Hot to configure sanity-checks ?

Hi All
I went through the support files  and found such kind of log messages during peak hours as below,
2010-07-11 11:55:47 | INFO  | CPU #000 | Started filtering packets of type 'TCP Non-SYN' received on interface # 0. Reason: Started filtering due to attack detection
2010-07-11 12:00:35 | INFO  | CPU #000 | Started filtering packets of type 'TCP No-SYN + RST' received on interface # 0. Reason: Started filtering due to attack detection
2010-07-11 13:07:25 | INFO  | CPU #000 | Stopped filtering packets of type 'TCP No-SYN + RST' received on interface # 0. Reason: Stopped filtering for an administrative pause
Basically those logs mean that SCE detect attacks and then in order to protect itself, it put those attack traffic in filter, one hour later, SCE remove the flows from filter and check again, if attack persist, SCE put attack traffic in filter again.
Could we decrease the time for filtering traffic ? like 10 minutes ?

Hello,
I believe this is what you're looking for:
SCE8000#>configure
SCE8000(config)#>interface LineCard 0
SCE8000(config if)#>sanity-checks attack-filter times filtering-cycle max-attack-time
SCE8000#>show interface LineCard 0 sanity-checks attack-filter times
Filtering cycle: 3600 seconds.
Max attack time: 86400 seconds.
Hope that helps,
Best regards.

Similar Messages

  • Bailout: failed spill-split-recycle sanity check

    hi all
    i hope someone can help me!
    we have an enterprise portals productive installation on aix5.3
    it is based on netweaver 7.0
    i have just installed a java dialog instance on a windows 2003 server 64 bit which is happily talking to the central instance on aix BUT after changing the java parameters (sapnote 723909) for this new instance, the local windows dev_server0 file now complains with the following error:
    JHVM_BuildArgumentList: main method arguments of node server0
    210       com.sap.engine.core.configuration.impl.addons.PropertyName::init (154 bytes)
    211  !    com.sap.engine.core.configuration.impl.cache.CachedConfiguration::prepareRead (167 bytes)
    212       java.util.AbstractCollection::toArray (68 bytes)
    213       com.sap.engine.lib.xml.dom.DOMDocHandler1::onCustomEvent (130 bytes)
    214       com.sap.engine.lib.xml.dom.DOMDocHandler1::charData (73 bytes)
    Bailout: failed spill-split-recycle sanity check
    211   COMPILE FAILED
    (there are many lines but i have just included one occurrence)
    i just wondered if anyone could tell me which java parameter could have caused this?
    i appreciate i could take out each parameter one by one and stop/start the instance to see when it stops complaining (and i will do this if no-one can help me)
    many thanks
    kirsty

    ok,
    i guess it was obvious really.....
    the flag: -XX:+PrintCompilation (which excludes certain classes from compiling in order to prevent possible server VM crashes) is recommended in note 723909 to help avoid crashes caused by certain classes.
    the thing is this flag seems to cause the class to fail a sanity check in order to stop it compiling which then writes out to the server log causing me unnecessary anguish.
    if the flag is there to prevent classes compiling it should do it cleanly and quietly so im not sure now whether i want it or not!!!
    anyway, apologies for anyone's time i wasted
    kirsty

  • Xnee-2.00 Installation - /lib/cpp fails sanity check

    When I first tried running the configure file to start the installation process for this application, I ran into error after error and found solutions to them by installing packages off the SunOS cd's or from the sunfreeware site. But I cant find a solution to this problem.
    the output when running the configure script is as follows for the problem:
    checking how to run the C preprocessor... /lib/cpp
    configure: error: C preprocessor "/lib/cpp" fails sanity check
    the config.log file is very long and full of compile errors...many are repeats and around the part where its failing the only problem i can see is a "conftest.c" line 14: Cant find include file assert.h....
    what are the packages i need for cpp to function, i have gcc-3.3.2 installed, are there others?? is there something else i'm going to run into later?? any help will be greatly appreciated

    Have you try to use pkg-get
    to get the binary from Sun?
    If you really need to compile it by yourself, get studio first to make it easier. It will install developer package library in the box and help to resolve your dependence problem.

