Hot cloning & cold cloning

i need hot cloning & cold cloning documents

This is something strange to me. What do you mean by "hot cloning & cold cloning".Database cloning is part of Application cloning. When you clone Oracle Application, you need to run pre-clone and post-clone on both the application and database tiers. To clone the database, either you shut it down and copy the files (cold backup), or you can use RMAN to recreate the database (hot backup).
What I know is, using Hot/Cold Database backup can be performed cloning of a database. How this cloning & cold cloning relates to Oracle ApplicationsAlready answered above.
Only the possible method for Cloning Oracle Applications Release 11i/12i is with Rapid Clone.For non-AutoConfig enabled systems, you cannot use Rapid Clone. Instead, you need to follow the steps in "Cloning Oracle Applications Release 11i" paper/note.

Similar Messages

Cloning : hot cloning and cold cloning

hi
how to clone in EBS R12.I am a core DBA student currenly working as trainee in EBS dba.
can anyone explain ....
i am requesting some details on hot cloning , cold cloning and user managed cloning techniques.
in user managed cloning i need to run adpreclone.pl then copy some files then whats for when using rapid clone ??
rgrds

See the below metalink notes on cloning..
Note 230672.1 - Cloning Oracle Applications Release 11i with Rapid Clone
Note 362473.1 - Cloning E-Business Suite Using Hot Backup for Minimal Downtime of Source Environment
Note: 799735.1 - Rapid Clone Documentation Resources, Release 11i and 12
Note: 216664.1 - FAQ: Cloning Oracle Applications Release 11i
Hope this helps
Regards
http://www.oracleracexpert.com
Click here for steps to [Oracle version upgrade from 10.2.0.x to 10.2.0.4
http://www.oracleracexpert.com/2009/10/oracle-version-upgrade-from-1020x-to.html
Click here to [Download Oracle Grid Control and ASMLib and Install
http://www.oracleracexpert.com/2009/08/download-oracle-grid-control-and-asmlib.html

AMP 3.1 -- Oracle E-business Suite 11.5.10.2 CU2 Hot Cloning

Hi,
New release 3.1 for Oracle Application Management Pack is available now.
In last release i.e AMP 3.0 version hot cloning was supported for E-Biz 12i version only.
Amp 3.1 documnetation says about smart cloning.
Is hot clone of Oracle E-Biz 11.5.10.2 CU2 from grid using AMP 3.1 new versionpossible now?+
Regards,
Manish Patil

Hi Manish;
Is hot clone of Oracle E-Biz 11.5.10.2 CU2 from grid using AMP 3.1 new versionpossible now?+Please check this and see its helpful for your issue
Regard
Helios

Hot Cloning

I am planning to hot cloning using RMAN backup , using this link http://newappsdba.blogspot.com/2009/06/r12-cloning-from-rman-backup-using.html
Within this link there is a step to tar database node tech_st
tar cvfzp TEST_dbhome_myserver.tar.gz db/tech_st
can i do above tar when database production is in open mode , i mean database open and users are connected to my application R12 , does it hamper the file doing tar in open mode for tar cvfzp TEST_dbhome_myserver.tar.gz db/tech_st?
OS RHEL 4.5
Khurram

but one step is missing in that blog that he is not changing the header of file with its original SID which would be in my case PROD , it can be changed by either DBNEWID utility or recreating contorfile with name SID UAT. If we do not change then with same domain 2 same db_name could not exist.

Highlight Hot and Cold toggle turns entire Image RED!

Hi,
I'm curious if anyone has a solution to this issue. I'm using Aperture 2.1.3 on a Macbook Pro running OS Version 10.5.7. I shoot Nikon RAW files and a while back when I hit the ever helpful Option-shift-H (to toggle the Highlight Hot and Cold feature), I end up with the entire image turning red (Hot). Now the histogram is fine, I just can't fine tune the hot and cold areas with the feature. . . I've tried reloading Aperture 2 from the original disk (I did not delete the original copy firs in fear of loosing my images).
This feature worked fine until about 6 months ago- it probably stopped working during one of the updates. . . The "creative" at the apple store scratched his head and suggested I post here for a solution. . . Any help world be appreciated.

In Aperture try this:
Go to Preferences (cmd+,) -> Appearance
Then set
Hot Area Display Threshold to 100%
Cold Area Display Threshold to 0%
You might have set hot to 0% which would cause all parts of the image to appear red.
Just play a bit with those sliders to get what you want.

