High pitched whine from netbook when power is plugged in. Does not charge when computer is on.

I have a specific power / charging issue On HP Mini Netbook 210-1077CA. Windows 7 starter ( I think)
With the computer OFF ...
When I plug in the power it gives a high pitched whine. Red battery light is on, showing it is charging. (computer is off.)
To test the computer I have turned in on after charging for a little while and the % of charge is increasing. Showing that it is charging properly.
HOWEVER,
With the computer ON
The battery light turns white and does not stay on, but flashes periodically. Its not a constant flash but a pause of several seconds between a series of flashes.  The manual indicates a Flashing Battery light seems to indicate either going into a sleep mode because there is not enough battery power (however my power is at 14% normally this happens I think at 10%) OR as the manual indicates there is a problem with the battery.
I removed battery, removed power plug and then pushed power button holding for 15 seconds.  No change in behaviour.
I also tried to boot the computer with just the power plug in and no battery. But it would not turn on. I don't know if that is normal or not?? Interestingly the White battery light, while trying to turn the computer on without the battery stayed white no flash.  (but did not turn on either as I mentioned.)
I read a few posts that say that the whining are Capacitors doing some sort of harmonics. Although I have never heard this sound before.
Im sure that this problem is not fans or heat sinks etc. Since in only happens when the computer is off  and charging. In my opinion its definitely electrical. The sound seems to be coming from the center of the netbook or the battery area..
So my conclusion is ...
1. Battery has problem and needs to be replace,
2. Maybe the AC adapter is bad, since it doesnt boot w/out battery (if it is suppose to ??)  Also since it seems when I turn it on it goes from Red charging to white flashing as soon as it starts to boot. Could it be the AC adapter is not giving out enough power to charge and to boot at the same time.
Anyway can anyone help me on this issue. Im not sure whether to start by getting a new AC adapter or new battery. I would not like to buy new both and just throw money at it.
Maybe it is not either???
You help would be appreciated.
Regards. 

I have resolved the problem.
I replaced the AC adapter. Everying works find now. I tested runing the computer without the battery, and it works. So I might add that a possible test for an adapter that is not functioning properly is to try running it w/out the battery. If it does not run its possible that the ac adapter does not work.
Thanks.

Similar Messages

  • My new ipod 6th generation doesn't appear on itunes and does not charge when connecting to iMac...Any suggestions?

    My new ipod 6th generation doesn't appear on itunes and does not charge when connecting to iMac...Any suggestions

    If you have a PPC iMac, see KB Article:  http://docs.info.apple.com/article.html?artnum=301733 iMac G5: How to Reset the SMU (iMac G5, the iMac G5 (Ambient Light Sensor), and the iMac G5 (iSight)).
    Intel iMac, see KB Article:  http://support.apple.com/kb/HT3964 Intel-based Macs: Resetting the System Management Controller (SMC)
    Your iPod is "new"  & still under warranty.
    Every iPod comes with complimentary, single-incident telephone technical support within 90 days of your iPod purchase.  If you also purchased AppleCare, then your warranty is extended for technical support and hardware coverage for two years from the original purchase date of your iPod.
    Or, take your iPod Nano to your local Apple Store or AASP.

  • MBA battery does not charge when connected. Help!

    My MBA battery does not charge when connected to the charger. Ive checked the other threads and followed advice but nothing seems to help.. My battery health info is good, I've tried cleaning the magnetic pins of the charger, reset smc but it still does not charge. The light on the charger is green or does not come on sometimes, and it's the same for a few Power outlets. What else can I do? Would greatly appreciate any help! Thanks.

    It recognizes the charger intermittently. After cleaning, it showed the charger as connected but not charging the battery. I will try my friends charger later to see if it works. Thanks for your help!

  • Battery does not charge when asleep

    Ever since I upgraded to Tiger my PowerBook battery does not charge when it is asleep and the display is closed. It only charges when the computer is active and display is up. Anyone else experiencing this? Solutions/work arounds??

