Hi there, I need help .. I have 2 gen ipod touch and I restore my ipod around 11:00 pm and now its 1:20 am and on my screen its the iTunes logo and the usb cord and when I plug my charger in my laptop .. iTunes comes up and this what it saids "iTunes has
hi there, I need help .. I have 2 gen ipod touch and I restore my ipod around 11:00 pm and now its 1:20 am and on my screen its the iTunes logo and the usb cord and when I plug my charger in my laptop .. iTunes comes up and this what it saids "iTunes has detected an ipod recovery mode. you must restore this ipod before it can be used with iTunes" so what do I do.. do I let my ipod died right out & then try it .. because I restore it ,... it was beening to slow... so please help me ?
Maybe:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Then try restoring on another computer.
Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
Similar Messages
-
My iPod shuffle is not being recognized by my computer. It is flashing orange and when plugged in with the original USB cable nothing happens to show the computer recognizes it.
Flashing orange usually means it is being recognized by the computer. The flashing means do not disconnected, because the shuffle's "disk" is mounted.
In iTunes (with the shuffle connected), when you look in the sidebar (left side of window), under DEVICES, the iPod is not shown there? Does it say DEVICES in the sidebar? -
Pleae help, getting frusterated
When you find out the answer let me know cuz I'm having the same problem and they're telling me that maybe it's because of iTunes being down. Not sure tho
-
I have an old iphone that I've replaced with a newer one :-) and I'd like to use the old one in the same way I do an itouch. When I plug it into my Mac laptop, there is no recognition of it as a device. Help! What do I do????
http://support.apple.com/kb/ht3406
-
Hi everyone! I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer, so I can't put it in recovery mode or someting like that... What can I do?? I tried everything they tell me to do in the apple support but nothing seems to work. Thank you!
No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine. -
i bought the iPad and got it home and when I turned it on, all I see is the iTunes logo w/ a usb connector and arrow. How do I clear that and go to the home screen??? HELP!
You need to Set Up the iPad... Connect it to iTunes...
See here for Getting Started...
http://www.apple.com/support/ipad/
and here...
iPad User Guide iOS 5
http://manuals.info.apple.com/en_US/ipad_user_guide.pdf -
I have upgraded my iPod touch and it didnt respond to the upgrade. Cant remember which iOS i was upgrading but when i try to switch it on the apple logo comes up but than it just goes to the loading logo until the battery life is gone. I have tried restarting it , that doesnt work. I need help i am lost without my ipod please help. Any ideas besides restarting it ?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Tried to upgrading ipad 1 from itunes and l guess it did not complete the process because all I have showing on the ipad is the itunes logo with the usb cable. When l try to connect it to my system, it resquest that a driver be used to install the device. Please help! How do I restore?
Restoration is relatively simplistic. Here's whatcha do. Plug your ipad in, open itunes, now if itunes doesn't recognize it then you may have a problem, anywho, click on the ipad in the devices interface and go to the info tab, click restore, and it'll be just like it was when it left the factory. To get you data back, it should ask if you would like to use a backup, just select the backup you want and you'll be good to go. That is if you regularly backed up your iPad.
-
My ipod nano 6th gen doesn't start. When I plug it, only blink the apple logo on the screen. I try to reset it holding by 8 seconds start button and volume down and doesn't work. My Ipod doesn't have any shock or water damage. How can I do?
Hey rulosrojos,
The article linked below details a number of troubleshooting steps that can help restore functionality to your iPod nano.
iPod nano (6th generation): Hardware troubleshooting
https://support.apple.com/en-us/TS3474
Sincerely,
Allen -
I can't open my ipad now. It is stuck with the picture of the usb cord and the itunes logo on the front.
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times. -
i bought a iphone 3g from market yesterday and the phone is showing a usb an also itunes logo on the screen, the ive tryed restore and update, but once this has finished it gives me erra code (1015) can anybody help me plz
Error 1015: This error is typically caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple. This error can also occur when an unauthorized modification of the iOS has occurred and you are now trying to restore to an authorized, default state.
http://support.apple.com/kb/TS3694#error1015. -
I tried to update my sons ipod. It has the itunes logo with a usb port on the screen. If I restore it I will loose all his games and music. Is there any way around this?? Please Help??
Yes, that is your only option.Yes. You have to restore.
Try the following if you have difficulty restoring.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Bought a new macbook and want to manually manage music onto my iphone 4s (as it is already full of music from old windows laptop) but when i click 'manually manage' and then 'apply' i get the message saying it will erase everything already on there. Need help please!
Before you sync your iPhone make sure that all the music that was synced to your phonereviously has been copied to your iTunes on the new MacBook Pro. Then when you connect your phone you will be able to either sync all music or select only those playlists that you want on the phone.
-
hello i have a trouble with my i phone... i was trying to update a new software and at the end it says that there is some error and i cannot turn my i phone bak on all it shows is itunes logo in the midlle and usb cable with an arrow pointing at the logo. If anyone knows what it is and what i should do please get back to me as soon as possible many thanks.
http://support.apple.com/kb/HT1808
-
my ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else. It won't switch on beyond that. Please help!
Sounds like your iPod is in restore mode. Connect it to iTunes. iTunes will pop a little message up saying that your iPod is in restore mode and asking you if you want to restore it, click yes. Your iPod will restore to factory settings and you will be given the chance to restore from a backup. You can do this or set it up as a new iPod.
Here is Apple's page on restoring your iPod.
http://support.apple.com/kb/ht1414
Hope that helps.
Maybe you are looking for
-
How-to (easily) retrieve the ColorSpace at the page level
Hello, I'm lloking for a method to (easily) retrieve the ColorSpace at the page level. Actually in my PDF there are ColorSpace at page level and also at element level. Moreover what is the behavior when there are more than one ColorSpace. Is it the C
-
Trouble with locked/read only files and folders
After reinstalling OSX I have an external harddrive with locked files and folders. I´ve heard that it is possible to unlock all files and folders from Terminal (it will take hours to unlock manually). Anyone who knows a script that will set read and
-
Hey everyone! I'm at your mercy! Desktop version won't redirect to phone app.
OK. I'm tired. I designed a site www.aliciastecklercounseling.com for the first time in MUSE. For the phone design I designed a temporary site just giving vital information on how to contact her. Stayed up all night designing the site, worked on
-
Javax.microedition.location does not exist
Hello everyone. I am new to J2ME development and having problems trying to compile some code. Here's the error message I keep getting: package javax.microedition.location does not exist import javax.microedition.location.*; I really don't know how to
-
Hi. I want to go wireless, I am running on OSX 10.5.8. is there a specific card I need?