Toggle on "Highlight Hot and Cold Areas"

Aloha all.
When ever I toggle on "Highlight Hot and Cold Areas" my image turns solid red. I know I must have a setting turned on or set too high but I can't figure it out? Anyone else with this problem? Solutions?
Using Aperture 2.1

In Preferences->Appearance, see what the hot area display threshold is set to. It should be 97 or higher.

Hot and cold backups

i am learning to take hot and cold backups and i am having doubts regarding restoring and recovering/
1. When restoring the cold backup .. i am copying the control and datafiles from the backup and then starting the database with reset logs is this enough?
2. When i am recovering a tablespace in hot backup .. i have replaced the file from backup. I need to do something with the archive log files. Where do i place them in the database? If i have done some transactions after taking the hotback.. will i loose those transactions?

"1. When restoring the cold backup .. i am copying the control and datafiles from the backup and then starting the database with reset logs is this enough?"
Yes, you are right.... also include password file in your backup file list...
2. When i am recovering a tablespace in hot backup .. i have replaced the file from backup. I need to do something with the archive log files. Where do i place them in the database? If i have done some transactions after taking the hotback.. will i loose those transactions?
You can place the old datafile at new location also. For hot backup, your DB must
be running in archive log mode, so you will not loose any transaction.....

Highlight hot and cold areas

When "Highlight hot and cold areas" is turned on I often get some blue outlines in a photo, but when I press "Z" (zoom) they disappear. What is going on?

Could be a number of reasons for this but nothing to worry about. You could try looking at the hot/cold threshold levels but you need to remember smaller images can't hold the same amount of data as large ones. Edge sharpening for example, on the large scale may contrast 10,000 pixels along a 1 inch line to the full size image. Now think what has to happen when the image is shown as a 7x5. Think of it in terms of Bit Depth. With 1 bit there is no grey area and choices have to be made about what to show. In this case it is not a perfect copy of the full size image. Allan

Hot and Cold area viewing confusing me...

Hi Everyone,
I've been using Aperture 2 since it came and I'm liking the workflow and integration with the rest of OSX. Today I stumbled upon something confusing. I was playing with the display hot and cold areas option and was finding that when I measured the hot areas with the loupe, that the color values weren't actually blown out...
For example, I had a picture of a rose that when zoomed in, I could see the detail in the petals but was still being flagged as blown out. When I did a loupe rgb read on a 1x1 pixel point, I found that the red value was around 211...I thought that hot areas are 255?
Maybe I'm confusing what "hot" means. I've even seen cases where the master image is flagged as having more hot areas even though it is less saturated and exposure level is lower.
Can something be wrong with the hot/cold area function? Can anyone give it a try and see what kind of values they are seeing with the hot and cold area viewer?
Thanks.

Hi stjuste
re Maybe I'm confusing what "hot" means. I've even seen cases where the master image is flagged as having more hot areas even though it is less saturated and exposure level is lower.
Thought I would check. Used a pic of a dancer at night with firebrands. Pic looks good as I shot it.
Measured the "Hot Spot' at 255, and some others at a lower value. The manual says:
Images may occasionally have overly bright areas where color information about the
area is beyond the standard limits of the Aperture working color space. For example,
white areas in an image brightly lit with direct sunlight, or bright flashes off a water
surface, may be so bright that their color is outside the working color space. In addition,
images may occasionally have black areas where color information about the area is
below the standard limits of the working color space. Aperture can display these “hot”
and “cold” areas of an image with tints on the image to help you identify hot and cold
areas. You may be able to adjust these areas and recover highlight and shadow detail
identified by the hot and cold area overlays by changing the exposure, the recovery, the
black point, or the gamma setting of the image.
This maybe of help.. maybe not. Probably like you I set up the pics how I want them not what any program tells me.
Interesting though. I will do a bit more checking.
Cheers
Tomix.

Hot and Cold + USB?

