High low signals

Hello forum,
I'm relatively new to labview, however here is my situation. I have a motor driver that can be controlled externally with high (5v amplitude max) and low/ground signals. I'm lookng for a DAQ card with the ability to control 14 signals. Or if there is a better way of controlling I invite all suggestions.
DC

HI ASU,
Thanks for your interest in our products. For DAQ specific questions, I would highly recommend posting on the Multifunction DAQ board, found here. There you will have a much higher response rate to this type of question (hardware).
I would take a look around ni.com/daq for some great references on NI's different hardware options. You'll find many multifunction boards (analog, digital, etc.) that could suit your particular needs.
If you have more questions, feel free to start a thread on the DAQ boards.
PBear
NI RF

Similar Messages

ADAT into Logic Express, VERY low signals recorded

I tried Garageband, same problem, so now I am trying Logic Express.
When transferring tracks from an ADAT, through Alesis io/14, into Logic, the resulting sound files captured are VERY low signal. This should be a digitally ACCURATE TRANSFER. The Alesis montoring software on the mac senses the correct signal, the signal meters show correct levels (and sounds great), but Logic hears and records very low signals.
I note the Sound midi pref window only shows 6 channel 32 bit. It won't allow me to change to 8 channel 16 bit. Possible problem or am I chasing ghosts? I exhausted all my ideas.
Any thoughts?
T

Ropher wrote:
Discovering I was unable to import a ".au" file into Logic Express (or Garage Band) I read it into Sound Studio and exported it in a variety of formats. I can now successfully drag to Garage Band files in formats .aif .aifc .sd2 and .wav and get the expected result.
Unfortunately however, I only get the expected result importing these into Logic Express for the .aifc format which plays back at the expected speed with a low-pitched sound (but which doesn't display an uncompressed waveform). Importing the .aif .sd2 or .wav format files however results in the imported file being squeezed into a very short duration with a correspondingly undesirable very high pitch.
Is there some setting or magic incantation I need for reading in audio files to Logic Express without it getting squeezed?
Thanks!
--Roph
Yes. you need to ascend to level 5 before we give that secret incantation.
Really, you need to use a third party converter software, if you are going to use .au files.
Logic is happiest with .aiff, .wav files, but not much else.
Cheers

Texts Send Multiple Times if Low Signal

I just posted about a bug where a message disappears, but that reminded me of another longstanding bug I'd like to report.
Sometimes in an area of low signal [1 bar], the following happens when I send a text message:
Text is sent and moves up to conversation as grey message.
Grey message stays grey a very long time.
Message may turn black or may have "!" in yellow triangle and give error message.
About 75% of the time, the recipient actually receives the message even when it says otherwise. What's worse, it seems to be trying and trying to send the message, because usually the recipient receives multiple copies.
I have inadvertently done this where it was received 6 times [6 is high--usually it's 2 or 3 times] and still the message was reported as not sent. I get that it's harder to send a message in areas with low signal but this seems like a bug that needs to be addressed.

Text messages is one of my favorite features on my phone so I completely understand the need of it working as it should. Which model device do you have and what is your zip code? Is anyone else having issues with text messages?
Share details so that we can further assist.
Thank you,
LenaA_VZW
Follow us on Twitter @VZWSupport

Airport Express + Netgear = low signal??

Hi
i'm using an Airport express card in an Emac downstairs to receive a signal from a well-spec'd (and recommended) Netgear router which is upstairs and directly linked to a Mac G5.
No problem with the G5, but the problem is the signal strength is very low and it takes ages to log on for the downstairs Emac. Obviously distance is an issue but as the crow flies I suppose we talking about 15 m as the crow flies and one floor away with maybe two brick walls and wooden floor but no other (known!) significant barriers. This is a normal domestic house using normal building materials.
The spec indicates this should be no problem, so why the low signal?
Anyone else had problems with Netgear 'quip, or Airport Express? Both come highly recommended so I am somewhat surprised.
Any clues from anyone would be most gratefully received!
cheers

Brick walls do not allow high radio frequencies to pass easily. So, the brick walls may very well be the problem. Is there any way you can position the router so that the signals don't pass through the brick?

