High CPU usage in cisco 7613 with rsp720-3cxl
Hi everybody,
our cisco 7613 has about 4.5 Gbps Tx/Rx IP traffic in total, and we run ospf with other cisco cloud for routing I list in the following some our router show.what is your idea about our high cpu usage .Is it in normal range with the listed cards and modules.How can I tune the rsp720 and other SIP-200,400,600 for better performances
why our interrupt rate is high ,and one thing more the total sum of 5sec in separate rows not equal to cpu utilization for five second 50%
show proc cpu sor
CPU utilization for five seconds: 50%/46%; one minute: 54%; five minutes: 59%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
8 196795220 12640741 15568 1.51% 0.38% 0.26% 0 Check heaps
224 1048610528 4169501364 0 1.19% 1.45% 1.44% 0 IP Input
13 374006320 3155162661 0 0.23% 0.26% 0.24% 0 ARP Input
217 119862004 985030884 121 0.15% 0.32% 0.25% 0 ADJ resolve pro
c
185 537716 1825736183 0 0.07% 0.03% 0.02% 0 ACE Tunnel Task
260 1550992 2983272818 0 0.07% 0.13% 0.15% 0 Ethernet Msec T
i
305 38186336 58050485 657 0.07% 0.02% 0.00% 0 XDR mcast
34 67208 11707798 5 0.07% 0.00% 0.00% 0 IPC Loadometer
27 232776 57160812 4 0.07% 0.01% 0.00% 0 IPC Periodic Ti
m
325 17539200 92894502 188 0.07% 0.15% 0.15% 0 CEF: IPv4 proce
s
195 7406636 43782487 169 0.07% 0.00% 0.00% 0 esw_vlan_stat_p
r
show ip route summ
IP routing table name is default (0x0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Replicates Overhead Memory (bytes)
static 1 120 0 7620 20812
connected 0 313 0 18860 53836
ospf 98 17 4892 0 589020 863984
Intra-area: 89 Inter-area: 383 External-1: 0 External-2: 0
NSSA External-1: 0 NSSA External-2: 4437
bgp 12880 0 1 0 60 172
External: 1 Internal: 0 Local: 0
ospf 410 0 269 0 16220 47344
Intra-area: 1 Inter-area: 0 External-1: 0 External-2: 268
NSSA External-1: 0 NSSA External-2: 0
internal 137 260544
Total 155 5595 0 631780 1246692
sh module
Mod Ports Card Type Model Serial No.
1 0 4-subslot SPA Interface Processor-200 7600-SIP-200
2 0 4-subslot SPA Interface Processor-400 7600-SIP-400
3 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
6 1 1-subslot SPA Interface Processor-600 7600-SIP-600
7 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE
8 2 Route Switch Processor 720 (Cold) RSP720-3CXL-GE
show ver
System image file is "bootdisk:c7600rsp72043-adventerprisek9-mz.122-33.SRE2.bin"
1 SIP-200 controller .
1 SIP-400 controller (1 Channelized OC3/STM-1).
1 SIP-600 controller (1 TenGigabitEthernet).
2 Virtual Ethernet interfaces
28 Gigabit Ethernet interfaces
1 Ten Gigabit Ethernet interface
1 Channelized STM-1 port
1 Channelized STM-1 port
show int vlan 1
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 2d23h
Input queue: 0/75/2886/1830 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2380531000 bits/sec, 287383 packets/sec
5 minute output rate 422133000 bits/sec, 254113 packets/sec
L2 Switched: ucast: 1200869468 pkt, 101172643240 bytes - mcast: 253599 pkt, 78
873415 bytes
L3 in Switched: ucast: 60947040633 pkt, 68919665115039 bytes - mcast: 0 pkt, 0
bytes mcast
L3 out Switched: ucast: 52594517004 pkt, 9869168832783 bytes mcast: 0 pkt, 0 b
ytes
62147839148 packets input, 69016175499764 bytes, 0 no buffer
Received 257634 broadcasts (0 IP multicasts)
0 runts, 0 giants, 15 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
53647248858 packets output, 10292998021217 bytes, 0 underruns
0 output errors, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Thank you for your hints and replying
These are our show ibc in 1 min interval
Interface information:
Interface IBC0/0
5 minute rx rate 20045000 bits/sec, 30183 packets/sec
5 minute tx rate 47394000 bits/sec, 60212 packets/sec
19879272237 packets input, 4006174536193 bytes
19835355282 broadcasts received
19808585787 packets output, 3981305571968 bytes
90548 broadcasts sent
0 Bridge Packet loopback drops
19756362091 Packets CEF Switched, 1320184 Packets Fast Switched
0 Packets SLB Switched, 0 Packets CWAN Switched
Label switched pkts dropped: 0 Pkts dropped during dma: 339549
Invalid pkts dropped: 0 Pkts dropped(not cwan consumed): 0
IPSEC pkts dropped: 635184
Xconnect pkts processed: 0, dropped: 0
Xconnect pkt reflection drops: 0
Total paks copied for process level 0
Total short paks sent in route cache 2605317676
Total throttle drops 265338 Input queue drops 5831090
total spd packets classified (120217214 low, 174503 medium, 3073 high)
total spd packets dropped (339549 low, 0 medium, 0 high)
spd prio pkts allowed in due to selective throttling (0 med, 0 high)
IBC resets = 1; last at 23:52:49.004 Sat Jan 19 2013
Driver Level Counters: (Cumulative, Zeroed only at Reset)
Frames Bytes
Rx(0) 26537712 3421085217
Rx(1) 3449063135 2838813650
Tx(0) 3390340306 2016620276
Input Drop Frame Count
Rx0 = 0 Rx1 = 2488435
Per Queue Receive Errors:
FRME OFLW BUFE NOENP DISCRD DISABLE BADCOUNT
Rx0 0 0 0 0 0 0 0
Rx1 0 0 0 3633 0 0 0
Tx Errors/State:
One Collision Error = 0 More Collisions = 0
No Encap Error = 0 Deferred Error = 0
Loss Carrier Error = 0 Late Collision Error = 0
Excessive Collisions = 0 Buffer Error = 0
Tx Freeze Count = 0 Tx Intrpt Serv timeout= 1
Tx Flow State = FLOW_ON
Tx Flow Off Count = 0 Tx Flow On Count = 0
Counters collected at Idb:
Is input throttled = 0 Throttle Count = 0
Rx Resource Errors = 0 Input Drops = 2488435
Input Errors = 194243
Output Drops = 0 Giants/Runts = 0/0
Dma Mem Error = 0 Input Overrun = 0
Hash match table for multicast (in use 0, maximum 64 entries):
show ibc
Interface information:
Interface IBC0/0
5 minute rx rate 20194000 bits/sec, 30412 packets/sec
5 minute tx rate 47753000 bits/sec, 60663 packets/sec
19891125514 packets input, 4007158118761 bytes
19847185365 broadcasts received
19820407164 packets output, 3982279276274 bytes
90576 broadcasts sent
0 Bridge Packet loopback drops
19768178233 Packets CEF Switched, 1321008 Packets Fast Switched
0 Packets SLB Switched, 0 Packets CWAN Switched
Label switched pkts dropped: 0 Pkts dropped during dma: 339549
Invalid pkts dropped: 0 Pkts dropped(not cwan consumed): 0
IPSEC pkts dropped: 635574
Xconnect pkts processed: 0, dropped: 0
Xconnect pkt reflection drops: 0
Total paks copied for process level 0
Total short paks sent in route cache 2606549061
Total throttle drops 265338 Input queue drops 5831090
total spd packets classified (120252754 low, 174531 medium, 3074 high)
total spd packets dropped (339549 low, 0 medium, 0 high)
spd prio pkts allowed in due to selective throttling (0 med, 0 high)
IBC resets = 1; last at 23:52:49.004 Sat Jan 19 2013
Driver Level Counters: (Cumulative, Zeroed only at Reset)
Frames Bytes
Rx(0) 26550723 3422835145
Rx(1) 3461063605 176652699
Tx(0) 3402319442 3368513724
Input Drop Frame Count
Rx0 = 0 Rx1 = 2490155
Per Queue Receive Errors:
FRME OFLW BUFE NOENP DISCRD DISABLE BADCOUNT
Rx0 0 0 0 0 0 0 0
Rx1 0 0 0 3633 0 0 0
Tx Errors/State:
One Collision Error = 0 More Collisions = 0
No Encap Error = 0 Deferred Error = 0
Loss Carrier Error = 0 Late Collision Error = 0
Excessive Collisions = 0 Buffer Error = 0
Tx Freeze Count = 0 Tx Intrpt Serv timeout= 1
Tx Flow State = FLOW_ON
Tx Flow Off Count = 0 Tx Flow On Count = 0
Counters collected at Idb:
Is input throttled = 0 Throttle Count = 0
Rx Resource Errors = 0 Input Drops = 2490155
Input Errors = 194358
Output Drops = 0 Giants/Runts = 0/0
Dma Mem Error = 0 Input Overrun = 0
Hash match table for multicast (in use 0, maximum 64 entries):
and sorry what is your idea about total sum of 5sec in separate rows not equal to cpu utilization for five second 50%
Similar Messages
-
Hi all,
I'm having high CPU usage with one of my Cisco 3845.