  • Glibc 2.19 & find: sanity check of the fnmatch() library function fail

    Since yesterdays update to glibc 2.19, find doesn't like searches by name. The update threw a hole lot of segmentations faults
    [2014-02-12 15:06] [PACMAN] Running 'pacman --color auto -Sy'
    [2014-02-12 15:06] [PACMAN] synchronizing package lists
    [2014-02-12 15:07] [PACMAN] Running 'pacman --color auto -S -u'
    [2014-02-12 15:07] [PACMAN] starting full system upgrade
    [2014-02-12 15:08] [PACMAN] upgraded apr-util (1.5.3-1 -> 1.5.3-2)
    [2014-02-12 15:08] [PACMAN] upgraded linux-api-headers (3.12.4-1 -> 3.13.2-1)
    [2014-02-12 15:08] [ALPM] warning: /etc/locale.gen installed as /etc/locale.gen.pacnew
    [2014-02-12 15:08] [ALPM-SCRIPTLET] Generating locales...
    [2014-02-12 15:08] [ALPM-SCRIPTLET] de_DE.UTF-8
    [2014-02-12 15:08] [ALPM-SCRIPTLET] en_US.UTF-8
    [2014-02-12 15:08] [ALPM-SCRIPTLET] Generation complete.
    [2014-02-12 15:08] [PACMAN] upgraded glibc (2.18-12 -> 2.19-1)
    [2014-02-12 15:08] [PACMAN] upgraded binutils (2.24-1 -> 2.24-2)
    [2014-02-12 15:08] [PACMAN] upgraded gcc-libs (4.8.2-7 -> 4.8.2-8)
    [2014-02-12 15:08] [PACMAN] upgraded elfutils (0.157-1 -> 0.158-1)
    [2014-02-12 15:08] [PACMAN] upgraded gcc (4.8.2-7 -> 4.8.2-8)
    [2014-02-12 15:08] [PACMAN] upgraded shared-mime-info (1.2-1 -> 1.2-2)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_Zt9oRn/.INSTALL: line 1: 10554 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdelibs (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-mobipocket (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded nepomuk-core (4.12.1-2 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kactivities (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kde-base-artwork (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded oxygen-icons (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_lNExqJ/.INSTALL: line 1: 10562 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-runtime (4.12.1-3 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-lib (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded nepomuk-widgets (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-dolphin (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-konsole (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-plasma (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_jc0NOD/.INSTALL: line 1: 10571 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdepim-runtime (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM] warning: /usr/share/config/kdm/kdmrc installed as /usr/share/config/kdm/kdmrc.pacnew
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_9emqkf/.INSTALL: line 10: 10582 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdebase-workspace (4.11.6-1 -> 4.11.6-2)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_HVYliW/.INSTALL: line 1: 10587 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded libkipi (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_JMyH2D/.INSTALL: line 1: 10591 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-gwenview (4.12.1-2 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_BOmkIm/.INSTALL: line 1: 10595 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-kcolorchooser (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_V9lYA5/.INSTALL: line 1: 10598 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-ksnapshot (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded libkexiv2 (4.12.1-2 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_NKbRqP/.INSTALL: line 1: 10602 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-okular (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_1CccYz/.INSTALL: line 1: 10606 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded libkdcraw (4.12.1-2 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdegraphics-thumbnailers (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdemultimedia-ffmpegthumbs (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_PRYdSk/.INSTALL: line 1: 10609 Segmentation fault (core dumped) xdg-icon-resource forceupdate --theme hicolor &>/dev/null
    [2014-02-12 15:08] [PACMAN] upgraded kdemultimedia-kmix (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdemultimedia-mplayerthumbs (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdepimlibs (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded kdeutils-ark (4.12.1-1 -> 4.12.2-1)
