Hi, i have a problem receiving calls on my 6 plus ios 8.1.2

when i receive an incoming call the phone rings only once and disconnects the call automatically, can someone please help me fix this issue?
I tried removing the sim and replacing
checked "DO NOT DISTURB" settings
reset the network settings
reset the phone
but i couldn't figure the problem,
thank you,

Similar Messages

Since installing iOS 6, I have had problems receiving calls and messages. Calls go straight to answerphone and messages do not appear until I switch off and on again. I have also installed iOS 6.1.1

Since installing iOS 6, I have had problems receiving calls and messages. Calls go straight to answerphone and messages do not appear until I switch off and on again. I have also installed iOS 6.1.1

Try a reset. Press & hold the Power and Home buttons simultaneously, ignoring the red power off slider, until the Apple logo appears. Then release both buttons. This should not affect any content on the iPad, it is similar to rebooting your computer.

Since i update my iPhone 5 with IOS 7.0.2, I start to have serious problems to call or receive calls from other telephones: is not possible to open the call at the first try. Somebody have the same problem?

Since i update my iPhone 5 with IOS 7.0.2, I start to have serious problems to call or receive calls from other telephones: is not possible to open the call at the first try. Somebody have the same problem?

Try
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data

Hi I have a iPhone 4 and I seem to have a problem during calls. If I make or receive a call I can hear the person who is on the line with me but the other person can't hear me. This problem has occurred 1 week ago so please get back thank you

Hi I have a iPhone 4 and I seem to have a problem during calls. If I make or receive a call I can hear the person who is on the line with me but the other person can't hear me. This problem has occurred 1 week ago so please get back thank you

You use Restore to get the latest firmware build, not the Update button. You can only use the Update button, if there is an iOS update, say iOS 5.1.
this link talks about updating to 9A406 to fix the "No Service" issue with iPhone 4S:
http://iphone-and-i.blogspot.com/2011/12/fixing-iphone-4s-signal-problem.html

Hello apple I have the problem with my iPhone and my friends have this problem too. My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it bu

Hello apple
I have the problem with my iPhone and my friends have this problem too.
My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it but when answer both of us can't hear anything and when I put my iPhone to my face the screen is still on and when I quit the phone application and open it again it will automatic call my recent call. And when my friends call me my iPhone didn't show anything even the missed call I'm only know that I missed the call from messages from carrier. Please check these problem I restored my iPhone for 4 time now in this week. I lived in Hatyai, Songkhla,Thailand and many people in my city have this problem.
Who have this problem??

Apple isnt here. this is a user based forum for technical questions. The solution is to restart, reset, and restore as new which is in the manual after that get it replaced for hard ware failure. if your within your one year warranty its replaced if it is out of the warranty then it is 199$

I have the problem of calls getting failed.. Black Iphone 4S 16gb IOS 6.1.3. O2 Network. Airtel India. I have full bars of signal but cannot make calls. Goes to "No service" then to "searching". I constantly get "Call Failed" when making calls.

I have the problem of calls getting failed.. Black Iphone 4S 16gb IOS 6.1.3. O2 Network - Airtel India.
I have full bars of signal but cannot make calls. Goes to "No service" then to "searching".
I constantly get "Call Failed" when making calls.
What could be done to solve the problem?

Try settings/general/reset/reset network settings. If that does not do it then contact your carrier

I have a problem in the Bluetooth headset after updating iOS 7

I have a problem in the Bluetooth headset after updating iOS 7

Hi,
have a similar problem here. More specifically, I am using a Plantronics Voyager Legend (brand new) with my Iphone5 (iOS 7.0.2). All apps are working great with the headset, e.g., listening to music, normal phone calls, etc. No sound distortion at all.
When I use Skype (most recent version, which is 4.12.258) the sound is very distorted, like scattered. I also successfully used the same headset with a Samsung Galaxy S3 and Skype. No problems. So, I suspect that it must be the combination of Iphone/iOS7 and Skype which messes up the sound.
Does anybody else have the same problem when using that combination of devices and apps?
Best,
Kurt

I have a problem with my iphone,after upgrade software ios 6.0.1, is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL was not found

I have a problem with my iphone,after upgrade software ios 6.0.1, is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL was not found

You have to go to autherized iPhone agent.

I continuously have a problem making calls where I have to activate then cancel the speaker phone button. Normally happens when calling landline phones but sometimes mobile. Any fixes?

I continuously have problems making calls from my iphone 4S. When I place a call and press send, you hear nothing until I turn on and off the speaker button and then you hear the ring tone or the person answering. This happens normally on land line calls but does occur when calling mobile phones somethimes. Is this a common problem or is there a fix for it? Thanks

I am having the same problem. Usually happens after I make consecutive phone calls.

SPH200D Netgear Problem - Receiving Calls

About 6 months back my Netgear SPH200D started to give me problems in receiving calls. The phone either rings for the caller and we do not hear it or once picking up the call the original caller is never heard across the line. The solution everytime is to disconnect the power cord from the base unit for 20 seconds and let the system restart on the handset again for it to work. Lately this has been happening more often. Any advice would be appreciated. Thanks

Thanks very much, yes Do not disturb was turned on, and that was obviously stoping the first call coming through, but allowing a second one from the same number within the time window of 3 minutes. Happened by mistake , but I shall make sure I don't do that again!!!

New 4s connects with bluetooth in my Lexus, but I have intermittent problems with calls. I can hear them, but they can't hear me. Never did this with 3gs. Anyone else have this problem?

New 4s connected to my Lexus bluetooth. Having intermittent problem with calls. I can hear them, but they can't hear me. Never a problem with 3gs phone. Anyone else having this problem?

