Hlp. on Overclocking AMD Barton 2500+

BlueI need help on this overclocking matter.I just got this New AMD Athlon(tm) XP 2500+ Barton run on Ms-6734(KM4ML) MSI mainboard.
I 've read a lot about overclocking Aticle and found out the only way to clock is to go for this so call 'Multiplier'.but when I go thru my Bios setup there was no mutiplier?But the board say it support overclocking?
I did download CPU-z software.And it say my CPU speed are 1.83 Mhz.Pls.hlp me on this,I really need to know how to overclock this CPU a little far from 1.83Mhz?

Quote
Originally posted by scooter787b
to aseaver: it is possible to unlock a 2500
to Alex66: i do not know much about your board, but try looking to the manual for some advice on the jumpers, and many boards today can go over the fsb limit, many p4 board have gone way over their 400fsb "limit", its just that chip companies dont use speeds that are "odd", so motherboard companies can make a mobo that works with a variety of chips, try to find out what those jumpers do or look around in bios, to see if u can change it "manual" or somethin
I did go into the Bios setup go thru the Frequency/Voltage Control this is what the manual say if I need to do some Overclocking.There only two option in Frequancy seting: Auto Detact DIMM/PCI CLK (Enable/Disable)
           Spread Specrum                (Disable/+/-025%,0.35%,0.50% and0.75%
If I need to overclock I have to Disable the Specrum?One thing I did too is I go for the jumpers too but the seting are still the same,the thing is that there no Multiplier could be seem in the Cmos?I dont know wat else can I do to overclock this board.Might be this board is non overclocke type but why does it say this board designed to support overclocking?Ahhhh.....wat a life I've got this board for...I really need help on?There must be a way.....:(
My Board are: MS-6734(v1.X)M.ATX mainboard.
Support Socket A(socket-462)for AMD Ahtlon/Athlon XP/Duron
Chipset Via KM400
Support 200/266/333FBS
support DDR200/266/333

Similar Messages

  • KT4 Ultra-SR (MS-6590) dont work with AMD Barton 2500+

     ;( Please help me any1.
    I have MBO KT4 Ultra-SR (MS-6590) with CPU AMD Barton 2500+ and i have a big problem. System corectly boot only if a select CPU FSB Clock = 100 MHz (CPU Ration/CPU Vcore/DDR Voltage=all AUTO). When a select CPU FSB Clock 133 or 166 MHz, system begin run corectly and after few second turned OFF. I selecting SDRAM Frequency on=AUTO/266/333/400 MHz but not working. My old CPU is AMD XP Palomino 2100 MHz and work fine with KT4 Ultra MBO. I upgrade BIOS with 1.4 version. I change memory module with PQI (PC 2700/256 MB) and JETRAM (PC 2700/256 MB) but is same ":censored: ". System dont work. Bad CPU Barton 2500+? I dont no. Please help me any1.
    My System:
    MBO KT4 Ultra-SR (MS-6590)
    CPU AMD Barton 2500+ (FSB 333)
    Memory DDR Samsung 2x256 MB (PC 3200) K4H56083D-TCC4
    Cooler SPIRE WhisperRock IV+Artic Silver 3
    HDD Seagate Baracuda 120 GB SATA
    PSU Enermax 300W EG301P-VE(FMA)
    VGA Saphire ATI Radeon 9100 (64 MB+TV/DVI-out)
    DVD-ROM Pioneer 120S (16x speed)
    CD-RW MSI CR52-A2 (52/24/52, Atapi)
    FDD Teac 1.44 MB
    Creative SoundBlaster Live! 5.1

    Most of the time, this sort of problems arise because of power suppliy issues.. U have a enamax 300W PSU which is a VERY GOOD PSU but might just be on the line...
    If u can, try swapping the PSu for a good 400 or a 420W PSU.. this might solve your enigma.. I really dont think this is your processor...
    Read this two articles on PSu wrtten by one moderater which will aid in solve in fixing your problem (PSU1 , PSU2 , Troubleshooting Guide )
    Best of luck
    RAsika

