Hot pink printing out as red?

I am running Illustrator CC version 17.1 on Windows 7 professional.    I designed some patterns using hot pink (CMYK 0/95/20/0) and when I export to JPG they print out as red.  When I export I'm changing it to RGB.  I think I read online that you can't print hot pink using CMYK or RGB because it's outside the gamut of those colors.   If that's the case, how do I get hot pink?

HI Ann,
First off, when you exported to JPG did it look correct? Are you printing only from Illustrator?
Which printer are you printing to? If printing from Illustrator. In the print dialog box. Are you selecting Illustrator to determine the colors or the printer?
If your printer is a CMYK printer. Then you would not need to change the colors to RGB. Try printing directly from Illustrator as CMYK.
If you can provide details of which printer that you are using and which app that you are printing from. That would help.
Thanks
Scott

Similar Messages

  • T 420s cooling air coming out is very hot, finger print reader problem

    I am living in ruwais, abudhabi.i bought T 420s in last June from LENOVO  authorized distributor. Model number is 4174-KK4 and the sr no ***.
    Sometime the cooling air coming out is very hot, unable to keep the laptop on the lap.
    The cooling fan also replaced still the temperature is high.
    After replacing the fan I noticed that I noticed one of the screws was not fixed, I asked them to fix it, then they fixed it.
    I traveled back to my home 240 KM from the  authorized distributor service  center. when I started the laptop, the fingerprint reader was not working . Then I traveled back 240 KM to the  authorized distributor service  center to fix the issue. They fixed the fingerprint reader problem.
    Then now the SD card reader is not working. I was asked to bring the laptop to the  authorized distributor service centre.
    Can any one experience the same type of problems  with T 420s the cooling air coming out is very hot, finger print reader problem, card reader not working?
    The authorized distributor says for the service they can only cover 50 KM form the  authorized distributor service  center to the customer point, what is the conditions for the On site warranty ?. I am living 240 KM away from the authorized distributor service center from whom I bought the laptop.
    Moderator comment: Serial number(s) removed to protect member from mischief.

    Well clearly after the first incident. You need to check and us it verifying everything is working before leaving the service center or town its in. Go to a coffee shop and spend time using it and test each option is working.
    When the notebook its opened the finger print reader, card reader etc may not be connect properly or connectors not snap fully and disconnect. Mouse ultranav I have heard may also. But clearly you assume too much and you need to spend the time testing its working before leaving.
    These service center are only paid a fixed amount so they won't spend anymore time then they have to and address one problem you brought it in for.
    As for heat out put and over heating. There are many threads on these systems you can find and read about.
    Advice:
    - install Core Temp, this will monitor and display on the task bar you CPU core temp and you can see CPU load & Temperature at a glance if it approaching or staying near the max levels which will kill the CPU and/or motherboard due to cooking it. Its free just be sure to deselect any additional software from installing during the process. I use it on my notebooks. If the system is running high core Temp all the time you need to have it resolved or it will die and most likely out of warranty and/or your data will be lost if you don't have a backup as well. http://www.alcpu.com/CoreTemp/
    - use a laptop cooler. Its a flat pad you sit the laptop on you lap or table with usually two cooling fans that plug into the USB port for power. It will help cool the base of the laptop and other components inside will not be as hot. This will do nothing for the CPU temperature though.
    T520 Model 4239 Intel(R) Core(TM) i7-2860QM CPU @ 2.50GHz
    Intel Sandy Bridge & Nvidia NVS 4200M graphics Intel N 6300 Wi-Fi adapter
    Windows 7 Home Prem - 64bit w/8GB DDR3