I know this subject has seen a lot of mileage, but I would like to offer my views on the CPU temperature problem / Cold boot
I have just purchased a KT600 Delta FISR Mobo, having had a very good experience with my KT4 Ultra.
To say it runs hot is an over-statement, my set-up is
AMD Athlon 2400
512mb 2700 DDR [266]
2 x 80gb HDD [ Maxtor & IBM ]
Now I must start by saying, that I like small cases as I have a nice desk and it has to sit inside a cupboad. So I like cases where the power supply sits to the side of the CPU and not above. Also the depth of the cabinet is much less with the CDRom almost touching the Mobo. On the KT600 with the power connecter where it is I cannot use that bay!!.
Also I like HDD caddies so all my PC's have always had HDD caddies and these have there own fans
The cases have two front fans [ Un-obstructed - no floppy ] drawing air in and the PSU draws air out of the back.
In addition to that I have fitted to the KT6 Delta a Exhaust Fan that also draws air out. So I think I have a good air flow.
Now before you say, what do you expect, well I have two of these cases the other one houses my KT4 Ultra and it is exactly the same config except that the power socket is at the back behind the connectivity outlets.
This PC runs at 21c in idle [ 2100 Palimino Athlon ] and 30c when working hard.
[ Qtec 450w PSU ]
So I have been experimenting and with the case open and the power supply lifeted out the temperature is 54c idle. Case closed and power supply in situ it rises to 64c idle.
Now I did have a Q-Tec 550w PSU and I have read your comments so I changed it for a 400watt with actual power ratings [ not peak ] and it made vey little difference. I measured the voltages straight out of the power supplies I have tried and the 12v and 5volt vary very little from PSU to PSU and very little on load
Also measuring the on board regulators I can not detect any variance in voltage that is in sympathy with the changes shown by MSI Core Centre
So looking at the MSI Core Centre,
VCore = 1.65
3.3 = 3.45
+5v = 5.03
+12v = 11.70 to 11.82
If I install CPUIdle the MSI Core Centre now reads
VCore = 1.65
3.3 = 3.45
+5v = 5.00
+12v = 11.94 [ Rock Steady]
CPU Temperature 49/50c idle [ whether the case is open or not ]
So what is CPUIdle doing? My guess it is making up for fluctuations in the voltage regulation [ It would seem that a more acurate 12volts gives to a lower CPU temperature ]
It is certainly making the Mobo stable, which suggest un-aided it is not as stable as it could be.
Something else I have noticed the CPU heatsink does not feel unduly hot.
USB
Something else I noticed, I have a external USB 2.0 HDD enclosure, housing a 40gb 3.5 Maxtor HDD.
When pluggged in the temperature will rise by 10 degrees
[ I use to leave it on all the time on my KT4 Ultra ]
[ But in fairness it also raises the temperature on the KT4 ]
The load must be having an affect on the power in some way
The enclosure has its own power supply but uses the 5v available via USB
All this leaves me wondering how to proceed. I am not an overclocker or a gamer I simply use my PC as a work tool. The most I ever do is to log in to my works router to administrate the network from home.
Cold Boot
Yes my Mobo also hangs on starting Windows when cold.
All in all I am not a happy bunny, and would like to know what MSI views are on this.
Finally Although PC Alert will install on my PC [ Windows XP Pro ] XP Cooler will not work. It keeps throwing up a HM_Driver load error. Any ideas?
Kind Regards to you all

Hi Guys
Thanks for your thoughts,
First osnavi
My mistake the memory is 333mhz CAS 2.5 All Ok here Sorry if I mislead you.
Fredrik Åsenius & osnavi
Yes I agree I do not have the ideal situation here, but I have had many PC's right from the IBM Blue Lightning and Dell 25mhz and my ex PC KT4 ran just fine in the same situation and same case [ and still does and it does not have an exhaust fan other than the fan in the PSU]
Incidently when the PC is in use the door of the desk/cupboard is open, but not ideal I agree. I draw cold air in the front and exhaust it out the back
The problem of temperature rise is the same whether the PC is in situ or sat outside on floor.
However the point is this, why does CPUidle regulate the 12 volt rail and as such, bring the temperature down?
Why does USB hardware cause the 12 volt rail to fall and as such the temperature rise
My guess is poor voltage regulation on the Mobo.
No amount of cooling hardware will cure this.
In short I think the regulatiion on the Mobo is poor, which is a shame as the Mobo has a lot going for it at the price.
Matkel
I would be interested to know what your temperature was before and after, and what BIOS version you updated from?
I have updated from 5.4 to 5.5 but I did not notice any improvement.
ALL
Surely the point here is, if there were no concerns on temperature then people like ourselves would not be talking and writing about it.
As I see it there is a temperature control problem and the focus should be on cause. As I said at the beginning, my observations led me to beleive that the temperature is directly linked to the 12volts supply.
What I would like to know is what 12 volt supply is Core Centre / PC Alert monitoring.
I think that those of you who have opted for a Top Quality PSU have cured the symptons because the PSU has better power regulation, but not the cause.
It is arguable that a PC should have a good quality power supply, but their are a lot os PC's out there that have a bulk standard 350w / 400w PSU of no particular brand and they don't have a temperature problem.
Kind regards
Paul