It works as an IP-IP Gateway and the CPU is quite high when the total number of calls only around 100-200 calls.
I check the CPU usage with "show process cpu sort" and it looks like there are some "hidden" processes that consuming CPU.
For example, 41% is total CPU, 25% is due to interrups, so CPU utilization on process level = 41 - 25 = 16%.
But as showed below, processes don't consume that much CPU, only around 7% ???
Please help to advise on this case. Any help is highly appreciated..
Thank you.
3845-GW#show process cpu sort | ex 0.00% 0.00% 0.00%
CPU utilization for five seconds: 41%/25%; one minute: 46%; five minutes: 47%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
382 6619708 1473171 4493 1.59% 1.81% 1.92% 0 CCSIP_SPI_CONTRO
141 4228940 10181955 415 1.35% 1.51% 1.57% 0 IP Input
65 2450824 163102 15026 1.19% 1.16% 1.17% 0 Per-Second Jobs
370 2702292 3709512 728 0.87% 0.88% 0.88% 0 VOIP_RTCP
224 321680 245640 1309 0.47% 0.49% 0.50% 0 AFW_application_
112 93940 18093506 5 0.39% 0.31% 0.32% 0 Ethernet Msec Ti
384 1058280 1553567 681 0.23% 0.28% 0.30% 0 CCSIP_UDP_SOCKET
2 18148 32905 551 0.07% 0.03% 0.02% 0 Load Meter
137 35644 4657843 7 0.07% 0.04% 0.05% 0 IPAM Manager
189 206392 267959 770 0.07% 0.05% 0.07% 0 TCP Protocols
30 30792 198554 155 0.07% 0.01% 0.00% 0 ARP Input
368 145456 176151 825 0.07% 0.04% 0.05% 0 CC-API_VCM
28 9628 32759 293 0.00% 0.01% 0.00% 0 Environmental mo
48 221352 37922 5837 0.00% 0.11% 0.11% 0 Net Background
63 16728 32924 508 0.00% 0.01% 0.00% 0 Compute load avg
64 72080 2781 25918 0.00% 0.01% 0.00% 0 Per-minute Jobs
6 371644 29792 12474 0.00% 0.14% 0.12% 0 Check heaps
176 12216 240288 50 0.00% 0.01% 0.00% 0 CEF: IPv4 proces
284 36416 4929826 7 0.00% 0.02% 0.01% 0 MMON MENG
307 12168 806151 15 0.00% 0.01% 0.00% 0 Atheros LED Ctro
335 35300 19755 1786 0.00% 3.16% 1.00% 708 Virtual Exec
3845-GW#sh int g0/0
GigabitEthernet0/0 is up, line protocol is up
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/2/56803 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1551000 bits/sec, 5751 packets/sec
5 minute output rate 4207000 bits/sec, 7643 packets/sec
925128804 packets input, 939078510 bytes, 0 no buffer
Received 62732 broadcasts (0 IP multicasts)
0 runts, 0 giants, 2 throttles
2 input errors, 0 CRC, 0 frame, 2 overrun, 0 ignored
0 watchdog, 3763438515 multicast, 0 pause input
1472816545 packets output, 3214770103 bytes, 0 underruns
0 output errors, 2067720191 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 2281155551 late collision, 0 deferred
2 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
3845-GW#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/30335 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1684000 bits/sec, 7697 packets/sec
5 minute output rate 3372000 bits/sec, 5632 packets/sec
1484558664 packets input, 2383177786 bytes, 0 no buffer
Received 208998 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
2 input errors, 0 CRC, 0 frame, 2 overrun, 0 ignored
0 watchdog, 3060386282 multicast, 0 pause input
903478941 packets output, 2814588854 bytes, 0 underruns
0 output errors, 2910776303 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 4157448025 late collision, 0 deferred
2 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped outHas this been something that just recently started happening, or have you had this issue for a while? Have you installed any new programs recently?
You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well). There is a module for startup manager. You can go in and disable stuff that starts with the computer. I would advise unchecking adobe, java, quicktime, printers, etc. Anything that doesn't REALLY need to start with the computer. The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick. I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background.
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system) -
Hi All,
I have a cisco 2811 that is high in CPU usage. Below is my IOS version and process usage details.
Cisco IOS Software, 2800 Software (C2800NM-IPBASEK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 03-Sep-10 05:39 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
ipscape-myob uptime is 6 weeks, 5 days, 17 hours, 18 minutes
System returned to ROM by reload at 10:33:59 UTC Thu Apr 10 2014
System image file is "flash:c2800nm-ipbasek9-mz.124-24.T4.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2811 (revision 53.51) with 514048K/10240K bytes of memory.
Processor board ID FHK1238F1D4
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CPU utilization for five seconds: 90%/77%; one minute: 79%; five minutes: 76%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
8 20693808 28614857 723 7.67% 1.24% 0.44% 0 IP SLAs Respond e
91 13460456 18459988 729 3.27% 0.67% 0.31% 0 IP Input
143 3167640 1026953957 3 1.19% 1.62% 1.68% 0 HQF Shaper Back g
184 809676 128826693 6 0.39% 0.38% 0.39% 0 PPP manager
196 1072 112 9571 0.31% 0.23% 0.06% 514 Virtual Exec
185 771340 128826711 5 0.23% 0.18% 0.16% 0 PPP Events
Could you please provide me some info on this issues.
Thank You!Has this been something that just recently started happening, or have you had this issue for a while? Have you installed any new programs recently?
You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well). There is a module for startup manager. You can go in and disable stuff that starts with the computer. I would advise unchecking adobe, java, quicktime, printers, etc. Anything that doesn't REALLY need to start with the computer. The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick. I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background.
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system) -
High CPU Utilization in 7603 router with RSP720-10GE
Hi everyone
We have a 7603 router with "RSP720-10GE" and we have high cpu utilization due to high amount of interrupts.
The output of “show cef drop” and “show ip cef switching statistics” commands show lots of packets that have been dropped by CEF.
But CEF is enabled on every physical interfaces and on every GRE tunnel that we have on this router.
As I understand the output of “show ip cef switching statistics” command shows some of the reasons for CEF dropping packets like “Routed to Null0” but I don’t know how to solve them. For example I can’t delete routes to Null0 because it’s going to cause routing loops in our network. Could you please help meHey,
The output shows high interrupt to CPU, So collect the last output multiple times to see if the DROP values are incrementing. Also configure NetDr captures to see what packets are punted to CPU. I am adding a link for same:
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/116475-technote-product-00.html
HTH.
