High cpu when change "mls cef maximum-route ip" to more than 512K

Dear All
From cisco document 6500-sup720 and 7600-rsp720 are support IPv4 unicast and MPLS—512,000 routes by default. On my network we have route more than 400K which nearly reach to the limit then I tried to change from 512K to 1007K as below.
Router#sh mls cef maximum-routes
FIB TCAM maximum routes :
=======================
Current :-
IPv4                - 1007k
MPLS                - 1k
IPv6 + IP Multicast - 8k (default)
After rebooted I got high cpu issue on both 6500-sup720 and 7600-rsp720 then I tried to tuning to other value such as 600K , 700K and so on but doesn't help.
Summary
   - I have no cpu issue with default value for mls cef maximum-route
   - I have cpu issue when tuning to other value such as 600K , 700K
Please advise.
Pichet

Similar Messages

Cisco 7606 FIB Protocol Allocation mismatch after mls cef maximum-routes command

Hi,
we are trying to fine tune the mls cef maximum-routes without success for ipv4 on our Cisco 7606 router equiped like this:
Mod Ports Card Type Model Serial No.
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL09169CP0
6 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL10370YH7
Mod MAC addresses Hw Fw Sw Status
2 0013.c38b.ed9c to 0013.c38b.edb3 2.2 12.2(14r)S5 12.2(33)SRC1 Ok
6 0017.9441.b750 to 0017.9441.b753 5.2 8.4(2) 12.2(33)SRC1 Ok
Mod Sub-Module Model Serial Hw Status
2 Centralized Forwarding Card WS-F6700-CFC SAL09159C8T 2.0 Ok
6 Policy Feature Card 3 WS-F6K-PFC3BXL SAL10360CJ0 1.8 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL10360GNX 2.5 Ok
the show version is like this:
System image file is "bootdisk:c7600s72033-adventerprisek9-mz.122-33.SRC1.bin"
We tryied to set the value of the ipv4 FIB TCAM to 720k with this command:
mls cef maximum-routes ip 720
and then to save the configuration we used the "write" command. This was the output after we wrote the configuration:
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
Upon reboot :-
IPv4 - 720k
MPLS - 16k (default)
IPv6 + IP Multicast - 144k (default)
so we reloaded the router to get the new value.
when the router was up again it start to reload each 4 minutes. The FIB TCAM value was:
show mls cef maximum-routes
Reload scheduled for 13:50:09 DST Wed Aug 13 2014 (in 2 minutes and 51 seconds)
Reload reason: FIB Protocol Allocation mismatchFIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
User configured :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
Upon reboot :-
IPv4 + MPLS - 512k (default)
IPv6 + IP Multicast - 256k (default)
We know that our cisco is able to handle up to 1M of ipv4 routes inside the TCAM but we cannot set more than 512k ipv4 routes.
Why the router doesn't accept the new value?
Thanks
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/116132-problem-catalyst6500-00.html
https://supportforums.cisco.com/discussion/12250356/recommended-value-7600-ipv4-fib-tcam

Hi Paolo,
#sho ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 04:53 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
punk.gs2 uptime is 17 hours, 55 minutes
Uptime for this control processor is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 54 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014 (SP by reload)
System restarted at 22:35:24 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C6504-E (R7000) processor (revision 2.0) with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
11 Virtual Ethernet interfaces
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
#remote command switch show version
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 11-Mar-14 05:09 by prod_rel_team
ROM: System Bootstrap, Version 8.5(4)
punk.gs2 uptime is 17 hours, 55 minutes
Time since punk.gs2 switched to active is 17 hours, 55 minutes
System returned to ROM by reload at 22:32:30 BST Mon Sep 1 2014
System restarted at 22:34:17 BST Mon Sep 1 2014
System image file is "disk0:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: Reload Command
cisco Catalyst 6000 (R7000) processor with 983008K/65536K bytes of memory.
Processor board ID FOX11270F1B
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
50 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
500472K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Hope that helps.

My macbook pro i7 (2011 version) has a loud fan and high cpu % when I have Skype on or when I am on Safari. Help please!