  • How t print out selected values from a Jlist

    hi iam trying to get the selected values from a list to print out as a string but iam getting ,Invalid cast from java.lang.Object[] to java.lang.String.is there any way to get the selected values t print ut as a string?? import javax.swing.*;
    import java.awt.*;
    import java.awt.event.*;
    public class MultipleSelection2 extends JFrame {
    private JList colorList, copyList;
    private JButton copy;
    private String colorNames[] =
    { "Black", "Blue", "Cyan", "Dark Gray", "Gray",
    "Green", "Light Gray", "Magenta", "Orange", "Pink",
    "Red", "White", "Yellow" };
    public MultipleSelection2()
    super( "Multiple Selection Lists" );
    Container c = getContentPane();
    c.setLayout( new FlowLayout() );
    colorList = new JList( colorNames );
    colorList.setVisibleRowCount( 5 );
    colorList.setFixedCellHeight( 15 );
    colorList.setSelectionMode(
    ListSelectionModel.MULTIPLE_INTERVAL_SELECTION );
    c.add( new JScrollPane( colorList ) );
    // create copy button
    copy = new JButton( "Copy >>>" );
    copy.addActionListener(
    new ActionListener() {
    public void actionPerformed( ActionEvent e )
    // place selected values in copyList
    copyList.setListData(
    colorList.getSelectedValues());
    String s1 =(String)colorList.getSelectedValues();

    Since the JList method 'getSelectedValues' returns an object array you'll need to iterate through the array and cast each object in the array to a string as you access them.
    Object[] o = colorList.getSelectedValues();
    for(int count=0,end=o.length; count<end; count++) {
    String s = (String) o[count];
    Hope that helps
    Talden

  • Why doesn't my print-out look like the screen view?

    This happens every time I use Firefox.
    Whenever I try to print a listing from Ebay, the main picture is omitted from the print-out. Here is an example. This first link is to a screen-shot (Fn and PrtSc) of a typical listing on Ebay:
    http://s1176.photobucket.com/albums/x327/xvqgp/Firefox
    On the PhotoBucket page look for the image FirefoxScreen.jpg
    There's a big picture of the item at the left-hand side of the page.
    Now take a look at what I get when I use the Firefox 'Print' command (this is a scan of the printed page):
    On the same PhotoBucket page look for FirefoxPrint.jpg
    There's a big blank space where the main image should be!
    I have not been idle and have checked a few things before posting this question:
    1) I have attended to the print settings as highlighted in the helpful Firefox article on printer troubleshoting. It has not cured the problem.
    2) From the same article I have tried the 'Print' function on Internet Explorer. While it pains me to say this, I get the correct printing from Internet Explorer.
    3) Operating Firefox in 'Safe Mode' has not removed the problem.
    4) Operating in 'Normal' mode but with add-ons disabled has not removed the problem.
    5) When I hover the mouse over the main image on the Ebay page I get
    javascript:;
    in the bottom left-hand corner of the screen. Might this be a clue or is it a red-herring?
    I would be most grateful for help.

    Have you tried using the '''Print''' item at the bottom if that eBay page? <br />
    Or is that what you are using?
    Overall it isn't unusual for "print" to be a bit different than what shows on the "screen", that page may use @media for "screen" and for "print". The '''Print''' item on that page could be the difference, or the web browser might be following that code is you used the '''Print ''menu item or button''''' in Firefox. <br />
    http://www.w3.org/TR/CSS2/media.html#media-types
    Typically, the '''@print''' CSS code is used to hide navigation menu's ''(can't "navigate" to a different web page from a sheet of paper)'' and maybe advertisements ''(can't "click" on an ad that is on paper)'' from being printed out so that only the text of an article is printed to paper.
    Basically, it's probably not a fault with Firefox, but rather Firefox following the commands on the page put there by the person who authored that page, or a standard CSS "style sheet" used by eBay.

  • I attempt to send an e-mail to an address in my Directory and it comes up in a pink block with a red circled exclamation point at the end. "Clicking" on the circle brings a pop-up saying the address is not registered for iMessages.  How do I register ??