Regards,
RS -
Hi there,
since a few days there is on some machines (40-60) a high cpu usage on one core (quad core cpu machines) with the WMIPRSVE.EXE if the HARDWARE INVENTORY CYCLE started.
i try out some tests, read some forum articles and troubleshooting the WMI management but a real problem i doesn´t see.
in some articles i read that hardware inventory runs about minutes up to more hours but some machines runs longer, someone more as 1 day.
here an example of mine PC:
at 8:07 i started Hardware Inventory Cycle, in the InventoryAgent.log i can see that some Collection Namespace are captured.
after a few minutes there stopped and does nothing round about 5.9 hours or better, after 21436.097 Seconds.
For any hints i am grateful. :)
Inventory: *********************** Start of message processing. ***********************
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Inventory: Message type is InventoryAction InventoryAgent
18.03.2015 08:09:56 11088 (0x2B50)
Inventory: Temp directory = C:\WINDOWS\CCM\Inventory\Temp\
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Inventory: Clearing old collected files. InventoryAgent
18.03.2015 08:09:56 11088 (0x2B50)
Inventory: Opening store for action {00000000-0000-0000-0000-000000000001} ...
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
CInvState::VerifyInventoryVersionNumber: Mismatch found for '{00000000-0000-0000-0000-000000000001}': 4.2 vs. 0.0
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Inventory: Version number mismatch; will do a Full report.
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Inventory: Action=Hardware, ReportType=ReSync, MajorVersion=5, MinorVersion=0
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Inventory: Initialization completed in 0.141 seconds
InventoryAgent 18.03.2015 08:09:56
11088 (0x2B50)
Collection: Namespace = \\localhost\root\Microsoft\appvirt\client; Query = SELECT __CLASS, __PATH, __RELPATH, CachedLaunchSize, CachedPercentage, CachedSize, LaunchSize, Name, PackageGUID, TotalSize, Version, VersionGUID FROM Package; Timeout = 600 secs.
InventoryAgent 18.03.2015 08:09:56
7836 (0x1E9C)
Failed to get IWbemService Ptr for \\localhost\root\vm\VirtualServer Namespace: 8004100E
InventoryAgent 18.03.2015 08:10:02
7836 (0x1E9C)
Failed to enumerate instances of VirtualMachine: 8004100E
InventoryAgent 18.03.2015 08:10:02
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2\sms; Query = SELECT __CLASS, __PATH, __RELPATH, AddressWidth, BrandID, CPUHash, CPUKey, DataWidth, DeviceID, Family, Is64Bit, IsHyperthreadCapable, IsMobile, IsTrustedExecutionCapable, IsVitualizationCapable, Manufacturer,
MaxClockSpeed, Name, NormSpeed, NumberOfCores, NumberOfLogicalProcessors, PCache, ProcessorId, ProcessorType, Revision, SocketDesignation, Status, SystemName, Version FROM SMS_Processor; Timeout = 600 secs.
InventoryAgent 18.03.2015 08:10:02
7836 (0x1E9C)
Collection: Namespace = \\.\root\CCM\powermanagementagent; Query = SELECT __CLASS, __PATH, __RELPATH, Requester, RequesterInfo, RequesterType, RequestType, Time, UnknownRequester FROM CCM_PwrMgmtLastSuspendError; Timeout = 600 secs.
InventoryAgent 18.03.2015 08:10:03
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, Availability, Description, DeviceID, Manufacturer, Name, Status FROM Win32_IDEController; Timeout = 600 secs.
InventoryAgent 18.03.2015 08:10:03
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2\sms; Query = SELECT __CLASS, __PATH, __RELPATH, BinFileVersion, BinProductVersion, Description, ExecutableName, FilePropertiesHash, FilePropertiesHashEx, FileSize, FileVersion, HasPatchAdded, InstalledFilePath, IsSystemFile,
IsVitalFile, Language, Product, ProductCode, ProductVersion, Publisher FROM SMS_InstalledExecutable; Timeout = 600 secs.
InventoryAgent 18.03.2015 08:10:03
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, DefaultIPGateway, DHCPEnabled, DHCPServer, DNSDomain, DNSHostName, Index, IPAddress, IPEnabled, IPSubnet, MACAddress, ServiceName FROM Win32_NetworkAdapterConfiguration; Timeout
= 600 secs. InventoryAgent
18.03.2015 14:06:43 7836 (0x1E9C)
Collection: Namespace = \\.\root\Nap; Query = SELECT __CLASS, __PATH, __RELPATH, description, fixupState, friendlyName, id, infoClsid, isBound, percentage, registrationDate, vendorName, version FROM NAP_SystemHealthAgent; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:06:43
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2\sms; Query = SELECT __CLASS, __PATH, __RELPATH, AdditionalProductCodes, CompanyName, ExplorerFileName, FileDescription, FilePropertiesHash, FileSize, FileVersion, FolderPath, LastUsedTime, LastUserName, msiDisplayName,
msiPublisher, msiVersion, OriginalFileName, ProductCode, ProductLanguage, ProductName, ProductVersion, SoftwarePropertiesHash FROM CCM_RecentlyUsedApps; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:06:43
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, BankLabel, Capacity, Caption, CreationClassName, DataWidth, Description, DeviceLocator, FormFactor, HotSwappable, InstallDate, InterleaveDataDepth, InterleavePosition, Manufacturer,
MemoryType, Model, Name, OtherIdentifyingInfo, PartNumber, PositionInRow, PoweredOn, Removable, Replaceable, SerialNumber, SKU, Speed, Status, Tag, TotalWidth, TypeDetail, Version FROM Win32_PhysicalMemory; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:07:02
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, Availability, Description, DeviceID, InstallDate, Manufacturer, Name, PNPDeviceID, ProductName, Status FROM Win32_SoundDevice; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:07:02
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, Caption, ClassGuid, ConfigManagerErrorCode, ConfigManagerUserConfig, CreationClassName, Description, DeviceID, Manufacturer, Name, PNPDeviceID, Service, Status, SystemCreationClassName,
SystemName FROM Win32_USBDevice; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Collection: 62/74 inventory data items successfully inventoried.
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: Collection Task completed in 21436.097 seconds
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: 12 Collection Task(s) failed. InventoryAgent
18.03.2015 14:07:12 7836 (0x1E9C)
Inventory: Temp report = C:\WINDOWS\CCM\Inventory\Temp\25bf01b2-12fc-4eea-8e97-a51b3c75ba50.xml
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: Starting reporting task. InventoryAgent
18.03.2015 14:07:12 7552 (0x1D80)
Reporting: 4381 report entries created. InventoryAgent
18.03.2015 14:07:13 7552 (0x1D80)
Inventory: Reporting Task completed in 1.030 seconds
InventoryAgent 18.03.2015 14:07:13
7552 (0x1D80)
Inventory: Successfully sent report. Destination:mp:MP_HinvEndpoint, ID: {5541A94A-BED9-4132-AE54-110CB6896F02}, Timeout: 80640 minutes MsgMode: Signed, Not Encrypted
InventoryAgent 18.03.2015 14:07:13
7552 (0x1D80)
Inventory: Cycle completed in 21453.570 seconds
InventoryAgent 18.03.2015 14:07:30
7552 (0x1D80)
Inventory: Action completed. InventoryAgent
18.03.2015 14:07:30 7552 (0x1D80)
Inventory: ************************ End of message processing. ************************
InventoryAgent 18.03.2015 14:07:30
7552 (0x1D80)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, Caption, ClassGuid, ConfigManagerErrorCode, ConfigManagerUserConfig, CreationClassName, Description, DeviceID, Manufacturer, Name, PNPDeviceID, Service, Status, SystemCreationClassName,
SystemName FROM Win32_USBDevice; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Collection: 62/74 inventory data items successfully inventoried.