My macbook pro i7 (2011 version) has a loud fan and a high cpu % when I have Skype on or when I am on Safari. My laptop would sometimes freeze for a while and it is usually hot. Has anyone else encounter this problem and know how to fix it? Thanks!

Skype is a very resource intensive activity...it has been reported on here users are seeing cpu temperatures on the order of 80-85 °C, within the limits of the cpu, but still hot to the touch.
Make sure nothing else is running so you keep the thermal load down.

Changing the Window Color of an JInternalFrame more than once

I want to change the color of an JInternalFrame when it was created. This could be more than once.
I know that i can use:
UIManager.put("InternalFrame.activeTitleBackground", Color.RED);
but this code only takes effect before the InternalFrame is createt

You are using iPhoto 9 (11)? If you are then the themes would be obvious when you select iPhoto as your mail client in iPhoto's General preference pane (upper left hand image)
Click to view full size
and then use the Share ➙ Email button
Click to view full size
to get this window:
Click to view full size
However, I was mistaken in that the background colors for those themes can't be changed. The same goes for the stationary themes in Mail.

When i try to send a message to more than 1 person it tries to go out and comes up in the blue box but is not delivered?

When I try to send a message to more than one person it tries to go out and comes up in the blue box but is not delivered. I phone 4s?

Hello blee136,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Troubleshooting Messages
http://support.apple.com/kb/TS2755
Best of luck,
Mario

How many sign-on's are included when I purchase Photoshop and Illustrator? Can more than one person have access on separate computers?

How many sign-on's are included when I purchase Photoshop and Illustrator? Can more than one person have access on separate computers?

You have 2 activations and the licenses is tied to you personally and you only. You cannot let other people use your software (unless they are family).
Mylenium

Why does Lightroom 4.3 use very high cpu when waiting for user to click OK?