  • MSI 6712 (KT4V) Problem AMD Ath Barton 2500+

    Hi guys , im wondering if u can help me
    ive got a AMD Barton 2500+ running @ 1498 instead of 18XX , ive tried the following,
    Setting Vcore standard to 1.65
    FSB 166 , System does not boot
    FSB 133 , System thinks its a AMD 1900+
    FSB 150 , System does not boot
    FSB 100 , System thinks its AMD 1100
    so now im running 1498mhz instead of 18XX mhz  
    every time i have to reset the bios to make it boot again ,
    My memory = Whitelike 333 DDR 2x 256mb Pc 2700 (single sided)
    My GFX = Chaintech Gf4 64mb AGP 4X
    Running XP sp1a Professional
    Any ideas setting it to 18XX ??
    ive tried all the ratios 11 , 10 , 4 , 12.5 , 11.5 , 13.0 14 , 15 nothing seems to work
    even setted the memory to 200mhz , that didn't work ...
    Any ideas?

    Well Mate - If the temperature in safe mode at the lower CPU Speed is that high then it means at the proper speed the temperature would be high enough to prevent the system from booting.
    And according to what you wrote about the white paste I suspect that your installation of the heatsink is the cause of the problem - which brings us back to the point - have you tried re-installing the heatsink with a thermal pad - not the silicon paste as per AMD instructions?
    Anf if after following AMD's installation instructions to the letter you still have the problem you may have a faulty CPU - but unfortunately you will find that you have voided your warranty if you have used any paste instead / as well as the original Thermal pad.

  • Powers off above FSB of 133 (barton 2500)

    Ok here we go....
    K7N2 Delta ILSR
    AMD (Barton) 2500
    Mushkin 512MB 3200 In the Light green slot
    Enhance 300W PSU
    Fresh Install of XP Pro SP1
    Copper cooler CPU Fan and heat sink
    120MM Case fan
    Big Ass Problem
    First of all when I was installing XP from CD it would get to the starting windows screen and then just power off. The only way to start back up was to unplug the power supply and it would power back up.
    I changed to the Bios to defaults and was able to get XP loaded. (Only running at 1100 on the processor)
    Now when I change the FSB to 166 it will run for about 5 to 30 min and the power of issue is back. I change the FSB to 100 or 133 and it will stay on and I can even use it.
    Could this be a memory issue or a heat issue? It has even powered of in the BIOS screen when I had the FSB on 166.
    Any ideas?

    Afternoon
    Depends what else you've got on your system. My system runs fine with a generic 350W PSU - people will tell you that you need 500w beasts, but hey - Kingmax Memory is supposed to be stroppy with Deltas, but mine's fine The only thing I'd say is that if you've got more than 1 HDD and 1 CD/DVD, then you could do with pepping up the PSU.
    Mine's been running non-stop since I got it, night and day, never hit more than 35C with stock cooling and no case fan, and never locked up. Yippee

  • If you have a gf4 ti, amd barton 2600+ and unreal torunament 2003 please read!

    i have a ti4800se, and athlon 1.2, in benchmark: dm-inferno with 1024*768 16bit
    I get this results
    UT2003 Build UT2003_Build_[2002-09-19_17.26]
    Windows XP 5.1 (Build: 2600)
    AuthenticAMD PentiumPro-class processor @ 1204 MHz with 255MB RAM
    NVIDIA GeForce4 Ti 4800se with AGP8X  (5216)
    dm-inferno?spectatoronly=true?numbots=12 -benchmark -seconds=77 -exec=..\Benchmark\Stuff\botmatchexec.txt
    2.110242 / 31.547962 / 144.437958 fps         rand[28925]
    Score = 31.546055
    could you post yours?? thks

    ive got an FX 5600 (256mb) which isnt working right , AMD Barton 2500+, and 512mb ram that scored this
    6.047448 / 65.683128 / 251.481369 fps -- Score = 65.687851        rand[22298]

  • With which msi mobo can i overclock my amd barton ?

    Hi,
    I want to run my AMD AthlonXP Barton 2500+ at fsb 200 !
    Which MSI mobo can I use ?
    Greetzzzz,
    LunnyFish
    http://www.chivas.be

    In this forum you can find a page for overclockers. Shure you can find more help there.

  • Overclock Barton 2500 with PC2700 memory

    Using MSI K7N2 Delta L MB.
    Want to overclock Barton 2500 [without and CPU mod].  But, memory is not overclockable.
    Is there a way to overclock the CPU while keeping the memory running at 166/333?
    When I've tried to raise the FSB of the CPU, I can't get the memory clock to stay at 166/333.
    Thanks

    dont run a fsb higher then the memory as its most likely to be slower.
    you can try to increase the speed 3-4mhz at a time until it starts to crash and then you back off 5mhz.
    or buy faster memory.
    you can always raise multiplier.
    im not sure but i think the highest you can go is 12.5 and if you chose higher it goes back to lower numbers.

