Hi i have a dv2000 and the power light and harddrive light have stopped working evrything else is ok

hi my hp dv2000 power light and hard drive light stopped working.
everything else is running well, any body got any idea,s running windows ultimate 7

Please identify your notebook/pc .
 Look at the base/rear/side of the notebook/pc at the barcoded sticker.
Post items numbered 1 and 2 on the following example of an HP notebook's barcodedimage. Your barcode may be slightly different but will still have the important imformation needed for us to help you.  
###Do not post the serial number as it is personal information.###
Post the installed operating system version ( and whether it is 32 or 64-bit ) and whether the CPU is an AMD or Intel product
Not posting all of the information as requested will delay our responses and slow troubleshooting of the issue that led you to author a thread.
Is your notebook/PC still within its warranty period?
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Similar Messages

  • HT201412 my camera and photo booth have stopped working, everything else is fine.

    camera shutter does not open so I cannot take any pictures. As well, the photobooth doesn't work. The red curtain just opens and closes.

    Try resetting the iPad. Hold down the sleep and home keys, past when you see the red power down slider, and until you see the silver apple. Let it reboot and see if that helps.

  • Power adapter of my macbook pro stop working

    suddenly the power adapterr for my macbook pro stop working, the charger was working normally, anyone know of any evidence to verify its operation?

    Hi ..
    Try here >  Apple Portables: Troubleshooting MagSafe adapters

  • I have pluged a portable battery to the USB and my macbook pro stopped working after that, right before it shut down there was a message on the screen that said something like " USB device is withdrawing so much power, please disconnect and connect again?

    I have plugged a portable battery to the USB and my macbook pro stopped working after that, right before it shut down there was a message on the screen that said something like " USB device is withdrawing so much power, please disconnect and connect again?
    if the device I connected have caused this, shouldn't the macbook itself have some type of protection that should prevent this from happening.
    because when I took it to an apple certified maintenance shop, the guy said that now it could only run while connected to the power. it won't run on batteries. and that I have to change the motherboard.
    can I just replace the damaged part only, would apple consider this as a design issue and they could pay for it, or should I just buy a new motherboard for 800$.
    Help.

    BB1B2,
    The problem is in finding a tech shop that will/can do board level repairs on Macs. They are few. And I certainly wouldn't spend $800 on a new logic board - I would replace the computer if I had to pay that much!
    You could call around to a few repair shops and see if they feel competent to isolate the problem and do a board level repair - but I'm afraid, in the end, that your search will be futile.
    Sorry,
    Clinton

  • I have bought the wireless keyboard for my iPad.  I was working for a day but now the power light won't stay on and as such won't connect to the iPad.  I have changed the batteries but still no difference.

    I have bought the wireless keyboard for my iPad.  I was working for a day but now the power light won't stay on and as such won't connect to the iPad.  I have changed the batteries but still no difference.

    Not knowing which wireless keyboard you bought, it is difficult to be specific.  but ...
    it is quite normal for the keyboard's power light not to stay on - it is a way of conserving battery power.
    Try this:
    turn you keyboard off
    on your iPad go to Settings > Bluetooth
    if your keyboard is listed under Devices, then touch the little blue i to its right and choose Forget this Device
    now reset your iPad:  hold both the Home and Power buttons down for about 10 seconds until the Apple logo appears, let go promptly when the Apple logo appears and wait another 30 seconds for your iPad to turn itself on
    After your iPad is back on again go back to Settings > Bluetooth
    now turn your keyboard back on and see if it appeard under Now Discoverable
         if it doesn't read your keyboard guide to figure out how to put it into Discovery mode
    touch the listing for your keyboard under Now Discoverable, it should now appear under Devices
    touch the listing for you keyboard under Devices, and choose to pair with it.

  • My screen won't work, i have tried turning it off but i cant swipe the power down button because my screen doesnt work. I have only had my iphone 4s for one day and this has happened, someone please help me.

    My screen won't work, i have tried turning it off but i cant swipe the power down button because my screen doesnt work. I have only had my iphone 4s for one day and this has happened, someone please help me.

