Hi....I am new to the board and a new t3i owner.....

I have had only point n shoot cameras. Can I leave the lens on the camera when I put it in it's case? Also can it be stored for a short period of time with the battery in it? I am taking a trip and would like it ready to use in an instant. Thanks!

Hi...thank you so much for your reply. I do have a Canon case that holds both lens, the body and more. Just was afraid to leave the lens on but wanted it to be ready for use. I will be traveling by car so it will be put in a safe place. Thanks for the tip about sleep mode, had no idea. I am traveling to upstate New York and am excited about the landscape pictures I will be able to take. Any tips on good landscape pictures?

Similar Messages

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from l

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from lightroom?

In the printer driver (accessed through the Page Setup button) set the Advanced tab to borderless. Then in the right hand panel under Layout set all the margins to zero.

New to the board, and how do you change audio during conv.

Hi all, brand new IPOD owner and convert from the tired Sony MD format.:)
Now for my question. I recorded an anime video to the IPOD, but unfortunately it's in japanese. Anyone knows how to fix this?

well that depends on a lot of stuff...
did you rip it?
with what software?
did you choose english when you ripped it?
if you answered no to the first question you can't change the audio

PCI 6602:How can I use the digital lines of the board and in the same time to generate pulse train using a counter?

Hello!
My problem appeared when I tried to update my code from Traditional NI-DAQ Legacy to DAQmx.
I am using 2 counters (counter 5 and counter 7) from PCI-6602, to generate pulse train, and also the Digital I/O lines of the port 0 (the lines form 0 to 7). What I do in my application is that I am starting to generate the pulse train on the output of the 2 counters, and after that I am playing with the state of the digital lines.
In traditional there was no problem using the counters and the digital lines in the same time, everything was going perfectly, but in DAQmx this is not possible.
What happens: I start to generate pulse train on the output of the counters, no errors encountered, but when I try to modify the state of one line of the digital port the generation of the pulse train is stopped. This is happening when I start the task associated to the digital port.
My question is: it is possible to create a channel on the digital lines without altered the channels created for the counters?
Another thing what I manage to see using the "Measurement & Automation Explorer" and Test panels for PCI-6602, basically is the same thing, I generate pulse train on the output of the counter 7 and try to start a task on the digital line, but I get one error :
"Error -200022 occurred at Test Panel
Possible Reason(s):
Measurements: Resource requested by this task has already been reserved by a different task.
Device: Dev4
Terminal: PFI8"
Instead if I use the counter 0 or counter 1 to generate pulse train I don't encounter the same problem.
Which resources are used by the counters 2 to 7 from the PCI-6602 board and the counters 0 and 1 do not use?
Thank in advance for any replies!
Ciprian
Solved!
Go to Solution.

Hello Jordan, thank you for your reply.
I am sorry but I can not see or run your example, I don't use LabView, I use Visual C++ for developing.
Here is the code for generating the pulse train:
GeneratePulseTrain(unsigned long ulCount1, unsigned long ulCount2)
    short nStatus = 0;
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    nStatus = DAQmxCreateCOPulseChanTicks (m_taskHandle, "Dev4/count5", "", NULL, DAQmx_Val_Low, 0.0, ulCount1,ulCount2);
    if( bTriggerMode == true) // if hardware trigger is enabled
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_ArmStartTrig_Type, DAQmx_Val_DigEdge);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Edge, DAQmx_Val_Rising);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Src,"Dev4/PFI17" );
   //set the internal timebase
   nStatus = DAQmxSetCOCtrTimebaseSrc(m_taskHandle,"Dev4/count5","20MHzTimeBase" );
   nStatus = DAQmxStartTask(m_taskHandle);
    return nStatus;
And the code where I try to set the digital line:
SetChannelState(short nState)
    short nStatus = 0;
    uInt8 wrtBuf0[1]={0};
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    // Configure line as output
    nStatus = DAQmxCreateDOChan (m_taskHandle, "Dev4/port0/line0", "", DAQmx_Val_ChanPerLine);
nStatus = DAQmxStartTask(m_taskHandle);
    wrtBuf0[0] = nState;
    nStatus =DAQmxWriteDigitalLines (m_taskHandle, 1, 0, 0, DAQmx_Val_GroupByScanNumber , wrtBuf0, NULL, NULL);
    nStatus = DAQmxWaitUntilTaskDone(m_taskHandle,10);
    nStatus = DAQmxStopTask(m_taskHandle);
    nStatus = DAQmxClearTask(m_taskHandle);
    m_taskHandle = 0;
    return nStatus;

