Hooking up to new router

All worked fine until I hooked up new Apple router. Test shows all is successful. Printer says all is fine, but when I click to print it says "printer is not responding"
This question was solved.
View Solution.

Add printer solution took care of the problem

Similar Messages

Have a new router, Amped, and now the printer will not print wirelessly from my iMac.

HP Photosmart Premium ePrint Wireless Model C410a.
Mac OS
I just hooked up a new router-Amped. Now the printer will only work with a "wire" and not wirelessly. It worked with my previous NetGear router.
What do I need to do to get it to work?

Your new router is likely using a different subnet than your old router. Go into the printer's wifi settings and make sure it is in the same lan as your router. Follow the printer's wifi set up instaructions.

Airport extreme unable to connect to new router

We just received a new router from our cable company. The old router worked with our airport extreme just fine. After hooking up the new router the airport extreme could not connect to it. I received the following error "error occurred while trying to access the apple wireless device. Make sure your connection is valid Error -6753" So then I tried to power off and reset the Airport extreme. The button was stuck on my reset button. I did figure that out and was able to click the button. But even if I would hear the audible click when i held down the reset button the amber light never flashed rapidly? Not sure what else to do. I have turned off the modem, unplugged the router, plugged them back in. etc. I just don't know where to go from here.
Thanks!
jodi

Were you able to get the AirPort Extreme to reset back to factory default settings, as LaPastenague detailed?
The amber light needs to flash rapidly for about 6-8 seconds during the process to indicate that the reset is taking place correctly. Once you release the reset button, the light will stay solid amber for 15-20 seconds or so, then change to slow blinking amber.
We are a bit confused as well, since in your first post you mention that you received a new router from the cable company, then later in the post, you mention that you have a (separate?) modem.
In the most recent post, you mention that you have a new modem. Is the new router from the cable company the same device as the new modem? Or, do you have a new modem and another new router in addition to the AirPort Extreme?
Can you clarify on exactly what devices that you have? Make and model numbers would help. We know that you have an AirPort A1408.

Hooking iPhone up to my new router

I just purchased the new 6th generation airport extreme. I have a 2nd generation square airport extreme I am successfully using to extend the network. The problem is it does not work for my iPhone 4s. My iPhone will connect to the new router, but not the relay. Any suggestions?

if you set it to extend the network then you should connect to the new router the other routers will extend the wifi range if the SSID you see as the new router

New router and can not connect wirelessly

Installed a new router that changed my security from a WEP to a WPA2. I have connected to the printer(7410) through ethernet cable and changed the security settings but the printer will not connect to my router. I am currently printing by ethernet cable hooked directly into the router. When i try to use the printer interface to cinnect to router the only option that comes up is WEP.
Any ideas?
This question was solved.
View Solution.

The printer will support WPA, but not WPA2. It may have previously been connected to WEP and is expecting that. Let's reset it:
From the front of hte printer: Setup > Network > Restore Network Defaults. Now try the Wireless Setup Wizard from that same Network menu.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Need suggestions for new router running mac with eyeconnect,and ps3

We have the latest version of leopard on our 24" imac and we have eyeconnect ver. 1.6 we need to buy a new router and i want one that is very easy(like plug it in and walk away)to use. The main priority for this is not having problems streaming media to our ps3 via eyeconnect or medialink. Wireless or wired whatever would be the best i have never actually had an airport only linksys and have been unhappy with most of them any advice welcome about the router or getting eyeconnect to be recognized by the ps3 once its hooked up. Thank you

What I have in my house is an Airport Extreme with it's two (n,b or g) wireless connections for older non-N wireless connections. I then got a D-Link DGS-2208 10/100/1000Mbps 8-Port Desktop Green Ethernet Switch 8 for fast subnet sharing in the house. This speed is important for HD video sharing for from the external I have connected to the USB2 port on My Extreme.
Note: My Extreme is in "Bridged mode" because it sits behind a wired router that acts as the DHCP server.
Getting a router with Gig Ports and and USB2 port for an external to store/share files (videos mainly) to all my networked devices. The USB2 port on the Extreme was the deciding factor for the extra cost and this handy port making any USB2 external into a networked drive. Plus my older iPhone 3GS only does G it was a no-brainier because of the dual wireless.
The GIG switch is future proofing yourself for the years to come.
Plus I called the extreme but it is a Time Capsule that is just and extreme with a built-in disk.
One more thing: Use CAT6 cables in your network.
Message was edited by: satcomer

Can't browse network with new router - HELP!

