Hi, I need help. On my channel strips, I don't have a Midi FX tab. What do I do? I have Logic Pro X.
Can anyone help please?
In case you don't know, MIDI effects can only be put on a software instrument channel, so if you are expecting it to be on the main track of, say, a drummer producer kit it won't be there because that is an aux track. Right click somewhere on an instrument channel strip in the inspector or mixer and find the "channel strip components" sub menu - you'll see the MIDI effects with or without a checkmark next to it. The mixer and inspector can be set up independantly - which I didn't know until just now.
Edit: Curse you and your succinctness CCTM!
Similar Messages
-
Need help on my email account but don't have a BB service .
How can I access my email I dont have bb service. I do have wifi already link in the phone. How can I override the bb? I used the Red Pocket mobile service. Any help is highly appreciated. Oh btw, they give me this bunch of configuration that I can't configure LOL and dont know which button even the instruction too much for a non hight tech girl like me . Please help!!!
Solved!
Go to Solution.with out a BlackBerry Dataplan, you can only use web mail even on wifi
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V -
Need help accessing the router web page. I have been tol...
Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanksWhat router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM -
Please help me!--rendering makes the images or video blurry (very pixelated) deteriorates the image Adobe Premier Elements 13 need help! .jpg and mpeg images, but I have never "rendered" before since I got APE 13 about 6 weeks ago. I am desperate for assistance!
That's going to be a ridiculous waste of money and energy.
First of all, the current ATI drivers don't support multiple GPUs, so at the moment even a single 4870X2 would be only a 'normal' 4870 (which is quite a speed beast already). GFX drivers evolve rapidly, so things might look different next month, but when it comes to Linux and hardware there's one Golden Rule: stay away from the newest stuff and wait for proper support to get coded.
I also wonder what power supply could possibly cope with the differences between idle and full load; that's way beyond 400W. But then, I'm one of those "quiet&green" types where >100W idle is already a bit much.
I kind of understand that you want to get it done and not worry about hardware for the next 10 years or so, but that's simply not how the hardware world works and never did. At least not for the average consumer. -
hello, i need help i'm doing experiment on ilab i have managed to put my experiment on the platform but when i try to launch it fails with an error 404 that the page not found. any one with idea of what i should do to solve this problem. thank you
hey Sally,
Can you elaborate on the ilab and what you are trying to do? I have found this page to explain error 404, but I am not sure if it directly applies to you
http://digital.ni.com/public.nsf/allkb/D0998D3734926FA08625782300016E40?OpenDocument
Regards,
A. Zaatari
National Instruments
Applications Engineer -
I need help to find my iphone 5C. I have id apple but perhaps I can do more to find it. Please contact to ********
<Edited by Host>Hi Oliveira_Lisboa,
The article below has some information about the options and features available, it also has some tips that might help you locate your iPhone.
What to do if your iOS device is lost or stolen
http://support.apple.com/kb/ht5668
If you lose your iOS device or think it might be stolen, these steps may help you locate it and protect your personal data.
If you enabled Find My iPhone on your missing device
These steps require that Find My iPhone was enabled on your device before it was lost or stolen.
Attempt to locate your device using Find My iPhone at icloud.com/find, or using the free Find My iPhone app.
Put the device in Lost Mode to set a 4-digit passcode and display a custom message with your phone number on your device. While the device is in Lost Mode, you can also keep track of changes to your device's location. Lost Mode requires that your missing device be using iOS 6 or later. If your device is using iOS 5, you can still lock your device remotely and display a message on the screen.
If you want to delete all of your personal information from your missing device, you can erase it remotely. Please note that when you erase a device, you will no longer be able to locate it.
Report your lost or stolen device to local law enforcement and your wireless carrier. Apple doesn't track or flag lost or stolen products, but you can use My Support Profile (supportprofile.apple.com) to find a list of serial numbers for products that you've purchased or registered with your Apple ID.
Note: If your missing device is offline, you can still put it in Lost Mode, lock it, or erase it. Your commands will take effect when the device comes back online.If you did not enable Find My iPhone on your missing device
If you did not enable Find My iPhone before it was lost or stolen, you can't use it to locate or protect your device, but you can still follow these steps:
Change your iCloud password to ensure that no one else can use your device to delete or make changes to your iCloud data.
Report your lost or stolen device to local law enforcement and your wireless carrier. Apple doesn't track or flag lost or stolen products, but you can use My Support Profile (supportprofile.apple.com) to find a list of serial numbers for products that you've purchased or registered with your Apple ID.
Additional Information
Visit iforgot.apple.com/appleid if you need help remembering your Apple ID.
-Jason -
ok so my i need help with my iphone 4s... i have about $5.00 of credits left of the itunes card i got and i decided to get a show and it says i need to verify my credit card, why doesnt it just use the credits i have? its under 5 bucks? help me please
You have to do it here for help
iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html -
i do need help. My little i-pod appears to have lost all visuals. when I
connect it to the computer I can see what is there, but I can no longer
play it or see the tiy screen. Does this mean it has died? or is there a
way of resucitating the poor thing.
mkiPod Tutorials
iPod Manuals
iPod Models -
I have logic pro studio 8 and the upgrade (logic pro 9) and it will not load up to my new mac book pro. Its asking for a product key for the logic pro 9 upgrade and there wasn't one in the box. i need some help
Contact AppleCare... Explain you are a Logic User and you should be transfered to a Product Specialist to assist you with your Issue.
-
hard drive crashed, replaced drive and need to reinstall CS5 Extended but I don't have serial number, only product code on box. How do i get my serial number?
Beamer96 if the software has been registered then it will be under your account at http://www.adobe.com/. You can find more details at Find your serial number quickly - http://helpx.adobe.com/x-productkb/global/find-serial-number.html.
