HI,I want to ask one question about SRP 521W

   I have one SRP 521W router, It is slow when I configure it,And the memory utilized very high(94%),but the CPU is nice.
   I was upgraded the last release firmware,The memory utilization keep in 78%,But I am still feeling it slowly when I configured it,How can I fix or correct configure it,Can to reduce the memory utilization.    I have one SRP 521W router, It is slow when I configure it,And the memory utilized very high(94%),but the CPU is nice.
   I was upgraded the last release firmware,The memory utilization keep in 78%,But I am still feeling it slowly when I configured it,How can I fix or correct configure it,Can to reduce the memory utilization.

Dear Shipeng,
Thank you for reaching Small Business Support Community.
Since the firmware upgrade did not fix the problem, you can try disabling some by default enabled services that you may not need; things like:
Administration > Remote Management > SNMP and Local TFTP.
Network Setup > UPnP
Administration > Log
Network Setup > Firewall > Firewall Filter
If no Internet Protocol Television (IPTV), Network Setup > IGMP
You may also check on the Internet Access Control entries to get rid of any not needed entries. Please check these out and let me know if there is any further assistance I can help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

I want to ask the question about phasor measurement.

I want to ask the question about phasor measurement.the first one is that how can I accomplish the sychronized sampling with GPS?The other question is that how can I adjust the sampling rate for DAQ when the system frequency alter continuously.(if I used the DFT,due to the altering of frequency,I can't get the completed waveform)"

Synchronising DAQ with GPS depends on the DAQ sampling rate. If the rate is higher than 2 Hz you can sample the 1PPS pulse of your GPS receiver together with your data.
You change the sampling rate with the AI Clock Config.vi. You cannot do this on the fly so you must stop DAQ with AI Control.vi reconfigure the sampling rate and then start it again.
Waldemar
Waldemar
Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
Don't forget to give Kudos to good answers and/or questions

Hello , I want to ask some question about ipads \ How powerful is the iPad? How useful is it for reading books, newspaper or magazines or for surfing the web? Can you identify any shortcomings of the device? please help me :(

Hello ,
I want to ask some question about ipads \
How powerful is the iPad?
How useful is it for reading books, newspaper or magazines or for surfing the web?
Can you identify any shortcomings of the device?
please help me

it's less powerful than your average computer. THink of it like a netbook but with a better processor.
It'll do fine for surfing (although if you browse a lot of flash based sites you will need to get a third party browser since safari doesn't accommodate it)
You may do OK on reading books, papers or magazines, especially if they have apps, but the ipad's screen is backlit, so it doesn't work well outdoors and you may need to fiddle with the brightness so that you don't get eye strain (it's just like doing too much reading from a computer screen)
I would say the biggest short comings are data transfer. Apple's preferred work flow is that everything is done via iTunes or the internet....well people dont' always have 100% reliable always on internet access so you can find yourself in a situation where you can't get things on/off the iPad.
By and large, it's a good device for day to day stuff, but is not a computer replacement.

I wanted to ask a questions about financing

I want ask a question about financing 2 macbookpros?

You need to call Apple about that. These are just user forums. We're all users here, like you.

HT4539 Sir i want to ask one question ?

sir have given my ipod to my friend to sync some games in my ipod and he done that but when i connected through my itunes it is not sync any apps from my itunes orit is not been use by my itunes please sir u can help me out... please do respectively what i can do..
<Email Edited By Host>

Dear Shipeng,
Thank you for reaching Small Business Support Community.
Since the firmware upgrade did not fix the problem, you can try disabling some by default enabled services that you may not need; things like:
Administration > Remote Management > SNMP and Local TFTP.
Network Setup > UPnP
Administration > Log
Network Setup > Firewall > Firewall Filter
If no Internet Protocol Television (IPTV), Network Setup > IGMP
You may also check on the Internet Access Control entries to get rid of any not needed entries. Please check these out and let me know if there is any further assistance I can help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

New comer wants to ask a question about "mailto".

Hallo!
I would like to make a link that open a new mail window. I am have used the JtextPane class to edit and display the text.
Thanks in advance!
James
here a part from my code
private static JTextPane Header ()
     StyleContext context = new StyleContext();
     Style header = context.getStyle(context.DEFAULT_STYLE);
     StyleConstants.setAlignment(header, StyleConstants.ALIGN_RIGHT);
     StyleConstants.setFontSize(header,14);
     StyleConstants.setSpaceAbove(header, 0);
     StyleConstants.setSpaceBelow(header, 0);
     StyledDocument header_doc = new DefaultStyledDocument(context);
     String[] Header ={ "my Name " + newline,
                    " my profession"+ newline,
                    " my address " + newline,
                    "my P.O. box " + newline,
                    "my phone " + newline,
               "E-Mail: [email protected]"}; // I would like to add here a link that refer to mailto.
          try
          for (int i = 0; i < Header.length ; i++)
          {                                                                       header_doc.insertString(header_doc.getLength(),Header[i],header);
          catch(BadLocationException badLocationException)
               System.err.println("oops");
     JTextPane tpHeader = new JTextPane(header_doc);
     tpHeader.setMargin(new java.awt.Insets(0,0,0,40));
     return tpHeader;