I ended up getting a new phone, straight through Apple. I called their technical support and went through all he basics again and they decided to replace it. Was a pretty quick process - after defaulting and resetting the whole phone (about 2 hours), I called them back to inform that there was no change, so they set up the order.
I had to give my CC# so they could hold a charge on it (in case I didn't send my old phone bach, which they sent me a pre-posted package to send it in anyway). Had a brand new iPhone 4S in my hands in 4 days, which was pretty decent. I had uploaded everything previously to iCloud, so setting up the new phone was a snap.
Only thing I really didn't like was they charged me almost 30 bucks for shipping or processing, or something. Not so sure that should have been my responsibility after spending so much on a brand new product, only to have to have it warrantied after, like, a month.

Can not make or receive calls on iPhone 6 plus

How to fix this problem when can't make or recurve calls on iPhone 6 plus.

@Loomy77
Try the solutions below to see if you can move forward:
settings>cellular>turn cellular data off>wait 10 seconds>then turn it back on and test
if that fail
settings>general>reset>reset network settings

Dear i have a problem with the fingerprint after updating to ios 7.1 when plugged in electricity works like a charm

dear sirs.
i am an apple customer since first iphone but right now i am having problems with fingerprint sensor after updating to ios 7.1.
when plugged to electricity it works but when unplugged sometimes work.
please solve this issue by a quick update and thanks.

I have been on the phone twice today with my carrier. They reset it the first time, it worked for an hour then messed up again. They reset it a SECOND time.. It worked for 6 hours, then messed up again. I don't know if this is a software issue or what but if ANYONE has any insight, I would appreciate it greatly.

Does anybody have any problems receiving phone calls or txts or any kind of services on iphone4 with verizon? I get no calls txts or internet connection!! Anyone with same issue??

I started having problems with my iphone4 since i first got it 2/10/11. Phone calls were automaticlly forwarded to voicemail. Got a replacemnt phone and still same issue. But now I am not receving phone calls txts and have no internet connection!!!! I spoke to Verizon and they opened up a trouble ticket...its been days and havent heard back from them. I used a different verizon phone in the same area where my iphone is not working and that phone worked perfectly fine which means it is not the signal. Anyone having the same problem??? Plz help!!!

Hello Idkallday!
I know your device sends and receives text messages! Let's get to work on this! Did you port your service from another carrier, or is this a new number? Is your previous device still powered on?
I also want to ask if you are able to use iMessaging, and if you see any error message when sending?
Please test it by sending a message to your own mobile number, and keep us posted!
ChristinaB_VZW
Follow us on Twitter @VZWSupport

Have a problem in calling a subcontroller

I try to use the model class and call a subcontroller class to display data in another view by using the following code.
In the do_init
 Create the model of this class
 l_model = create_model( model_id = c_model_id
 class_name = lc_class_name ).
 Create sub controller
 l_controller ?= create_controller(
 controller_name = lc_control_name
 controller_id = c_subcontrol_id ).
 controller_set_active( controller_id = c_subcontrol_id
 active = 0 ).
 l_controller->set_model( model_id = c_model_id
 model_instance = l_model ).
In the do_request
 controller_set_active( controller_id = c_subcontrol_id
 active = 1 ).
 call_controller( l_subcontrol ).
 clear current_event.
At the view of subcontroller, after any event occurs, the parent controller is triggered again. Why? How can I solve this problem?

I do appreciate your immediate reponse. However, there may be some misunderstanding. Of cource, I put the checking coming event in the do_handel_event. The details of my application is shown below.
In the do_init method, all source code is the same that I posted. It has creating a model class and then a subcontroller class.
In the do_request method, I have a code like this.
dispatch_input( ).
main_view =
 create_view( view_name = 'main.htm' ).
l_model ?= get_model( c_model_id ).
To separate tasks between calling a view and calling a subcontroller, I have to have a flag, current_event, to check whether the coming event is search. This flag is set at the method 'do_handle_event'
if current_event eq lc_search.
 l_subcontrol ?= get_controller( controller_id = c_subcontrol_id ).
 controller_set_active( controller_id = c_subcontrol_id
 active = 1 ).
 call_controller( l_subcontrol ).
 clear current_event.
elseif current_event is initial.
 call_view( main_view ).
endif.
In the do_request of my subcontroller class, I call the view of the subroutine.
dispatch_input( ).
l_model ?= get_model( 'mm' ).
stock_view = create_view( view_name = 'stock.htm' ).
stock_view->set_attribute(
 name = 't_display' value = l_model->t_display ).
stock_view->set_attribute( name = 'ITERATOR' value = me ).
stock_view->set_attribute( name = 'show_popup' value = show_popup ).
call_view( stock_view ).
After any event occurs in this view of subroutine, I catch this event at the method do_handle_evnt.
if htmlb_event is bound.
 case htmlb_event->server_event.
 when 'onSelect'.
 CLASS CL_HTMLB_MANAGER DEFINITION LOAD.
 tv ?= cl_htmlb_manager=>get_data(
 request = request
 name = 'tableView'
 id = 'stock_tv_display' ).
 if tv is not initial.
 table_event = tv->data.
 row_index = table_event->row_index.
 if row_index is not initial.
 show_popup = abap_true.
 endif.
 endif.
 when others.
 endcase.
endif.
After the program run through this method, it goes back to the do_request of the parent controller, main.do. This is my problem. I don't want to call the parent controller again. And, my application has already been stateful. Is there any way to prevent it. I sincerely appologize if I couldn't catch what you said. But, please give me some suggestions to solve this problem.
Message was edited by: Amateur willbeProfessional
Message was edited by: Amateur willbeProfessional

Hi, i have a problem receiving calls on my 6 plus ios 8.1.2

Similar Messages

Maybe you are looking for