    When I try to address an e-mail to an address in my iPad's Directory, the name comes up inside a pink block with a red circled exclamation point at the right hand end.  "Clicking" on the red circle, gives me a pop-up saying the address is not registered for an iMessage.  How do I register my Directory addresses for an iMessage??

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Troubleshooting iMessage Issues: Some Useful Tips You Should Try
    http://www.igeeksblog.com/troubleshooting-imessage-issues/
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
    How to Send SMS from iPad
    http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
     Cheers, Tom

  • Office Pro 8000: Can't Print/Out of Ink Error even after installing new cartridge.

    When I tried to use my printer a few days ago, I received a "Can't Print: Out of Ink" error message concerning the magenta cartridge.  I had used the printer a few days before that, and had not received a low ink warning.  It seemed suspicious to me that I would have received an empty cartridge error message without first receiving a low cartridge warning.  The yellow and cyan cartridges read 70% full - all 3 were original cartridges.
    I purchased a new 940XL magenta cartridge and installed it per instructions.  Now I am getting a message that the new 940XL cartridge is empty.  I can shake the old 940 cartridge and hear liquid inside.  Obviously, the new cartridge is also full.  I've tried cycling power, reinstalling the software, etc, with no change in status.  If I swap back and forth between the old 940 and new 940XL cartridge, they are properly identified by type on my screen as the 940 or 940XL.  Due to the way the problem has presented itself, I don't believe it is a cartridge issue.
    Of course, problem first arouse on May 8th, and my warrantee expired April 26th.  Any suggestions?
    This question was solved.
    View Solution.

    I've solved my own problem, which was clearly a factory assembly defect.  I looked inside my printer with a flashlight in the area where the ink cartridges are installed, and found magenta ink sprayed inside the printer.  I disassembled the printer, and found that the magenta line had been damaged during assembly.  There are four ink tubes which exit from behind the ink cartridges, then make a U turn back toward the front of the printer.  Just after the U turn, they make another bend up-wards.  It is at this point that I found the damaged magenta line, directly above a screw on the right-hand side of the ink cartridge housing.  The lines are in a very narrow passage, and are held in place by several keepers molded out of plastic.  It appears that the lines were put in place in the keepers, then the screw inserted from above.  As I said, it is a very tight passage, and it would be very easy to damage the ink line at that point if the lines weren't carefully held back to insert the screw during assembly.
    To solve the problem, I removed approximately 1/4 inch of damaged magenta ink line.  I carefully cut the line with a sharp razor, to prevent collapsing the line or causing burrs to the tubing.  I then placed about 3/4" of self-sealing heat shrink tubing over one end of the ink line.  Next I spliced the line with a small piece of stiff plastic tubing from the handle of a cotton swab, which was a perfect, snug fit over the ink line.  Being careful not to collapse the ink tube or cause further damage, I gently twisted the ink line back and forth until the ends were butted up inside the cotton swab splice.  I then positioned the heat-shrink tubing over the splice, and shrunk it with a hair dryer.  The heat-shrink tubing I used has hot-melt glue applied to the inside, which further aided in making a leak-proof splice.  Again, there is not a lot of room, so the splice had to be kept small.
    I reassembled the printer, reinstalled the ink cartridges, and powered up the printer.  After the normal, long start-up delay, I printed several full-color test sheets, and all was fine.  The magenta cartridge that I had installed previously now shows that it is full, and the remaining cartridges also read the levels that they had prior to disassembly.