    Did the trick!  Not sure what I did to cause the screen to go numb, but this worked perfectly!!!  I cleaned the screen and must have inadvertently selected something that locked the screen.  This perfect solution kept me from having to run to the Apple Store.  Many thanks.

  • I have a power PC that makes abunch of noise when plugged in but the power light just blinks when I press it and shows no graphics wht is wrong

    I have a power PC that makes abunch of noise when plugged in but the power light just blinks when I press it and shows no graphics wht is wrong

    Click here for information; if the computer beeps three or fewer times, remove and reinsert the computer's RAM. If it beeps four or more times, it needs to be repaired. If it's a G5, it will ignore RAM modules that aren't part of a matching pair.
    (76386)

  • Purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down.  Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death"  any suggestions?

    purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down.  Worked with the disk repair utility - fixed permissions  to hold the power button till it shuts down.  Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death"  any suggestions?
    My machine was patched to date 10.x.x.  I was lucky to get an internet connection and I selected the option to re-download Lion... its curruently being downloaded.  What if that doesn't work?
    Any thougths would be appreciated.
    Joe

    And you have a workstation? not a notebook. 
    Usually a driver or hardware, nothing that Disk utility will fix.
    You know of course what a Prohititory Sign is?
    prohibitory sign, kernel panic
    Forum devoted to Lion:
    Mac OS X v10.7 Lion Communities
    Tips and FAQs
    FAQ kernelpanic
    Resolving Kernel Panics
    Avoiding eliminating Kernel panics
    Lion App Compatibility Table - RoaringApps
    RoaringApps Mac OS X Lion Application Compatibility
    did you make sure your apps, drivers, and hardware support Lion?

  • I have just upgraded to the latest version of OSX as invited by Apple. Since then iTunes will not play and my volume controls have stopped working - in Preferences the sound controller is not able to find any input or output devices. What is going on?

    I have just upgraded to the latest version of OSX as invited by Apple. Since then iTunes will not play and my volume controls have stopped working - in Preferences the sound controller is not able to find any input or output devices. What is going on?

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
    Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
    When you see the gray Apple logo, release the shift key.
    If you are prompted to log in, type your password, and then hold down the shift key again as you click  Log in.
    *Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. 
    There will be no audio output in safe mode. The question to be answered by the test is whether any devices are listed in the Sound preference pane. After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • My iPod shuffle, which I prchased in 2009 only worked for a short time so I put it back in the box and just recently took it out. I will not charge and the power light does not come on. It was faulty from the start and thought I was out the money I paid.

    My iPod shuffle only worked for a short time. It will not charge  and the power light does not come on. Bought it in 2009. Put it back in the box and in my desk. Recently tried to get it to work again but no luck. Anyone else have this problem? Very disappointed with the product although my wifes work perfectly.

    Can't say I haven't done the same kind of thing...keep finding things I had every intention of...
    If you have the chance stop by an Apple Retail store and talk to them about it...they often work deals for replacement of out of warranty non-working items for prices around half price.  Won't hurt to stop by and see what they will do for you.

  • My acer R7 sometimes will not power on, even when the power light is on, do i have a virus?

    My acer r7 will not power on even with the power light on? Do i have a virus???

    dcdungan,
    If the power light is on, it is powering on. There could be a problem with the display itself or a driver, have you tried connecting an external display and seeing if something comes on the screen?
    Do you see absolutely nothing on the screen when it is powered on, not even the splash screen?

  • My computer's power adapter is plugged into a power source, yet the indicator light is not working and my computer is not being charged.

    My computer's power adapter is plugged into a power source, yet the indicator light is not working and my computer is not being charged.

    I have the same issue.
    The magsafe goes orange for about 20 seconds, the battery shows 0% then it goes to a black X indicating no battery installed.
    With a new battery the same happens, although it can run on battery but does not charge.
    It runs fine on mains power, the green light is always lit.
    I have tried several things so far:
    1. Cleaned the magsafe contacts on cable and macbook
    2. Reset SMC and PRAM
    3. Installed latest battery update
    4. Tried new battery
    5. Put old battery in fridge for an hour
    I work in IT and am fairly confident taking it apart, what should I try next?
    Some people recommend a new battery connector, which doesn't seem to make sense as the battery has never been removed before.  Also some people say it will need a new logic/motherboard.
    Any experts here managed to sucessfully fix one of these?