I saved metadata for 52 photos.
Lightroom 4.3 couldn't save metadata for 2 of the photos and opened a window to tell me so. (It had no problem saving metadata on second attempt.)
While it waited for my response and wasn't doing any work, it was using over 50% of my CPU.
Why?
Windows 7 is 32-bit Professional.
Processor: Intel Core i5 750 Processor 2.66 GHz
Here's my system info as reported by Lightroom.
Lightroom version: 4.3 [865747]
Operating system: Windows 7 Business Edition
Version: 6.1 [7601]
Application architecture: x86
System architecture: x86
Logical processor count: 4
Processor speed: 2.7 GHz
Built-in memory: 3579.4 MB
Real memory available to Lightroom: 716.8 MB
Real memory used by Lightroom: 710.9 MB (99.1%)
Virtual memory used by Lightroom: 847.9 MB
Memory cache size: 2.0 MB
Maximum thread count used by Camera Raw: 4
System DPI setting: 96 DPI
Desktop composition enabled: Yes
Displays: 1) 1920x1080
Application folder: C:\Program Files\Adobe\Adobe Photoshop Lightroom 4.3
Library Path: D:\Users\Calvin\Pictures\My Lightroom\lightroom\lightroom4\lightroom4.lrcat
Settings Folder: C:\Users\Calvin\AppData\Roaming\Adobe\Lightroom
Adapter #1: Vendor : 10de
    Device : 640
    Subsystem : c9593842
    Revision : a1
    Video Memory : 1007
AudioDeviceIOBlockSize: 1024
AudioDeviceName: Speakers (Realtek High Definition Audio)
AudioDeviceNumberOfChannels: 2
AudioDeviceSampleRate: 44100
Build: Uninitialized
Direct2DEnabled: false
GL_ALPHA_BITS: 0
GL_BLUE_BITS: 8
GL_GREEN_BITS: 8
GL_MAX_3D_TEXTURE_SIZE: 2048
GL_MAX_TEXTURE_SIZE: 8192
GL_MAX_TEXTURE_UNITS: 4
GL_MAX_VIEWPORT_DIMS: 8192,8192
GL_RED_BITS: 8
GL_RENDERER: GeForce 9500 GT/PCIe/SSE2
GL_SHADING_LANGUAGE_VERSION: 3.30 NVIDIA via Cg compiler
GL_VENDOR: NVIDIA Corporation
GL_VERSION: 3.3.0
OGLEnabled: true
OGLPresent: true
GL_EXTENSIONS: GL_ARB_arrays_of_arrays GL_ARB_base_instance GL_ARB_blend_func_extended GL_ARB_clear_buffer_object GL_ARB_color_buffer_float GL_ARB_compatibility GL_ARB_compressed_texture_pixel_storage GL_ARB_conservative_depth GL_ARB_copy_buffer GL_ARB_copy_image GL_ARB_debug_output GL_ARB_depth_buffer_float GL_ARB_depth_clamp GL_ARB_depth_texture GL_ARB_draw_buffers GL_ARB_draw_elements_base_vertex GL_ARB_draw_instanced GL_ARB_ES2_compatibility GL_ARB_ES3_compatibility GL_ARB_explicit_attrib_location GL_ARB_explicit_uniform_location GL_ARB_fragment_coord_conventions GL_ARB_fragment_layer_viewport GL_ARB_fragment_program GL_ARB_fragment_program_shadow GL_ARB_fragment_shader GL_ARB_framebuffer_no_attachments GL_ARB_framebuffer_object GL_ARB_framebuffer_sRGB GL_ARB_geometry_shader4 GL_ARB_get_program_binary GL_ARB_half_float_pixel GL_ARB_half_float_vertex GL_ARB_imaging GL_ARB_instanced_arrays GL_ARB_internalformat_query GL_ARB_internalformat_query2 GL_ARB_invalidate_subdata GL_ARB_map_buffer_alignment GL_ARB_map_buffer_range GL_ARB_multisample GL_ARB_multitexture GL_ARB_occlusion_query GL_ARB_occlusion_query2 GL_ARB_pixel_buffer_object GL_ARB_point_parameters GL_ARB_point_sprite GL_ARB_program_interface_query GL_ARB_provoking_vertex GL_ARB_robust_buffer_access_behavior GL_ARB_robustness GL_ARB_sampler_objects GL_ARB_seamless_cube_map GL_ARB_separate_shader_objects GL_ARB_shader_bit_encoding GL_ARB_shader_objects GL_ARB_shader_texture_lod GL_ARB_shading_language_100 GL_ARB_shading_language_420pack GL_ARB_shading_language_include GL_ARB_shading_language_packing GL_ARB_shadow GL_ARB_stencil_texturing GL_ARB_sync GL_ARB_texture_border_clamp GL_ARB_texture_buffer_object GL_ARB_texture_buffer_range GL_ARB_texture_compression GL_ARB_texture_compression_rgtc GL_ARB_texture_cube_map GL_ARB_texture_env_add GL_ARB_texture_env_combine GL_ARB_texture_env_crossbar GL_ARB_texture_env_dot3 GL_ARB_texture_float GL_ARB_texture_mirrored_repeat