HI, want to connect XI and Mobile

hi,
Experts,
I am new to mobile world.
can you please tell me how to connect Mobile and XI.
I want to know the flow between Mobile and XI, how data will go?
I have heard about mobile gateway, what is it?
What changes I have to make in XI server to support Mobile connectivity?
Thanks.
Waiting for replies..

Hi divyesh vasani,
Welcome to Mobile Infrastructure... you can easily get along with MI by just following some of the links below:
  - what is mobile infrastructure?
  -Mobile--XI--R/3
2. R/3 Gateway for mobile
Document for Data Flow between Mobile and XI is a very good Document for understanding <a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/ceb31d4f-0901-0010-60bc-8162e7c6179d">Integrating Mobile Device With SAP XI</a>
PS: <b><i>Do Reward points if this helps you...</i></b>
Cheers,
kumarR

Similar Messages

  • Connect pc and mobil though com port

    I want to connect pc and mobil.But i don't have set command commapi to connect them.Can you give that ?
    Thanks a lot.

    You mean the jar file?

  • Small configure help please? I have 3 300-28 switches, I want to connect them and avoid stp (stp setup)

    HI!
    I have a small network. I have 3 300-28 cisco switches. I already connected my 3 servers  and clients with the switch 1 and now I want to add more clients and I need to add my other two switches in the network. Please guide me with the simple configuration So I can connect them all and avoid loop (stp). Thanks

    Hi Nagaraja Thanthry!
    Thanks for your reply. I am implementing it tomorrow. By just conecting the switches together at trunk ports  will there be no loop? I don't want my network chowk. I hope it will work well. I might need further help, please reply.
    1. I will do setting on all switches. Assign IP addresses to switches (to Vlan 1 default).
    2. Set one port (e.g 28) as trunk and all others as Access on all three switches.
    3. Then I will connect the switches with each other at trunk ports. Hope there will be no loop in this setting.
    4. Do I need to set any setting for stp in switches ?
    Please reply one by one thanks.
    I am using 192.168.0.1 255.255.255.0 IP range.
    Best Regards,

  • Possibility to route Sound? (connect headphone and speakers at the same ti

    Hi is it possible to route the sound of my X-FI Titanium (PCIe)?
    I want to connect Headphone and 2. Speakers at the same time and want to be able to decide where the sound comes out.
    It wasnt possible with my previous audigy 2zs, but it thought now it could be possible, because every cheap onboard sound can do that.
    The only solution so far was to choose stereo surround but that wont work in games because most games recognise 4 speakers and some sound is missing.
    Any hints?
    Thanks in Advance

    I used to be able to do that in XP with an SB Li've 024 which?was like 2+2 stereo card before 5. came out.
    Thinking....maybe somethig like [url="http://www.pccables.com/images/05004.jpg">this[/url]?(3.5mm STEREO JACK Y-SPLITTER ADAPTER) plugged into front out for headphones and front speakers.
    You can also get a cable that does similar.

  • PDA and Mobile

    hi all
    One of our client want to develop application using Forms and reports and keeing them on application server on intranet. the data in the application is real time data. He want to use PDACS and Mobile to view the alerts and data from the database. Does any one did similar work... is so can u share how ??

    Forms does not run on those devices (PDAs or other mobile devices). You should ask your question on another forum. Try the iAS forum.
    Regards,
    Robin Zimmermann
    Forms Product Management

  • I just got an apple at&t iphone 4 and I have it unlocked. But I want to connect it to t-mobile, so I trimmed my sim card and once the phone was unlocked I inserted the sim and it says no sim, activation error. What can I do to fix this? What is wrong?

    I just got an apple at&t iphone 4 and I have it unlocked. But I want to connect it to t-mobile, so I trimmed my sim card and once the phone was unlocked I inserted the sim and it says no sim, activation error. What can I do to fix this? What is wrong?

    JayleneC wrote:
    Wait.. Everything on iTunes worked, but when I insert my sim it brings me to the start were I have to choose my language, etc... Then it says activation error.. Are you sure it's the sim card?
    As you addressed me that is exactly what I said
    Dodgy trimming ??   get a new micro sim from T-Mobile

  • Jabber and Mobile Connect

    Just setup Jabber (9.0.2) on iphone with Mobile Connect (CUCM 7.1.5). I run into incoming call issue where both Jabber & mobile phone would rings about the same time. I did some of research and Cisco doco below state Mobile Connect should automatically inactivated when Jabber is running and connected to the corporate network.
    Anyone has this issue or could point me to the right direction?
    http://www.cisco.com/en/US/docs/voice_ip_comm/jabber/iPhone/9.0/JABI_BK_J29330BB_00_jabber-for-iphone-admin-guide_chapter_011.html#CJAB_TK_ADA0EB97_00
    Add Mobile Connect and Mobile Identity
    Mobile Connect, formerly known as Single Number Reach (SNR), allows the native mobile phone number to ring when someone calls the office number while Cisco Jabber is not available.
    When Cisco Jabber is running and connected to the corporate network, and thus available to receive VoIP calls, Mobile Connect is automatically inactivated.
    The user requires a Mobile Identity to transfer Cisco Jabber VoIP calls to the mobile voice network.

