 10.10.20.20 at interface inside
    arp-send: arp request built from 10.10.10.1 0015.46e7.8d55 for 10.10.20.20 at 53392994170

  • Network address as the next hop address in ip route statement???

    Hi All,
    I am confused about ip route statements in the following Cisco document.
    Configuring ISDN DDR with Dialer Profiles
    Document ID: 9568
    http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
    The statements are;
    ip route 172.22.0.0 255.255.0.0 172.22.80.0
    ip route 172.22.80.0 255.255.255.0 Dialer1
    Why does it use network address as next hop address on the first line?
    And it is a source network address on the second line.
    Please suggest me.
    Thanks a lot,
    Nitass

    When you specify a network address as next hop in a ip route statement, the router does recursive lookup. When it matches a packet for a network other than 172.22.80.0, it will match the router 172.22.0.0 and the route basically says use 172.22.80.0 as the next hop. Now the router looks up the routing table for how to reach 172.22.80.0 and ends up routing via Dialer 1.

  • Exactly how do I post router stats

    Please be patient with this total "numpty", but exactly how does one cut and paste router stats. I get error message to the effect that "invalid HTML content has been removed...etc" Sorry if this request is in wrong place, but I've done a search and can't find anything. Thanks.
    JohnF
    “Dogs come when they're called; cats take a message and get back to you later.”
    Mary Bly
    Solved!
    Go to Solution.

    Thanks, much obliged.  I was getting in an awful mess cutting and pasting in MS Word and trying to get rid of cells etc. to no avail.
    Regards
    John F
    “Dogs come when they're called; cats take a message and get back to you later.”
    Mary Bly

  • Acceptable ranges for router stats

    There are many queries posted here about line speed which result in repliers asking the questioner to post their router stats.
    Two of the main figures that always seem to be mentioned are the Line Attenuation and Noise Margin.
    Is there anywhere that gives an acceptable range for these figures and a simple explanation of what affects them?
    Same for any other useful stat figures e.g. values given by BT speedtester.
    Cheers
    John

    http://kitz.co.uk/adsl/linestats.htm

  • Broadband speed & router stats

    I'm hoping someone will be able to comment on the download speeds I'm getting for my broadband (BT opt 1).
    According to the BT checker, I should be able to get up to 6Mb, and I'm fairly close to the exchange (700m). My router stats look like this:
    ADSL Link
    Downstream
    Upstream
    Connection Speed
    2272 kbps
    288 kbps
    Line Attenuation
    25 db
    7 db
    Noise Margin
    26 db
    30 db
    After a lot of tidying up of the internal phone wiring these are now fairly consistent whether I'm plugged in to the master socket or one of the extensions. These were taken from the router fairly soon after rebooting it earlier.
    My question is whether the 2Mb downstream I'm getting seems reasonable, or could I be expecting more than that? And is it possible that the 2Mb is being imposed as a limit, rather than being the maximum speed?
    Any thoughts and comments gratefully received.

    If you are that close to the exchange, there must be something wrong with your line, it takes a circuitous route to get to you, or you are on a 2Mbit package still. I am approximately 3/4km (750m) from my exchange, and get the following:
    Speed: 8126 down, 440 up
    Att: 18.5 down, 8.5 up
    SNR: 19.5 down, 32.5 up
    Although, the 7db up attenuation you are getting suggests that is the limit that your line can support, rather than you being on a 2Mbit capped connection.