Hallo!
I would like to make a link that open a new mail window. I am have used the JtextPane class to edit and display the text.
Thanks in advance!
James
here a part from my code
private static JTextPane Header ()
     StyleContext context = new StyleContext();
     Style header = context.getStyle(context.DEFAULT_STYLE);
     StyleConstants.setAlignment(header, StyleConstants.ALIGN_RIGHT);
     StyleConstants.setFontSize(header,14);
     StyleConstants.setSpaceAbove(header, 0);
     StyleConstants.setSpaceBelow(header, 0);
     StyledDocument header_doc = new DefaultStyledDocument(context);
     String[] Header ={ "my Name " + newline,
                    " my profession"+ newline,
                    " my address " + newline,
                    "my P.O. box " + newline,
                    "my phone " + newline,
               "E-Mail: [email protected]"}; // I would like to add here a link that refer to mailto.
          try
          for (int i = 0; i < Header.length ; i++)
          {                                                                       header_doc.insertString(header_doc.getLength(),Header[i],header);
          catch(BadLocationException badLocationException)
               System.err.println("oops");
     JTextPane tpHeader = new JTextPane(header_doc);
     tpHeader.setMargin(new java.awt.Insets(0,0,0,40));
     return tpHeader;

Hello , how r u, can i ask 1 question about xcode, i have mac os x 10.7.5 , n xcode version 4.6.3 i want build apps for ios 7.1 n mac os 1.9 ,, , but my macbook is old late 2008 macbook 4,1, so can i develop apps for ios7 n 1.9 using xcode 4.6.3, bcz my

hello , how r u,
can i ask 1 question about xcode, i have mac os x 10.7.5 , n xcode version 4.6.3 i want build apps for ios 7.1 n mac os 1.9 ,, , but my macbook is old late 2008 macbook 4,1, so can i develop apps for ios7 n 1.9 using xcode 4.6.3, bcz my machine cant upadte on 1.8 n 10.9,, ihave 2gb ram . core 2 duo pr, plz rely asap,
thnxs

Please type complete sentences and words. This isn't an instant message program.
https://developer.apple.com/support/ios/ios-dev-center.html

Okay i just recently asked a question.about my factory unlocked iphone 3gs asking how to activate it but..

i probably shouldnt say this but,okay i just recently asked a question.about my factory unlocked iphone 3gs asking how to activate it. so i got too excited of aving it and couldnt wait for my tmobile sim card to come one more day. so i "hactivated" it (i know this voids all warrenty) and i jailbroke it just so i could use it as an ipod.it worked and i was syched.
BUTTT.... it asked me if i wanted to update the software to 5.1 and i was like " oh yes id love to" and it started downloading it and it was inrecovery mode the whole time .
when the download finished. i hit restore so i can put the software on the phone but the itunes had an error and the phone went glitchy and it does a rebooting loop. it shows the apple symbol with the slash through it for about 5 seconds and shuts off for a little bit (about another 5 seconds) and it starts up then loops the process. ive managed to turn the phone off but if i start it up it loops...what should i do? any help :/
Also it does not show up in my itunes because it is turning off to fast to detect.

Discussion of hacked phones is prohibited on these forums. Sorry, you'll need to go elsewhere to get support for a j'broke iPhone.

One question about Pricing and Conditions puzzle me for a long time!

One question about Pricing and Conditions puzzle me for a long time.I take one example to explain my question:
1-First,my sale order use pricing procedure RVAA01.
2-Next,the pricing procedure RVAA01 have some condition type,such as EK01(Actual Costs),PR00(Price)....,and so on.
3-Next,the condition type PR00 define the Access Sequences PR00 as it's Access Sequences.
4-Next,the Access Sequences PR00 have some Condition tables,such as:
     table 118 : "Empties" Prices (Material-Dependent)
     table 5 : Customer/Material
     table 6 : Price List Type/Currency/Material
     table 4 : Material
5-Next,I need to maintain Condition tables's Records.Such as the table 5(Customer/Material).I guess the sap would supply one screen for me to input the data of table 5.At this screen,the sap would ask me to select one table,such as table 5.When I select the table 5,the sap would go to the screen to let me input the data of table 5.But when I use the T-CODE VK31 or VK32 to maintain Condition tables's Record,I found it's total different from my guess:
A-First,I can not found one place for me to open the table,such as table 5,to let me input the data?
B-Second,For example,when I select the VK31->Discounts/Surcharges->By Customer/Material,the sap show the grid view at the right side.At the each line of the grid view,you need to select the Condition Type at the first field.And this make me confused very much.Why the sap need me to select one Condition Type but not the Condition table?To the normal logic,it ought not to select Condition table but not the Condition Type!
Dear all,I'm a new one in sd.May be this is a very stupid question.But it did puzzle me for a long time.If any one can explain this question in detail and let me understand the concept,I will appreciate him/her very much.Thank you.

