HOLD button for serivce POs

Dear All,
How to activate HOLD functionality for service orders. HOLD functionality is there for material purchase orders but not for service purchase orders.
Please help.
Nil

Not Possible for service item
Please see the help from SAP
Enjoy purchase orders cannot be put on hold if any of the following
criteria apply:
o The PO contains service items
o The PO contains "third-party" items
o Commitment errors are involved
o Subsequent (period-end volume rebate) settlement is involved

Similar Messages

When restarting my iPad 1 freezes on the apple logo. It even does when I try and do a reset by holding power and the hold button for 10 seconds.

When restarting my iPad 1 freezes on the apple logo. It even does when I try and do a reset by holding power and the hold button for 10 seconds.

If the reset doesn't work, you have to force the iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button.
5. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: You need to be patient and repeat the above many times to recover your iPad. Data will be lost.

My Ipod is frozen on a blank but lit up screen, no response to holding buttons for 10sec??

Ipod is frozen on a blank but lit up sreen with no response to holding buttons down for 10sec...

If a hard reset does not work by holding the Sleep/Wake + Home buttons at least 15 seconds or until the Apple logo lights up, then try a restore.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
 In Memory of Steve Jobs 

Black screen with white rolling back continuosly. I can shut it down after holding buttons for 45 seconds but when I turn it back on it starts again.

I am trying to save my pictures on my PC so I can get the iOS7 upgrade. I plugged it in to my computer to do so and my screen is black with the white rolling ball. I can reset after holdign home and off for 45 seconds btu when I turn it on the same thgin. I cannot shut it off. How do I get this tos top so i can move forward?

1) Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414
2) If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/HT1808
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download

My iphone 4 wont turn on. it justr randomnly turned off and i have tried to hold the home and sleep buttons for a minute and also tried to put it into recovery mode but nothing is working?

my iphone 4 wont turn on. it justr randomnly turned off and i have tried to hold the home and sleep buttons for a minute and also tried to put it into recovery mode but nothing is working?

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

My MacBook Pro 13in Mid-2010 won't start unless I hold the power button for about 10 seconds! Help Please!

Hello.
I have a MacBook Pro 13-inch (mid-2010):
Processor: 2.66GHz Intel Core 2 Duo
Memory: 4GB 1067 Mhz DDR3
Running Mac OS X 10.7.2
Yesterday I opened my computer (was sleeping as usual) and the screen just flasehed white and the computer powered off. The magnetic electricity thingy was connected and was green, so it was fully charged, and connected to the electricity.
Since it powered off, I tried turning it on again, and again, one second after starting to boot up, screen flashed white and the computer powered off.
I read somewhere I should hold down the power button longer, so I did, and it booted up. That's why I am able to write this. But every time I turn it off or put it to sleep, it does the same thing when I boot up.
If I don't hold the power button for 10 seconds or so, the computer won't work.
Then today, I did a backup of my entie hard drive, just in case. Later, I started using Excel, and about 1 hour after I was on it, suddenly it got really slow. Like I would click on a program like Safari, and it would take over 30-45 secs to start and be ready. And my computer is usually really fast!
I went on the Internet again, started in safe mode, boot up with option+command+P+R to reset PRAM, and nothing worked. Then suddenly on one turn-off/turn-on (since I can't restart because the computer only starts if I hold the power button for 10 seconds), again it is working at normal speed.
What can this be? Any ideas?
I really appreciate your time and help in advance
Gaby

GabyBA wrote:
I forgot to say I had already tried that as well. Just in case, I just tried it again and there was no change :S
Are you running the Apple-supplied RAM? Have you run Apple Hardware Test? I don't know what else you've tried, but this may be time to do a fresh install of Lion if you have not done so since installing Lion.

I 'think' my Ipod Touch is in recovery mode and people say to hold the power and home button for 10 sec and i did, but its still not turning back on. Plus its dead and wont charge

I 'think' my Ipod Touch is in recovery mode and people say to hold the power and home button for 10 sec and i did, but its still not turning back on. Plus its dead and wont charge. PLZ HELP ME!!!!

- If in recovery mode the screen will have an iTunes logo with an USB plug.
- Have you tried connecting it to your computer for a n hw and then see if it appears in iTunes. If it does restore the iPod.
- If screen is blank, try placing he iPod in recovery mode and then restoring. For recovery mode:
iPhone and iPod touch: Unable to update or restore

My ipad mini does not restart when i press and hold the home and power buttons for a minute or more. what do i do? i really need to access some information on it. please help.

my ipad mini does not restart when i press and hold the home and power buttons for a minute or more. what do i do? i really need to access some information on it. please help.

You need to connect to iTunes and restore.
iOS: Not responding or does not turn on
You may need to put the device into recovery mode, this is covered in the link on this page.
Did you back up the device?

When I went to update my iPod touch on iTunes, it said unable to update then the iPod shutdown and no longer showed connected in iTunes. I have tried holding down both buttons for up to 3 mins with no luck turning it on, even after a full charge. Help?

When I went to update my iPod touch on iTunes, it said unable to update then the iPod shutdown and no longer showed connected in iTunes. I have tried holding down both buttons for up to 3 mins with no luck turning it on, even after a full charge. Help?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My iPod touch 5th generation had white screened an it won't let me rest it by holding down the home button an the power button for ten seconds I've pulled it in to iTunes an its not being detected what can i do as its starting to over heat?

my iPod touch 5th generation had white screened an it won't let me rest it by holding down the home button an the power button for ten seconds I've pulled it in to iTunes an its not being detected what can i do as its starting to over heat?