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: Collection Task completed in 21436.097 seconds
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: 12 Collection Task(s) failed. InventoryAgent
18.03.2015 14:07:12 7836 (0x1E9C)
Inventory: Temp report = C:\WINDOWS\CCM\Inventory\Temp\25bf01b2-12fc-4eea-8e97-a51b3c75ba50.xml
InventoryAgent 18.03.2015 14:07:12
7836 (0x1E9C)
Inventory: Starting reporting task. InventoryAgent
18.03.2015 14:07:12 7552 (0x1D80)
Reporting: 4381 report entries created. InventoryAgent
18.03.2015 14:07:13 7552 (0x1D80)
Inventory: Reporting Task completed in 1.030 seconds
InventoryAgent 18.03.2015 14:07:13
7552 (0x1D80)
Inventory: Successfully sent report. Destination:mp:MP_HinvEndpoint, ID: {5541A94A-BED9-4132-AE54-110CB6896F02}, Timeout: 80640 minutes MsgMode: Signed, Not Encrypted
InventoryAgent 18.03.2015 14:07:13
7552 (0x1D80)
Inventory: Cycle completed in 21453.570 seconds
InventoryAgent 18.03.2015 14:07:30
7552 (0x1D80)
Inventory: Action completed. InventoryAgent
18.03.2015 14:07:30 7552 (0x1D80)
Inventory: ************************ End of message processing. ************************
InventoryAgent 18.03.2015 14:07:30
7552 (0x1D80)InventoryAgent 18.03.2015 08:10:03
7836 (0x1E9C)
Collection: Namespace = \\.\root\cimv2; Query = SELECT __CLASS, __PATH, __RELPATH, DefaultIPGateway, DHCPEnabled, DHCPServer, DNSDomain, DNSHostName, Index, IPAddress, IPEnabled, IPSubnet, MACAddress, ServiceName FROM Win32_NetworkAdapterConfiguration; Timeout
= 600 secs. InventoryAgent
18.03.2015 14:06:43 7836 (0x1E9C)
Collection: Namespace = \\.\root\Nap; Query = SELECT __CLASS, __PATH, __RELPATH, description, fixupState, friendlyName, id, infoClsid, isBound, percentage, registrationDate, vendorName, version FROM NAP_SystemHealthAgent; Timeout = 600 secs.
InventoryAgent 18.03.2015 14:06:43
7836 (0x1E9C)
Looks like something in one or both of those wmi queries. it goes from 8:10:03 to 14:06:43 right around there. 6 hours to do that...
try running those queries from wbemtest manually; and see which one just never finishes.
Standardize. Simplify. Automate. -
Since 10.4.6 Update: "ATSServer" with high CPU-usage when opening PDFs
Since I've updated to 10.4.6 my system is very slow when I open PDFs (in "Preview" or "Acrobat").
This is caused by the process "ATSServer" which goes through every file in "~/Library/Fonts" (I have over 4.800 files there - but just a view are activated by "FontBook") and so it takes very high CPU-usage.
I didn't have this problem bevore the update and I didn't make any changes on my font settings.
I've cleaned the font cache, but it doesn't help.
Any ideas?
Ciao
Mephizo
PS: Excuse my poor English.
PowerBook G4 17'' 1.67 GHz Mac OS X (10.4.6)
PowerBook G4 17'' 1.67 GHz Mac OS X (10.4.6)I haven't noticed any change myself, Dan, but I have the 2 GHz model.
One thing I HAVE noticed though after OS updates is that they can often result in a fair amount of file and free space fragmentation immediately after installation. OSX's routines will deal with fragmentation of small files , but not of large ones (over 20 Meg), and it won't deal very effectively with free space fragmentation. If your HD is getting full this can cause significant slowdowns, especially where video is involved.
You should also run DiskUtility and check for any directory and permissions issues.
Cheers
Rod -
High CPU usage with Coherence 3.5.0 cluster node
We're noticing sustained high CPU usage on one of our Coherence nodes - this happens after running a job that pretty intensively interacts with the cache. The jobs complete, however we still see the Coherence process using approximately the equivalent of one core's worth of CPU. I took a couple of thread dumps about fifteen minutes apart, and the only noticeable differences are within the PacketListener1 and PacketListenerN threads - they're holding locks on different DatagramPacket instances, which suggests to be that this may be the piece of code that is looping.
There are two other cache nodes in this particular cluster - both of them on a different machine - and neither of them are exhibiting the same CPU utilization.
Environment:
Coherence 3.5.0
Java - BEA JRockit(R) (build R27.6.3-40_o-112056-1.6.0_11-20090318-2103-linux-x86_64, compiled mode)
Has anyone encountered this scenario before?
Here's a copy of the two thread dumps:
Thread Dump 1 -
===== FULL THREAD DUMP ===============
Thu Feb 24 21:45:00 2011
BEA JRockit(R) R27.6.3-40_o-112056-1.6.0_11-20090318-2103-linux-x86_64
"Main Thread" id=1 idx=0x4 tid=18143 prio=5 alive, in native, waiting
-- Waiting for notification on: java/lang/Class@0x43587b58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/net/DefaultCacheServer.main(DefaultCacheServer.java:80)
^-- Lock released while waiting: java/lang/Class@0x43587b58[fat lock]
at com/zzzz/carbon/cacheserver/ZzzzCoherenceServerStartup.doWork(ZzzzCoherenceServerStartup.java:29)
at com/zzzz/util/runner/ZzzzRunnerBase.run(ZzzzRunnerBase.java:23)
at com/zzzz/carbon/cacheserver/ZzzzCoherenceServerStartup.main(ZzzzCoherenceServerStartup.java:16)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Signal Handler)" id=2 idx=0x8 tid=18144 prio=5 alive, in native, daemon
"(GC Main Thread)" id=3 idx=0xc tid=18145 prio=5 alive, in native, daemon
"(GC Worker Thread 1)" id=? idx=0x10 tid=18146 prio=5 alive, in native, daemon
"(GC Worker Thread 2)" id=? idx=0x14 tid=18147 prio=5 alive, in native, daemon
"(GC Worker Thread 3)" id=? idx=0x18 tid=18148 prio=5 alive, in native, daemon
"(GC Worker Thread 4)" id=? idx=0x1c tid=18149 prio=5 alive, in native, daemon
"(Code Generation Thread 1)" id=4 idx=0x20 tid=18150 prio=5 alive, in native, native_waiting, daemon
"(Code Optimization Thread 1)" id=5 idx=0x24 tid=18151 prio=5 alive, in native, native_waiting, daemon
"(VM Periodic Task)" id=6 idx=0x28 tid=18152 prio=10 alive, in native, daemon
"Finalizer" id=7 idx=0x2c tid=18153 prio=8 alive, in native, native_waiting, daemon
at jrockit/memory/Finalizer.waitForFinalizees([Ljava/lang/Object;)I(Native Method)
at jrockit/memory/Finalizer.access$500(Finalizer.java:12)
at jrockit/memory/Finalizer$4.run(Finalizer.java:159)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Reference Handler" id=8 idx=0x30 tid=18154 prio=10 alive, in native, native_waiting, daemon
at java/lang/ref/Reference.waitForActivatedQueue()Ljava/lang/ref/Reference;(Native Method)
at java/lang/ref/Reference.access$100(Reference.java:11)
at java/lang/ref/Reference$ReferenceHandler.run(Reference.java:79)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Sensor Event Thread)" id=9 idx=0x34 tid=18155 prio=5 alive, in native, daemon
"Logger@9217551 3.5/459" id=12 idx=0x38 tid=18158 prio=3 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/application/console/Coherence$Logger$Queue@0x4e1faef8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/application/console/Coherence$Logger$Queue@0x4e1faef8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketListener1" id=14 idx=0x3c tid=18159 prio=8 alive, in native, daemon
at java/net/PlainDatagramSocketImpl.receive0(Ljava/net/DatagramPacket;)V(Native Method)
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb21360[recursive]
at java/net/PlainDatagramSocketImpl.receive(PlainDatagramSocketImpl.java:136)[inlined]
at java/net/DatagramSocket.receive(DatagramSocket.java:712)[optimized]
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb21360[thin lock]
^-- Holding lock: java/net/DatagramPacket@0x73aa4e80[thin lock]
^-- Holding lock: java/net/DatagramSocket@0x4cb21338[thin lock]
at com/tangosol/coherence/component/net/socket/UdpSocket.receive(UdpSocket.CDB:20)[optimized]