  • Upon pushing power button my mac pro sits in a holding status with the power light blinking continuously.  Fans kick on and it never goes to startup.  Trickle LED shows good as does the Power LED.  No RAM DIMMS are lit either.

    Upon powering on my Mac, the power light begins to flash, the fans kick on and the it seems to lock up.  Screen does not come on.  I have confirmed it has Trickle and Power by checking the diagnostic LED's on the mother board.  No other LED's are lit.  None of the RAM LED's are lit either.  I removed the battery from the motherboard and waited ten minutes, then reinstalled it.  What could the issue be?
    Mac Pro specs are:
    OS X, Duel Processor, 2.6 GHz, Duel Core, Intel Xeon, 12GB DDR2 RAM

    As a general rule, pairs in adjacent slots. Largest sizes on lowest-numbered slots on each riser in turn. It will in work most any order, then when you get close to a final arrangement there is a small .pdf manual available that shows "optimum" arrangement.
    Mac Pro (original and 8-core) Memory Replacement Instructions

  • I plugged a usb in to my macbook pro and rhe computer went off and wont turn back on.  the power light doesnt light.  what do i do??? help!

    i plugged a usb in to my macbook pro and rhe computer went off and wont turn back on.  the power light doesnt light.  what do i do??? help!

    Do you have Apple Care? Is there an Apple Store near you?
    Sounds like a hardware fault...

  • Help please - have a Nano and a Shuffle and neither are working! The Nano wheel appears to have stopped working - I can't get it to do anything. I've done the reset,it worked the first time but not since. And the shuffle won't sync with my library!

    Hi,
    I have an iPod shuffle 4th generation and an iPod Nano 5th generation . The Nano wheel appears to have stopped working - I can't get it to play or anything. I've done the reset and it worked the first time, but now the only way I can get it to play anything is to shake it and go with the shuffle choices - I can't change volume, song, pause or turn it off.
    So, I decided to start using the Shuffle which I was given as a present last year. I've plugged it into my laptop (running windows 8 and newest version of iTunes). It appears in iTunes on the left hand side, but when I click to sync (whether I tick sync all or choose artists) it says synched but has no music. It seems to not be linked to the music library - when I tick synch all songs, next to the "sync music" it says 0 songs?
    Any help to fix either would be really appreciated - I'm without any music at the moment and I'm going away this weekend!
    Thanks

    Hi Bblairjones,
    If you are having issues with your Nano and Shuffle, you may want to try the Troubleshooting Assistants on the following page:
    Apple Support: iPod Troubleshooting Assistants
    http://www.apple.com/support/ipod/five_rs/
    Regards,
    - Brenden

Maybe you are looking for

  • Everytime I open itunes I get a message saying itunes has stopped working and windows is looking for a solution

    Everytime I open itunes I get a message saying itunes has stopped working and windows is looking for a solution

  • Difference in GL balance and asset report

    Hi Experts The scenario is difference in the asset report and GL report for the year 2009. The year is not yet closed in asset accounting.I have run the ABST2 and it shows difference  in the GL for AUC .The asset balance report S_alr_87011964 & s_alr

  • Will actionListener work in 1.4?

    I have the following code written in 1.2.2. It works fine. But when I tried this in 1.4.1, it is not working. This is where the user enter the userid and password and push the "Login" button. class SISHandler implements ActionListener public void act

  • AVG as an analytic function - gives error ORA-0439

    I'm trying my first implementation of AVG as an analytic function. I took the following query which gave a simple average: SELECT PERSON.LASTNAME, COUNT(TO_NUMBER(RPTOBS.OBSVALUE)) CNT, AVG(TO_NUMBER(RPTOBS.OBSVALUE)) AVRG FROM TUT.PERSON PERSON, TUT

  • Unable to remove Bold font - Hr payslip

    Hi All, USING PRINTRONIX printer ( P7220 ). using the standard format type X_44_120 for country Thailand.   I have developed HR payslip using transaction PE51 to print HR payslips. Now all the data & the alignment is fine. Only problem iam facing is