Host Memory Consumed at VM for prime infrastructure 2.0

Dear All,
I have prime infrastructure 2.0 from 12 day ago i have logg on NCS (1. Message: CPU: 85 crossed down threshold: 90) and when see host memory from prime infrastructure VM i see that Host memory consumed so i make down time and increase the memory from 24 GB to 40 GB.
today i see th host Memory increases to 38.03 GB within 12 day I add only 30 Site map contained 45 AP or more(all site maps found on PI 568)
please feed me this is normal behaviour or not and why host memory increase . when the host memory consumed i monitor that All NCS functionality doesnt work. Please Advice.
Prime infrastructure 2.0
VM 5.1.0
Thanks

Hi Satyaki,
Try to reboot the WLC ,if possible and then check the status of the issue.
Regards-
Afroz
**Ratings Encourages Contributors ****

Similar Messages

  • Export Data for Prime Infrastructure

    I started an Export for Prime Infrastructure on my LMS 4.2.3 box several days ago and it is still running.  There are approximately 3600 devices being exported from LMS I am guessing it should not take this long.  Would like to kill the process but I am not sure which one to stop?

    That would be lms he'd need to restart Afroz.
    Depending on the platform:
    Net stop crmdmgtd then net start crmdmgtd (Windows server)
    Application stop LMS / application start LMS ( soft or physical appliance)
    There is probably an individual process you could restart but I don't have it at my fingertips. I haven't exported one that big but usually it would only be a matter of minutes to complete. It's just a simple csv file.
    Sent from Cisco Technical Support iPad App

  • Cisco Prime Infrastructure 1.3 - SNMPv3 can´t get CPU, memory info.

    Hi,
    I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
    Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
    Thank you.
    Eduardo

    Hi Eduardo:
    SNMPv3 is indeed supported for general administration.  There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring.  Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively?  Bug CSCug78869 keeps things from working well when changing SNMP versions. 
    If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it.  While it's not going to specifically address this issue, there are a lot of really good fixes in it.
    Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20

  • Prime Infrastructure 1.3 ERROR at Backup restore

    Hi everyone,
    we are currently in migration phase of WCS to Prime 1.3 and at this moment we are encounter the following error:
    We are migrating the databases at appliance 1, then backup the databases and restore it at appliance 2.
    This process is needed for the central migration of 3 4 databases.
    Today we wanted to restore a migrated database on the new appliance and got this error message:
    ERROR : There is the mismatch in the following configuration parameter(s) of this machine when compared to the machine where the backup was generated: SWAP Memory
    ERROR : This may affect the performance of the current machine. Hence aborting restore process.
    % Application restore failed
    Both appliances have the same version when the database was backed up, appliance 2 has already the final licenses while appliance 1 run without licenses at the moment (for the migration process).
    Can anyone help me regarding this error message? I couldn't find anything in the net.
    Best Regards

    Today we could figure out that the update 1 for Prime Infrastructure was blocking the restore process.
    You can't remove the patch. When you try the command "patch remove NCS..." you get an error that this command does not apply on this patch version...
    We installed a fresh version 1.3.0.20 without patch and could restore the database without problems.
    So be careful with this update...

  • Prime Infrastructure 2.0: Open Database Schema Support available?

    Hello,
    I searched the forum for an Open Database Schema Support for PI.
    I only found Open Database Schemas for the Cisco Works LAN Managemet Solutions and Cisco Prime LAN Managemet Solutions.
    Exists an open Database Schema Support for Prime Infrastructure 2.0 as it exists for the older LAN Managemet Solutions ?
    Thanks.
    Bastian

    Programmatic interface to Prime Infrastructure is done via the the REST API vs. any open database schema.
    There are published reference guides here. For the most up to date information, please see your PI server itself. In Lifecycle view, the help menu has a link to the server-based API information:

  • Cisco Prime Infrastructure patch 2.1.1 - installed or no?