at com/tangosol/coherence/component/net/UdpPacket.receive(UdpPacket.CDB:4)[optimized]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketListener.onNotify(PacketListener.CDB:19)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketReceiver" id=15 idx=0x40 tid=18160 prio=7 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketReceiver$InQueue@0x4cf60d58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketReceiver.onWait(PacketReceiver.CDB:2)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketReceiver$InQueue@0x4cf60d58[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketPublisher" id=16 idx=0x44 tid=18161 prio=6 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketPublisher.onWait(PacketPublisher.CDB:2)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketSpeaker" id=17 idx=0x48 tid=18162 prio=8 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketSpeaker$BundlingQueue@0x4cabe9d8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/queue/ConcurrentQueue.waitForEntry(ConcurrentQueue.CDB:16)
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketSpeaker$BundlingQueue@0x4cabe9d8[fat lock]
at com/tangosol/coherence/component/util/queue/ConcurrentQueue.remove(ConcurrentQueue.CDB:7)
at com/tangosol/coherence/component/util/Queue.remove(Queue.CDB:1)
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketSpeaker.onNotify(PacketSpeaker.CDB:62)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketListenerN" id=18 idx=0x4c tid=18163 prio=8 alive, in native, daemon
at java/net/PlainDatagramSocketImpl.receive0(Ljava/net/DatagramPacket;)V(Native Method)
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb221b0[recursive]
at java/net/PlainDatagramSocketImpl.receive(PlainDatagramSocketImpl.java:136)[inlined]
at java/net/DatagramSocket.receive(DatagramSocket.java:712)[optimized]
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb221b0[thin lock]
^-- Holding lock: java/net/DatagramPacket@0x73e59890[thin lock]
^-- Holding lock: java/net/MulticastSocket@0x4cb22178[thin lock]
at com/tangosol/coherence/component/net/socket/UdpSocket.receive(UdpSocket.CDB:20)[optimized]
at com/tangosol/coherence/component/net/UdpPacket.receive(UdpPacket.CDB:4)[optimized]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketListener.onNotify(PacketListener.CDB:19)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Cluster|Member(Id=2, Timestamp=2011-02-23 16:25:36.488, Address=10.10.100.77:8095, MachineId=25677, Location=site:emtzzzz.com,machine:njdev04,process:18142,member:cldev201~carboncachelauncher~181)" id=19 idx=0x50 tid=18164 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4cac64d8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4cac64d8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"TcpRingListener" id=20 idx=0x54 tid=18165 prio=6 alive, in native, daemon
at java/net/PlainSocketImpl.socketAccept(Ljava/net/SocketImpl;)V(Native Method)
at java/net/PlainSocketImpl.accept(PlainSocketImpl.java:384)
^-- Holding lock: java/net/SocksSocketImpl@0x4cb227d8[thin lock]
at java/net/ServerSocket.implAccept(ServerSocket.java:453)
at java/net/ServerSocket.accept(ServerSocket.java:421)
at com/tangosol/coherence/component/net/socket/TcpSocketAccepter.accept(TcpSocketAccepter.CDB:18)
at com/tangosol/coherence/component/util/daemon/TcpRingListener.acceptConnection(TcpRingListener.CDB:10)
at com/tangosol/coherence/component/util/daemon/TcpRingListener.onNotify(TcpRingListener.CDB:9)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Invocation:Management:EventDispatcher" id=22 idx=0x58 tid=18166 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher$Queue@0x4ab76140[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher$Queue@0x4ab76140[fat lock]
at com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher.onWait(Service.CDB:7)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Invocation:Management" id=23 idx=0x5c tid=18167 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4ab75508[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4ab75508[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"DistributedCache" id=25 idx=0x60 tid=18168 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4a3869b0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4a3869b0[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
===== END OF THREAD DUMP ===============
Thread Dump 2 -
===== FULL THREAD DUMP ===============
Thu Feb 24 21:27:53 2011
BEA JRockit(R) R27.6.3-40_o-112056-1.6.0_11-20090318-2103-linux-x86_64
"Main Thread" id=1 idx=0x4 tid=18143 prio=5 alive, in native, waiting
-- Waiting for notification on: java/lang/Class@0x43587b58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/net/DefaultCacheServer.main(DefaultCacheServer.java:80)
^-- Lock released while waiting: java/lang/Class@0x43587b58[fat lock]
at com/zzzz/carbon/cacheserver/ZzzzCoherenceServerStartup.doWork(ZzzzCoherenceServerStartup.java:29)
at com/zzzz/util/runner/ZzzzRunnerBase.run(ZzzzRunnerBase.java:23)
at com/zzzz/carbon/cacheserver/ZzzzCoherenceServerStartup.main(ZzzzCoherenceServerStartup.java:16)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Signal Handler)" id=2 idx=0x8 tid=18144 prio=5 alive, in native, daemon
"(GC Main Thread)" id=3 idx=0xc tid=18145 prio=5 alive, in native, native_waiting, daemon
"(GC Worker Thread 1)" id=? idx=0x10 tid=18146 prio=5 alive, in native, daemon
"(GC Worker Thread 2)" id=? idx=0x14 tid=18147 prio=5 alive, in native, daemon
"(GC Worker Thread 3)" id=? idx=0x18 tid=18148 prio=5 alive, in native, daemon
"(GC Worker Thread 4)" id=? idx=0x1c tid=18149 prio=5 alive, in native, daemon
"(Code Generation Thread 1)" id=4 idx=0x20 tid=18150 prio=5 alive, in native, native_waiting, daemon
"(Code Optimization Thread 1)" id=5 idx=0x24 tid=18151 prio=5 alive, in native, native_waiting, daemon
"(VM Periodic Task)" id=6 idx=0x28 tid=18152 prio=10 alive, in native, daemon
"Finalizer" id=7 idx=0x2c tid=18153 prio=8 alive, in native, native_waiting, daemon
at jrockit/memory/Finalizer.waitForFinalizees([Ljava/lang/Object;)I(Native Method)
at jrockit/memory/Finalizer.access$500(Finalizer.java:12)
at jrockit/memory/Finalizer$4.run(Finalizer.java:159)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Reference Handler" id=8 idx=0x30 tid=18154 prio=10 alive, in native, native_waiting, daemon
at java/lang/ref/Reference.waitForActivatedQueue()Ljava/lang/ref/Reference;(Native Method)
at java/lang/ref/Reference.access$100(Reference.java:11)
at java/lang/ref/Reference$ReferenceHandler.run(Reference.java:79)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Sensor Event Thread)" id=9 idx=0x34 tid=18155 prio=5 alive, in native, daemon
"Logger@9217551 3.5/459" id=12 idx=0x38 tid=18158 prio=3 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/application/console/Coherence$Logger$Queue@0x4e1faef8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/application/console/Coherence$Logger$Queue@0x4e1faef8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketListener1" id=14 idx=0x3c tid=18159 prio=8 alive, in native, daemon
at java/net/PlainDatagramSocketImpl.receive0(Ljava/net/DatagramPacket;)V(Native Method)
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb21360[recursive]
at java/net/PlainDatagramSocketImpl.receive(PlainDatagramSocketImpl.java:136)[inlined]
at java/net/DatagramSocket.receive(DatagramSocket.java:712)[optimized]
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb21360[thin lock]
^-- Holding lock: java/net/DatagramPacket@0x73a80930[thin lock]
^-- Holding lock: java/net/DatagramSocket@0x4cb21338[thin lock]
at com/tangosol/coherence/component/net/socket/UdpSocket.receive(UdpSocket.CDB:20)[optimized]