The board and my ti4200

Hello.. this is my first post.
I have the 865PE Neo2-LS, 2.6 GHz. First time I ever tried to POST the machine went into an endless reboot loop and my monitor went into "no signal" mode. After powering down and booting up a few times, it finally worked.
My problem right now is with the nVidia software I installed. When I try to open up the nVidia settings tool, the monitor flickers off and on. When I change resolution, or basically anything related to my monitor or video, the monitor flickers off and on. The video card is the LeadTek Winfast A280LE TDH VIVO (128MB DDR - Nvidia GeForce4 Ti4200 GPU).
Even when i go to normal display settings, when i hit the nvidia tab, it does the same flicker. But it's not so much a flicker, it's a lot slower. -- type thing.
Another thing is whenever I try to change anything in the bios, it goes back to that endless rebooting thing.
But other than that, I'm enjoying the board..

Oh yeah, one other thing I should mention is that I've already upgraded all of the drivers. All the dlls and sys files are on version 6.4.10.5216. I was just thinking maybe I should just downgrade them to an earlier version, would that help?
Thanks.
Quote
Originally posted by Lotsafire
I'm not planning on OCing..
MSI 865PE Neo2-LS i865PE, S-478 800FSB
Pentium 4 2.6C GHz w/ Hyper-Threading Technology
Leadtek A250 GeForce4 Ti4200 128MB
(No name) 512MB PC-3200 DDR400 SDRAM
SB Live! Value
Enermax 430W Power Supply
Here's my IRQs.. What's PSU?
IRQ 0   System timer
IRQ 1   Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
IRQ 3   Communications Port (COM2)
IRQ 4   Communications Port (COM1)
IRQ 5   Intel(R) 82801EB SMBus Controller - 24D3
IRQ 5   Multimedia Audio Controller
IRQ 6   Standard floppy disk controller
IRQ 8   System CMOS/real time clock
IRQ 9   Microsoft ACPI-Compliant System
IRQ 9   Ethernet Controller
IRQ 12   PS/2 Compatible Mouse
IRQ 13   Numeric data processor
IRQ 14   Primary IDE Channel
IRQ 15   Secondary IDE Channel
IRQ 16   NVIDIA GeForce4 Ti 4200
IRQ 16   Intel(R) 82801EB USB Universal Host Controller - 24D2
IRQ 16   Intel(R) 82801EB USB Universal Host Controller - 24DE
IRQ 17   Creative SB Live! Value (WDM)
IRQ 18   Intel(R) 82801EB USB Universal Host Controller - 24D7
IRQ 19   Intel(R) 82801EB USB Universal Host Controller - 24D4
IRQ 19   Realtek RTL8029(AS) PCI Ethernet Adapter   OK
IRQ 23   Intel(R) 82801EB USB2 Enhanced Host Controller - 24DD
A moment ago my PC restarted on its own, and when it booted back up again WinXP blamed my video card for the restart. Otherwise, the video card is fine. I can play games and whatever. It's just this little inconvenience which I'm pretty sure one you can help me with..?
Any suggestions? I'm guessing it's blatantly obvious but because I'm such a newb at this I'm not seeing it..

HT201441 I bought iphone from someone but I can find and contact to him again. So, after upgrading, I can not active my iphone because it require the id and password of old owner. What should I do now? I so confuse. Please help me.

I am not sure about my iphone's operating system. I just know it is a ios7.
Plz help me.
Thanks all.
<Personal Information Edited by Host>

It's a bad idea to post the IMEI and ICCID numbers for security reasons and I've asked the Hosts to remove them.
You can or can't contact the previous owner? If you can, please see
http://support.apple.com/kb/ts4515
If you can't, I'm afraid your phone is useless.

Question about the logic board and video

Hi, i own a macbook pro 17 in. @ 2.4 ghz, and have the nvida 8600 gt card. I'm pretty sure that the card has failed since no video has shown up during start up 2 weeks ago (i asked a friend of mine, and he had the same problem with a macbook pro 15 in., he was pretty positive on a card failure). I brought it to the local genius bar, and they fixed some firmware or whatnot, and it worked fine for a week. A week later, the same problem of no video showed up during start up.
My question is if this is a video card issue, is it possible that the logic board could have been damaged from the faulty video card? The tech. told me that it might be the board, and im afraid of paying the hefty repair fee, although i personally feel that the card is all to blame.

Here is the article on the NVIDIA 8600 chip:
http://support.apple.com/kb/TS2377
Note that Apple will do the repair free of charge if the chip fails within the first two years of ownership. The repair will be to replace the logic board, as Apple does not work on boards at the component level. Your machine should be new enough to qualify for the free repair.
Good luck!