  • Barton 2500+ K7N2G-L How to overclock?

    Hi
    Im completely new to overclocking and I dont understand the jargon here and at overclockers.com.
    Could anyone explain in simple words how I could speed up the system?
    Ive heard there are some windows programs which do it, could this be that simple?

    It would be best not to overclock untill you understand every thing about it and the terms.  
    1st if your running stock cooling i would not even try
    2nd If you have the newer barton 2500+ then the CPU is locked and the wire trick does not even work, But older models are unlocked with the motherboard you bought.  esay way to tell if you change the settings im going to mention its unlocked.
    Over clock in the bios chage the FSB up in small increasements it should be default at 166 (333 CPU bus speed) and you can also change the multiplier it kind of works like this.
    166FSB X 11multiplier = 1830MHz roughly (your CPU)
    If you change something like this:
    180FSB X 12multiplier = 2160MHz
    but if you cant change these settings then your CPU is locked and you cant overclock unless you want to go some major altering your CPU.

  • Overclock AMD Athlon II X2 250 on MSI 760GM-P21 (FX)

    I want to overclock AMD Athlon II X2 250 on motherboard MSI 760GM-P21 (FX), integrated video card from motherboard and MS-TECH VERTIGO 520W 80+ power supply.
    But before buy this power supply I had a NoName 400w.
    And when I oc on NoName PSU after 3,3 ghz I receive BSOD.
    How to oc more than 3,3 ?
    Ty.

     The CPU itself would work just fine up till the current draw exceeds the limit of CPU VRM (Voltage Regulator Module) and fry it. Even tho it's listed as supported don't use CPU over 95W and even then under heavy loads for longer periods of time a 95W CPU could possibly cause damage also. If using a 95W don't OC it any. The VRM on the 760GM was never intended for 125W CPU.
     The only reason the 125W CPU is listed is because competing brands show support for them and MSI made the wrong decision to list them also just for competitive marketing purposes.

  • Msi Kt333 woes with barton 2500

    Hi,
    I just got this new processor, the barton 2500 and my computer is very instable.
    I have a Kt333 ultra 2 with bios 5.7 and it worked fine with an athlon xp1800+
    I set up fsb 166 and everything else in auto and It will crash at random in winxp.
    The culprit seems to be accessing the hard disk which is a Maxtor ATA133 7200rpm 60gb.
    In one of the BSOD the file that caused the crash was ntfs.sys
    I am now running the board at fsb 133 just so I can use the computer.
    I have currently installed 1G ram, two sticks of 256m pc2700 and a newly acquired stick of 512 pc3300.
    I have a Gf3 ti 200 128m at default settings.
    What can I do to fix this without having to go out buy more hardware?
    Thanks.

    I don't think the KT333 suports ddr400(3200), the Bios 5.7 you have was to fix the 3200+ barton NOT the 3200 ram, So you can only run the DDR333 (2700) ram
     and should never mix your ram it will cause nothen but trouble

  • What have you got out of the barton 2500?

    Lets find out what the barton 2500 can do.
    So far i've got 2326 out of it
    But what have you done?
    Please join in and show what you have done.

    You can see my numbers in my sig too.  
    Take Care,
    Richard

  • MOVED: [Athlon64] Overclocking AMD Athlon64 on MSI RS480M2-IL

    This topic has been moved to Overclockers & Modding Corner.
    [Athlon64] Overclocking AMD Athlon64 on MSI RS480M2-IL

    Quote from: xlinkch on 06-July-05, 00:46:15
    Vdorta: Can give more instruction how to run the ClockGen program??? Do I have to load it every time my Windows bootup???
    I don’t have my computer at hand, so the following is from memory, aided by the ClockGen site:
    1. Download the RS480-specific zip file to a folder and extract its contents.
    2. Run the CG-ICS951412.exe file; click on the “Get” button to obtain the current FSB value; adjust the new FSB value you want (there are five values: 200, 204, 210, 214, 220). I tried and tested them all and they were stable in my machine, so I chose the highest, 220.
    3. Create and save in the same folder a simple text file, for example, “filesave.txt” with a text editor (I used Notepad) with the following two lines in it:
    [CG-ICS951412]
    FSB=204
    (where FSB is the value you have chosen from ClockGen.exe); every time you change the value, you have to modify the text file to include the new value, of course.
    4. Create a shortcut to CG-ICS951412.exe; right click the shortcut and select “Properties”; add “-file=filesave.txt” to the “Target” field so that it should look something like this:
    “C:\ClockGen\CG-ICS951412.exe -file=filesave.txt”
    5. In order for Windows to load the program at boot, place the shortcut in the Startup folder.