    [2014-02-12 15:08] [PACMAN] upgraded lib32-elfutils (0.157-1 -> 0.158-1)
    [2014-02-12 15:08] [PACMAN] upgraded lib32-glibc (2.18-12 -> 2.19-1)
    [2014-02-12 15:08] [PACMAN] upgraded lib32-gcc-libs (4.8.2-7 -> 4.8.2-8)
    [2014-02-12 15:08] [PACMAN] upgraded libsasl (2.1.26-6 -> 2.1.26-7)
    [2014-02-12 15:08] [PACMAN] upgraded mpd (0.18.7-1 -> 0.18.8-1)
    [2014-02-12 15:08] [PACMAN] upgraded nginx (1.4.4-2 -> 1.4.5-1)
    [2014-02-12 15:08] [PACMAN] upgraded openjpeg (1.5.1-1 -> 1.5.1-2)
    [2014-02-12 15:08] [PACMAN] upgraded pam (1.1.8-2 -> 1.1.8-3)
    [2014-02-12 15:08] [PACMAN] upgraded python2-numpy (1.8.0-1 -> 1.8.0-2)
    [2014-02-12 15:08] [PACMAN] upgraded redland (1:1.0.17-1 -> 1:1.0.17-2)
    [2014-02-12 15:08] [PACMAN] upgraded s-nail (14.5.2-3 -> 14.5.2-4)
    [2014-02-12 15:08] [PACMAN] upgraded sudo (1.8.9.p4-1 -> 1.8.9.p5-1)
    [2014-02-12 15:08] [PACMAN] upgraded systemd (208-10 -> 208-11)
    [2014-02-12 15:08] [PACMAN] upgraded systemd-sysvcompat (208-10 -> 208-11)
    [2014-02-12 15:08] [ALPM-SCRIPTLET] /tmp/alpm_7YRIvT/.INSTALL: line 10: 10659 Segmentation fault (core dumped) mkfontdir usr/share/fonts/local
    [2014-02-12 15:08] [PACMAN] upgraded terminus-font (4.38-3 -> 4.38-4)
    [2014-02-12 15:08] [PACMAN] upgraded vim-systemd (20130410-1 -> 20140209-1)
    [2014-02-12 15:08] [PACMAN] upgraded whois (5.1.0-1 -> 5.1.1-1)
    [2014-02-12 15:08] [PACMAN] upgraded xdg-utils (1.1.0.git20140109-1 -> 1.1.0.git20140207-1)
    [2014-02-12 15:08] [PACMAN] upgraded xf86-video-intel (2.99.909-2 -> 2.99.910-1)
    After that nearly all applications segfaulted but somehow it everything works again. Except for find (which I only recognized after mkinitcpio destroyed my initramfs......):
    # find -name \*.pkg.tar.xz
    find: sanity check of the fnmatch() library function failed.
    Regex, type and all other operators work as expected:
    # find -regex '.*\.pkg\.tar\.xz'
    ./gcc-4.8.2-7-x86_64.pkg.tar.xz
    ./binutils-2.24-1-x86_64.pkg.tar.xz
    ./glibc-2.18-12-x86_64.pkg.tar.xz
    ./gcc-libs-4.8.2-7-x86_64.pkg.tar.xz
    # find -type d
    # pacman -Q findutils glibc
    findutils 4.4.2-5
    glibc 2.19-1
    First is suspected it to be a locale issue, but everything seems to be fine:
    # diff -u0 {,/}etc/locale.gen
    --- etc/locale.gen 2014-02-07 23:56:45.000000000 +0100
    +++ /etc/locale.gen 2014-02-12 19:43:03.037279970 +0100
    @@ -124 +124 @@
    -#de_DE.UTF-8 UTF-8
    +de_DE.UTF-8 UTF-8
    @@ -161 +161 @@
    -#en_US.UTF-8 UTF-8
    +en_US.UTF-8 UTF-8
    # locale-gen
    Generating locales...
    de_DE.UTF-8
    en_US.UTF-8
    Generation complete.
    Downgrading to glibc 2.18-12 solved the problem for now...
    # pacman -U --noprogressbar --noconfirm *
    loading packages...
    warning: downgrading package binutils (2.24-2 => 2.24-1)
    warning: downgrading package gcc (4.8.2-8 => 4.8.2-7)
    warning: downgrading package gcc-libs (4.8.2-8 => 4.8.2-7)
    warning: downgrading package glibc (2.19-1 => 2.18-12)
    resolving dependencies...
    looking for inter-conflicts...
    Packages (4): binutils-2.24-1 gcc-4.8.2-7 gcc-libs-4.8.2-7 glibc-2.18-12
    Total Installed Size: 134.89 MiB
    Net Upgrade Size: -0.42 MiB
    :: Proceed with installation? [Y/n]
    checking keyring...
    checking package integrity...
    loading package files...
    checking for file conflicts...
    checking available disk space...
    downgrading glibc...
    warning: /etc/locale.gen installed as /etc/locale.gen.pacnew
    downgrading binutils...
    downgrading gcc-libs...
    downgrading gcc...
    # find -name \*.pkg.tar.xz
    ./gcc-4.8.2-7-x86_64.pkg.tar.xz
    ./binutils-2.24-1-x86_64.pkg.tar.xz
    ./glibc-2.18-12-x86_64.pkg.tar.xz
    ./gcc-libs-4.8.2-7-x86_64.pkg.tar.xz
    According to the findutils manual one should file a bug report for this message, but I don't think they expect glibc to be the buggy implementation of fnmatch that looks enough like the GNU version to fool configure, but which doesn't work properly.
    Does anybody experience similar problems? Does anybody have suggestions how to solve this?
    Last edited by auti (2014-02-13 22:14:12)