GL_ARB_texture_multisample GL_ARB_texture_non_power_of_two GL_ARB_texture_query_levels GL_ARB_texture_rectangle GL_ARB_texture_rg GL_ARB_texture_rgb10_a2ui GL_ARB_texture_storage GL_ARB_texture_storage_multisample GL_ARB_texture_swizzle GL_ARB_texture_view GL_ARB_timer_query GL_ARB_transpose_matrix GL_ARB_uniform_buffer_object GL_ARB_vertex_array_bgra GL_ARB_vertex_array_object GL_ARB_vertex_attrib_binding GL_ARB_vertex_buffer_object GL_ARB_vertex_program GL_ARB_vertex_shader GL_ARB_vertex_type_2_10_10_10_rev GL_ARB_viewport_array GL_ARB_window_pos GL_ATI_draw_buffers GL_ATI_texture_float GL_ATI_texture_mirror_once GL_S3_s3tc GL_EXT_texture_env_add GL_EXT_abgr GL_EXT_bgra GL_EXT_bindable_uniform GL_EXT_blend_color GL_EXT_blend_equation_separate GL_EXT_blend_func_separate GL_EXT_blend_minmax GL_EXT_blend_subtract GL_EXT_compiled_vertex_array GL_EXT_Cg_shader GL_EXT_depth_bounds_test GL_EXT_direct_state_access GL_EXT_draw_buffers2 GL_EXT_draw_instanced GL_EXT_draw_range_elements GL_EXT_fog_coord GL_EXT_framebuffer_blit GL_EXT_framebuffer_multisample GL_EXTX_framebuffer_mixed_formats GL_EXT_framebuffer_multisample_blit_scaled GL_EXT_framebuffer_object GL_EXT_framebuffer_sRGB GL_EXT_geometry_shader4 GL_EXT_gpu_program_parameters GL_EXT_gpu_shader4 GL_EXT_multi_draw_arrays GL_EXT_packed_depth_stencil GL_EXT_packed_float GL_EXT_packed_pixels GL_EXT_pixel_buffer_object GL_EXT_point_parameters GL_EXT_provoking_vertex GL_EXT_rescale_normal GL_EXT_secondary_color GL_EXT_separate_shader_objects GL_EXT_separate_specular_color GL_EXT_shadow_funcs GL_EXT_stencil_two_side GL_EXT_stencil_wrap GL_EXT_texture3D GL_EXT_texture_array GL_EXT_texture_buffer_object GL_EXT_texture_compression_dxt1 GL_EXT_texture_compression_latc GL_EXT_texture_compression_rgtc GL_EXT_texture_compression_s3tc GL_EXT_texture_cube_map GL_EXT_texture_edge_clamp GL_EXT_texture_env_combine GL_EXT_texture_env_dot3 GL_EXT_texture_filter_anisotropic GL_EXT_texture_integer GL_EXT_texture_lod GL_EXT_texture_lod_bias GL_EXT_texture_mirror_clamp GL_EXT_texture_object GL_EXT_texture_shared_exponent GL_EXT_texture_sRGB GL_EXT_texture_sRGB_decode GL_EXT_texture_storage GL_EXT_texture_swizzle GL_EXT_timer_query GL_EXT_vertex_array GL_EXT_vertex_array_bgra GL_EXT_import_sync_object GL_IBM_rasterpos_clip GL_IBM_texture_mirrored_repeat GL_KHR_debug GL_KTX_buffer_region GL_NV_blend_square GL_NV_conditional_render GL_NV_copy_depth_to_color GL_NV_copy_image GL_NV_depth_buffer_float GL_NV_depth_clamp GL_NV_ES1_1_compatibility GL_NV_explicit_multisample GL_NV_fence GL_NV_float_buffer GL_NV_fog_distance GL_NV_fragment_program GL_NV_fragment_program_option GL_NV_fragment_program2 GL_NV_framebuffer_multisample_coverage GL_NV_geometry_shader4 GL_NV_gpu_program4 GL_NV_half_float GL_NV_light_max_exponent GL_NV_multisample_coverage GL_NV_multisample_filter_hint GL_NV_occlusion_query GL_NV_packed_depth_stencil GL_NV_parameter_buffer_object GL_NV_parameter_buffer_object2 GL_NV_path_rendering GL_NV_pixel_data_range GL_NV_point_sprite GL_NV_primitive_restart GL_NV_register_combiners GL_NV_register_combiners2 GL_NV_shader_buffer_load GL_NV_texgen_reflection GL_NV_texture_barrier GL_NV_texture_compression_vtc GL_NV_texture_env_combine4 GL_NV_texture_expand_normal GL_NV_texture_multisample GL_NV_texture_rectangle GL_NV_texture_shader GL_NV_texture_shader2 GL_NV_texture_shader3 GL_NV_transform_feedback GL_NV_vertex_array_range GL_NV_vertex_array_range2 GL_NV_vertex_buffer_unified_memory GL_NV_vertex_program GL_NV_vertex_program1_1 GL_NV_vertex_program2 GL_NV_vertex_program2_option GL_NV_vertex_program3 GL_NVX_conditional_render GL_NVX_gpu_memory_info GL_SGIS_generate_mipmap GL_SGIS_texture_lod GL_SGIX_depth_texture GL_SGIX_shadow GL_SUN_slice_accum GL_WIN_swap_hint WGL_EXT_swap_control