  • Photosmart printer not printing out new ink colours

    Hey guys, I own a HP Photosmart b109a and have for a couple of years with no issues.
    About 4 days ago we brought some new ink cartridges for the printer as it had run out of colour ink and we were wanting to print out photos since we had heaps of photo paper and had thought it would work out cheaper than going to a store and paying for heaps of prints.
    It was the correct ink used but on the first print everything came in shades of blue, no other colour had printed, so after removing the printhead I noticed it had been covered in blue ink as if it had leaked, so I cleaned it as shown online, but then only the black ink would print. I tried printing things with colour only and it would print but come out blank?
    No issue with the ink would pop up and cartridges were shown to be full.
    After much messing around I finally found how to do a cleaning cycle but only ran one as I didn't want to waste ink and didn't know if it would work.
    Eventually the blue and yellow ink started to print and my photos came up as green in colour, but still no Magenta.
    After moving from house to house I no longer have the disc to this printer so can't run the HP solution centre as it refuses to find the printer which my Windows 7 has found. I can't even remember how I found the cleaning cycle to try and do it again.
    I've tried running many washes and printing heaps of coloured pages but the most I got was magenta appearing as a faded yellow.
    So last night I tried to soak the head in hot water overnight as someone insisted it was clogged, which it also looked to be. This morning it was again a lot cleaner but now no colour will print! Only black ink!!
    Any help with what can be done!? Getting these photos printed is super important as it's due to a loss of a family member and after paying for new ink that can't be returned, we can't afford to print at a store  
    Thanks in advance!

    No one has a solution? Might just add, an old Calidad cartridge that requires you to carefully remove the chip of an old cartridge then add it to theirs, works perfectly in my printer right now....? the other inks don't want to work though....?

  • How to control print-out in GI Slip based on storage location

    Hi Experts,
    Presently my smartform - GI Slip is giving print out for each line item. But the requirement is: no. of print out will depend on no. of storage location, independent of line item. Since GI Slip is a collective slip hence its showing same details for each line item. The print out are first taken from MB1A and then MB90 is for reprocessing.
    How can I control the no. of printouts based on storage location
    Please help me in this issue...
    Thanks in Advance...
    Pinki.

    You have to modify your driver program,
    Ex: Loop at < internal table>
    AT NEW <storage location>
    <New-page>
    End at.
    End loop.
    The above syntax will help you to close the issue.
    Rgds,
    SR

  • Print out streaked even after the 3 steps cleansing of printhead

    Hi,
    I keep on doing the 3 steps printheads cleansing since the print out remains streaked or the red is missing.
    What if anything can be done before taking to 'a repair' and after the 3 steps printheads cleansing??
    Thanks for help
    Goradana

    Please read this post then provide some details.  What printer model? What operating system?
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Why does Photoshop Elements 10 print dark and red, and not match the computer screen?

    I switched from Photoshop Elements 7 to Photoshop Elements 10.  I cannot get a print of a photo that matches the screen.  Photos are dark and red.  I cannot edit the photos because I do not know what will print out.   I have switched back to Photoshop 7 and my photos print fine, just as they have been edited.  I have spent hours on the Chat line with Adobe.  They have yet to help me resolve this problem.  Does anyone else have this problem or know what to do?  Adobe sure doesn't. I feel I have wasted money and am afraid to ever upgrade again.

    If you are using Photoshop Elements Editor for printing then make sure you have handled the color management of PSE correctly.
    There are two different scenario available in PSE to handle color management.
    Scenario 1 (When printer manages color). If you're known and familiar to your printer profile, the type of paper you are using and if you have any other customization done for your printer profile then in this case please select Printer Manages Color in Color Handling drop down under color management of PSE.
    To achieve this, follow these following steps.
    1. Launch Print dialog.
    2. Click on "More Options..." button.
    3. Now select Color management.
    4. Here you can see the Color Handling drop down. Please select Printer Manages Color.
    Note:- Use this scenario when you are sure a about your printer profile and settings.
    Scenario 2 (When Photoshop Elements handle color). In case you want PSE to handle all color management then please select Photoshop Elements Manages Color in Color Handling drop down. Then select the same printer profile as Image space.
    Note:- If you are using this option, make sure the color management of your Printer is off.
    Hope this will help you.