If you can't get it to shut down or restart when holding down the Home and Sleep/Wake buttons and you can't get it recognized in iTunes to restore it, the iPod may have suffered a hardware failure and will need to go to Apple for service. Someone else here may have additional suggestions, though.
There is no "fifth generation" iPod touch, by the way, just for the sake of clarity; not yet, anyway.
Regards.

"You need to restart your computer. Hold down the power button for seve..."

Hello,
I have recently been getting this same message "You need to restart your computer. Hold down the power button for several seconds or press the Restart button." whenever I start up my computer. It happens about 95% of the time. I have been reading on different forums that I should reset the PRam and the NVRam and I have been doing so and it does help as it does EVENTUALLY start up (sometimes takes me 5-10 min. to get it to start up).
I have also read that it may be the RAM that is loose, so I did check that and made sure that the ram is properly placed (which it is).
I don't know what else I can do. Should I reformat and reinstall Mac OS X?
Here is the exact error form the dump:
IOAPIC: Version 0x20 Vectors 64:87
AppleACPIPlatformExpert::start failed
panic(cpu 0 caller 0x55c095): "Unable to find driver for this platform: \"Macbook 2,1\".\n"@/SourceCache/xnu/xnu-1504.9.26/iokit/Kernel/IOPlatformExpert.cpp:1389
Debugger called: <panic>

Well just got around to installing the new HDD and RAM yesterday, and I am sad to say... that the problem persists. :/
I reseated the memory and made sure they were in there properly, and I also installed the HDD and ran DiskUtility before I erased/reformatted and installed a fresh version of MacOSX Leopard, then updated to Snow Leopard.
As long as I am using my computer everything works fine, the problem occurs when the machine is shut off or put to sleep for a long period of time. Because when I shut it off and turn it right back on a few minutes later it works, or if I shut the lid and open it 10-20 min. later everything works fine, it's only when the machine is off or asleep for long periods of time.
So, I do not know what else can be wrong.
Should I try to take out the old RAM and just leave the new module in and see if that works out? See if that specific module is faulty?

How to disable MOH for "on Hold" button.

CUCM 6.1
When on a conference call if a user presses "on Hold" button, music is played for all participants and nobody can hear anything. How can I disable music on hold for all users?
Please note, I could disable MOH for conferencing. But this is different issue. This is e.g. when everyone is in a conference (no matter what conference system, it could be ready talk, meeting place,...)and a participant receives another call and wants to answer the other call, in this situation I don't want any MOH played for other participants.
Thanks,
rdianat

I first tried "suppress MOH for conference" by service--> service parameters -->select server --> select callmanager --> go to "clusterwide parameters(Feature-General) --> change the "Suppress MOH to conference Bridge" to true"
This did not work. The reason is that these users are accessing an internet coferencing system like "ready talk" and not a cisco conferencing system, so for Cisco this does not appear to be a conference but it is like a regular call.
I only have two callmanagers which also serve as MOH servers.
Media Resources-->Music On-Hold Server -->Set Run Flag to "NO"
This is explained in "MOH FAQ" from cisco.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_qanda_item09186a0080094766.shtml#q21
The other way of doing this is not to assign any MOH server to the MRG or create a device pool without any MOH. (Media Resource Group set to NONE)
Although the above disabled the MOH, still the TOH "Tone on Hold" which is beep-beeps played every 10 seconds was annoying. So I increased the interval to 20 seconds by the same instructions in "MOH FAQ" how to disable / change TOH. Go to same page explained above but to "clusterwide Parameters(Device-General) and change "Tone on Hold Timer" Value to 20.
rdianat

I have reset my iphone 5c and now has apple logo on the screen. I have tried holding home and lock buttons for 10 seconds, but to no avail. How do i sort this please ?

I have reset my iphone 5c and now it has the apple logo on the screen. Nothing is happening, apart from the screen going off for a few seconds, only to go back to black screen and white apple log. I have tried holding home and lock buttons for 10 seconds, but to no avail. I did a reset on settings as the IOS 8 was just slowing down my phone horrendously. How do i sort this please ?

Hi MartinH78,
If your iPhone isn't responding or won't start up past the Apple logo, you may find the troubleshooting steps outlined in the following article helpful:
iOS: Not responding or does not turn on
Regards,
- Brenden

My 4th generation ipod touch is not turning off when i hold the wake button for few seconds the Voice Control Function Starts Automatically.Please help me to get out of this problem.

My 4th generation ipod touch is not turning off when i hold the wake button for few seconds the Voice Control Function Starts Automatically.Please help me to get out of this problem.

Sorry i mistakenly made this question. It was alright. No Problem At ALL

Hi I was using whatsapp on my iPhone5.I was not able go to the main menu by pressing the center button so I hold on to the button for 2 seconds.Then the whole display turned out to be black

I was not able go to the main menu from whatsapp by pressing the center button so I hold on to the button for 2 seconds.Then the whole display turned out to be black & white. how can i fix it?

Hello monicaa003,
Thanks for participating in the Apple Support Communities.
If your iPhone display turned black and white after holding down the Home button for 2 seconds, first try pressing the Home button again to go to the main menu (Home screen.)
For reference, holding down the Home button for 2 seconds will trigger Siri if that feature is enabled:
About Siri - Apple Support
If pressing the Home button doesn't return you to the main menu, try restarting or resetting your iPhone:
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
Additionally, if Whatsapp is not responding or working as expected, see the troubleshooting steps at this link:
If an app you installed unexpectedly quits, stops responding, or won’t open - Apple Support
Best Regards,
Jeremy

HOLD button for serivce POs

Similar Messages

Maybe you are looking for