    Remote Destinations will always ring, regardless of whether the TCT device is registered or not. A Mobile Identity will not ring when the TCT device is registered to CUCM. This is especially important as you don't want the cellular phone and the wifi phone app contending for the user to click answer on both on the same device. You may still want to use RDP if the user has a home office in addition to their smartphone.

  • I want to connect my ipad mini to my Apple TV. There isn't a option when I double tap on my ipad button for connecting to the tv and I also can't connect to home sharing from my iTunes settings. Can someone talk to me in simple terms. Thanks

    So I have a ipad min. I want to connect it to my Apple TV. There is no option on my ipad for home sharing which my Apple TV is telling me to do.
    Can somebody please just explain it to me in simple terms where I can find the home sharing and what I have to do to connect my Apple TV to the ipad or vice versa.
    Everything I have bought from apple in the past month has been a complete let down its taking far to long to connect things and the people who sell the products to you lie about what the product does and can do.
    Can someone help me please
    Thanks

    AirPlay isn't anything to do with homesharing. (Home sharing lets you share the iTunes libraries on computers)
    Basic AirPlay: Assuming both devices are on the same network and that AirPlay is not turned off on the Apple TV, then simply tap on the screen when you are watching content you wish to stream to your Apple TV, then tap the airplay icon that appears in the control bar, choose the Apple TV from the menu that appears.
    Mirroring: When displaying the content you wish to mirror on the iPad 2 (or better), iPad Mini, iPhone 4S (or better), double tap the home button (quickly) and swipe the bottom row of apps to the right to reveal the playback controls, tap the AirPlay icon and select your Apple TV from the list of available devices.
    Try the following steps, check whether things are working after each step where appropriate, before trying the next.
    Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
    Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
    Restart the Apple TV (Settings > General > Restart).
    Restart the Apple TV by removing ALL the cables for 30 seconds.
    Restart your router.
    Restart your mobile device.

  • Want to connect internet mobile to another via blu...

    Hellow fellows:
                         Can any one tell me how i connect my other mobile phones of nokia with my 5530 Xm for internet via bluetooth
    i am using internet in 5530 via wifi
    plz tell me any application or any thing?? 

    OK, I see what you want.
    I'm afraid it can't be done. Your 5530 cannot act as a bridge between bluetooth and a wireless internet connection. If you try and use it as a modem over a bluetooth connection it will connect to the internet using your operator's packet data service and channel that over bluetooth, not the connection already established via the WLAN.
    Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

  • Remote Desktop Connection between Windows Mobile 6.5 and server 2012

    Hi all,
    We have problem with remote desktop connection. The server that I want to connect is 2012 R2.
    We have no trouble with server 2008. I searched from internet, there are solutions on server side(I am not sure if these suggestions solve the problem), but our customers don’t want to solve this problem
    on server side because it is diffucult and risky.
    Is there a solution on handheld terminal side to do?
    Operating system: WM 6.5 classic(Professional o.s. has no effect, same error continues)
    Any help will be appreciated from your side.
    With Best Regards.

    Hi,
    What is the precise error message you are seeing?  What are the exact symptoms?
    I don't remember what version of RDP/featureset is supported by Windows Mobile 6.5.  Perhaps the client does not support Network Level Authentication, which is required by default on Server 2012 R2.  You can enable non-NLA connections by
    unchecking Allow connections only from computers with Network Level Authentication in Server Manager -- RDS -- Collections -- Properties of collection -- Security tab.
    Lack of NLA may not be the cause of the issue you are experiencing, however, if it is the only way to solve it would be to change the server setting or to potentially install a new client on the device that supports NLA.
    -TP

  • I just bought a panasonic  50" plasma tv model TC-P50X3 and i want to connect my macbook pro with my new ty how do i do that?

    i just bought a panasonic  50" plasma tv model TC-P50X3 and i want to connect my macbook pro with my new ty how do i do that?