My old WRT54G died a few days ago. I replaced it with a WRT54GL which was the closest match. Since installing the new router I can no longer browse my network. I configured the new router with LELA as per the instructions suggested. Could that have changed something? All the machines can get on the internet and I can ping all the machines through the command line but when I try to look at the workgroup in the my network places window I get an error message that says:
"Workgroup not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The network path was not found."
When I run the net view command in the command line that also results in an error.
When I hook machines together with a crossover cable everything works fine so I have to assume it's some setting in the new router that is preventing the browse list from working. Here's what I've tried:
Turned off firewalls both on the local machines and on the router - made no difference
Made sure all machines are in the same workgroup - they are
Made sure browser service and the peer networking services are running - they are
Made sure all machines are on the same subnet - they are because they can ping each other
Now here's something really strange. When I rename the workgroup on all machines they can see each other. Once I switch back to the name "workgroup" they can't see each other any longer and I get the error message.
I run a small business and need to share files quite often. I would love to be able to get a NAS server but I can't find any that will work with ALL of my machines. Most of my machines are running Vista at this point but a few are still XP Pro. One of my machines is XP Pro and cannot run SP2 which prevents a lot of newer software and devices from running on it. This is why I really need to get my file sharing ability back.
Any help is greatly appreciated.
Mike
Solved!
Go to Solution.

I solved the issue and wanted to post it in case someone else has the same issue. One of the machines uses a Linksys WGA600N Dual Band Gaming adapter as it's wireless adapter. Technically speaking this actually a bridge. I needed to restart it. That solved my issue.
Mike

New router does not see the Internet

I replaced my MI424WR Rev. D with a new MI424WR Rev. I. The old version D work very well put I wanted the WPA2 sercuity of the the new router. I follow the instructions that came with the router and hooked up the router as instructed. Lights on the router started to light up and turn green except on: The Intnet light. After waiting ~15 minutes, I went through the usual procedure of checking the cable, unplug the router and replugging it in and resetting the router. I even reset the ONT. I was wondering is there something else I can do before having to clean out the closet and call in a tech to see if he or she can fix it.
Solved!
Go to Solution.

You need to release the IP address from the old router. You can also plug in the new router and call Verizon and have them do it.

WRT 110 - New Router not detected

I am having problems with the setup wizard. Im getting "New router not detected". It's all setup correctly. I've reset modem, router and rebooted 100 times atleast. I can get on the internet when the modem is conected through the router. Also, I cant get to the 192.168.1.1 router setup. I have set up other linksys routers without problems. We are on Time Warner cable internet. Please help before I smash this thing.

I have an older Linksys (twin antenas) product so bought this for my son in Ohio. He tried to connect the router using his laptop and could not do it...after calling support (Punjab in India) they could not resolve the problem or begin to figure it out. After watching a 6 year old on YouTube hook up a router, I figured it couldn't be that hard so I told him to send the WRT 110 to me along with his laptop.
After trying the install myself (using the supplied CD), I could not connect to the internet via the wired laptop-router-modem either. So I figured the wireless device of the laptop may be interfering with the router. So I went to Control Panel>>Network Connections>> and right clicked on "Wireless Connection" and clicked "DISABLE". After that, the laptop DID connect to the internet via the ethernet cable.
When I tried to login to the new wireless network using another laptop, I could not connect after repeated attempts using the letter "O" and the number "0" of the WEP code generated by the CD install. I finally COPIED and PASTED the WEP code to a Word document, saved to a stick, then transfered the doc to the wireless laptop. After COPY and PASTE of the WEP code to the LOGIN >>>SUCCESS.
The wireless connection works fine two floors away from the router as does my old antenna router did, so the "range" problem reported by others is a mystery to me. Don't know why the "support" couldn't have solved this problem....I'm not a real computer nerd, but can do "trial and error" fixes.
Bottom line: router works fine and is better looking than the "antenna" ones but who cares??? I go for the blinking lights anyway <g>

Configuring my new router!!!???

