Hi, what does the Error Code 4sns/1/40000000:IDOR-6.188 mean?

hi to everyone
A friend of mine has a Mac Book pro. Several days ago it wouldn't start up any more. It just goes on, then clicks and goes off. The only possibility was to press and hold the Power Button. After this procedure the MacBook booted up but was very slow. The cursor hangs etc.
I was able to do an extended diagnostic test and got the following error:
4sns/1/40000000:IDOR-6.188
I found some messages regarding hdd via google but the hadn't any value for me.
Best regards,
Nico

I ran the hardware test on my MacBook unibody and got the same result. Did you ever get an answer as to what this code means? I haven't been able to Google it either.

Similar Messages

  • What does AHT error code 4SNS/1/40000000:TB1T-128.000 mean?

    My MacBook froze on me last night while running Firefox w/ 4 windows open, each with 6 or more tabs.  Seemed partly due to using the instant message ap on Facebook.  The machine forze with the beach ball spinning it's heart out.  Shut it down, restarted, and got a freeze during start up.  Tried again this morning and the machine seemed to run ok for a session, after which I closed the lid without shutting down.  After opeing the lid, the machine ran ok, then slow, then froze.  I eliminated peripheral problems, eliminated software problems, then ran an Apple Hardware Test.
    It produced the code:  4SNS/1/40000000:TB1T-128.00
    This code does not show up in Google or this forum.  Any idea what it means or where I may find out what it means?  It's a late 2008 MacBook, so no warranty whatsoever.
    Thanks in advance for any help!
    Kermit

    I ran the hardware test on my MacBook unibody and got the same result. Did you ever get an answer as to what this code means? I haven't been able to Google it either.

  • What does error code 4sns/1/40000001: IDOR-0.000 mean?

    I have a MacBook Pro modWhat does error code 4sns/1/40000001: IDOR-0.000 mean? My video display is partially striated and I ran the self test a few minutes ago.el 10,1 with an NVIDIA Ge ForceGT 650M graphics card with 1GB of VRAM.  When I turned on my laptop this morning the right 1/3 of the screen was black with red and multicolored lines, I had to reduce my window view to see the document I was looking at.  I rebooted several times and ran the hardware test recommended.  The results indicated an error, the code: 4sns/1/40000001: IDOR-0.000.  Can anyone decipher the code and tell me what is wrong?
    thanks

    That error code indicates a DC current anomaly.  A visit to an Apple store genius bar is your best option.  They should be able to specifically isolate the problem and and advise you of your options.
    Ciao.

  • What does the error code 0x80090318 mean connecting to IStore?

    What does the error code 0x80090318 mean connecting to IStore?

    I think the problem was using a WPA2 network rather than a WPA network. When I tried connecting to a WPA network, everything went fine.

  • What does the error message "Opening file in iCloud(state=5) mean?

    I have been ushing iCloud to backup my data for Ascendo DataVault for my iPhone 5 (iOS 7.0.4) and original iPad (iOS 5.1.1) very successfully for some time.  Both devices are synchronized with my PC using Wi-Fi.  The DataVault data on my PC is also synchronized on my wife's iPhone 5 (iOS 7.0.4) and iPad Mini (iOS 7.0.4).  Recently, every attempt to synchronize my iPhone or iPad with my iCloud results in the error message "Opening file in iCloud(state=5)," but my wife's iPhone and iPad continue to synchronize with her iCloud without any problems.  What does this error message mean, and is there a cure for the problem?

    OK found a solution!
    It is really lame!
    NEVER add a reminder in iCal dragging them into the Week or Day view!!!
    Change to Month view and then drag the reminder on the desired day!
    You can now change to Week or Day view and move the reminder to the selected hours.
    Please help share this solution and click like to get Apple to finally fix this issue, which is clearly on their side.
    Thank you

  • What does error code: 4SNS/1/40000000: tm0p -61.000 mean?

    I just dropped my MacBook Pro "17 i5 500GB 4G RAM (2010 Model) about 3 feet from a chair on to the floor of my house (hard wood flooring), unfortunately.
    Everything seems to work well but I went and did a hardware check, but Pressing "D" at startup, I got this error:
    4SNS/1/40000000: tm0p -61.000
    What does this mean?

    Thanks, I will try to take it to the Apple Genius Bar this week.
    And I have 3 more questions:
    How much will this sensor cost? is it expensive?
    Is it a serious issue? Because when I run the hardware test, it only gives me this error in the short test NOT extended test.

  • What does the error code -41004 mean in print report.vi?

    I am getting the following error in the Print report.vi.
    Error Code : -41004
    Error Scource : Print Report.viPrint_VI_Image.vi

    Hi
    I have attached the main vi which is using the NI-Print Report.vi.
    I have also attached the image of the error desciption I got.
    Attachments:
    OPG_Print_to_PDF.llb ‏94 KB
    error.bmp ‏273 KB

  • What does the error message 4sns/1/40000001:VCOR mean?

    My 17" intel iMac has recently decided to refuse to boot up. Whenever I try, I get a loop of partial chimes and blackness or a full chime, an apple screen with the spinning gear, then finally blackness. This is accompanied by ticking sometimes. I ran an apple hardware test and that's what I got. I have yet to find a post regarding the VCOR error, so if anyone knows I would really appreciate your help. If it helps, the code disappears immediately after a pmu reset until the next day
    Thanks!

    I'll request that this get moved out of the iPhone forum and into the appropriate one.