  • Trouble printing out correct colours

    Hi all,
    I'm trying to print out a DVD cover that I've made in after effects (I'm not too good on PS). It's a brown leather book. I've loaded it into PS as a jpg and I've tried to print it out to my printer, but it's coming out really red, almost magenta. The darker spots are especially poor.
    The printer si a HP with 6 ink cartyridges. It's not particularly good, but I expected a better result.
    I didn't really understand all the print options in PS, but tried a few. Most look quite similar.
    I'm printing to some Ryman's own, double sided matte photo paper, but I've also tried other paper.
    I also tried a normal photo and it didn't look too bad.
    Is there anything I can do to try to get a better colour representation?
    here's the image I'm trying to print:
    cheers

    Try using the HP paper that the company recommends for the printer. HP tests their paper with their colors to ensure good a match. Also there should be (not sure) a printing option to select the HP drivers to use for printing and not adobe. Also check to see if RGB is selected for printing.

  • How can I print out the file directory?

    Years ago, I could print out a list of files in a folder from the finder window. Is there now a workaround utility to do that? I don't want to use screen shots, as the directory is too long and would require several screen shots.  thx.

    http://hints.macworld.com/article.php?story=20060720174103802
    or
    http://reviews.cnet.com/8301-13727_7-20026446-263.html

  • How can I print out the graph I need only, without the controls and indicators?

    I'm doing some programming in LABVIEW. I need to print out only the graph, without the buttons, controls, indicators. I tried to look for such a function in LABVIEW, but in vain. How can I achieve the result I expect in my programming?

    Hi Fenny,
    you should use the report generation functions to create a report containing your graph image and print it.
    Take a look at the Sample Test Report.vi you find in the report examples of LV.
    Just look at the part of the diagram where it is used Append Control Image to report.vi (in the center of the report functions chain); a graph reference is wired to the Ctrl reference input ( to create a reference of your graph right click on it and select create reference).
    Let me know if you need more help,
    Alberto

  • How can I print out the contents of my hardrive

    I have a hardrive with about 200 video clips and need to print the titles for cross refrerencing. I was just going to "grab" screenshots but this will take about ten sheets of paper. How can I print out a list of all the files on the drive?

    I tried this Finder drag method & discovered that it is very important to set the blank TextEdit document to plain text before the drag (from the format menu or with Cmd-shift-t). If you don't, TextEdit attempts to load the content of the files!
    Once I discovered this, I tried the method with Find (Cmd-F) results & it works for that, too. This means that by choosing the right combination of search location(s) & search criteria, you can extend the method to filter the list to just about any files you want, which could be very handy.
    For instance, set the "Kind" criteria to "QuickTime Movie" & location to "Computer" & you get a list of every QT movie. Or set the search location to the folder containing the movies of interest & you get all of them, including ones in subfolders. You could also use the 'date created' or other search criteria to filter the list to a specific subset of movies (or whatever).
    If you need to do this often, you could create one or more 'Smart Folders' with the criteria preloaded for each search.
    The only drawback I see for either Finder based method is the full path one. If you are getting results from just one or a few folders, Find & Replace can delete any of the path name fairly easily, but it becomes a chore if there are a lot of different ones. Some other text editor, like TexEdit Pro, that supports grep searches would be handy here, but since I'm not up to speed on grep, someone else will have to explain how to use it for this, if they want.

  • How can i print out the waveform chart?

      hello everybody,
    how can i print out the "waveform chart". can i do it just push the button. ( example; stop button is stop the program etc..)
    i checked the NI examples but i can't understand. i'm new to the Labview.
    pls help me.
    i added the my program
    look forward your reply
    regards from turkey...
    Message Edited by hknmkt on 05-29-2008 04:15 AM
    Attachments:
    29.05.2008_11.vi ‏37 KB

        hi jim,
    i tried the program but it's not running. When i run the program, it's print out without run the program
    i added the printed file.
    look forward your reply
    hakan
    Attachments:
    error8.JPG ‏8 KB

Maybe you are looking for