HomeHub 2 disconnects and reconnects after 4pm eac...

Every day  at roughly 4pm my home hub has started disconnecting and reconnecting, this continues most of the evening then it seems fine the next day. 
After looking at past post i have looked into the settings on my hub and copied which i will paste below.
any help very much appreciated
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 0:05:20
Downstream
4,608 Kbps
Upstream
448 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Fast
Noise margin (Down/Up)
6.2 dB / 10.0 dB
Line attenuation (Down/Up)
50.0 dB / 28.5 dB
Output power (Down/Up)
19.1 dBm / 12.6 dBm
Loss of Framing (Local)
0
Loss of Signal (Local)
0
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 0
CRC Errors (Down/Up)
1 / N/A
HEC Errors (Down/Up)
N/A / 0
Error Seconds (Local)
1

connection time is only 5min is that due to manual reset or router dropping connection?  are you using wired or wireless for your devices  I ask because it the router was dropping connection as often as you say I would expect your connection to gave moved to interleaved instead of fast  your noise margin at 10db is higher than normal 6
try quiet line test  dial 17070 option 2  should be quiet and best with corded phone
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Similar Messages

  • ICloud mail does not reconnect in Mail application on MacBook Pro after disconnecting and reconnecting iPhone or after sleep

    iCloud mail does not reconnect in Mail on my MacBook Pro after sleep or after disconnecting and reconnecting my iPhone. This only happens when I use my iPhone as a 3G-modem and not when I am on Wi-Fi. The only solution seems to be to quit the Mail-application and restart it again. Then Mail reconnects to iCloud.

    Hi horstp,
    Given your description of the issue (works on other Macs), it may be worth trying to set up that account by itself in a new test user on the iMac to see if it can be isolated to a user-specific file. You may find the following article helpful:
    Apple Support: Isolating an issue by using another user account
    http://support.apple.com/kb/TS4053
    Regards,
    - Brenden

  • HT1600 AFTER UPLOADING UPDATE , THERE IS A BLINKING LIGHT ON THE APPLE TV DEVICE WHICH IS NOT STOPPING EVEN IF YOU DISCONNECT AND RECONNECT

    AFTER UPLOADING UPDATE , THERE IS A BLINKING LIGHT ON THE APPLE TV DEVICE WHICH IS NOT STOPPING EVEN IF YOU DISCONNECT AND RECONNECT

    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
        1.    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
        2.    Connect the micro USB cable to the Apple TV and to your computer.
        3.    Reconnect the power cable (only for Apple TV 3)
        4.    Open iTunes.
        5.    Select your Apple TV in the Devices list, and then click Restore.
    (You may already have a micro USB cable if you have a camera or other digital device)

  • If connect iPad to my TV every time the clip is finished I have to disconnect and reconnect the iPad for new clip playing.

    If connect iPad to my TV every time the clip is finished I have to disconnect and reconnect the iPad for new clip playing.

    1. Why don't you purchase it from Apple? I'd be wary with eBay sellers - and, after all, Apple posts their stuff everywhere, even if you live in a country without a localized Apple store webpage or local (physical) Apple stores.
    2. when it comes to adapters / cables like these, NEVER purchase ANYTHING non-Apple-manufactured! Most of the cheap(er) knock-offs don't work! That is, don't try to save on going for a cheaper alternative - it most likely won't work.
    Here are the links:
    http://store.apple.com/us/product/MD098ZM/A
    http://store.apple.com/us/product/MC552ZM/B

  • IPod sync failed. Disconnect and reconnect, then try again.

    Over the past month or two, I have gotten this message quite frequently with my iPod. It usually happens after I sync my iPod once, leave it hooked up to my iMac for charging, and then try to sync again (sometimes not even more than a few minutes later). I also often have trouble getting my computer to recognize the iPod (or getting my iPod to recognize that it's supposed to start syncing) without having to disconnect and reconnect it and shake the USB cord around a few times.
    I had a little bit of this problem with my iPod 5G and XP PC, though no "iPod sync failed" messages ever. This is a new iPod classic and an iMac. What's going on?
    Does anyone else have this happen to them?