    Hi, Donald. Try resetting your Power Manager, and you might also trash the preference file com.apple.PowerManagement.plist. If you trash the pref file, be sure to restart and reset your preferred Energy Saver settings afterward.

  • HT4972 hi. my iphone 3gs was stuck on apple logo, does not charging. when i replace the battery, it works, my promblem not is, in can't or won't read the simcard. i cant activate my phone. even i put att simcard. how can i activate it? please help me. tha

    hi. my iphone 3gs was stuck on apple logo, does not charging. when i replace the battery, it works, my promblem not is, in can't or won't read the simcard. i cant activate my phone. even i put att simcard. how can i activate it? please help me. thanks.

    Apple recommends backing up the data when you're getting the battery replaced by them. So I assume that you will likely lose the data during this process.
    Will the data on my iPhone be preserved?
    No, during the service process all data on your iPhone will be erased. Before obtaining service, it is important to back up your data using iCloud or iTunes. Apple is not responsible for the loss of information while servicing your iPhone and does not offer any data transfer service. During service, Apple may exchange your iPhone with an iPhone that is new or equivalent to new in performance and reliability.
    Following service, your iPhone may have a newer operating system (iOS) version and you will need torestore your data using the method used to back it up (iCloud or iTunes). As a result, you may also need to update your App Store applications to ensure compatibility with the newer iOS. If you experience a problem with an application purchased from the App Store, check to see if an update is available or contact the application vendor directly.
    copied from Apple - Support - Service Answer Center

  • Battery does not charge when plugged in

    Battery of my i phone 5 does not charge when plugged in!

    Hi
    Try this:
    Disconnect AC
    Shutdown
    Remove battery
    Connect AC
    Startup
    Open Device Manager
    Click the plus (+) sign next to Batteries category, right-click All of the "Microsoft ACPI Compliant Control Method Battery" listings, and select Uninstall In the "Confirm Device Uninstall" dialog box, click OK. (it’s ok if you only have 1 of these listings).
    Click the plus (+) sign next to System Devices.
    Right-click the “ACPI Fixed Features Button" and select Uninstall. In the "Confirm Device Uninstall" dialog box, click OK.
    Shutdown
    Disconnect AC
    Insert battery
    Connect AC
    Startup
    Also request you to try updating the Bios once on your unit.
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • High pitch whine and FireWire bus power

    Delighted with my MBP!
    Just noticed the high pitch whine today when I set it up in a quieter room and plugged it into an IOGear bus-powered FireWire hub shared with my other Mac.
    It was around 8000 hz and loud enough that I could not stand to stay in the room with it.
    When I unplugged it from the hub and connected the cable directly to the FW port, the whine was greatly attenuated (I could hear it only by putting my ear next to the vents at the top of the keyboard).
    Could the problem be related to powering the FireWire bus? (It reminds me of the sound of a switching power supply or DC-DC converter) Has anyone else had any success in finding ways to attenuate this high pitch tone?
    MacBookPro   Mac OS X (10.4.5)   7200 rpm

    Hi, Thanks for the suggestion. I'm really trying to cut down on the number of devices that I leave plugged into the mains, so would ideally like a solution that relies purely on power supplied by the internal bus.
    I've had a bit of progress with my current set-up. I've switched to using a 2 headed USB lead that came with my Hard Drive. This does mean I effectively lose a USB socket, but it appears that the Hard Drive + the Webcam can now live happily together.
    It just means that I have to swap the 4th USB port for whatever ad-hoc device I need to use at the time rather than leaving things connected to it.
    Out of geeky curiosity, I'd still be interested to know whether the USB and Firewire buses share their power or each have a dedicated amount.
    Cheers,
    Ian

  • A high-pitch whine from a KM2M?