PPro CS5 with Matrox RT.X2 board and software

This is on a 64 bit windows Vista Pro PC.
I would like to remove the board and un-install the Matrox software (Matrox effect patterns, Mx Tools and WYSIWYG plug-ins).
If I use the Windows ADD/REMOVE to do that will it affect my Premiere Pro CS5 in any way?
I understand that in doing this any video that used this software would no longer work, which is fine.

Thanks for the response Jim.
I decided to byte the bullet and uninstalled Matrox and the RT.X2 board.
I had no bad effects on Premiere Pro other that the sound, due to the fact that it was provided through the Matrox board.
Un-installed and reinstalled the audio board I had originnaly in the PC and assigned thos hardware to the audio in PPro and ALL is well.

How Multisim, ELVIS 2+ Board, and Labview All Connect

My school recently obtained some ELVIS 2+ boards and I have been tasked with figuring out exactly what they can do and how we can incorporate them into the curriculum as part of my work study. Now I have all the basics down for building a circuit on the ELVIS, getting measurements and controlling inputs on the computer etc. I would like to delve deeper into what the full potential of this device is by integrating it with multisim and Labview. My question is, is it possible to construct a circuit (or partial circuit) in multisim and then send the output of said circuit to the ELVIS board where it could feed into an actual circuit. For example, could I build a voltage supply virtually in multisim, and output the voltage to a specific pin on the ELVIS board where I could wire it into my built circuit? Along the same lines, could I build a circuit on the board and send the output of the circuit to a program in Labview? Is this board capable for such things or is its connections to labview and multisim just used as a comparison tool for real life readings and simulated readings? What is the full potential of this board?

Hello,
Glad to hear about you work with NI ELVIS. The integration between ELVIS and Multisim is limited to running circuit simulations and then comparing results with the real circuit, in other words, you can compare simulated vs real measurements; this is a great approach to circuits education.
Now, if you want to have more control of the inputs/outputs available on NI ELVIS, then LabVIEW is the perfect fit. In LabVIEW you can use the NI ELVISmx Express VIs to configure settings for all the instruments. Furthermore, NI ELVIS is supported by the NI-DAQmx driver, therefore you can use the NI-DAQmx functions to acquire signals from the analog inputs, generate signals in the analog outputs, access the digital I/O and program general counter/timing functionality.
Visit the NI ELVIS & NI myDAQ Instruments and Applications community to learn more about the integration between ELVIS and LabVIEW; in this page you will find some ready-to-use applications.
Hope this helps!
Fernando D.
National Instruments

Laptop G62 white screen after replacing the lcd cable to the board

Hello
i have replace de cable that goes from lcd tp the board and now i get a white display ...
what could be wrong when i was moving the hinge before i was loosing the screen but now it's only white and external screen don't display anything
Thanks

There
http://www.ebay.ca/itm/360904670472?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
the funny thing is i just replace de cable ....
Thanks

A few questions about the ka790gx and dka790gx

i have a few questions about the ka790gx and dka790gx , how much better is the dka790gx compaired to the ka790gx ? . how much difference does the ACC function make to overclocking etc , i plan on getting a phenom II 940BE or 720BE . i already have the ka790gx so would it be worth building another system using the dka790gx mobo , or should i keep what i already have and just change the cpu ?

It's largely irrelevant what other boards had VRM issues other than the KA790GX - the fact is it died at stock settings. Since there is little cost difference between the more robust DKA790GX (or Platinum if you really need 1394) why bother with the proven weakling? There are other examples around of the KA not having a robust power section. There's no way I would use even a 95W TDP CPU in the KA and absolutely not O/C.....!
As for the credentials of Custom PC, I have generally found their reviews accurate and balanced, and echo my own findings where applicable. If a little too infrequent.
The fact that the KA has such a huge VRM heatsink leads me to my other comments on the Forum, particularly regarding the "fudge" aspect:
"""Henry is spot on - the notion that adding a heatsink to the top of the D2PAK or whatever MOSFETS is effective is virtually worthless. The device's die thermal junction is the tab on the device back - which is always against the PCB pad. The majority of heat is therefore dissipated in to the board, and the fact that the epoxy plastic encapsulation gets hot is simply due to the inability of the heat to be conducted away from the device die via the tab. Not sure when Epoxy become an effective conductor of heat.... Good practice is to increase the size of the PCB pad (or "land" in American) such that the enlarged PCB copper area acts as an adequate heatsink. This is still not as effective as clamping a power device tab to an actual piece of ali or copper, but since the devices used are SMD devices, this is not possible. However, the surface area required to provide sufficient PCB copper area to act as a heatsink for several devices isn't available in the current motherboard layouts. Where industrial SBC designs differ in this respect is to place the VRM MOSFETs on the back of the PCB on very enlarged PCB pads - where real estate for components is not an issue.
Gigabyte's UD3 2oz copper mainboards sound like a good idea, on the face of it. However, without knowing how they have connected the device tabs to where and what remains a mystery. I suspect it is more hype than solution, although there will be some positive effect. From an electrical perspective, having lower resistance connecting whatever to whatever (probably just a 0V plane) is no bad thing.
The way the likes of ASUS sort of get round the problem is to increase the sheer number of MOSFET devices and effectively spread the heat dissipation over a larger physical area. This works to a degree, there is the same amount of heat being dissipated, but over several more square inches. The other advantage of this is that each leg of the VRM circuit passes less current and therefore localised heat is reduced. Remember that as well as absolute peak operating temperature causing reduced component life, thermal cycling stresses the mechanical aspects of components (die wire bonds for example) as well as the solder joints on the board. Keeping components at a relatively constant temperature, even if this is high (but within operating temperature limits), is a means of promoting longevity.
For myself, the first thing I do with a seperate VRM heatsink is take it off and use a quiet fan to blow air on to the VRM area of the PCB - this is where the heat is. This has the added benefit of actively cooling the inductors and capacitors too....
Cooling the epoxy component body is a fudge. If the epoxy (and thus any heatsink plonked on top of it) is running at 60C, the component die is way above that.....
It's better than nothing, but only just."""