    I'd been having this same issue and kept trying all the suggestions on the forums to no avail. Then I just disabled "Enable Disk Use", which required me to first disable "Manually manage music & videos". I unchecked all of my music, videos, podcasts and photos, applied the settings, then chose which media I wanted in my iPod. I synced successfully and even cleared it out completely a couple of times to re-sync. No issues anymore.

  • Constant disconnecting and reconnecting with WPA2 enterprise wifi. Any available solution?

    I know it can't be the wifi because as recent as yesterday on Mavericks everything was fine. Now after the update it constantly disconnects and reconnects as much as a few times per five minutes! I've read on Reddit other people are having similar problems. Hopefully Apple fixes this soon.

    Looking at the Console.app logs, it seems that the machine decides to bounce between two APs:
    17/10/2014 19:22:07.000 kernel[0]: ARPT: 36912.641537: MacAuthEvent en0   Auth result for: 20:c9:d0:a7:91:9e  MAC AUTH succeeded
    17/10/2014 19:22:11.000 kernel[0]: ARPT: 36915.802654: MacAuthEvent en0   Auth result for: 20:c9:d0:af:a3:54  MAC AUTH succeeded
    17/10/2014 19:22:14.000 kernel[0]: ARPT: 36918.976595: MacAuthEvent en0   Auth result for: 20:c9:d0:a7:91:9e  MAC AUTH succeeded
    17/10/2014 19:22:17.000 kernel[0]: ARPT: 36922.166582: MacAuthEvent en0   Auth result for: 10:9a:dd:87:5b:93  MAC AUTH succeeded
    17/10/2014 19:22:20.000 kernel[0]: ARPT: 36925.323944: MacAuthEvent en0   Auth result for: 10:9a:dd:87:5b:93  MAC AUTH succeeded
    17/10/2014 19:22:20.000 kernel[0]: AirPort: RSN handshake complete on en0
    17/10/2014 19:22:20.000 kernel[0]: wl0: Roamed or switched channel, reason #3, bssid 10:9a:dd:87:5b:93, last RSSI -73
    17/10/2014 19:22:20.000 kernel[0]: en0: BSSID changed to 10:9a:dd:87:5b:93
    17/10/2014 19:22:20.000 kernel[0]: en0::IO80211Interface::postMessage bssid changed
    17/10/2014 19:24:01.000 kernel[0]: ARPT: 37026.789184: MacAuthEvent en0   Auth result for: 20:c9:d0:af:a3:54  MAC AUTH succeeded
    17/10/2014 19:24:05.000 kernel[0]: ARPT: 37029.979376: MacAuthEvent en0   Auth result for: 20:c9:d0:af:a3:54  MAC AUTH succeeded
    17/10/2014 19:24:05.000 kernel[0]: AirPort: RSN handshake complete on en0
    17/10/2014 19:24:05.000 kernel[0]: wl0: Roamed or switched channel, reason #3, bssid 20:c9:d0:af:a3:54, last RSSI -65
    17/10/2014 19:24:05.000 kernel[0]: en0: BSSID changed to 20:c9:d0:af:a3:54
    17/10/2014 19:24:05.000 kernel[0]: en0::IO80211Interface::postMessage bssid changed
    17/10/2014 19:27:06.000 kernel[0]: ARPT: 37210.896826: MacAuthEvent en0   Auth result for: 20:c9:d0:a7:91:9e  MAC AUTH succeeded
    17/10/2014 19:27:09.000 kernel[0]: ARPT: 37214.088570: MacAuthEvent en0   Auth result for: 20:c9:d0:af:a3:54  MAC AUTH succeeded
    17/10/2014 19:27:12.000 kernel[0]: ARPT: 37217.263429: MacAuthEvent en0   Auth result for: 20:c9:d0:a7:91:9e  MAC AUTH succeeded
    17/10/2014 19:27:15.000 kernel[0]: ARPT: 37220.429042: MacAuthEvent en0   Auth result for: 10:9a:dd:87:5b:93  MAC AUTH succeeded
    17/10/2014 19:27:18.000 kernel[0]: ARPT: 37223.509291: MacAuthEvent en0   Auth result for: 10:9a:dd:87:5b:93  MAC AUTH succeeded
    17/10/2014 19:27:18.000 kernel[0]: AirPort: RSN handshake complete on en0
    17/10/2014 19:27:18.000 kernel[0]: wl0: Roamed or switched channel, reason #3, bssid 10:9a:dd:87:5b:93, last RSSI -76
    17/10/2014 19:27:18.000 kernel[0]: en0: BSSID changed to 10:9a:dd:87:5b:93
    17/10/2014 19:27:18.000 kernel[0]: en0::IO80211Interface::postMessage bssid changed

