Hi there , Why Do I Receive Error Code -1073807253 When Using VISA

Error Code -1073807253

Hi ahmed,
you can attach picture directly in the forum...
If you would use an error indicator you could read an explanation of the error. It's a "framing error", happening sometimes when using serial connections...
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Similar Messages

I receive Error code: ssl_error_unsafe_negotiation when I visit any secure site version 3.613

I receive Error code: ssl_error_unsafe_negotiation when I visit any secure site using version 3.613.
I can browse to all of these sites successfully using IE 8.0.6

See this link for information about 'Renegotiation' (CVE-2009-3555):
* http://wiki.mozilla.org/Security:Renegotiation
* https://wiki.mozilla.org/Security:Renegotiation#security.ssl.renego_unrestricted_hosts
You can look at the pref security.ssl.renego_unrestricted_hosts on the about:config page and add the sites that you want to allow to the string value. 
Separate multiple host names by a comma.
To open the about:config page, type about:config in the location (address) bar and press the "Enter" key, just like you type the url of a website to open a website. 
If you see a warning then you can confirm that you want to access that page. 
You can use the Filter bar at to top of the about:config page to locate a pref more easily.

Why do I receive error code "-1074118644" when trying to initialize the 2532 Matrix?

I am using the VI "IviSwtch Initialize With Options.vi". I created a logical IVI name (MATRIX), and am passing the following option string: "Simulate=0,RangeCheck=1,QueryInstrStatus=0,Cache=1,DriverSetup=Topology:2532/1-Wire 4x128 Matrix". I tried variations of this with no luck. I configured the matrix in MAX with the same topology as shown above. My software versions are:
IVI Compliance package 2.1.2
LabVIEW 7.1
NI-SWITCH 2.30.49153
VISA 3.1
NI-DAQ 7.3

Thanks for the response Greg. I did finally get it working, but I had to use the "PXI1Slot8" format for the resource descriptor rather than "PXI2::9::INSTR". I don't know if that is typically what you are supposed to do, but that cleared the error.
To answer your questions, there's only one 2532 in the system. There is a 2566 in there as well. The configuration I was referring to was the IVI Driver configuration in MAX, not the DAQmx configuration, although I did select the TB-2640 under the DAQmx configuration, so it did default to the 1-Wire, 4x128 matrix as well.

TS3694 Why am I getting error code 3194 when i try to restore my ipod?

Why am I getting error code 3194 when I try to restore my ipod touch 4th generation

This device is not eligible for the requested build: Also sometimes displayed as an "error 3194." If you receive this alert, update to the latest version of iTunes. Third-party security software or router security settings can also cause this issue. To resolve this, follow Troubleshooting security software issues.
Downgrading to a previous version of iOS is not supported. If you have installed software to perform unauthorized modifications to your iOS device, that software may have redirected connections to the update server (gs.apple.com) within the Hosts file. First you must uninstall the unauthorized modification software from the computer, then edit out the "gs.apple.com" redirect from the hosts file, and then restart the computer for the host file changes to take affect. For steps to edit the Hosts file and allow iTunes to communicate with the update server, see iTunes: Troubleshooting iTunes Store on your computer, iPhone, iPad, or iPod—follow steps under the heading Blocked by configuration (Mac OS X / Windows) > Rebuild network information > The hosts file may also be blocking the iTunes Store. If you do not uninstall the unauthorized modification software prior to editing the hosts file, that software may automatically modify the hosts file again on restart. Also, using an older or modified .ipsw file can cause this issue. Try moving the current .ipsw file, or try restoring in a new user to ensure that iTunes downloads a new .ipsw.
Error 3194: Resolve error 3194 by updating to the latest version of iTunes. "This device is not eligible for the requested build" in the updater logs confirms this is the root of the issue. For more Error 3194 steps see: This device is not eligible for the requested build above.
http://support.apple.com/kb/TS3694#error3194
Also see:
iPhone Error 3194 - How to Fix iTunes Error 3194?

Why am I getting error code 1402 when trying to update adobe reader 10?

Why am I getting error code 1402 when trying to update adobe reader 10?

Impossible to guess the "why" with so little information, but this may be helpful if you want to solve the problem: Error 1402 | Error 1406 | Acrobat, Reader

HT1925 I receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

It's a better bet with a 2330, but the first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

On Adobe Acrobat Pro X "I received error code 2148073483 when trying to sign my documents. I am using Windows 8.2"

Using Adobe Acrobat Pro X I received error code 2148073483 when trying to sign my documents. I am using Windows 8.2.

Please read, and reply back here with information https://forums.adobe.com/thread/1499014
-try some steps such as changing browsers and turning off your firewall
-also flush your browser cache so you are starting with a fresh browser
http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip/
http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html
or
A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

I received error code (-50) when trying to restore my iPad. Does anyone know what this error code means?

I received error code (-50) when restoring my iPad2. Does anyone know what this error code means and how to fix it?

See the More Like This Section on the right...

Why do i get error code 0x80020063 when burning pics to CD in Finder? Burns from iTunes fine

Why do i get error code 0x80020063 when burning pics to CD in Finder? Burns from iTunes fine

Hey Ken 17,
Thanks for the question. I understand that you are experiencing issues burning a disc in Finder. The following resource may provide a solution:
OS X Mavericks: If you have trouble burning discs
http://support.apple.com/kb/PH13990
Thanks,
Matt M.

Why do I receive Error Code -50000?