Hi,
You said that you are using the T.codes VK31 or VK32.
These transaction codes are used to enter condition records for standard condition types. As you can see a grid left side having all the standard condition types like price, discounts, taxes, frieghts.
Pl check using T.code VK11 OR VK12 (change mode)
Here you can enter the required condition type, in the intial screen. (like PR00, MWST, K004, K005 .....etc)
After giving the condition type, press enter or click on Combinations icon on top of the screen. Then you can see all the condition tables which you maintained for that condition type. Like as you said table 118, table 5, table 6 and table 4.
You can select any table and press enter, then you can go into the screen in which you have all the field cataglogues you maintained for that table. For example you selected combination of Customer/Material (table 5) then after you press enter then you can see customer field on top, and material fields.
You can give all the required values and save the conditon record.
Hope this is clear.
REWARD IF HELPFUL.
Regards,
praveen

Ask a question about GUP

recently i designed a voice over ip , about 40 GW, 2 GK,all are 26 routers, i want to implement GK redundancy, i can use alternate method to config GK, but i want to use Cluster using GUP protocol, but we haven't used GUP before. i asked many person, they don't use yet.
i want to ask a question
are there any successful H.323 network using GUP.
and how about it, reliable or smooth,
thanks!
jack

GUP provides the following benefits:
1) Sharing the load across several GKs
2) Any single GK in the cluster can resolve an address for another member in the cluster
3) You can cluster up to 5 GKs in a cluster to address redundancy and scaling requirements
GUP is not suitable in an environment where a large number of endpoints are registered.

I want to ask a question but is it supposed to go in this "Ask Your Question" field or should this really be a synopsis or a tersely worded teaser, like a "subject" line?

Oh.
When I pushed the "Ask your question of the community" I got this empty box. But I've already asked my question. Should I copy and paste it into this box?
> I want to ask a question but is it supposed to go in this "Ask Your Question" field or should this really be a synopsis or a tersely worded teaser, like a "subject" line?<
There. Now I have asked the same question, which is of questionable value, for sure, twice. So, if someone answers it, they will get twice the points. Right? Or is there another box for that? Should I paste the question into another box? Twice?
I've been around here for a l-o-n-g time, longer than ol' BenB by several years, so you'd think I'd know better.
Maybe I do.
bogiesan
Message was edited by: David Bogie Chq-1, I blame all misspellings on my iPad's virtual keyboard.

Don't you have a deadline?
Oh, sorry, I thought this was an URGENT query because you have clients waiting.
Keep calm, carry on.

HT1937 I want to ask you question please i have free apple id because i am still a college boy who doesn't have any of credit visa card and i just want to download beautiful apps on my phone including whats app but they require payment information to comp

I want to ask you question please i have free apple id because i am still a college boy who doesn't have any of credit visa card and i just want to download beautiful apps on my phone including whats app but they require payment information to complete my request so please help me and please find a solution for this problem because not everyone have credit or master card .

Buy an iTunes gift card.
http://www.apple.com/support/itunes/cards-codes/

Where Would be the best category to ask a question about using dashboard?

Where Would be the best category to ask a question about using dashboard?

However, don't ask it in this topic. Create a new topic for the question with a title describing that you are looking for Dashboard help.

HT3702 Hi I would like to ask a question about my billing for some things

I would like to ask a question about my billing

This is not Apple. These are user forums. Questions about billing, credit cards, etc. should be addressed directly to Apple.
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support visit online support site.
For Mac App Store: Mac App Store Customer Service.
For iTunes: Apple Support for iTunes - Contact Us

Hi , i'm new here and i would like to ask a question about iPad 2 . Well , actually when i hold my finger on any icon , its not jiggling , i need to fix the icons . May i know what can i do in this case ? thank you in advance ,

Hi , i'm new here and i would like to ask a question about iPad 2 . Well , actually when i hold my finger on any icon , its not jiggling , i need to fix the icons . May i know what can i do in this case ? thank you in advance ,

Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider.

HI,I want to ask one question about SRP 521W

Similar Messages

Maybe you are looking for