  • Connection keep disconnecting and reconnecting itself

    Few days ago I installed arch on this laptop (HP Pavilion 15-b129el Sleekbook), I started installing and configuring stuff on it today and I encountered a couple of problems with the connection and xorg (which I won't discuss in this thread).
    To make it short, launching wifi-menu will show correctly all the available networks, it won't, however, actually connect.
    I tried netctl which successfully connected and gave me a chance to download and install programs, sadly the connection doesn't last long but it seem to reconnect by itself.
    For instance, I was updating with pacman -Syu now and as it was downloading the package linux3.10.6-2-X86_64 it kept disconnecting to reconnect after a bit and restart downloading the package from where it stopped.
    I decided to test if my laptop had hardware problem and booted into my xubuntu partition, I launched a ping command and it seem to be stable, sometimes it takes a bit longer than it should to receive new signal but it don't seem to lose connection at all.
    Suggestions?
    Last edited by arkindal (2013-08-14 10:53:14)

    Update: Today wifi-menu managed to connect with a similar behaviour of netctl, connection works fine for a while, then doesn't work, then work again, tested with the ping command, I'd say a bit over a hundred pings works fine, then it stop for a while saying network unreachable, then working fine again.
    Changed title to fit better the situation.

  • Controller keeps disconnecting and reconnecting

    Hi thereI have recently had a problem with my Dualshock 4 controller connecting to my PS4. I took ps4 to my dads while i was staying there and everything was fine. Since i returned home i set up ps4 as normal but my controller keeps disconnecting and reconnecting itself. It is not a charge issue as it has been charging for 2 hours now. I am just sitting on the home screen now and controller is plugged in by usb cable and just keeps connecting and reconnecting but remains on charge when it disconnects. Any help would be much appreciated

    Turn off the PlayStation 4 by pressing the power button on the front panel. The power indicator will blink for a few moments before turning off.Once the PlayStation 4 is off, press and hold the power button. Release it after you've heard two beeps: one when you initially press, and another 7 seconds later.Connect the DualShock 4 controller with the provided USB cable and press the PS button on the controller.Choose option 5 rebuild database.For home hub. Open the web browser on a computer or device connected to your Hub and go to http://bthomehub.home to open the Hub ManagerClick on SettingsEnter the admin password. Unless you've previously changed it, you'll find the default password on your Hub settings card on the back of your Hub. If you have changed it and now forgotten it, you can use the password override feature to set up a new passwordClick on the "Advanced Settings" tab, then click Continue to Advanced SettingsClick on the "Wireless" tabTo manually select the wireless channel for the "2.4 GHz" band:Go to the 2.4GHz page and select a channel from the drop down menu next to "Wireless Channel". First try channels 1, 6 or 11Click Apply to confirm the change. Then wait 60 seconds for your computer to automatically discover the new settings. There's no need to change any settings on your computer 