  • IP SLA Default Route state down to much

    Hello,
    I am attempting to use IP SLA trackers to dynamically set the default route going out over a DSL connection.  if the sla trackers are down the default route learned from the WAN will take over, but normally we want to send internet/default route bound traffic out over the DSL connection.  
    ip route 208.67.220.220 255.255.255.255 1.2.3.4
    ip route 208.67.222.222 255.255.255.255 1.2.3.4
    ip route 0.0.0.0 0.0.0.0 1.2.3.4 track 3
    track 1 ip sla 1
     delay down 60 up 60
    track 2 ip sla 2
     delay down 60 up 60
    track 3 list boolean or
     object 1
     object 2
    ip sla 1
     icmp-echo 208.67.222.222 source-ip 1.2.3.5
     threshold 1000
     frequency 10
    ip sla schedule 1 life forever start-time now
    ip sla 2
     icmp-echo 208.67.220.220 source-ip 1.2.3.5
     threshold 1000
     frequency 10
    ip sla schedule 2 life forever start-time now
    the issue we are having is if the SLA threshold is breached, it immediately sends the trackers into a delay down state.  the tracker delays down for 60 seconds, then very quickly comes back up.  What we want to accomplish is only if the sla tracker has breached the threshold or is down for 60 seconds, then put the tracker into a down state.
    Thanks.

    The configuration seems to be correct: IP SLA change as soon as the icmp fail but the tracker delay should ensure the it changes its state after 60seconds of icmp failure. Do you experience a different behaviour ?
    What I'm worried about is that, after the default router through the WAN is in routing table,  the ip sla ping will be successful and therefore the static route 
    ip route 0.0.0.0 0.0.0.0 71.32.39.46 track 3
    will be used but, at that point, which is the path to 71.32.39.46 ? 
    Another thing is that, in case of DSL link failure, this configuration will not automatically revert to WAN link because 71.32.39.46 will be still up and running, isn't it ?
    Let me know,
    enrico

  • Router stats?

    Recently moved my router downstairs due to building work and router speed is very very slowthese are my stats System Up Time: 74:16:36PortStatusTxPktsRxPktsCollision PktsTx b/sRx b/sUp TimeWANMER1387159820103413083001227490574:15:17LANUp99433774273306757184074:16:36WLANUp1960284513453293924392728934474:16:13Broadband LinkDownstreamUpstreamConnection Speed20000 kbps3690 kbpsLine Attenuation24.6 dB0.0 dBNoise Margin7.8 dB6.6 dB

    According to those stats, you are getting 20Mbps downstream and about 3.7 upstream.
    What speeds are you getting and how are you measuring them?
    Try performing a speedtest using www.speedtest.net with a wired connection to the Sky Hub and see what it says.

  • My Router Stats Show My Wife's Computer As Mine!?

    I have a G3 iMac connected by ethernet cable to my router and an Intel iMac connected wirelessly.
    My router has always shown them both as "ian-browns-imac", which was perfectly correct.
    However, I have just completely erased the G3 and installed the OS afresh using just my wife's details.
    To my surprise, instead of seeing "jacqui-browns-imac", it still appears as "ian-browns-imac".
    Can anyone explain this weird state of affairs?

    What do you mean by that?
    As mentioned I have switched off and restarted the router.
    Incidentally this is how I have my sharing windows configured for both iMacs.

  • Anyone please explain these two router stats.

    Having a (hopefully) minor glitch at the moment with what seems like a stuck IP profile, main thread here.
    A couple of other questions though.
     http://community.bt.com/t5/BB-in-Home/How-often-do-BT-reset-the-HH-remotely-and-should-it-effect-IP/...
    In the advanced stats are two connection times.
    1. Internet connection time and ADSL connection time.
        I was under the impression ADSL time is the time the hub has been on since the last reset... either by BT or by me pulling the plug. That was showing 6 days... I suspect my problems started when the HH was remotely reset. Am I correct in what this time measures ?
    2. I see there is also an "Internet connection" time... what's that ?
        It shows 1 day 14 hours. What is this figure measuring and what is it's significance ?     
    thanks

    This seems to be a common issue on this forum.
    Please take a look at this if you're trying to install via
    Terminal Services:
    http://support.microsoft.com/default.aspx?scid=kb;en-us;320185