I don't think so.
I have enough experience with LR to know what to expect for various activities.
Previews for all photos had been rendered long before I initiated the Save Metadata.
Metadata for 50 of the 52 files had already been written.
The high cpu had gone on for at least 5 minutes.   I switched to another app imediately after initiating the Save Metadata for the 52 files and only went back to LR when I heard my CPU fan running for a long time.
When I got back to LR, I saw the "Could not save metadata" window. I clicked "Show in Library" and OK. As soon as I did that, CPU usage went back to normal.
I've experienced the exact same scenario, where LR can't save metadata for all photos and I've never had LR get stuck consuming a very large amount of CPU.
As a test, I selected 118 other photos, changed metadata for all of them and then selected all and saved metadata. LR took about 20 seconds to save metadata for all 118 and LR CPU usage never went above 17%. The difference is that LR did not show the "Could not save metadata" window.

High CPU when playing Minecraft

My MacBook Pro Retina Core i5 8GB RAM has abou 100% and more usage when playing and my cooling is loud, what to do?

I have searched all over the web too to find any solutions regarding the unavoidable problem of Macs with Adobe's Flash Player. There are little improvements of reducing the high CPU during Flash use on a Mac through changing your main browser to Opera, Camino ... BUT it is still a problem which cannot be solved for now. The following URL is from Adobe's Bug Website and explains exactly what is wrong with Flash on a Mac:
Very High CPU usage and thus High Fan speed.
https://bugs.adobe.com/jira/browse/FP-890
Here's another link to a similar problem in the Apple Discussions:
http://discussions.apple.com/thread.jspa?messageID=8920577
And finally the comparison of CPU usage between Mac and Windows which shows very clear that there's obviously something MAJOR not working and Adobe has to fix it!
http://arstechnica.com/software/news/2008/10/benchmarking-flash-player-10.ars
It is a shame that this problem is out for years and Adobe is NOT trying to fix it, or at least not as intense as they should. So this is the reason why many people all over the world have to live with their Mac running high fan and a hot CPU when just browsing the internet.

High CPU when Inactive?

Hi,
I am happy with my Mac Air but have noticed a problem & would welcome any ideas on how I diagnose this?
I normally use Safari, Email & a number of other open apps - and CPU jumps between 4-20%; this to me seems normal.
However, if I leave the Mac Air unattended; the screen saver comes on as it should - however, I notice after a few more minutes the fan comes on & if I then tab a key to bring out of screensaver - I see the CPU at 93-98%. Within a few seconds it reverst to normal (4-20%) and fan stops.
I have left the laptop for 30mins+ but can hear the fan continuous - only stops when I touch a key.
Ps, the screensaver is just the default & screen turns off after 15mins - yet high cpu seems to kick in whenever the laptop is inactive)
Any ideas?
Cheers,
T

OK - I know this is an old topic, but I finally figured out what was causing my CPU spikes. It turns out the offending process was "mscorsvw.exe", which compiles .NET assemblies in the background while my computer is idle: http://blogs.msdn.com/b/davidnotario/archive/2005/04/27/412838.aspx
Running the command "ngen.exe executequeueditems" cleared up the problem.

X high CPU when using Java applications

Only recently, my Freemind program has become extremely sluggish and unresponsive (big lag) when moving my mind map around. Freemind is made with Java. If I move the mind map around, the X process shoots to 20% CPU, doesn't seem a lot but something between X and Java programs are really bringing their performance down.
I can barely use Freemind now. Freeplane is also affected.
I noticed if I keep the Freemind window really small, it's responsive. If I maximise it, everything slows down within the application. Adding new notes, or move the map around, shoots X to a high CPU and there is a 5+ second lag in anything I do in the app.
Is there anything I can do to improve performance? It's only started recently, everything is up-to-date.
Last edited by nLinked (2013-06-08 13:57:31)

Hi
Try to use -Xloggc parameter with the jvm in order to see if problem comes on garbage colector. May be the mem usage is little and the gc thread is in active state. Try, also modify the mem usage with -Xms and -Xmx parameters and see the gc efects.
You can use the -Xprof to output cpu profiling data.
Also, find if there is a bug on servlet container / hard /SO you are using.
Hope this helps

Firefox uses high cpu when playing online flash games like farmville in facebook

Whenever i open games in facebook, firefox uses up high CPU. I tried to install older version of firefox, new version everything has the same problem. There could be some compatibility issue with the adobe flash and firefox.
I am sure that some version works well, because i never had this problem before. Yesterday i had to re-install my XP and after re-install suddenly this issue started, which means this can be solved with proper versions of firefox and flash which i used before.
Please help!!!!!!!