  • Skype disconnects and reconnects alot

    Ok so i have seen a couple posts with this issue but not exactly the same. My skype calls will work for the most part but then sometimes it will start to disconnect and reconnect constantly. Sometimes when i reconnect to the call i can hear the other person but they can never hear me. Sometimes when i reconnect i cant hear them at all. But every time we reconnect after the disconnecting starts they can never hear me and it keep disconnecting until i do my tempory fix i found. The only way i have found to fix this is to close skype completely and reopen it. That is the only way i have got it to work again. Any ideas why this is happening or what i can do to fix this

    Hi, funbuilder030,
    To help diagnose this issue more closely, some more information would be helpful:
    - Hardware you use (laptop/phone/tablet brand and model)
    - Operating system (version and updates installed)
    - Skype version used
    - Internet connection used and the carrier
    Anticipating what Community Ambassador Ruwim may also ask,
    Please,  run the DirectX diagnostics tool.
    Go to Windows Start  and in the Run box type dxdiag.exe and press the OK button. This will start the DirectX diagnostics program. Run this diagnostics and save the results to a file. Please, attach this file to your post.
    Be aware that you will have to zip this file before attaching it here.
    ... and also,
    Open Windows Event Viewer * -> Custom Views -> Administrative Events. Look for any recent error messages with timestamp corresponding to Skype crash. Copy and paste here the text from the General tab.
    *  http://windows.microsoft.com/en-us/windows/open-ev​​ent-viewer#1TC=windows-7
    You can also right click on the Computer or My Computer icon and select Manage.
    Providing all of this information will help our Community's diagnosticians!  Thanks in advance. 
    On behalf of the Skype Community Moderation Team,
    Elaine
    Was your question answered? Please click on the Accept as a Solution link so everyone can quickly find what works! Like a post or want to say, "Thank You" - ?? Click on the Kudos button!
    Trustworthy information: Brian Krebs: 3 Basic Rules for Online Safety and Consumer Reports: Guide to Internet Security Online Safety Tip: Change your passwords often!

  • Several times a day my HP Laptop disconnects and reconnects to my WRT600N router.

    I’ve installed a new WRT600N.  (Firmware Version: 1.01.35 build 5_20080115).
    My install was a “Linksys EasyLink Advisor” guided and is generic.  SPI Firewall Protection is enabled.  Security Mode is enabled for WPA-Personal.
    The laptop I use with router is an HP/Compaq 6710b (also new), running XP Pro.  The built-in WiFi adapter is a “G” type (Intel PRO/Wireless 394ABG) with “Windows Wireless Network Connection” enabled.
    Presently I don’t use the “N” capability of the router.  However, I plan buy a 2nd laptop with an “N” WiFi adapter soon.
    The router works well…most of the time. Signal strength is “Very Good”.  However, several times a day my HP Laptop disconnects and reconnects to the router.
    Each time this happens I get a “Linksys EasyLink Advisor” prompt stating “Network Problem!...the connection to the router is not working”.
    After experimentation I realize that most often the connection will restore by itself…or worst case; I can re-detect and restore the connection using either the “Linksys EasyLink Advisor”  wizard OR the “Windows Wireless Network Connection” wizard.
    Besides losing the connection, the most annoying part of this is that after the connection is restored and the “Linksys EasyLink Advisor” wizard message remain indicating: “Network Problem!...the connection to the router is not working”.  
    Suggestions?

    There are many causes for poor wireless connections, and many solutions:
    First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
    Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
    In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
    Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
    Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. If your current network is not listed, enter its info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".
    If the above does not fix your problem, download and install the latest driver for your wireless card.
    Some users have reported improved wireless performance by switching from WEP to WPA encryption.
    If you continue to have problems, try the following:
    For wireless n routers, try setting the "n Transmission Rate" to 162 Mbps, and the (wireless g) "Transmission Rate" to 54 Mbps.
    If you still have trouble, download and install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
    Hope this helps.