    I’ve reinstalled new Cisco Prime using the newest ISO image version 2.1.0.0.87. After that I installed the patch file (pi211_20140630_01.ubf) for version 2.1.1 and rebooted the server. After that I don’t see any information in CLI that I have version 2.1.1 installed. When I type sh ver I still see version 2.1.0.0.87. The only information which confirm this information is a “Software update” site in GUI interface where status of the patch is "Installed". Is this normal behavior?
    Regards
    Lukas

    Patch installed through ubf not showing info in CLI and login page
    CSCup78886
    Description
    Symptom:
    After installing the "2.1.1" patch (filename pi211_20140630_01.ubf) for Prime Infrastructure 2.1.0.0.87 through the Administration > Software Update page and issuing an "ncs stop/ncs start" sequence from the CLI, the version information on the Prime Infrastructure login page, the CLI output of "show version" or Help > About pages does not indicate version 2.1.1.
    Conditions:
    Workaround:
    At this time, there is no workaround. Please confirm proper patch installation on the Administration > Software Update page. Column "Installed' with the value "Yes" and column "Pending Restart" with the value "No" indicate that the 2.1.1 patch is indeed correctly installed.
    Last Modified:
    Jul 22,2014
    Status:
    Open
    Severity:
    6 Enhancement
    Product:
    Network Level Service
    Known Affected Releases:
    (1)
    2.1(1)

  • Upgrade Cisco Prime LMS 4.0 to Cisco Prime Infrastructure 2.1

    My company has asked me to migrate Prime LMS 4.0 to Prime Infrastructure 2.0 for a client and can not find the guide, the questions are? the migration is possible without an intermediate step? and There is a guide to update LMS 4.0 to PI 2.0 ??
    Thanks in advance.

    Prime LMS 4.2.2 added support for the PI template directly:
    Export Data for Prime Infrastructure
    Cisco Prime LAN Management Solution supports data migration to Prime Infrastructure 1.2. This feature enables user to export the Device Credentials Repository (DCR) data from LMS 4.2.x versions to Prime Infrastructure 1.2. The data backup status and backup location are displayed at the bottom of the Export Data for Prime Infrastructure page. The data being exported from LMS and the data imported back to PI are listed as follows.
    Data exported from LMS
    •Device Credentials Repository (DCR)
    •Software Image Management
    •Config Archive
    •Change Audit
    •Syslog
    Data Imported to PI
    Device Credentials Repository

  • Prime Infrastructure 2.0 license count

                       HI,
    How much licenses does I have to count for 1 stack of (lets say 4 memebers) ?. I.E 1 stack is  1 license or is 1 stack #members in the stack licenses ?
    Before 1 stack was 1 license, but I've heard some things that this should be changed ?
    Jan

    It's the same scheme for Prime Infrastructure 2.0, i.e.:
         "If a switch stack is managed through a single IP address, then it counts as only one device"
    Source.

  • Is Cisco Prime Infrastructure 1.2 or 2.0 compatible on UCS ?

    hello, can we install Cisco Prime Infrastructure 1.2 or 2.0 on UCS C22, C220M3 or NCS Hardware Appliance without using VMware ?
    thanks.

    Hi,
    Unfortunately, this isn't yet supported for Prime Infrastructure.
    you have Installed VMWare first.
    Thanks-
    Afroz
    [Do rate the useful post]

  • Migrate from Prime LMS to Prime Infrastructure

    I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2.  I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well.  I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
    My real question is about Syslog handling.  All of the managed devices are currently sending Syslog data to LMS.  As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
    Thanks for any help you can provide.

    Putting LMS up against Prime Infrastructure is like comparing Apples to Oranges.
    LMS is a very mature product and Prime Infrastructure is in it infancy stages...
    My suggestion would be to leave the current LMS system up and running; bring a Prime Infrastructure server up with a Demo License; add a few of each type of device to your Prime Infrastructure server; setup a proof of concept scenario to prove you can do everything in Prime as you can do in LMS.