Hot or Cold Hook-Ups of the DVI

Many folks talk about their "hot" MB's, and problems associated with their DVI hook-ups. Nobody from Apple has stated just how the plug-in of the DVI to the MB should be done. I the "Old Days", before USB's and Firewire's, you'd never plug-in anything when the computer was on. So Apple, tell us what you recommend--a "hot" or a "shutdown" for the DVI plug-in?
Don
In NC
PS. NY's Going win!!!

Thanks, Morttt,,,
I certainly know Apple reps don't opine on this site--or even spy on it--, but many surrogates do. I've been with Apple since 2000, have all their products and love them. But, getting answers is like asking a question of Ms. Clinton or any other politician or lawyer. There ain't no answers most of the time.
All I want to know from the inside intelligentsia, is there a right way or a wrong way to plug-in the DVI!
Don

How can I balance (or eliminate) hot and cold spots in a photograph taken under mixed lighting?

I have recently purchased some high resolution color photographs of black and white drawings. It appears that they may have been taken near a window because the left side of the images are noticeably cooler than the right side. Can I change the temperature in selected areas of an image? If so how can I do this?

This is with just a masked Solid Color Layer set to Blend Mode Color, but you could also try Curves (which would allow to better control the color-change in relation to luminance), Photo Filter, etc.:

Internet is hot and cold on macbook

I've been having a lot of trouble with my internet on my Macbook Pro just for the past week. Basically it just gets really slow, or just stops responding to the internet. I know that the network is totally connected (it says so on the Airport ting) and my roommates who also have Macs are not having any issue with it at all. I keep restarting the computer as well as the router, and it usually does the trick, but often only for a short while (sometimes as little as a couple minutes) before I have to do it again. What can I do to make my internet work normally again?
I'm not very computer savvy so any little bit of advice would help. Thanks.

I have this too! I blogged about this topic here( http://www.olij.co.uk/whitenoise/os-x-snow-leopard-wifi-issues/) - it seems to be a more' longer term' fix, but essentially it still crops up about once a week and I've yet to resolve it:
essentially:
Trash the airport config file in /Library/Preferences/SystemConfiguration. Copy the file to somewhere safe (desktop) and then delete it in the original location and restart the mac whilst clearing the nvram.
I've been leaving with this problem for 18 months now, and to be honest I'm really growing tired of it. sigh.

Sony SR-82 Hot and Cold

Yes, I know there are at least two previous threads with conflicting reports of IM8 compatibility but I just ran across something curious. My parents SR82 is easily recognized by my Macbook running IM8 with the ability to import but their iMac will not. Exact same camera. We both have intel dual core and are running the exact same version of iLife. The only difference I can find is that my quicktime version is 7.2 and theirs 7.3. There is also a difference in behavior. When the camera is powered on and placed in USB mode, IM8 opens on my computer but iPhoto opens in theirs. What am I missing here?

Thanks for all the help Tom. I reconverted the mpeg's to Quicktime DV and they now show up without rendering.
As a side note, I finally purchased a memory stick for the HDR CX-7 and it imported into Final Cut like a dream...and....as Apple promised, I put the High Def footage into the timeline along with the converted mpegs and it all works together without a hitch. It would be nice if Apple could figure out a codec for those folks with mpeg2 cameras. It is a lot of workaround to get it where it needs to be. Apple got me for the Quicktime mpeg add-on...glad the Streamclip folks aren't so greedy!

Cloning issue

Hi all,
I have a Q?
when I am doing Hot cloning ..
I completed restoring ,init.ora parameter creation...etc
while creation of control file I did all those steps what ever we required .
while recovering the db by using archive logfiles It is asking more arch file are required.
I supplied what ever I do have in Arch destination even though it showing error (more recovery is required)
Q:shall I open the db by open resetlogs....is it works?
any alternate we have?

Yes cloning is not a full consistent recovery. It will ask for archive logs which not yet generated at target database.Just cancel the recovery after applying all available recent archivelog and open the database in reset log mode.
RMAN duplicate database command also does the same.

Hot cloning & cold cloning

Similar Messages

Maybe you are looking for