-
I have credit and it's less than 0.99 and i need to change the region and i don't have visa
i have credit and it's less than 0.99 and i need to change the region and i don't have visa
Click here and ask the iTunes Store staff to zero your account balance.
(110223) -
I download Adobe Flash but it doesn't install. Each time I encounter something that needs Adobe Flash it tells me I don't have it. I am getting tired downloading it and then it isn't there.
install_flash_player_10_osx.dmg
install_flash_player_10_osx-1.dmg
install_flash_player_10_osx-2.dmg
install_flash_player_10_osx-3.dmg
install_flash_player_10_osx-4.dmg
etc to -9
Those are the ones you downloaded. Ten times, apparently. Since install_flash_player_10_osx.dmg already existed, the next download was appended with -1. The next -2, etc. They'll all be identical, so it doesn't matter which one you use. Though I'd go with the last one as it may be a slightly updated version from the first download, depending on how long ago you did the first one.
A .dmg file is a Disk Image. When you double click them, they open up a pseudo drive on the desktop. When you open one of these ten items, the Flash installer will appear in a file window. Run it to install Flash. Then close the file window (displaying from the psuedo drive) and then put the "drive" in the trash to dismount it. You can then delete all of those.
Looks like you also downloaded the Adobe Reader twice. Versions 10.1.2 and 10.1.3. Also Skype, whatever the Thomson thing is, and an unnecessary Flash uninstaller (the Flash installer will put an uninstaller in the Utilities folder). -
I need to re install lion but i don't have a disk it was a download?
i need to re install lion but i don't have a disk it was a download?
Hold ⌘R on Boot and then select Reinstall OS X Lion
-
Hi I just bought an Adobe photoshop lightroom 5 from amazon. It just came in the mail, and I am trying to install it. What I am having problem is the serial number. As I put the serial number in it says that this is an updated serial number and it needs the previous serial number. I don't have that because this is the first light room I have.
You purchased the wrong license. You should have purchased Lightroom at the full price. I don't know what the Amazon price is, but Adobe sells it for $149. You will have to contact Amazon and see if there is any way you can exchange for the right license.
-
New logic user, need help with multi-channel inst and aux strips.
Greetings all,
So I just purchased a new Mac Pro 2.66 and Logic Pro 7 to run with it. I have been a long time Nuendo/Cubase user on the PC side of things but since I got the Mac I wanted a DAW that was supported fully for the apple platform.
Anyways, its a world of difference and I am very confused as I wrap my head around the learning curve, so in the meantime I have one important question maybe some one could help me with.
The question is regarding Aux channel stips for Multi channel instruments. In this scenario I am working with Battery 3, it took me a while to understand that I actually needed to create these aux channels just to have seperate outs in Battery which seems really wierd and overly time consuming.
As an example in Nuendo once you create the instance of Battery, the audio mixer automatically just creates the corresponding stereo and mono channels instantly. This obviously makes is a sinch to assign Batteries pads to seperate outs for eq/comps for seperate sounds.
Now the Battery manual doesnt even make a reference to Aux channels for assigning outs in Logic, I actually had to do a Google search to figure this out.
Anways, sorry for rambling...
Here is the main issue.... How can I quickly and easily create multiple Aux's? In the mixer there is really only enough room in there to add like 1 more Aux strip, if I want to add more than that I need to re-arrange the entire global mixer which seems like a crazy system, surely there must be a more convenient method for getting muti-channel audio instruments set up quicker.
Any help you can assist with would be exceptional!
Thanks in advance.Not sure what exactly your question is, especially since I don't use battery. But as far as creating aux tracks:
• go to the audio layer of the environment (not the track mixer window), find the two defalt aux tracks
• Highlight all tracks to the right of the aux tracks (these should be bus and output tracks), and drag to the right far enough to fit in a bunch of aux tracks; you might even want to drag the all underneath the aux tracks, if your screen accomodates
• use the key command shift-command-a multiples times to create several new "audio objects", and double click each one to expand
• highlight all the new objects and select options/clean up/ align objects (makes it look nicer)
• still highlighted, over in the parameters section (left side) select a channel, setting it to the highest number aux (at this point, probably "aux 3")
• now individual set the channel for each aux track – you'll see that now you have available "aux 4"; next time you set a successive track you'll see "aux 5" and so on
• once you've got things set up the way you want, save it as a template so you don't have to do this again later
Maybe you are looking for
-
Error occurred while deploying ear file
Hello experts, I am using NWDS (NW Version: 7.0.18). For a particular java file I am getting this error: ERROR: Not deployed. Deploy Service returned ERROR: 20110728174758 Info : java.rmi.RemoteException: Error occurred while de
-
Getting error while installing Release 12 on SuSe 9 ( No Service Pack3)
Hi All, I am trying to install Release 12 Vision on SuSe 9 Server. In the Middle of installation, I am getting this error. RW - 50004: Error code received when running external process. Check log files for details. Running database install driver for
-
For God's sake Nokia...PLEASE release the N950!!
This sexy piece of hardware is the right one to replace the Maemo 5 giant, our beloved N900. I know it, I know you guys know it as well. I'm looking at it and say "holy **bleep**, this device is thinking!" N900/N950 enthusiasts, back me up here!
-
Hi, I'm currently creating a gantt chart using Sap Netweaver developer studio. I'm using the business graphic to create it. But I'm unsure on how to create the series bar on the gantt chart for each category. I want my gantt chart to be those for pro
-
"Not" operator in iTunes search?
Just wondering if anyone knows if there is a "not" operator to exclude a word from your itunes search, say to keep if from picking upi tracks you don't want. This operator would function in a way that would be similar to the "-" operator on google, s