I have a M-serie 6221 card where I use the two analog output, DC voltage out. (Labview 7.0 running on a Pentium 4 HT processor and Win XP SP2).
I have two processes (independant dynamic VI's) for analog voltage output.
Process 0 use AO channel 0 and Process 1 use AO channel 1 on the 6221 card.
Both processes use the simple DAQ-Write 1 Chl 1 Smpl VI and with an update rate of only 4 Hertz.
I have made shure that the data input is between +- 10V using a coerce function.
Occationaly (sometimes hours between fails) I receive Error Code -50000 (=conflicting parameters) after one of the DAQ-Write 1 Chl 1 Smpl VI .
Why?
Can it be a problem with multi-threading?
Regards
Bo Hellman
Biotage Sweden AB

bohellman,
When you are using the DAQmx Write VI, are you setting the auto start input to false, or have you left it at its default of true. One thing I would recommend trying is to explicity start the task and set auto start to false, and see if this makes any difference. If you are writing within a loop, then this can also make your application run more efficiently.
To determine if the problem was a multithreading issue, you could disable multithreading within LabVIEW (Tools-Options, select Performance and Disk tab).
If you still have trouble, could you post the problematic portion of your VI that is causing the error?
Good luck,
Jason

Why do i get error code 1935 when installing light room 5.4?

Does any one know why i get this error code when installing light room with my HP deske top with windows 8.1? error code 1935

Error code -35 means "No such volume; volume not found". Not terribly helpful.
You have already tried everything I would have suggested. Maybe someone else will have some suggestions?

Why do i get error code 205 when trying to download

why do i get error code 205

Error 205 indicates that your downloaded installation file became corrupted. Please try an alternate Internet connection. If you are connected by wireless try a wired connection. If you are connected via a wired connection try a different cable.
Please try an alternate Internet browser and disable anti-virus and turn-off firewall during download.
https://creative.adobe.com/products/creative-cloud
Prior to these please go through : Error downloading Creative Cloud applications
This might be also useful:
Re: Installing Creative Cloud-Error 205
Regards
Rajshree

At first error code 205, Error code 1 when using new user profile

Hi,
I'm using Windows Professional 8.1 with CS6 installed.
I now decided for CC, but as many other users I'm not even able to install it!
On my admin account I get the error code 205 when trying to launch CreativeCloudSet-Up.exe.
I read lots of similar posts and tried everything I found, e.g. creating a new Windows admin user profile - this broughtt me just one step further as the installers quits a little bit later with another error code (1).
My PC is a Quad CPU with 2.4GHz, 8GB of RAM and a 512GB SSD - so technical limitations (as I figured out might be indicated by error code 1) shouldn't be an issue!
And it is not even possible to drop an Email to Adobe Support as there is only chat and phone from Mo-Fr 9-17h - this is ridiculous...
Anyway - why are there no more simple Download-Links for the Apps?
Obviously Adobe seems not to be able to provide working installers - this whole CC thing is absolutely crap as I'm not able to use it!
I'd really appreciate if someone who had/has the same problem(s) would come up with a solution - and please - no standard links to dummy Adobe support pages!
Thanks a lot in advance and best regards
Carsten

Error 205 is an network connectivity issue.
I guess you getting error message as "Installer Failed -Download appears to be corrupted (-60) "
The recommend solutions are provided in the below link :
https://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html
Tips:
1)If you are using Wireless/Wifi Internet , try with Ethernet wired connection .
2)Disable FIrewall, if you are on office or managed corporate network, if it is not possible to disable Network FIrewall , try Adding ports list to network firewall Allow/Whitelist.
3)Check whether the LAN settings is set to detect settings Automatically.
4)Try with different Internet connection , possibly different Internet Service Provider.
If face same issue even using different Internet Service Provider connection , you may contact Adobe Support and inform them regarding the issue.
Because , it will be necessary to check log files like PDAPP , OOBELIB...etc
However , for time being , it is smart to install and use the Apps using alternative method .
There is a direct download links for all CC apps .
http://prodesigntools.com/adobe-cc-2014-direct-download-links.html
let me know if you need any help
Let me know if you are office network or any managed network , I will provide you list of Adobe ports .

TS3694 Received error code 3194 when trying to restore my daughter's ipod. Why and what do I do now?

When trying to restore my daughter's ipod touch (because she forgot her password), it keeps giving me error code 3194, Does anyone know why and what I'm supposed to do next? Thanks!

Here:
iTunes: Specific update-and-restore error messages and advanced troubleshooting
or
iPhone Error 3194 - How to Fix iTunes Error 3194?
or
Fix Error 3194 from iTunes during iPhone restore

I keep receiving error code U44M1i210 when updating CC products since yesterday

All my CC products are returning me the same error code when I try to update since the 12th Jan. This is the full message for Dreamweaver: "There was an error installing this update. Please quit and try again later. Error Code: U44M1I210
Dreamweaver CC Release – December 2013".
I have tried via the individual product, Help, Update....it still doesn't work.
I have reported via Online Chat - they told me I needed to call the helpdesk team. I waited 33 minutes and hang up as I was fed up with waiting - please help.

I have found a solution that worked for me. The PC that I was trying to update kept failing no matter what solution I tried. Each time I tried to update, the progress bar would always start at 51%. Telling me that the download was done and that the problem lied either with the files themselves or the ability to extract them properly.
I asssumed these bad files were held somewhere in my Windows User Profile. So, I logged on as a different user and this time the Updater started at 0% telling me that I was getting a fresh download.
So far, I have been successful updating through the application itself - Help menu... Updates... and through the CC Desktop application.
I still do not know what is wrong per se, but I do know that by logging in a different user, I was able to get a clean download and a successful update.

Hi there , Why Do I Receive Error Code -1073807253 When Using VISA

Similar Messages

Maybe you are looking for