at com/tangosol/coherence/component/net/UdpPacket.receive(UdpPacket.CDB:4)[optimized]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketListener.onNotify(PacketListener.CDB:19)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketReceiver" id=15 idx=0x40 tid=18160 prio=7 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketReceiver$InQueue@0x4cf60d58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketReceiver.onWait(PacketReceiver.CDB:2)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketReceiver$InQueue@0x4cf60d58[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketPublisher" id=16 idx=0x44 tid=18161 prio=6 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketPublisher.onWait(PacketPublisher.CDB:2)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketPublisher$InQueue@0x4ca053a8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketSpeaker" id=17 idx=0x48 tid=18162 prio=8 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/net/Cluster$PacketSpeaker$BundlingQueue@0x4cabe9d8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/queue/ConcurrentQueue.waitForEntry(ConcurrentQueue.CDB:16)
^-- Lock released while waiting: com/tangosol/coherence/component/net/Cluster$PacketSpeaker$BundlingQueue@0x4cabe9d8[fat lock]
at com/tangosol/coherence/component/util/queue/ConcurrentQueue.remove(ConcurrentQueue.CDB:7)
at com/tangosol/coherence/component/util/Queue.remove(Queue.CDB:1)
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketSpeaker.onNotify(PacketSpeaker.CDB:62)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"PacketListenerN" id=18 idx=0x4c tid=18163 prio=8 alive, in native, daemon
at java/net/PlainDatagramSocketImpl.receive0(Ljava/net/DatagramPacket;)V(Native Method)
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb221b0[recursive]
at java/net/PlainDatagramSocketImpl.receive(PlainDatagramSocketImpl.java:136)[inlined]
at java/net/DatagramSocket.receive(DatagramSocket.java:712)[optimized]
^-- Holding lock: java/net/PlainDatagramSocketImpl@0x4cb221b0[thin lock]
^-- Holding lock: java/net/DatagramPacket@0x5e55a240[thin lock]
^-- Holding lock: java/net/MulticastSocket@0x4cb22178[thin lock]
at com/tangosol/coherence/component/net/socket/UdpSocket.receive(UdpSocket.CDB:20)[optimized]
at com/tangosol/coherence/component/net/UdpPacket.receive(UdpPacket.CDB:4)[optimized]
at com/tangosol/coherence/component/util/daemon/queueProcessor/packetProcessor/PacketListener.onNotify(PacketListener.CDB:19)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Cluster|Member(Id=2, Timestamp=2011-02-23 16:25:36.488, Address=10.10.100.77:8095, MachineId=25677, Location=site:emtzzzz.com,machine:njdev04,process:18142,member:cldev201~carboncachelauncher~181)" id=19 idx=0x50 tid=18164 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4cac64d8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4cac64d8[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"TcpRingListener" id=20 idx=0x54 tid=18165 prio=6 alive, in native, daemon
at java/net/PlainSocketImpl.socketAccept(Ljava/net/SocketImpl;)V(Native Method)
at java/net/PlainSocketImpl.accept(PlainSocketImpl.java:384)
^-- Holding lock: java/net/SocksSocketImpl@0x4cb227d8[thin lock]
at java/net/ServerSocket.implAccept(ServerSocket.java:453)
at java/net/ServerSocket.accept(ServerSocket.java:421)
at com/tangosol/coherence/component/net/socket/TcpSocketAccepter.accept(TcpSocketAccepter.CDB:18)
at com/tangosol/coherence/component/util/daemon/TcpRingListener.acceptConnection(TcpRingListener.CDB:10)
at com/tangosol/coherence/component/util/daemon/TcpRingListener.onNotify(TcpRingListener.CDB:9)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:37)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Invocation:Management:EventDispatcher" id=22 idx=0x58 tid=18166 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher$Queue@0x4ab76140[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher$Queue@0x4ab76140[fat lock]
at com/tangosol/coherence/component/util/daemon/queueProcessor/Service$EventDispatcher.onWait(Service.CDB:7)
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Invocation:Management" id=23 idx=0x5c tid=18167 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4ab75508[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4ab75508[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"DistributedCache" id=25 idx=0x60 tid=18168 prio=5 alive, in native, waiting, daemon
-- Waiting for notification on: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4a3869b0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)[optimized]
at com/tangosol/coherence/component/util/Daemon.onWait(Daemon.CDB:18)[inlined]
at com/tangosol/coherence/component/util/daemon/queueProcessor/service/Grid.onWait(Grid.CDB:9)[optimized]
^-- Lock released while waiting: com/tangosol/coherence/component/util/queue/concurrentQueue/DualQueue@0x4a3869b0[fat lock]
at com/tangosol/coherence/component/util/Daemon.run(Daemon.CDB:34)
at java/lang/Thread.run(Thread.java:619)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
===== END OF THREAD DUMP ===============Charlie, Cameron,
Thanks for following up. To answer Cameron's question - yes, running top shows that it is this process using a significant amount of the CPU. I captured a JRA this morning setting nativesamples=true.
I see the following when I look at the Hot Methods - let me know if there is something else that would shed some more light on this issue.
Method Percent(%) #Samples Optimized Native Method Id.
libjvm.so#mmDetGcFollowReferencesWorkers 28.575 2,062 0 1 0x2AE6B82EC2C1
libpthread.so.0#__recvfrom_nocancel 26.012 1,877 0 1 0x3CC1A0D689
libpthread.so.0#__accept_nocancel 26.012 1,877 0 1 0x3CC1A0D4A9
libjvm.so#mmBalanceGetReference 4.975 359 0 1 0x2AE6B817A65B
libjvm.so#objIterStepFieldFromBitmaskWord 4.753 343 0 1 0x2AE6B82A6B34
libjvm.so#objIterStep 3.88 280 0 1 0x2AE6B82A6F8D
libjvm.so#objIterInitInner 2.744 198 0 1 0x2AE6B82A71B7
libjvm.so#mmBalanceStoreReference 1.414 102 0 1 0x2AE6B817A781
libjvm.so#objIterSetupFields 0.637 46 0 1 0x2AE6B82A6B08
libjvm.so#nativeInnerLockNotLinked 0.236 17 0 1 0x2AE6B829DE76
libjvm.so#mmWorkPacketPoolGet 0.125 9 0 1 0x2AE6B817A4F5
libjvm.so#qBitSetIsBitSetInWord 0.069 5 0 1 0x2AE6B82C8AA6
libjvm.so#nativeInnerUnlockNotLinked 0.069 5 0 1 0x2AE6B829E028
libjvm.so#mmWorkPacketPoolAdd 0.042 3 0 1 0x2AE6B817A48E
libjvm.so#objPoolMarkAllHard 0.042 3 0 1 0x2AE6B82A4923
libjvm.so#objIterSetupArray 0.028 2 0 1 0x2AE6B82A6BDB
libjvm.so#markAcquired 0.028 2 0 1 0x2AE6B829DBD3
libjvm.so#mmPointerMatrixTryInsertAtIndex 0.028 2 0 1 0x2AE6B82BEFEB
libjvm.so#mmPointerMatrixClear 0.028 2 0 1 0x2AE6B82BF61C
libjvm.so#objPoolMarkWeakConcurrently 0.028 2 0 1 0x2AE6B82A5358
libjvm.so#qBitSetFindFirstNonClearedWord 0.014 1 0 1 0x2AE6B82C888E
libjvm.so#utilCounterToNanos 0.014 1 0 1 0x2AE6B8313B53
libjvm.so#waitForLockIfNeededAndMarkAcquired 0.014 1 0 1 0x2AE6B829DC30
libjvm.so#vmtLinkData 0.014 1 0 1 0x2AE6B8325B2E
libjvm.so#mmBitsIsObjectMarkedGrey 0.014 1 0 1 0x2AE6B82ED7E9
libjvm.so#qBitSetFindLastSetBitInWord 0.014 1 0 1 0x2AE6B82C8854
libjvm.so#mark_writebarriers 0.014 1 0 1 0x2AE6B8250EEA
libjvm.so#signalNextInLockQueueIfNeeded 0.014 1 0 1 0x2AE6B829DF52
libjvm.so#mmGetUsingMatrixes 0.014 1 0 1 0x2AE6B819F33C
libjvm.so#ptGetThreadId 0.014 1 0 1 0x2AE6B82BD9ED
libc.so.6#memset 0.014 1 0 1 0x3CC0A7A000
libjvm.so#setupNodeForSelf 0.014 1 0 1 0x2AE6B829DD87
libc.so.6#_int_free 0.014 1 0 1 0x3CC0A714E0
libjvm.so#mmAddChunkToList 0.014 1 0 1 0x2AE6B830977C
libjvm.so#vmtiUnlinkData 0.014 1 0 1 0x2AE6B8325B4A
libjvm.so#nativeLockInSuspendCritical 0.014 1 0 1 0x2AE6B829E0E3
libjvm.so#mmSweepHeapPart 0.014 1 0 1 0x2AE6B830989A
libjvm.so#mmBalanceWorkSetSwapPackets 0.014 1 0 1 0x2AE6B817A647
libc.so.6#_int_malloc 0.014 1 0 1 0x3CC0A71E80
libjvm.so#charToJlcType 0.014 1 0 1 0x2AE6B8253633
unknown#unknown functions 0 0 0 1 0x2AE6B8597090
Running with nativemethods=false, I see the following under hot methods
Method Percent(%) #Samples Optimized Native Method Id.