  • Cisco Prime Infrastructure 1.3 - TFTP backup WLC not working

    I don;t get the the background task "Controller Configuration Backup" working. I want to use default TFTP.
    When i look in the logging i see 2 of three WLC's succesfully backuped there logging. Is their a log file where you can see what is happening?
    With kind regards,
    Martijn.

    Hi Martijn:
    If you go to the controller's GUI to Commands > Upload File and manually trigger the TFTP Configuration backup, does the process complete as expected?  If not, whatever's causing that problem needs to be addressed first.
    When someone wants to do a config backup from the command line, they give a series of commands
    transfer download datatype config
    transfer download mode tftp
    transfer download serverip x.x.x.x
    transfer download path ./
    transfer download filename myBackup.cfg
    transfer download start
    The Controller Config Backup background task is just the SNMP version of "transfer download filename " and "transfer download start".  If these other required settings aren't already there, the task isn't going to set them (the humans have to).  If there's a problem with writing out the file on the server, or packet routing issues to get to the server, the task isn't going to see those things, it just knows that the answer to "transfer download start" wasn't "Okay!"
    As for watching this processing in logs, go to Administration > Logging, and set the logging level to Trace for the modules SNMP and System, and click Save.  Then kick off your backup attempt, allowing it to fail.  When it does, return to Administration > Logging, and click the Download button to retrieve the logs.zip file.  The activity should be in the ncs-x-x.log file. 
    If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it.  While it's not going to specifically address this issue, there are a lot of really good fixes in it.
    Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20

  • Linux command/shell script to find Memory consumed by JVM in EBS,SOA

    Hi All,
    Could anyone please let me know the following:
    a)Linux command/shell script to find Memory consumed by JVM for every 1 minute frequency interval in EBS R12, SOA suite
    b)Percentage of the Heap memory usage by the JVM for every 1 minute frequency interval in EBS R12, SOA suite
    Thanks for your time!
    Regards,

    user10088255 wrote:
    Hi All,
    Could anyone please let me know the following:
    a)Linux command/shell script to find Memory consumed by JVM for every 1 minute frequency interval in EBS R12, SOA suite
    b)Percentage of the Heap memory usage by the JVM for every 1 minute frequency interval in EBS R12, SOA suite
    Thanks for your time!
    Regards,Please see these docs.
    JVM: Guidelines to setup the Java Virtual Machine in Apps Ebusiness Suite 11i and R12 [ID 362851.1]
    Generate JVM heap dump in E-Business suite 11i and R12 [ID 462550.1]
    11i: How To Use Jconsole to Monitor JVM with Oracle E-Business Suite 11i [ID 415455.1]
    Configuring various JVM tuning parameters for Oracle E-Business suite 11i and R12 [ID 567551.1]
    Script to find Apache, Java, Jinitiator, Forms version and JVM details for Oracle E-Business Suite 11i [ID 466890.1]
    JVM Memory Monitoring, Tuning, Garbage Collection, Out of Memory, and Heap Dump Analysis For SOA Suite Integration 11g [ID 1358719.1]
    How to Perform Memory and Thread Analysis on SOA [ID 1450293.1]
    Thanks,
    Hussein

  • Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Prime Infrastructure/ Assurance is  positioned today more towards managing network elements and network performance,  rather than server infrastructure. We are in the process of adding Datacenter  component support, with more focus on Nexus and UCS- due later this  year.
    Having said that, Prime Infrastructure allows the system user to  add custom SNMP polling templates, which can then be used for polling any SNMP  based values from any SNMP enabled device. These can be used to collect the  information you specified below and the polled information will be available in  dashboards and reports.

  • Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

    Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
    What would be the procedure for configuring?
    Thanks in advance.

    Hi,
    Enable "logging host x.x.x.x "  command to enable logging
    check the below link:
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
    FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
    Operate > alarm and events > syslogs
    Thanks-
    Afroz
    ****Ratings Encourages Contributors *****

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

Maybe you are looking for