  • Ipod disconnects and reconnects

    My iPod keeps disconnecting and reconnecting to my computer. This is really annoying because it will only appear under devices for a few seconds before disconnecting. Then after about 10 seconds it will connect again and appear under devices again. Why is this happening?
    iPod Nano (1GB)   Windows XP  

    Mine is doing a similar act. It'll sorta update and then disconnect. This is getting very annoying. I've done everything short of re-installing windows xp!
    Athlon 4800 Dualcore   Windows XP Pro   2 GB Ram, SP2

  • Hey all..i hv problm .. i cant connect wifi properly ..its stucking itself after evry 5 mints and reconnect after evry 5 mints ..plz helpe...sorry for bad english but hope u will understand

    hey all..i hv problm .. i cant connect wifi properly ..its disconnect itself after evry 5 mints and reconnect after evry 5 mints.. signal showing but there is no avail internet ..plz helpe...sorry for bad english but hope u will understand..

    If your connection won't 'stick', check for interference in that area from other devices on competing channels, etc.
    Configure your choice of band/channel with interference robustness, but mainly reduce the sources to be sure it's not just a too noisy environement.
    Still no joy, be sure your software is up to date and then walk it into the nearest Apple store for a professional opinion
    Good luck in any case.

  • Macbook won't start or charge unless I disconnect and reconnect the battery connector each time .

    I have a late 2011 model Macbook Pro, 10.7.5 OS and I've had no issues whatsoever up until a week ago. The night before if stopped working I did everything as usual, did some HW, emailing then I shut it down. I woke up the next morning and it wouldn't turn on so I figured it was dead, so I got my charger plugged it in and got no light, green or orange. What I got was a faint green blinking on the charger light and my battery level indicator wasn't working. I thought it was my charger but it wasn't because worked fine on my girlfriend's Macbook.
    I googled and tried PRAM and SMC to no avail. When I tried the SMC I didn't take the battery out I just disconnected the connector (Don't know if it makes a difference) and Voila it worked and I thought I fixed the problem. I turned it off and the next day the same thing, I have to disconnect and reconnect the battery connector each time for it work. Other than this issue I have no problems, mac runs fine while it's on and I shut it down or restart it for awhile after I reconnected the battery but if I try to turn it back on or restart it hours after I've done that then it won't work . One thing I may add is after I reconnect and plug my charger in, the light is green for about 5 seconds (even though it's not fully charged) then turns orange .
    I'm guessing I need a new battery or logic board , but I'll keep my fingers crossed .
    I won't be able to set up an appointment until next week but I would like to see if I could get any help here in in the meanwhile.
    Thanks !

    Hi, I dont know if this may be the cause as i too have the same problem. But it only occurs after i disconnect my Iphone from my macbook pro.
    The Macbook has worked perfectly and then all of a sudden last week it started to shut down after i would disconnect my Iphone 5.
    The mac wouldn't restart, charge or anything.
    I tried all the trouble shooting reccommended, Shift Alt command button combinations. ( there were a fair few ) None worked.
    Then i found out about disconnecting the connector.
    This fixed the problem.
    But alas, It done it again after my next sync.
    This has done it 4 times now. And only when i disconnect the iphone after using itunes on the mac. I done it all correctly 3 times and the 4th time i just pulled it out with out ejecting from itunes, but still done it.
    The iphone Syncs perfectly. I get everything i want onto the iphone. But for some reason as soon as the cord is disconnected from the mac BOOM. Dead mac.
    If i leave the cord and the phone plugged in but still eject the phone it doesnt shutdown tho.
    I found if i shutdown the macbook, then disconnect the iphone cord once the mac is completely shut down then my mac will start back up again with no problems.
    As i said i dont know if this is the cause of your problem and if it will help you or not? But if not, maybe it will help someone else out who finds your post?
    Hope you get your problem sorted
    Chris