OEM M/BOARDS AND MSI WARRANTY ?

Does MSI warranty OEM purchased m/boards past the 14 day period(s) offered by places such as Newegg . Meaning ... if you purchase an OEM board from Newegg and its past THIER 14 day warranty ; will/ or does MSI further cover the board for another 3yr warranty same as a retail board ?
TIA

Quote from: NovJoe on 06-May-07, 12:28:55
If it is a vanilla OEM board, no warranty by MSI.
If it is a retail OEM board, if I'm not wrong, yes warranty by MSI.
You can contact MSI and check out the actual details.
Well Ive ordered OEM's from the Egg in the past but Ive always recieved full retail boxed OEM'S , but not this time .This time it seems to be a "vanilla" OEM P6N SLI-FI from Newegg ; as it came in a plain brown box with no accessories ; so I'd imagine there would be no MSI warranty as you mentioned .
Iam having problems with the board and have till Monday to send it back . To be on the safe side , Iam think Iam just going to rma the OEM board for a full a retail box so as not have to worry about the full warranty thing .
Thx for the reply's

I am looking to upgrade my macbook pro 13". I have a new logic board and have searched for the spec on this i.e. hdd size and ram. will my 2009 screen work with a updated graphics card ??

I am looking to upgrade my macbook pro 13". I have a new logic board and have searched for the spec on this i.e. hdd size and ram. will my 2009 screen work with an updated graphics card ??

Sounds just like what was happening with my Alum MB. I took it in and they replaced my battery. It seems to be ok now. I don't know what it is, but my battery was fine before 10.5.6 and the same timeframe of the firmware updates when they came out.
My battery health was jumping around but was fine before all of this happened. Unfortunately at 381 cycles I don't think you have much chance of getting the battery for free. Perhaps you can complain about the battery saying it was fine until 10.5.6 or whatever. Not sure when your computer was made, but perhaps you are eligible for this program: http://www.apple.com/support/macbook_macbookpro/batteryupdate/

All photos disappeared from the corkboard of Iphoto, and when I try to put the new faces there,it does not register anything.The names appear under the photos,but the board remains empty.

All the faces disappeared from the cork board in my Iphoto.When I add a name to a photo it appears there,but nothing appears on the board,there is just the message,how to start.I had alrady lot of faces there and they suddenly all disappeared.I have no idea what to do, or how to start putting up the faces on the board

What version of iPhoto? Assuming 09 or later...
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD

I have a new impulse 61 key board and i have garage band. when i hit a key the sound has a delay before i hear it, i also have it hooked up to a bose radio. is there a way to correct this delay?

I have a keyboard Impulse 61. I have it hooked up to the imac and then to a bose speaker thru bluetooth and i have a long sound delay from when i hit a key until i hear sound. Is ther a fix for this delay?

The "restore disk" is built into the Mac. See About Recovery.
Need more specifics about what error messages you got while installing Adobe Flash.
However, you can almost avoid Flash altogether by setting YouTube to play the HTML5 version instead.
Click the Try something new! link at the bottom of the YouTube page.
I don't know about the sound issue. Might be hardware as you think. Try other headphones to check.

Hi....I am new to the board and a new t3i owner.....

Similar Messages

Maybe you are looking for