  • Overclock the K7N2G-L w/ Barton 2500+

    I need help with the BIOS in able to overclock my CPU.  I have W6570MS V.3.7 BIOS the most up-to-date version.  I need to know exactly what option in the BIOS that I need to change to get my CPU over 2GHz.  I am trying to aim for 2.5GHZ if possible.  Is there a way to get step-by-step instructions that are for my board and processor?
    Any and all help are greatly appreciated!!!
    Thanks!

    Quote
    Originally posted by foshizzle
    I know but exactly how???? I am new to overclocking and need to know what exactly do I need to change in BIOS to get to those speeds.  Thanks
    Hi,
       If you're new to overclocking I would suggest you do a lot of reading on the subject. If you don't have proper cooling and know exactly what you're doing you had better have a deep wallet. I've had many people come to me with fried components because they were overclocking without having proper knowledge and experience. I have seen people come to these forums looking for help in overclocking only to get irate when things didn't go right. If you still want to go ahead with it their are plenty of sights on the subject, just do a search.
    Good Luck  
    Rob

  • Problems with KT3 Ultra2 and Barton 2500+

    I have a very big problem.
    I buy new Athlon XP2500+ ty my board.
    KT3 Ultra2 support 166FBS, but AGP and PCI bus is overclock (83/42) and my system is very instabile. Now using 133FBS. Can I fix bus to 166/66/33???
    My configuration:
    Win98SE+WinXPSP1
    MSI KT3 Ultra2 (bios version 5.7)
    Athlon 2500+@1900+ (Barton 11*133, 1,65V)
    + Spire 5F271B1L3 FalconRock II™
    256MB RAM DDR-400 Kingmax (CL2 at 333, 1.7V*)- sorry I mean 2.7V*
    Daytona ATI Radeon 9000 64MB DDR
    SB Live! Value
    AMD 10/100 LAN adapter
    40GB Seagate HDD
    Lite-on combo
    FDD teac
    add: 4 april 2004 at 15:17
    My PSU is Emko 300W ''JS-300 P4''parametres in:http://www.emko.cz/emko_cz/index.html
    1900+ temps: CPU:                          Chipset:2500+ temps: CPU:                          Chipset:At 2500+
    Stability configuration si withount SB Live! value and LAN.
    result:     Memtest86                       - O.K.
                  3DMark2001SE build330    - O.K.
                  SiSoft Sandra 2003           - O.K.(burn-in: CPU and memory test 20time)

    what sandra version did you use?
    next to temps and psu, please tell us, what bios is installed. barton cpus require version 5.7
    "(CL2 at 333, 1.7V)" did you mean 2.7V? cause 1.7V are llittle too low.
    sj

  • Barton 2500+ in KT333 Ultra ARU w/ 9800xt help me

    here are my specs,
    AMD Athlon XP 2500+ Barton @ 12.5 x 175Mhz (green chip from early june03)
    MSI KT333 Ultra ARU
    512Mb x 1 Corsair XMS PC2700
    Ati 9800xt w/ 3.10 Catalyst
    SB Audigy MP3 w/ latest driver
    Antec smart power 350WMax,(i think constant is
    I only get 16000 marks in 3dmark 2001se. AAandAF are application select.  ive read how people with slightly lesser ati boards are getting 20k marks.  what is the bottleneck in my system?  I cannot run a 10 x 200Mhz on my barton, it won't POST.  Is it my power supply or is it my ram?both?  do i need 512x2 ddr400 to overclock more?  I got it to boot w/ error at 12.5x185, but that doesn't help at all.  how can I get my 3dmark score up?

    I cannot run a 10 x 200Mhz on my barton, it won't POST
    it never will as board has only 1/5 divider so agp would be 80 and pci 40

Maybe you are looking for