jrockit.vm.Locks.monitorExitSecondStage(Object) 50 1 1 0 0x161D30D0
com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService.onNotify() 50 1 1 0 0x169D2C70
com.tangosol.coherence.component.util.daemon.queueProcessor.packetProcessor.PacketReceiver.onNotify() 0 0 1 0 0x1551C050
com.tangosol.coherence.component.util.queue.ConcurrentQueue.checkFlush(int) 0 0 1 0 0x151C2180
java.lang.Thread.run() 0 0 0 0 0x14E98EB0
jrockit.vm.RNI.c2java(long, long, long, long, long) 0 0 0 0 0x14C07830
unknown#unknown functions 0 0 0 1 0x2AE6B8597090
com.tangosol.coherence.component.util.Daemon.run() 0 0 0 0 0x15CFEBC0
com.tangosol.coherence.component.util.queue.ConcurrentQueue.add(Object) 0 0 1 0 0x15ED6B00
com.tangosol.coherence.component.util.queue.ConcurrentQueue.onAddElement() 0 0 1 0 0x151C9C20
com.tangosol.coherence.component.util.queue.ConcurrentQueue.flush(boolean) 0 0 1 0 0x1618CAD0
Thanks,
Jason -
High CPU Usage with Flash Player 11
I am not sure what the problem is but ever since I had those issues I went back to flash archive and installed a previous version that did not come with the flash plug in and I never had any problem with it since I am currently using the Adobe flash version 10 plug in with an adobe flash player active X. and I find out it was the new flash plug in that is the issue it suck all your ram. If you get some people who is having the same issues where flash player is duplicating and eating all their ram then ask them to try the version 10 plug in with the flash 11 active x it will work fine. I tried to run the version 10 flash as a complete set but some dynamic site that plays videos require a later version of flash active x to work and will be asking for an update however by keeping the flash 10 plug in there won't be any other issues. Adobe need to find out what is wrong with the new flash plug in and run a comparison with the flash 10 plug in. I hope this will help some user to get over the issues that made my online experience a nightmare for a while too.
The best way to get a resolution is to address your individual issue. Your complaint is that RAM usage is high, which is unrelated to the thread from the guy on Mac that was seeing High CPU usage on high definition video.
In order to fix the issue that you're describing, we need to be able to reproduce it. Please provide the information below, and the results of the basic troubleshooting steps as you work through them. This will help us narrow down the root-cause, and allow us to find comparable hardware in our compatibility lab to reproduce the issue with.
Basic Troubleshooting Info
To help troubleshoot we'll need the following system information:
- Operating system
- Browser
- Flash Player version - http://helpx.adobe.com/flash-player/kb/find-version-flash-player.html
- Antivirus/Anti-Malware software and versions
The first step is to work through the video troubleshooting guide for your operating system, here:
- Windows - http://helpx.adobe.com/flash-player/kb/video-playback-issues.html
- Mac - http://helpx.adobe.com/flash-player/kb/video-playback-issues.htm
When reporting issues with video or audio, it's also helpful to get your system hardware and driver details. Instructions for finding this information can be found here:
- Windows - http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_For_Windows_users
- Mac - http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_For_Mac_OS_users
Finally, sometimes video and audio problems are caused at a lower level and not directly related to Flash Player. I recommend trying both of the links below to see how they perform. If the problem exists with both, then Flash Player is most likely not the culprit as the HTML5 video link does not use Flash Player when playing. You can verify this by right clicking the HTML5 video and looking for the words "About HTML5" at the bottom of the menu.
- HTML5 video - http://www.youtube.com/watch?v=cTl3U6aSd2w&html5=True
- Non-HTML5 video - http://www.youtube.com/watch?v=cTl3U6aSd2we
Thanks! -
EA2: high CPU usage with large packages
EA2 + Debian GNU/Linux + jdk1.6.0_04 + Pentium IV 2,8 GHz 1 GBytes RAM
Opening large packages (> 6.000 rows) I have high CPU usage (100%) for about 50-60 seconds. Same problem when I working with these packages
Ciao
DavideOpening works fine for me, and memory seems to be
contained. Working inside the package on occasions
still boosts CPU like you.Attempting to edit an 800 line type body utilises 100% CPU as soon as typing starts.
Windows XP Professional SP2
Oracle Server 10.2.0.3
Java 1.5.0_06
Intel Pentium M 1.69GHz 2GB RAM -
Unusually high cpu usage with iMovie 6.0.3
I'm having trouble with very high cpu-usage. Just the open imovie app is taking up about 50%, during playback it sometimes peaks over 100%! The project file is pretty big (about 30 gig), but that is mainly because of the amount of footage imported into it. The movie itself is about 25 minutes in length. There is some audio editing going on: some soundeffects, musicfiles (no drm-protection), audio commentary that i recorded within imovie. I know that imovie has trouble when there is a lot of audio/audio editing involved and this project is probably a little more complex than other stuff i did in imovie, but i never had such problems. i can hardly use playback anymore. I recently updated Quicktime to 7.6.4 and Perian to version 1.2.1. Any ideas what's going on or how to work around the problems? Since the movie is about 80% finished i don't really want to start all over again. Thanks in advance for your input!
Hi Klaus1
I have several plug-ins by cfx and the slick volumes 4, 6 8 and 10. I can post a list of all of them if you like. Up to now they never made any trouble, but you'll never know...
The edit in the timeline is about 25 minutes long. But the project file contains captured dv-footage of about 2 hours, so that alone adds up to something like 26 GB. Then there are a few rendered effect-clips done with some of the plug-ins like stabilizing or color correction which also add to the 30 GB, as well as some audio-files (some music, my voice-over commentary). I emptied the trash several times while working on the movie. At this moment there are only a few MB of erased audio in it.
It all sounds a bit like this is an insanely huge and complex project, but as i said, i have done projects like this in imovie without the massive cpu-usage. I'd like to continue to use imovie, but if this problem keeps coming up with future projects, i might as well take the step and switch to Final Cut Express.
For now I will try your idea of exporting the movie as it is now and open it in a new project file.