After I made sure I was running latest FireFox and Flash, I started disabling add-ons. It appears right now that Flashblock is the culprit, at least for me. If you have that, try disabling it.
Also, most of those Facebook flash games have some serious problems with memory leaks and bad programming. Is your problem specific to Facebook games or all flash games?

My iPhone5 has terrible Network connection. It rarely works at the normal speed-if ever. I usually get 3G or 1x network dozens of times a day. My phone also gets pretty hot when i try to use any data for more than a few minutes.

My iPhone5 network connection has been terrible for the past week and a half. My phone is no more than a year old so I don't see why it would be a problem with the phone. When I try to use the internet or look for apps or anything like that, anything that uses data really, it takes FOREVER if it even loads! Most of the time it won't even load. My network changes from LTE(which doesn't work well) to 3G(which works even less) and then to 1x(which basically doesn't work at all). This happens dozens of times a day. It's getting quite irritating. I've tried turning my phone off and letting it sit for a while and that does nothing. I'd really prefer NOT to restore my phone. What is the deal??!

Are you broadcasting your SSID? Sometimes this can cause a problem connecting. Is this Cisco router running any turbo modes or special preparatory protocols.
There are no know issues with Wi-Fi connectivity except on first connection; and the chance of 2 devices having the exact same issue is very unlikely. This sounds like something to do with your wireless router.
Have you tried to connect to another Wi-Fi hotspot elsewhere?
Do you have any 2.4 GHz wireless phones or security system that could interfere with connection?

Error occurs when executing an item in an inbox with more than 1000 entries

Hi Everyone,
One of our approvers in SRM experienced an error when his inbox contained more than 1000 entries . Further execution on any inbox item produces errors.
Would you know where to set the maximum allowable entries in a user's inbox? Can this be set thru SRM config or Basis functionality?
We also searched for existing SAP Notes but found nothing.
Your inputs and help are greatly appreciated.
Thanks and Regards,
Vhong

Hello,
The user has sent me the screen shot. But this has no error messages. The approval transaction shows an ITS screen/code with template 'bbpapproval/99/saplbw02_1200.html'
However, we have a user in Quality where the page displays with no problem and with 1675 Entries.
Do you think this is more of an ITS setting or any Template/JavaScript issues?
I got this code (view source code) earlier today and the topmost header of the code is:

Regarding the not-so-good practice of approvers to have more than 1000 entries in their inbox, we are still in the process of planning on how to divide the task to different approvers since there is only one approver (Project Manager) for the related network.
Thanks and Redards,
Vhong

Problems when using outlook and outlook express, cannot send more than app 100 KB.

Since app 6 weeks ago we have problems when sending pictures etc, we cannot send more than app 100KB. If we send more there is error code
Socket Error 10053, Error number 0x800CCC0F. Your server has unexpectedly terminated the connection.
I have made no changes to either computer. Restoring the laptop to Nov 2011 made no difference.We use Outlook Exlorer and Outlook.
When I take my laptop to my neighbors house, who has Time Warner, I can send 10MB files without any problems, using the EXACT same settings.
Spending over 2 hours with a very informed Verizon technician on the phone did nothing.
I first blamed our server, turns out the culprit is Verizon.
Any ideas?
Eugene

Good Morning,
Are you able to send attachments on webmail.verizon.net?
Shamika_Vz
Verizon Support
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

HT201365 How do I change name of phone if I have more than one iPhone?

How to change iPhone name for find iPhone where I have more than one iPhone?

Settings > General > About > Name: Change the name.

High cpu when change "mls cef maximum-route ip" to more than 512K

Similar Messages

Maybe you are looking for