    I've regenerated the locales multiple times but only the upgrade to findutils 4.5.12 worked.
    glibc 2.19-2 works with the current findutils.
    But if a corrupt locale archive file caused this, why didn't findutils 4.5.12 complained about this?
    Anyhow: It works, I'm happy; thanks for your effort, Allan!

  • MPLS Sanity-check

    Hi,
    I need someone to do a sanity check on a MPLS design.
    I doing some consulting in a expanding metronet, in Sweden.
    I've got the need to run ethernet over ATM, so I'm thinking EoMPLS. So my query, is it possible to run EoMPLS over the following
    configuration. If so, can I also runs q-in-q (if I reconfigure the MTU size on both sides).
    1Q-TRUNK - 7200VXR - ATM-SWITCH (NON-MPLS) - ATM-SWITCH (NON-MPLS) - 7200VXR - 1Q-TRUNK
    Thanks
    Best regards
    Daniel

    It is certainly possible to run MPLS (frame mode) on the interface/subinterface between the two 7200s, which will allow you to run EoMPLS. You should also be able to configure q-in-q in this configuration.
    Hope this helps,

  • OES2SP3 to OES11SP1 Sanity Check

    I have an OES2SP3 (SLES10SP4) server that I want to move to OES11SP1 (SLES11SP2). The tree is stable, but I am having some issues with the OES2SP3 server that I don't want to spend the time troubleshooting. My Master replica and all services is on a NW65 server and I have the luxury of being able to wipe the OES2 server. The OES2 server only does some file backups via scripts to an internal RAID and holds a RW replica. Looking for a sanity check on my process...
    1. copy scripts from server to backup
    2. remove eDir from server using nds-uninstall
    (the OES doc says that ndsconfig rm is not supported in OES2SP3)
    3. wait for replica ring to be stable - monitor via dsrepair on NW65 server
    4. remove any references to the OES2 server via ConsoleOne
    5. wait for replica ring to be stable - monitor via dsrepair on NW65 server
    6. fresh install of SLES11SP2 and OES11SP1 (eDir only) onto server
    7. add other OES11 services to server
    TIA
    -L