Thanks for your help and input so far! -
High CPU usage when playing flv files with flash
As more and more FLV videos are moving to HD, I'm noticing
high CPU usage and lots of dropped frames when playing FLV video in
web browser with Flash 10. This is true even if the video isn't
full screen. I've tried a variety of browsers (Firefox, I.E.,
Chrome) and the problem occurs on all of them so it's pretty clear
it's a limitation in Flash.
Now my PC isn't high end (it has a Pentium M 1.86 GHz
processor), but I can take those same FLV files and load them in
something like Media Player Classic or Windows Media Player (when
using ffdshow) and play the FLV files full screen with little or no
drop in frames and an acceptable CPU rate.
This is especially annoying on sites like YouTube where I
actually have to save the video and play it back in something other
than Flash to have it play back at an acceptable rate. This doesn't
work for other sites like Amazon.
Why is the CPU usage so high when decoding and displaying
videos when compared to other media players?I've been doing research about this excessively high CPU usage problem (100%!) for weeks because I have also experienced it with my vista home premium laptop. Just recently, I have finally found the solution. The problem is not your browser or your OS or your pc's memory. The problem is caused by authorization for flash player.
Read the link (posted below) carefully and follow the steps accordingly. If you have already done steps 1 through 6 with your computer, you can go straight to step 7.
http://thetechangel.com/blogberry/2008/10/adobe-flash-player-10-fix-for-vista-xp/
PS: I am not the author of that link, so please thank the respective site owner if you find the procedure very helpful.
Please let me know also if the link solves your problem. I am sharing this because Adobe seems unable to provide solutions to this, and I don't want to hear people suffer.
My blog:
http://literaryworks101.blogspot.com
http://bookofsalamat.blogspot.com
Thanks -
[help] high cpu usage with flash (Hello adobe developer)
Running youtube or facebook games, here's what I found. CPU usage rises to 90-100% or 90-100 % of a core.
Tested in XP32/Win7 64. Clean setups. Tested with Flash 9, 10, 10.1 rc's. Used uninstallers, reinstalled and so on. Googled on this, read many threads, such as granting permission on several files. Tested with IE, Firefox, Chrome. SAME stuff. Tested on an e8400 with P35 chipset, i3 530 with P55 chipset, e7400 with nvidia ion chipset, tested with 7[3|6]00gt's, gts 250.. So yes, I've tried a lot of things. And many different drivers too. I am now only pointing fingers at flash.
PC gets sluggish, laptops run out of battery fast. I can usually fix a lot of technicals issues on my own, but I'm TOTALLY stuck here. I should also add that, cpu usage rises only when there is motion. I can watch an .avi movie or play some 3D game, and they won't suck the cpu totally. I can remember in the past, flash won't do this. Flash won't drag the system down. Something is SERIOUSLY wrong.
Can an Adobe dev comment please?I find it strangely odd that you've never seen this phenomenon, but at least you must have heard of it. Google flash high cpu usage. Facebook games flash lag. Or something alike. Mind moving my thread there? So there won't be a dupe thread.
I posted a similar thread in mozilla forums to see what they have to see, since i notice lag is more apparent in firefox than in ie, although both hog up cpu.
As you can see, I'm not alone.
http://forums.mozillazine.org/viewtopic.php?f=38&t=1913819
My installation _of_ what? Let's see, I tried to replicate this in the most bare environment. With nothing else installed, and default Windows 7 drivers, I installed flash from the web, plugin only first, then activex, did the testing, same stuff. Installed OLD 183 drivers, tested with 197 drivers, then 256 beta drivers. Same deal. -
High CPU usage: Animation with background
I experience a high CPU usage when animating a shape over a background. If I disable the background or the animation, the CPU usage drops to almost zero. It seems like the combination of background shapes and an animated shape is very costly.
Is there a way to improve this performance? Can I indicate that the animated shape is always on top? Adding the smooth and cache tags did not improve the performance.
Thanks in advance.
import javafx.stage.Stage;
import javafx.scene.Scene;
import javafx.animation.Interpolator;
import javafx.animation.*;
import javafx.animation.transition.*;
import javafx.scene.shape.Rectangle;
import javafx.scene.paint.Color;
var nBackgrounds = 20;
var screenWidth = 1024;
var screenHeight = 800;
def animatingRectangle = Rectangle{
width: screenWidth
height: screenHeight
fill:Color.BLUE
def background = for(i in [1..nBackgrounds]) Rectangle{
width: screenWidth
height: screenHeight
fill:Color.RED
def liveView:Scene = Scene {
width: screenWidth
height: screenHeight
content: [
background,
animatingRectangle,
] // content
} // Scene
Stage {
title: "Example"
scene: liveView
} // Stage
var fakeImageTransition:TranslateTransition = TranslateTransition {
fromY: bind animatingRectangle.translateY
toY: bind -screenHeight
duration: 10s
node: animatingRectangle
interpolator : Interpolator.EASEOUT
framerate: 30
repeatCount:50
fakeImageTransition.playFromStart();I'm having the same issue. I have 4gb of ram and all of it will be in use even with just Safari running. High fan use. When this happens video will stutter.
-
High CPU usage with no reason after upgrade to 10.6
One of screenshots:
http://www.flickr.com/photos/vlaza/3893077851/I'm having the same issue. I have 4gb of ram and all of it will be in use even with just Safari running. High fan use. When this happens video will stutter.
-
Incredibly high CPU usage with Flash plugin
Hi all,
I'm using Safari 4.0.3 with the last Flash Plugin version (10.0.32.18) that I just uninstalled and then reinstalled, and I got an incredibly high cpu usage while viewing an Youtube video.
Here is a screenshot of Activity monitor that shows you the percentage.
http://img256.imageshack.us/img256/7186/schermata20091106a13590.png
Sometimes the Safari process reach even 50% while the FlashPlugin one runs at 110%-120%.
Is that normal? With other browsers like Camino or Firefox, the CPU usage for the same video drops to 50%-60% max.
Thank you,
Silentheaven
Message was edited by: SilentheavenHI,
Try here.
http://rentzsch.github.com/clicktoflash/
Block evil Adobe Flash
Flash only when you want it.
One-click Flash loading
View blocked Flash with just one click.
Higher quality YouTube
Play videos in QuickTime, not Flash.
Website Whitelist
Allow Flash on certain websites.
*Lowered CPU usage*
Browse the web more quickly.
Better battery life
Browse the web longer on your laptop.
Less fan usage and heat
Browse the web quietly and cooly.
Automatic Updating
Download updates when they're ready.
Carolyn
Maybe you are looking for
-
Idiotic Basic Question - making a circle with transparent bg driving me nuts!
OK, disclaimer - I have been using an old version of elements and just upgraded to Photoshop CS5 Extended. All I want to do is: 1) Create a circle for a logo. 2) Add text and drop shadow. 3) Make bg transparent. Why am I getting the white line ar
-
Why cannot control iPhone through USB in Honda or Yamaha
My wife and I have two iPhone 5s and two iPads at 8.1.3 that can no longer be controlled when plugged into usb devices such as my 2014 Honda Odyssey and my Yamaha receiver. The song titles appear and I can scroll but will not play the music after cl
-
HDMI - DVI Adapter for AppleTV
It is clear after speaking to Apple Support today that the new Apple TV will not work with conventional HDMI to DVI adapters. If anyone finds a workaround please post your solution to this thread. Thanks!
-
Mic Problems- With Audigy ZS, the one with the external Sound ca
hi i brought this sound card about a year ago and just been using it for recording using line3, but now i want to use a mic, and so i plub in a mic into line/mic and all i get is static, so i plug into line2 and i fully yell just to hear a wisper, wh
-
Exit from dataforwardAction without refresh control for Binding Container
Sir's months ago i posted ADF Struts life clycle and i though that i had corrected my problem. but last Friday analyzing my bc4j log file i realize that my bindingContainer is still executing my views objects queries; What i want, is just exit from a