  • IPhone 3G WiFi disconnects and reconnects every few seconds

    hey guys
    i just updated my phone to 4.0.1 and lately (before the update as well) my iphone has been playing up on me
    Like the wifi works and all but when i go to the appstore for example...it disconnects and reconnects constantly and stops downloads cause it stops like 1-2 secs it begins.
    i tried everything resetting network settings, turning phone on/off, DFU mode, taking off WPA and broadcasting the modem, it just doesnt want to work.
    Mind you this was working for around a month and just like 2 days ago this happens and i cant fix it. I even tried the McDonalds free wifi and that works but its very slow couldnt download anything but it didnt disconnect/reconnect
    Also the router is working on both the Wii and PS3 without a prob, just these 2 days on my iPhone
    any suggestions?

    I upgraded my 3G to 4.0.1 and had the same issue - could not connect to my secure wireless network. It DID, however, connect to my neighbor's unsecured network. I tried resetting Network Settings, resetting All Settings, rebooting my iPhone, rebooting my router, multiple times, all without luck.
    I had to do a FULL RESTORE from iTunes, install as a NEW PHONE and now I can connect to my wireless network. But even after the full restore, I don't see any improvement in phone performance. Still slow, still laggy, still crashes (requiring a reboot) with some apps. And now I have a phone set back to factory default. Grr.

  • Internet keeps disconnecting and reconnecting.

    Hello
    I have Verizon fios, and my internet keeps disconnecting and reconnecting immediately, over a 10 minute period, many times a day.
     I am not wireless. Im directly connected to my router.  It seems to happen at the same time each day, lately its been getting worse, it will happen about 3-4 times a day .  It will start disconnecting, then reconnect, every minute or so, for about 10 minutes.
    Ive contacted verizon over the phone, they kept saying to check my router and wire (which I did, and everything seems to fine), after a while on the phone with them, they just hung up on me.  I checked my router,wire,computer, and everything is fine there.
    Can anyone help me? This is beginning to be a major issue.
    Please help
    A.W.

    I was having this exact symptom for weeks and it was driving me crazy! However, I did find the problem and a solution and maybe it will benefit others as well.
    Problem: I had added another device that had a static IP that conflicted with my router's IP.
    Solution: In my case, I changed the other devices static IP, but you could also set the other device to use DHCP (best) or change the Verizon device IP.
    This can occur for a variety of reasons, but the most common is when you add another router (like a wireless router). Another common cause is that another device on your LAN is running a DHCP server, and since the Verizon router is expecting to be the sole DHCP server they can server the same IP #s out. I've had many cases where a Windows machine just magically started serving DHPC requests, and all versions of Windows I've tested for some reason have the DHCP server running by default! 
    Hope this helps! 

Maybe you are looking for

  • Selection-screen design

    Hi everyone, I am working on a project for which I have to design a selection-screen. The requirement is such that there are 3 obligatory fields to be filled by the user, which are as follows: P_LAUFD(parameter,obligatory-date), P_LAUFI(parameter,obl

  • Script works in PowerGUI, not in ISE or from powershell.exe

    Hi, I am trying to integrate with the Manage Engine Password Manager PRO Rest API.. I have some code working on my desktop where I currently use PowerGUI this was all seemingly working correctly.. I have then gone to execute the code from a window on

  • Safari/E-mail problem. Can't log out!

    We've just purchased our first Mac and so far everything has been great. A problem we've encountered is with our email accounts. We both go to the same school, so we both use the same email that the school provides. However, even when one of us click

  • Implementing KANBAN-WM

    Hi Gurus, we are implementing KANBAN with WM for VERP materials in the pharmacology factory. We actived the replenishment strategy 0006 (for WM) and created a supply area, but SAP didn´t let us use the PK01 to create a new control cycle. System oblig

  • HT204370 Is it possible to change my purchase to the same cartoon, but with another spoken language?

    I bought the movie Cars for my kids on my apple tv. It was the english version, but I thought it was possible to change the spoken language to Danish. It wasn't. Now it seems I should have bought a different version of the film; the danish version. I