  • Recent bRAS Profile Change - Router Stats

    Hai!
    Recently, my IP profile has been dropping consistently. I was on 3000 bRAS profile not too long ago (I think I had 5000+ sync in the test socket once).
    Since this Edinburgh outage, my profile has been dropping every few days with no disconnections. I decided to put the hub in my test socket last night and let the hub settle overnight before I posted the results here. My sync has gone up, but I don't understand the noise margin etc... Can any techie types give me any clues as to what may be wrong with my connection? Are these current stats OK in the test socket, which would point towards my internal wiring being at fault? Are these current stats showing a problem with my connection in the test socket, which would point towards an external fault?
    Any help would be greatly appreciated. Thanks in advance.
    Connection information
    Line state
    Connected
    Connection time
    0 days, 11:17:49
    Downstream
    2,944 Kbps
    Upstream
    448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.1
    Latency type
    Fast
    Noise margin (Down/Up)
    15.8 dB / 19.0 dB
    Line attenuation (Down/Up)
    47.0 dB / 27.0 dB
    Output power (Down/Up)
    18.1 dBm / 11.9 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    0 / 0
    CRC Errors (Down/Up)
    107 / 2147480000
    HEC Errors (Down/Up)
    nil / 1
    Error Seconds (Local)
    93

    Here are my speedtest.bt.com results. My IP profile still hasn't gone up since last night. I understand it can take up to 72 hours to reconfigure:
    1. Best Effort Test:  -provides background information.
    Download  Speed
    675 Kbps
    0 Kbps
    1000 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 675 Kbps
     For your connection, the acceptable range of speeds is 200-1000 Kbps.
     Additional Information:
     Your DSL Connection Rate :2944 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 750 Kbps
    2. Assured Rate Test:  -provides background information.
    Download Speed
    116 Kbps
    0 Kbps
    600 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 116 Kbps
     For your connection, the acceptable range of speeds is 576-600 Kbps.
     Additional Information:
     Assured Rate IP profile on your line is - 600 Kbps

  • Are my router stats ok

    Just checking
    ADSL line status
    Connection Information
    Line state
    Connected
    Connection time
    24 days, 20:44:29
    Downstream
    8,128 Kbps
    Upstream
    448 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.1 Annex A
    Latency type
    Fast
    Noise margin (Down/Up)
    14.8 dB / 26.0 dB
    Line attenuation (Down/Up)
    28.3 dB / 15.0 dB
    Output power (Down/Up)
    12.4 dBm / 1.8 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    0 / 1
    CRC Errors (Down/Up)
    3081 / 254
    HEC Errors (Down/Up)
    3155 / 0
    Error Seconds (Local/Remote)
    1142 / 145
    Speedtester results
    FAQ
    This Test comprises of two tests
    1. Best Effort Test: -provides background information.
    Download  Speed
    6658 Kbps
    0 Kbps
    7150 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 6658 Kbps
     For your connection, the acceptable range of speeds is 600-7150 Kbps.
     Additional Information:
     Your DSL Connection Rate :8128 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 7150 Kbps
    -+-No longer a forum member-+-
    Solved!
    Go to Solution.

    rustins
    Thank goodness for your reply.
    The main reason for the post was to put a little point across.
    Questions can be asked, other members whom give their time for free can reply, ratings can be awarded for that reply if it is useful or more to the point answers the question the original poster can say thanks!
    Now if I'd have posted that Q in December of last year then yes I wouldn't of had a clue. It's only through ye olde BT Beta Forums that my knowledge on certain subjects has grown to the level it is today. I've also learnt a stack of stuff from these 'thriving' forums (mainly unsolicited attempts!!!!!) and I've done my best to award a rating and to thank the poster for the reply. (If I've not then soz!).
    Now to answer your Q:
    I, by no means call myself an [Aspiring] Expert, many other members know a lot more than me. Some have made the odd post and IMHO deserve to be moved up the rankings and others have made many (they too deserve recognition). I'd sooner those with greater knowledge try and resolve other members issues. Finally Roger did get me thinking if I'd missed something and I thank him for replying. As the BTHH is pretty well locked down I replied referring to BT as that's all that one could do if all checks are carried out in the home by the user. The bit about me being confused with another customer is true (BT staff believe it or believe it not, are like us - only human and mistakes do happen) and it was in the hope that BT would double check that my hub is set back to auto. Many gamers ask for fast. I don't use my 360 online so I'm not overly fussed (yet).
    Expertise wise: I've been known to open the odd hub or 2 and report on my findings (old forum - now history). Internal images are available on request. Wireless via the HH - I've learnt a lot from General Disquiet and again while I'm at it I'll thank him too. Privacy and tracking - thanks Dorset Vinney where ever you are now. Info on the BTHH's and interference on the phone - thanks Jarviser. You might see a pattern here with user ID's.
    I'd also like to thank everyone else (too many to name) for helping me out along the way. You know who you are.
    I'm yet to tinker with the Vbox but looking on the WWW it looks like it probably isn't worth the hassle.
    Hope this answers your question
    -+-No longer a forum member-+-