Slow WiFi transmission and low signal power (Airport Extreme extended by Airport Express)

I am experiencing slow wifi transmission between my notebooks and my base stations and I am hoping someone can help me fix it.
My wifi configuration is the following:
1 Airport Extreme base station (acting as router, wifi "creator" and DHCP server)
1 Airport Express base station (connected to Airport Extreme with a LAN cable, set up to extend wireless network)
1 Lenovo T410 notebook with Intel Centrino Ultimate N-6300 AGN WiFi antenna (I will call this one "Lenovo"), connected to wireless network, running Windows 7
1 MacBook Pro purchased in 2009 (I will call this one "Mac"), connected to wireless network, running Mac OS X Lion
1 QNAP T209-II NAS, connected to Airport Extreme via UTP cable
Airport Extreme (AXTRM) is creating a 802.11n wireless network with WPA2+PSK security with MAC address filtering. The other base station, Airport Express (AXPRS) is connected to AXTRM via a UTP cable. AXPRS is set to extend my wireless network.
My first problem is low signal power. My appartment is 90m2 in size and is in one floor. It is a new flat with high ceiling and modern layout, meaning little walls, big rooms and wide corridors. Still my notebooks, iPhones and iPad can barely reach AXTRM when I am on the other side of the flat. This was the reason why I purchased AXPRS and placed it in the middle of the appartment. My notebooks are placed just on the other side of the AXPRS's wall (less than 1 meter of distance and a simple 10cm brick wall in between), yet signal strength is only at about 80% (measured on my Lenovo using Lenovo Access Connections tool).
My first question is: Is it normal that in a 90m2 flat with not unusual obstacles, I need 2 base stations and even then have a rather poor reception?
My second problem is even more disturbing. I think I have catastrophic transfer speeds via wLAN. It takes over 1 hour to transfer cca. 1GB of files (average size 8MB) from my Lenovo or Mac to my QNAP. My Lenovo is showing about 250kb/s transfer rate when copying files. At the same time, Windows 7 show connection speed 144Mbps. This mean about 18MB/s. I know these numbers are theoretical and that actual transfer speeds are lower. But hey, 72 times lower? Furthermore, if I copy files from my Mac and my Lenovo at the same time, transfer speed is slightly lower. On the other hand, if I connect my notebooks to AXTRM via LAN cable and copy files to QNAP, transfer speeds are a few megabytes per second.
To make things even more confusing for me: if I transfer files from the internet, I get download speed at about 700kb/s, which is quite in line with my internet download speed. I don't understand why transfer speeds within my local network are so much lower.
Therefore, my second question is: How to set up my base stations and my routers to get a decent wifi connection?
I hope someone could help me. If you need any more information, just ask. Thanks!

From my experience of setting up the Airport WiFi for family members and friends, I have learnt the following :-
1. Airport Express is not as good as Airport Extreme, for being as extender, the difference can be quite a lot.
2. There is always a dead cornor (bad reception) in a house
3. Even moving the Airport Extreme / AE a few inches, the performance can be improved quite significant
4. If possible, always choose 5G 802.11n than 2.4G, unless there are many thick walls.
My suggestion will be as follows :
1. Moving out the AEBS out of a closet, is a good idea
2. Always try to locate the AEBS in the centre of a area, instead of the two sides
3. Try to test the AEBS without an extender, and find the best location area (don't place on the floor, neither above 6 feet height)
4. After finding a best location, set the extender closer to the AEBS, and then moving apart from it (check the performance after every move), it is better that both devices can face each other.
5. I can't tell you the reason, and some people may not agree with me, the new 2013 Airport Exteme performance is better and may be is a good idea to replace your Airport Express, and use it to connect with your router, and old AEBS as an extender
6. Some Powerlinks (in case you can't use a wired ethernet connection between the two devices) work and some don't work with Apple Airport products, therefore, if possible, have an option to return them to the shop if they do not match
Good luck

Yoga 3 pro - WIFI low signal

On a brand new Yoga 3 PRO 1370 -
I am getting very low WIFI signal on all my routers.
Compared side by side : Think pad yoga and yoga 3 pro - the first one have full bars on signal , the 3 pro have only 1-2 bars and disconnect all the time.
Only when the laptop is very close to the router - getting full signal bars.
Already removed and update the drivers twice . tried all configurations and power options - still very very low signal reception.
Any ides ?