    OK, this is REALLY upsetting me and I figure someone out there might be able to help.
    I bought a KM2M combo motherboard from a local computer shop about 3 months ago. I was using an AMD XP 1900+ w/ 192 megs of pc-133 memory.
    Well, I upgraded a few things and here's my current list in my rig:
    KM2M Combo mobo
    AMD Athlon XP 1900+
    Cables Unlimited Super Quiet "whisper" cooler w/ copper core (it dropped my cpu down from 104F to 84F!!!)
    8x AGP PNY Nvidia GeForce 5200 Ultra w 128 megs ddr memory
    512 megs(2x 256) Paired ULTRA DDR pc2700 dual-channel memory
    92.6 Gigabyte Hitachi Deskstar ATA-133 hard drive with hard drive cooler attached
    8x Lite-On DVD-+R/W drive
    2 80mm high-flow Speeze brand case fans
    300 watt ULTRA Power Supply w 2 blue LED 80mm cooling fans
    Scorpion see-through yellow IDE & Floppy cables
    Well, after a few changes, my mobo starts to make this REALLY high-pitched whine! Well I thought it might be the PSU or heatsink, so I go through EVERYTHING and NOTHING is making this sound! I even tried changing memory & power settings in the BIOS, but no luck.
    Well I set up this exact setup on a chaintech mobo and I get NO shrill sound whatsoever! (proof it isn't something outside of the mobo)
    Any ideas on how I can fix this? I would take it back to the computer store & get it replaced but my dog chewed up the box it came in a few weeks back so I can't take it in to get it switched out...  

    That is a fine set of stuff you have. The PSU also has a fine name, but what ampères does it give on 3.3, 5 and 12 volt? Try to localize the sound, for example by holding your hand to a device - not a fan! - and see if it is a bit loose, cause it sounds like something is loose, the Northbridge heatsink or a capcitatior, as you say.
    Elsewhy, follow the thrilling development in the thread suggested by Osnavi.

  • My IPad Retnia does not charge when plugged in using the USB from my computer to car adapter, how can I fix this to be able to have flexibility in charging?

    When I plug me IPad into the USB connector to my laptop or into my car charger, it show as not charging. How can I fix this so that I can charge my Pad in these settings?

    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    And this - Unplug the charger from the iPad and then replug. May resume charging.
    Or - Recalibrate the battery. See link below.
    The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Best Practices for iPad Battery Charging
    http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    How to Save and Prolong the battery life of your new ipad
    https://discussions.apple.com/thread/4480944?tstart=0
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    To Extend a Device’s Battery Life, Get to Know It Better
    http://tinyurl.com/b67c7xz
    iPad Battery Replacement
    http://www.apple.com/batteries/replacements.html
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • U310 does not charge when on

    Hello,
    I've recently purchased a refurbished Lenovo u310 from a UK seller. The ultrabook will only charge when off. If I turn it on, it will say that it is plugged in and not charging. I have tried this in both Windows and Linux and have also played around with the Battery Management software with no luck.
    I have also tried contacting the UK call centre and they were really no help before being cut off after the call costing me all of my credit on my phone.
    Is there any other way I contact Lenovo online? Is there an easy fix?

    Hello,
    I tried both methods A and B before posting this thread several times. I had no progress with method A as the battery guage test requires the laptop to be connected via A/C power and the laptop does not acknowledge that it is plugged in, even though I had it plugged in the whole time.
    I have not tried method C as I was a bit unsure as to whether or not I should take the laptop apart to disconnect the battery as the U310 has an internal battery.
    I hope this helps, I would really like to get some resolution on this problem. Is there any way I can send it off to get it repaired considering it is still in warranty and that it was a refurbish model?

  • HT4236 I want to delete photos from my iPad but this help page does not help, when I click on devises a pop up for photos does not appear.

    I want to delete photos from my iPad . But the help page does not help. When I click devices a photo pop up option does not appear

    The instructions in HT4236 are as follows:
    To delete synced photos and videos
    In iTunes, select the device icon in the Devices list on the left. Click the Photos tab in the resulting window.
    Choose "Sync photos from."
    On a Mac, choose iPhoto or Aperture from the pop-up menu.
    On a Windows PC, choose Photoshop Album or Photoshop Elements from the pop-up menu.
    Choose "Selected albums" and deselect the albums or collections you want to delete.
    Click Apply.
    No where does it say anything about a "photo pop up option". When you click on your device icon a panel with many tabs appears. One of these tabs is "Photos". You are supposed to click on the "Photos" tab.