  • My Router Stats and Speedtest results....

    After getting hold of BT on 150 my broadband has improved from 0.50mbps to 2.50-3.00mbps.
    My issue now is that I was at 6.30-7.00mbps in the first place so wondering if anyone can see anything wrong/affecting my speed below.....
    First Test and Results
    Download speedachieved during the test was - 3867 Kbps
    For your connection, the acceptable range of speeds is 600-7150 Kbps.
    Additional Information:
    Your DSL Connection Rate :8096 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
    IP Profile for your line is - 7000 Kbps
    ADSL driver and PHY status
    Status: Showtime Channel: INTR, Upstream rate = 448 Kbps, Downstream rate = 8096 Kbps
    Link Power State: L0
    Mode: G.DMT
    Channel: Interleave
    Trellis: ON
    Line Status: No Defect
    Training Status: Showtime
    Down Up
    SNR (dB): 13.9 23.0
    Attn(dB): 19.0 11.0
    Pwr(dBm): 19.8 12.3
    Max(Kbps): 10720 1080
    Rate (Kbps): 8096 448
    G.dmt framing
    K: 254(0) 15
    R: 12 4
    S: 1 4
    D: 64 8
    ADSL2 framing
    MSGc: 1 1
    B: 254 15
    M: 1 4
    T: 1 1
    R: 12 4
    S: 4.2500 4.2500
    L: 2040 128
    D: 64 8
    Counters
    SF: 3851041 3851039
    SFErr: 0 0
    RS: 523741646 65467663
    RSCorr: 434 0
    RSUnCorr: 0 0
    HEC: 0 0
    OCD: 0 0
    LCD: 0 0
    ES: 0
    SES: 0
    UAS: 11
    Total time  18 hours 11 min 23 sec
    SF = 3851041
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    Latest 1 day time  18 hours 11 min 23 sec
    SF = 3851041
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    Latest 15 minutes time  11 min 23 sec
    SF = 40168
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    Previous 15 minutes time  15 min 0 sec
    SF = 52931
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    Previous 1 day time  0 sec
    SF = 0
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    15 minutes interval -30 min to -15 min time  15 min 0 sec
    SF = 52930
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    15 minutes interval -45 min to -30 min time  15 min 0 sec
    SF = 52989
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    15 minutes interval -60 min to -45 min time  15 min 0 sec
    SF = 52931
    CRC = 0
    LOS = 0
    LOF = 0
    ES = 0
    Secound Test
    Download speedachieved during the test was - 2478 Kbps
    For your connection, the acceptable range of speeds is 600-7150 Kbps.
    Additional Information:
    Your DSL Connection Rate :8096 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
    IP Profile for your line is - 7000 Kbps
    ADSL driver and PHY status
    Status: Showtime Channel: INTR, Upstream rate = 448 Kbps, Downstream rate = 8096 Kbps
    Link Power State: L0
    Mode: G.DMT
    Channel: Interleave
    Trellis: ON
    Line Status: No Defect
    Training Status: Showtime
    Down Up
    SNR (dB): 13.9 23.0
    Attn(dB): 19.0 11.0
    Pwr(dBm): 19.8 12.3
    Max(Kbps): 10720 1080
    Rate (Kbps): 8096 448
    G.dmt framing
    K: 254(0) 15
    R: 12 4
    S: 1 4
    D: 64 8
    ADSL2 framing
    MSGc: 1 1
    B: 254 15
    M: 1 4
    T: 1 1
    R: 12 4
    S: 4.2500 4.2500
    L: 2040 128
    D: 64 8
    Counters
    SF: 3851041 3851039
    SFErr: 0 0
    RS: 523741646 65467663
    RSCorr: 434 0
    RSUnCorr: 0 0
    HEC: 0 0
    OCD: 0 0
    LCD: 0 0
    ES: 0
    SES: 0
    UAS: 11
    Total time  18 hours 11 min 23 sec
    SF  3851041
    CRC  0
    LOS  0
    LOF  0
    ES  0
    Latest 1 day time  18 hours 11 min 23 sec
    SF  3851041
    CRC  0
    LOS  0
    LOF  0
    ES  0
    Latest 15 minutes time  11 min 23 sec
    SF  40168
    CRC  0
    LOS  0
    LOF  0
    ES  0
    Previous 15 minutes time  15 min 0 sec
    SF  52931
    CRC  0
    LOS  0
    LOF  0
    ES  0
    Previous 1 day time  0 sec
    SF  0
    CRC  0
    LOS  0
    LOF  0
    ES  0
    15 minutes interval -30 min to -15 min time  15 min 0 sec
    SF  52930
    CRC  0
    LOS  0
    LOF  0
    ES  0
    15 minutes interval -45 min to -30 min time  15 min 0 sec
    SF  52989
    CRC  0
    LOS  0
    LOF  0
    ES  0
    15 minutes interval -60 min to -45 min time  15 min 0 sec
    SF  52931
    CRC  0
    LOS  0
    LOF  0
    ES  0