XBrav,
Way to go, yes I do agree with XBrav wilkster. If you can check the screen shot that XBrav provided.
If your software and drivers doesn't match up you can check this link to download the most up to date software and drivers for your Broadcom 802.11ac Network Adapter.
Please let us know if this can help.
@ XBrav thanks again
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

LENOVO S860 Poor Performance in Low Signal Locations

Just bought two of this phone (2 GB RAM international model) for myself and a colleague.
I'm really pleased with the build. However, I have to say it doesn't perform well in low signal locations and this is quite worrisome as I work in a low signal location so miss most of my daily calls. Such a brilliant phone can't be flawed by the most basic and important function.
LENOVO please release an update to fix this low signal problem asap. Thanks.

Am facing this issue from last four months, Lenovo is not interested in solving this problem. My suggestion is replace this with some other brand. Even Redmi 1s (INR 6000) has better signal compared to Lenovo s860.

WMP600N - weak connection and low signal - Windows 7 x64

I bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64.
My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I'am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), please release a proper driver for the WMP600N!
Message Edited by Storm_dutch on 12-20-2009 09:51 AM
Message Edited by Storm_dutch on 12-20-2009 09:52 AM

I'm not sure about you guys, but I use WMP600N and running Windows 7 64bit without any issues. The driver that I'm using now is Driver Version: 3.0.2.0, Driver Provider: Ralink Techonolgy Corp, Driver Date: 6/19/2009. Here's what I did when I upgrded my wireless adapter. 1. Uninstall the original wireless driver from device manager. 2. Turn off the computer and phisically removed the wireless adapter from my computer. 3. Pop in the new WMP600N and turn on the computer. 4. Windows 7 then automatically detects the new adapter and intall the proper driver for it. Well, that's all I did. The whole process is very simple and straight forward.

Down payment amount cannot be higher/lower than the preset value Error

Hello. Can anyone help me with this error. When creating a down payment request from a sales order with a billing plan, I get the message 'Down payment amount cannot be higher/lower than the preset value' and the document isn't released to accounting. When creating the sales order, I included a condition type that I created. The billing plan then calculates the down payment request value with the total sum i.e net value plus condition value. Upon creating the down payment request in VF01, I get this message. I did a test and noticed that, if the condition is not included in the sales order, the down payment request is created without errors. How do I correct this? Thanks for you anticipated response.

Hi
As you are getting error, 'Down payment amount cannot be higher/lower than the preset value' ,please check the total value of the document.So in the sales document ,billing plan check what is the invoice value for the first billing date , also check what is the sales order value.Secondly what is the condition type that has been created and for what purpose it is being used.
Regards
Srinath

New Nokia Asha 306 No Network or Low Signal Proble...

New Nokia Asha 306 No Network or Low Signal Problem (pricing date may 31 ,2013)
i have nokia asha 306 have signal problem when i make use sim some time show signal only two signal and show proply opreater any solution thnks in advance

May i ask how old is your sim card? This may be a sim card you should try exchange it its over a year old and revert back ,keep in touch.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

K8D Master-F High/Low beep tones

Hello,
Running the system even on bare minimum (PSU, memory and CPUs only) the board will not post and will only return a constant high then low tone beep code. Information from AMIBIOS suggests faulty CPUs, but this is doubtful that both CPUs would be damaged (I've tried one at a time, and in different sockets), as their serial numbers are quite a distance apart.
Anything else I can try? or do I have a dead board?
Thanks in advance,
LJP

Quote
Originally posted by Wonkanoby
it would help if you listed full hardware specs
and psu details
the 4 pin 12v feed is connected?
the ram is registered ddr ?
Full specs:
MSI K8D Master-F motherboard
2x Opteron 240 CPUs
4xGiel 512mb Dual channel ddr 3200 ram (even with all removed it gives the high low beep tones)
This board uses a SSI compliant PSU, its 24 pin main power, 8 pin additional power. 550W supply thats in it.
*Mass of edits*
Couldn't tell you if its registered DDR, ram isnt the problem though, it would give a ram error beep code running with no ram onboard, yet it still has the high/low beeptones.