    Assuming your MBP is a recent model, i.e. bought in the last couple of years, and that your TV has HDMI inputs (if you've bought it new then that's a safe assumption) then you need a mini-displayport to HDMI cable.  The Apple Store sell one:
    http://store.apple.com/uk/product/H7128ZM/A/mini-displayport-to-hdmi-cable-2m?fn ode=MTY1NDA3Ng&s=topSellers

  • I have a macbook pro with lion os. and i want to connect it to my optoma dlp projector. when i connect through a mini display to vga adapter in MBP it detects as OPTOMA XGA but no image on the screen.

    i have a macbook pro. i want to connect it to projector and i have a minidisplay to vga adapter. i could connect my MBP to benq projector successfully and for  all other displays( Monitors). but when i connect it to optoma projector, MBP detects the display as OPTOMA XGA but nothing on bigger screen. i tried changing the resolution and refresh rate also but no changes.
    In my office we got benq projectors , for that it is working very well.(plug and play).
    and also i want to say that there is no problem with the optoma projector seems, because all other windows laptops are working well with that.
    i was struggling with this since one month. i googled it could not find anything supportive for my problem. please help me regarding this. i am new to apple. i hope there must be genius around here.
    thnak you

    Rwogera wrote:
    I couldn't transmit sound either, do i need another cable like Kim said? i mean it cant be transmitted through this HDMI port? as for me i have one of the latest mac pro with intel core i5..tnx
    I need to know which MacBook Pro you have.  Only mid-2010  and later MBP's transmit sound through MiniDisplay Port to HDMI.  I have no information about the Mac Pro, so you might want to go to that Forum and ask there.

  • I want to connect my IMAC to TV with HDMI cable. I did it before going to Dispaly and Arrangments and then mirror. Now when I go to display I dont have to option of arrangements. Olny {Display and Color} pops up. Any ideas what happend to arrengements?

    I want to connect my IMAC to TV with HDMI cable. I did it before going to Dispaly and Arrangments and then mirror. Now when I go to display I dont have to option of arrangements. Olny {Display and Color} pops up. Any ideas what happend to arrengements?

    For the "Arangements" option to appear, the external display must be turned on with the correct input selected and connected to the computer.  Then close system prefs, reopen, go to "Display" and "Arrangement" will be along the top. 

  • HT4946 i got my new iPhone 5 and i connected it to my iTunes on mac and it ask me if i want to setup as new iPhone or restore backup and i restore back up but now i want to delete backup and set up as new iPhone, is the anyhow?

    i got my new iPhone 5 and i connected it to my iTunes on mac and it ask me if i want to setup as new iPhone or restore backup and i restore back up but now i want to delete backup and set up as new iPhone, is the anyhow?

    The iCloud backup includes most things except non-iTunes purchased but the iTunes backup does not include those either. For what iCloud includes see:
    iCloud: iCloud storage and backup overview

  • HT4859 I have an iPhone 5 and have just set up the iCloud for it. I also have an iPad with different content and I also want to connect it to iCloud. Will I lose everything that's on my iPad or iPhone or do they sync together without losing anything?

    I have an iPhone 5 and have just set up the iCloud for it. I also have an iPad with different content and I also want to connect it to iCloud. Will I lose everything that's on my iPad or iPhone or do they sync together without losing anything?

    The problem is that all services are bundled with your Apple ID ([email protected]):
    Your iCloud account (Mail, Contacts, Calendars, Reminders, Notes, Backups, etc.),
    also iTunes & App Store purchases (Music, Movies, TV Shows, etc.),
    and the iTunes Match services.
    (I guess that all your devices - yours and your wife's are connected to one iTunes library, right?)
    If you want that your wife gets her own iCloud account for Mail, Contacts, Calendars, etc. but gets also access to your media then you have two set up two things on her device:
    iCloud (Settings > iCloud) with her account (e.g. [email protected])
    and
    iTunes & App Stores (Settings > iTunes & App Stores) with your account (e.g. [email protected]).
    In this case she gets access to your library and could use the same iTunes Match account.
    (See also: Using one Apple ID for iCloud and a different Apple ID for Store Purchases http://support.apple.com/kb/HT4895)

Maybe you are looking for

  • I have problem with deployment of my customised module in oracle applications

    Hai, I have started working with oracle application just recently as I started to customise Forms & Reports. If I am developing forms and reports from the existing modules it is working fine. But as we can develop our own customized module in oracle

  • PO document number is not displaying.

    Dear Friends, I created purchase requistion in Tr code ME51N ,after that ,aganist this PR No we have created PO. But now we are not able to display this PO No in ME53N. whereas i checked table also EKKO,EKPO is not updated. It is only seen in Tr code

  • Getting present display records  or Row Id's information in ALV grid?

    Hi, I am using REUSE_ALV_GRID_DISPLAY for ALV display. I need to get the row id's when user filter the records with any conditions  - or any other ways if he selected particular records - I need to process my logic only for those present displaying r

  • Connect MBP to HDTV problem..

    So I connected my MBP to HDTV through a MiniDisplayPort to DVI <-> DVI to HDMI cable, and all I can see is my MBP wallpaper on my HDTV. I haven't changed any options so I figure that's the problem, but I've been looking online and on my computer for

  • Error at Draft Invoice

    Invoice rejected in oracle the reason for rejection is invoice line with the same invoice number have been separated by the grouping process, causing duplicate invoice number.