  • To what does G4 error code post16/4609 refer?

    to what does G4 error code post16/4609 refer?
    G4 MDD 1.42 PPC passes all hardware tests but gives post16/4609 error at start up.
    What does it mean?
    What is the resolution?

    I don't get any unhappy beeps.
    I get the chime. If I am not patient restarting I get high speed fan - I shut off be patience restart and get chime and search for drive then circle slash. hardware test gives me the master post 16 / 4609. - suggesting a bad drive according to other apple pundits. However, I have put two new 250GB WD drives in and still get a mass storage error. My G4 Mdd 1.42 supports drives 128GB+. I've replaced IDE cables and have master drive with out a jumper and have tried slave at CS and 3/4 slave setting all with the same result.
    Target boot got me to the "firewire drive" showed me one unformatted 250GB drive and I used disc utility to partition it according the PPC settings. Still same error.
    What gives?

  • HT203176 Does the error code "2STF/8/3.ATA-100ata-6-Master" means I have to replace my hard drive?

    Does the error code "2STF/8/3.ATA-100ata-6-Master" means I have to replace my hard drive?

    It is either a failing/failed hard drive, or a problem with the controller, which means logic board. If you Macbook is old enough to be running Tiger (which is what this forum covers) then the answer to your question is no, you need a new Mac!

  • HT201250 what does reported "error code 6584" mean ?

    What does reported "error code 6584" mean ? when trying to get into my time machine back up.

    First, I suggest you make another full backup to a locally-attached external hard drive. You should do that anyway. One backup isn't enough to be safe, and backing up over a network is less reliable than backing up locally. Then try each of the following steps that you haven't already taken.
    1. Restart the backup device. You can do that by disconnecting and reconnecting the power cord.
    2. Open the Time Machine pane in System Preferences and check that the device is selected as a destination. If it isn't, select it and try again.
    3. Hold down the option key and select Verify Backups from the TM menu in the menu bar (not the Dock icon.) This operation may take a long time. If the menu-bar icon (a clock that runs backwards) isn't showing, check Show Time Machine in menu bar in the preferences.
    4. Erase the backup device. With a Time Capsule, you do that from within the AirPort Utility application; see its built-in help for details. All backups on the device will be lost, so don't do this until you've backed up to another device. After erasing, select the device again as a backup destination in the TM preference pane. The first backup should be made over a wired connection, if possible.

  • HT1491 Why do i keep getting the message 'Cannot connect to iTunes Store' when I have done every connection I can find? What does the error message (-1202) mean when I am on the iTunes site on my computer?

    Why do i keep getting the message 'Cannot connect to iTunes Store' when I have done every connection I can find? What does the error message (-1202) mean when I am on the iTunes site on my computer?

    Hi Velvalee,
    While there may not be specific information about that error, here is an article of steps for troubleshooting connectivity issues with the iTunes store:
    Can't connect to the iTunes Store
    http://support.apple.com/kb/ts1368
    If that article does not help, there is a link near the bottom for an additional article of advanced troubleshooting.
    Cheers!
    - Ari

  • What does the error "Unable to lock the following files:" mean?

    What does the error "Unable to lock the following files:" mean? After the colon in this error message, a path to the .icml file is listed. We are using InDesign CS6 with InCopy CS6 (Mac), assignment-based workflow, on a shared server.
    Thanks,
    Gita M

    Sounds like a permissions issue on that server.
    Bob

  • HT2433 what does the error message that says " You are logged out because another computer is using this IP address." mean?

    what does the error message that says " You are logged out because another computer is using this IP address." mean?

    Some other piece of network ghardware on your home LAN (Local Area Network) is using the IP address your Mac is trying to use.
    Reboot both your modem and router, or the Modem/Router combo box you have, and all pieces of networking equipment, computers and printers, you have connected to your LAN.
    If you continue to get that error then it is a bug in OS X or you have your Mac set to a Static IP address that is being handed out by the routers DHCP server to some other device.

  • What is the error code mean? And how to solve it ?Please give your answer. Thanks

    What is the error code  mean? And how to solve it ？Please give your answer. Thanks
    Attachments:
    QQ截图20140403134626.png ‏59 KB

    duplicate post
    LabVIEW Champion . Do more with less code and in less time .

Maybe you are looking for

  • Add Contact's Email and Phone to the Lead result list on WEB UI

    Hello All, My requirement is to add Contact's Phone number and Email on Lead result list. Technical details: BT108S_LEA(Comp) BT108S_LEA/Result (View) RESULT (CN) I have enhanced context node ' Result ' and added new field through wizard (Ex: Contact

  • Purchase order determination

    Dear Gurus, Kindly let me know the process of how the system automatically determines the purchase order during Transfer in shipment cost seetlement transaction. If we have multiple POs, then how system identify which PO to pick. During maintaining o

  • List of services which can be monitor through scom

    Hello Experts.., We have to list-out Services which cab be monitored through SCOM  for windows server system. if there is any link and document on it ,Please provide us. if it's depend on MPs ,please provide services with MP List. Regards Richa KM

  • Yosemite update and Parallels and Windows not available

    I installed Yosemite.  I had Parallels 6 and Windows 7 partitioned.  Parallels 6 is not compatible.  I want to use Bootcamp to access my Microsoft documents.  How do I add Bootcamp, remove Parallels and keep Windows 7?

  • Icons in photoshop and illustrator are too small to work

    I have a samsung ativ book with high screen resolution (3200x1800). when I want to work with ps or ai their icons become extremly small. (the icons in indesign have a good size!) is there a possiblity to scale the icons up? I already turned up the sc