Expressions and Defining High/Low Limits

I have an accuracy requirement to assign a 1.5% and a 1% High/Low from a previous test. The previous test is a Numeric Array where the first 12 values have to be assigned a 1.5% limit and the remaining 4 have a 1% limit.
Is there a way to do two while loops on the same step or do I have to break out each element in the array and define its own Parameter.
So basically I have something like this so far:
First test with post expression:
Parameters.Test = Step.NumericArray
Then I have an expression step with the loop options going 1-16 with this...
RunState.NextStep.Result.Measurement[ RunState.LoopIndex ].Limits.Low = (Parameters.Test[ RunState.LoopIndex ] * 0.985),
RunState.NextStep.Result.Measurement[ RunState.LoopIndex ].Limits.High = (Parameter.Test RunState.LoopIndex ] * 1.015)
But as you see that will add a 1.5% to all of them...Do I have to break out each element in the array individually?? Or is there a way to modify that expression to make the last 4 values of my array multiply by .99 and 1.01?
Thanks
Message Edited by Roons1159 on 02-20-2007 03:22 PM

I got it.. I didn't know I could define paramters for any given step in a sequence, only thought Step, previous step, and next step...

12inch PB, real low signal. How to install 10.4.1 kext files?

Noticed a problem when my girlfriend new Dell can pickup about 11 access points- all with kinda low signal but my Powerbook does not see ANY of them, once in a while it might pick one up for a second, but then it is gone.
I know this is a documented issue with low signal. I downloaded the 10.4.1 drivers (kext files) to install thinking this might solve the issue as it has for several others. Wondering how to install these files though, there are two AppleAirPort.kext and AppleAirPort2.kext. I also want to know what files to backup should there be an issue, or I want to go back? Any help would be awesome!

It says above 2 relevant and 1 correct answere available .............
I'm new here so could anyone direct me to these answeres?

How to display and print CCR showing not only results, high, low or normal, but also normal ranges of tests.

How do I display and print CCR showing not only my actual results, high, low or normal results, but also normal ranges of each test? I can do this individually but not for the composite CCR.
Thanks.

Hi,
I'm not exactly clear on what you are doing. I can tell you that the ranges and flags for high, low, and normal come from the lab results provider in the lab results they sent you, not from HealthVault. If you go back to the original document that came from
the laboratory, you should be able to open it as a document and print it.
I hope this helps. If not, please respond with more details, or if you'd prefer a private conversation, please contact HealthVault customer support by opening a support ticket with them.
Thanks,
Kathy

Live A/V Broadcast How to support both High & Low bandwidth users ?

Hello there
I have been working on a requirement where I need to
broadcast live audio and video feeds
to Flash Media Server from where it gets broadcasted to our
customers. We have two types of
customers: High bandwidth and Low bandwidth.
Now could anyone please tell me what kind of scripting is
required at the server end so that
the Media server broadcasts to these two level of user groups
at same time. How do we control
the live feeds received at the Media server ? How do I
control the amount of bandwidth that at server
side based on the received feed so that I can broadcast to my
users based on their capacity ?
I tried running two separate flash application pulling the
feeds from SAME camera but that didn't
work as changing the settings (like Camera.setMode..) on one
program affects the settings on other
program(as both programs are connected to same camera/mic). I
do not want to buy two separate
cameras/mic to support both high/low bandwidth users. I would
need to do it programatically.
Could anyone please let me know your thoughts, it would be
very helpful to me and others.
Many thanks,
-Sakthik

Thanks Charles for your reply. I didn't know that FMS doesn't
support this feature. So you mean to say that there aren't any
other ways to control live feeds at server side ?
I would try your suggestion on setting the bandwidth and FPS
at client side but I am not sure how effective will it be because
the Server is going to push a high bandwidh data to a 56 Kbps
pipeline. There will be lot of data loss due to this narrow
pipeline. Do you think that applying setBandwidth and setFPS on
this narrowed data is going to be effective ? I dont think so, what
do you say ?
How exactly does this setBandwidth and setFPS works ? When
will it modify the data ? Will it modify the data after or before
receiving it at the client end ?
Please share your thoughts on this.
Many thanks,
-Sakthik

High low signals

Similar Messages

Maybe you are looking for