So i just bought a new router at wally world (walmart..). I am in a dorm room right now, and i wanted to get a router to get some wifi going on here, because of course the campus wifi doesn't reach my room.... so anyways, i got this router to solve that. I know my campus registers MAC addresses when we arrived here, so i know i need to clone my MAC address from my laptop to my router. And i'm trying to do this... but i can't...
first of all, i can't even install the CD, because the network here wont let my router connect...
second, i'm not sure how to change the MAC address on my router, because i don't know how to change the settings on it without first being on a network..
Is there any way i can change the MAC address without being connected to a network? Like hooking it up to my laptop and chaning the settings that way?
I know this might sound and look confusing, so ask any questions of you need!!!
Thank you

I am not familiar with the 160 GUI, but you should be able to look through it and find a page that allows you to clone a MAC address. It's probably on a sub-tab under the Setup tab.
There will be either an entry field to manually enter a MAC address or a button the will clone the address from the PC you are currently connected from. Whichever you try, the cloned address should be the same as the one the scholl has registered.
If this is in a dorm environment, you will ABSOLUTELY want to change the admin password for the router, change the SSID from the default and set up wirelss authentication (use WPA or WPA2, not WEP). You might consider disabling admin access for wireless clients also, so that you have to connect the ethernet cable if you want to make any config changes in the future.
Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
D-Link DSM-320 (Wired)
Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
SonyBDP-S360 (Wired)
Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
IOmega StorCenter ix2 1TB NAS
Linksys WVC54G w/FW V2.12EU
and assorted wired and wireless PCs and laptops

I have an wireless printer and a new wifi router. I have set the printer and iPhone / iPad correctly to the new router but when i try to print it won't recognise the air printer. Help. All was working fine on my old router

I Have a new wifi router and have set up my iPad / iPhone and wireless printer correctly to the new router but I can't print from the iPad and iPhone. It keeps saying ' no AirPrint printer found'. Help please!

Start with the most basic thing that you can try. Unplug the router from power for about 30 seconds, and restart the printer and the iPad and plug the router back into power.

Can not connect All in one 209b to new router for wireless printing....

Have an HP laptop and All in one priner 209b. All was working fine, wired and wireless printing. Then we had to upgrade our ATT Uverse router. Everything works...even wireless laptop and printer when connected to laptop. However, can't get printer to printer wireless since it has the old router info. I used the disk but when it asks to you to pick the printer, I choose the printer but it says printer now found ??? what ???? and this is with the cable connected. I do not have the wizard on the touch screen but I did reset to factory settings hoping it would load new router info but it does not. How do you manually enter router into for wireless printing. Is it best to delete the printer and reinstall as new...wired and then wireless ???
I am about to call an outsite company and pay the outrageous charge as the help on HP is not working. Thanks

Try this utility:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02114394&cc=us&dlc=en&jumpid=reg_r1002_usen&lc=...
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

Can not connect my wireless printer to the new router.

Can not connect my wireless printer to the new router.

Can you please provide details:
1. The make and model of printer
2. Make and Model of Wireless Router
3. Is your printer connection wireless to router or a cable to PC
4. What have you done or attempted to do to establish a connection?
5. Any further info to assist

HT201335 It got nA new router today and wanted to turn on apple tv but my remote app on iPad and iPhone will not recognize apple tv. Btw- I do not have apple tv remote.

It got A new router today and wanted to turn on apple tv but my remote app on iPad and iPhone will not recognize apple tv. Btw- I do not have apple tv remote.

It reboots it but unplugging can also rectify communication issues like this. A restore would be the next step.

HP 6520 won't scan with wireless connection and new router

My printer scanned fine before. Got a new internet provider=new router and now I can't scan scan anymore. The computer is connected wirelessly. The computer says it cannot communicate with the scanner. Same if I try from the printer front panel, it says it can't communicate with the computer.
The router seems like the obvious cuprit, but nothing in the router settings or manual suggest anything that could be blocking the scanner communications. The router firewall is turned-off.
Printing works fine, and I can connect to the printer through its IP address. The user interface can see the printer status, check ink levels, everything. Everything works but scanning. I've re-installed software multiple times, tried turning off firewalls and tried HP Scan and Print doctor. It's not much help.
I'm at wits end.
-ETC

Hello @etcottle , and welcome to the HP Forums!
I see you are experiencing scan connectivity issues. I would like to help!
I would recommend powering down your computer, disconnect the power cord from the printer and the power outlet, and remove the power from your router for 60 seconds.
After 60 seconds, plug the router back in. Once the router has begun broadcasting, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
After the printer is on, re-run the wireless setup.
I'd also suggest this document:
Wireless printing center Troubleshooting Issues
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Hooking up to new router

Similar Messages

Maybe you are looking for