    Back to this again

  • Router stats with infinity home hub

    were can i find my line stats on my home hub ?
    i tryed looking in Services - internet but all it show there is
    Connection time
    1 days, 22:44:21
    Data Transmitted/Received (MB)
    133.0 / 71.7
    Broadband username
    @btbroadband.com
    Password
    TCP/IP settings
    Broadband network IP address
    xx.xx.xx.xx
    Default gateway
    xx.xx.xx.xx
    Primary DNS
    xxx.xx.xx.xx
    Secondary DNS
    xxx.xx.xx.xx

    If anything would contain the line stats I'm assuming it would be the Openreach modem (which we have no access to as an end user). When Infinity was installed on my line at home the Openreach engineer went to speedtest.net once he had connected everything up to the line. Apart from running one of the online speed tests I don't think there will be any other way of knowing your stats (unless Openreach decide to allow access to their modem at some point in the future).

  • Unlocked HG612 router stats monitor

    I've just come across an excellent app for monitoring the HG612 modem. It displays graphs of attenuation, SNR, bit loading, errors etc, like the well-known Routerstats programme. Note it only works on an unlocked modem.
    It's called rs-ux and is available for Windows and Linux http://sourceforge.net/projects/rsux/
    Here's some screenshots
    If you found this post helpful, please click on the star on the left
    If not, I'll try again

    There is this one too, comprising newly released compiled Windows programs based on the original batch file scripts version, allowing fully automated & unattended logging/graphing on user defined schedules if required.
    Resyncs are now detected & the data immediately logged & optionally graphed at the time:-
    http://www.freewarefiles.com/HG612-Modem-Stats_program_84567.html
    Dot Net needs to be installed to make use of the settings editor program, but a text based configuration file can be easily edited with Notepad for users who don't wish to install .Net (XP users mainly as Vista upward comes with .Net pre-installed anyway).
    Full instructions are included in the zip file which should be unzipped to C:\ ensuring expand folders or equivalent option is switched on.
    That will create the default folders structure & populate them with the relevant programs etc.
    Once unzipped, navigate to the Scripts folder & view the instructions then fine tune everything via "HG612 Settings Editor.exe" or manually edit "HG612_stats.ini" to get started.
    Attenuation per band is displayed in the "Ongoing" graphs.
    Support & any queries/feeback here:-
    http://forum.kitz.co.uk/index.php/topic,12284.0.html

Maybe you are looking for