  • My HP Envy 15-j051 does not charge when computer is on but does charge when powered off

    whenever I am on and plugged in if get plugges in but not charging yet when I shut down and keep power supply plugged in it charges the battery. I have checkd the battery and it said primary-OK (1) dis systems check all passed
    This question was solved.
    View Solution.

    @lagrit1023 ,
    Hello and thank you for posting on the HP support forums.  What you may have happening here is a problem with the power regulation on the motherboard or an issue with not enough amps  from the power supply.
    Can you try the power supply on another notebook or have someplace you can take it to be checked?
    The only other way to check this if you have already done the battery checks and so on is to get the system sent in for repair.  For this you will have to contact HP phone support.
    Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    Please let me know how things go.
    Thank you again for posting and have a great day.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • MacBook Pro will not charge when Computer is on. Can only charge when shut down, MacBook Pro will not charge when Computer is on. Can only charge when shut down

    Hi can anyone help me? My MacBook Pro cannot charge at all (keeps showing not charging or not connected) when i am using it. only when i shut it down or let it sleep then wil it begin to charge normally. Does anyone know what to do??

    You could always try a SMC reset -> http://support.apple.com/kb/HT3964 - but I don't believe that will solve your problem.
    If I were you, I would take the machine to your local Apple Store or an AASP and have them diagnose the problem. It could be something very simple or it may be something more complex within the power management system.
    Good luck,
    Clinton

  • Battery does not charge when my Satelite Pro L500 is off

    Hi.
    I have a Satelite Pro L500. Normally when it is plugged in the DC in and Battery led lights are lit up. Now both are off when it is plugged in and the computer is off. I have found that in this state the battery is not charged. The computer will not switch on while the power is plugged in. If I remove the power source and wait a few mins the computer will now switch on and opperate normally.
    If I now plug in the power the leds are lit and the battery is charged

    Hm. You mean the notebook does not boot up when AC adaptor is connected but it powers up if the AC adaptor is not connected?
    Looks like an hardware issue maybe power supply electronic problem
    Of course the AC adaptor should be checked too
    L500 is not a very old notebook series and I think the warranty should still be valid
    In such case everything should be covered by warranty so dont loose the time and get in contact with an ASP technician

  • Macbook Pro-battery does not charge when on standby

    Funny thing, I discharged my battery recently and when I plugged my power adaptor I put the computer to hibernation. When I opened the screen the charge was still 15%, same as b4 hibernating. The computer would not charge the battery whenever I close the screen and the problem remains. Anyone had similar problems?

    This isn't a normal behavior. Have you verify if the magsafe adaptor was properly connected, i.e. that the amber-LED was on?

Maybe you are looking for

  • Connect PostgreSql in ABAP Program

    Hi All, I have a requirement, there is an external software with postgresql DB. I want to fetch some data from this postgre DB to in ABAP program. How can i connect this DB in my ABAP program. Please help . Regards Jitendra Singh

  • Mail 7.3 quirk

    MBP mid 2012, OSX 10.9.4, Mail 7.3 When I delete an email from my inbox Mail selects the next message and removes the unread icon prior to me opening the message. Is there a way not have this happen? I often find that as I  go back through my emails

  • Album cover flow

    Hi all, This is probably nothing technical at all but it's something that really bugs me! The album artwork on the cover shows the same album two to three times, is this strange and is there anything i can do to get rid of it. it really annoys me!!!

  • Page Properties and Text Rollovers

    I have been trying to create simple text rollovers for my page and have ran into a confusing problem. In Page Properties, I used the link feature to make a word in green text turn orange when the mouse rolls over it. This works fine. However, what if

  • I need to know how to set up my itunes card i bought at the store on my phone please

    I need to know how to set up my itunes card that I bought from the store to my account on my phone