    Originally Posted by LarryResch
    I have an OES2SP3 (SLES10SP4) server that I want to move to OES11SP1 (SLES11SP2). The tree is stable, but I am having some issues with the OES2SP3 server that I don't want to spend the time troubleshooting. My Master replica and all services is on a NW65 server and I have the luxury of being able to wipe the OES2 server. The OES2 server only does some file backups via scripts to an internal RAID and holds a RW replica. Looking for a sanity check on my process...
    1. copy scripts from server to backup
    2. remove eDir from server using nds-uninstall
    (the OES doc says that ndsconfig rm is not supported in OES2SP3)
    3. wait for replica ring to be stable - monitor via dsrepair on NW65 server
    4. remove any references to the OES2 server via ConsoleOne
    5. wait for replica ring to be stable - monitor via dsrepair on NW65 server
    6. fresh install of SLES11SP2 and OES11SP1 (eDir only) onto server
    7. add other OES11 services to server
    TIA
    -L
    Hi Larry,
    If this is a regular fileserver (not housing iFolder and such special services)... your steps seem to cover the bases.
    As an extra preparation step, if the OES server has it's own eDir replica, I'd remove it at least an hour or so before moving on to removing the OES server from the tree. Also running a quick eDir health check after having done so and before moving on to remove the server is a good routine.
    Out of curiosity, do you have a link to the docs specifying 'ndsconfig rm' is unsupported? Have not run into issues with it but also had not seen that reference in the docs (not that I read them daily :P ).
    If you have NSS volumes, you can relink them to the new server using the update NDS option within nssmu. Do note that you will also have to relink object properties to the volumes (like the user home directories).
    Your tree CA configuration is also still valid (and not housed on the OES2 server)?
    Cheers,
    Willem

  • P6N Diamond & SLI controller sanity check

    what i would like is a sanity check please from community before RMA is done, i've already contacted both MSI and supplier and have RMA status enabled but before shipping would like to do an opinion from more professional/ experienced people here please 
    MSI reports that SLI controller is bad and to RMA... so ya i probably will but just want doctor 2nd opinions
    thanks in advance!
    testing past few days and having major problems with SLI. 
    mainboard: P6N Diamond MS-7320 v1.0 BIOS 1.2
    processor: Intel Core2 Duo E6850
    graphics cards:  SLI  NX8500GT TD256EH (x2) PCIx16 (both in white slots )
    memory: Corsair CM2x 1024-66400C4 (800mhz, dual channel) (total 2GB)
    drives:  WD1600AA (?) SATAII 3.0GB (raid 0, hardware dipswitched)
    power:  rosewill RX750-S-B Xtreme 750W ATX12V v2.2 EPS12V v2.91  (voltages per bios in spec)
    I have performed several tests including:
    memtest86+ : 25 iterations on memory over 8 hour period = PASS
    ntune stability test : nx8500GT (card #1) in pcix16slot#1 = PASS
    ntune stability test : nx8500GT (card #1) in pcix16slot#2 = PASS
    ntune stability test : nx8500GT (card #2) in pcix16slot#1 = PASS
    ntune stability test : nx8500GT (card #2) in pcix16slot#2 = PASS
    ntune stability test : card#1 in slot#1 & card#2 in slot#2 = FAIL (sli mode on)
    ntune stability test : card#1 in slot#1 & card#2 in slot#2 = FAIL (sli mode off)
    ntune stability test : card#1 in slot#2 & card#2 in slot#1 = FAIL (sli mode on)
    ntune stability test : card#1 in slot#2 & card#2 in slot#1 = FAIL (sli mode off)
    no overclocking
    CPU temperatures ~22 celcius
    SYSTEM temperatures ~38 celcius
    GPU1&2 temp idle ~63 to 66 celcius
    GPU1&2 temp stress ~72 celcius
    all hardware tests ok, no power surges, power supply is adequate and in specs.
    only problems occuring when both cards are in system and operate in either SLI or non-SLI mode.
    all microsoft latest security updates applied
    following hotfixes applied:
    KB940105
    KB936710
    KB930833
    KB932471
    KB945149 (latest per request)

    Quote from: BOSSKILLER on 07-December-07, 04:33:29
    What kind of problems you have?
    Have you tested in XP?
    PSU details.
    Latest drivers from Nvidia installed?
    Power cables to both VGA's connected?
    SLI Bridge connected?
    Hi,
    Answers best I can below:
    Q: Have you tested in XP?
    No, sorry.. I only have Vista x64 platform to use and test (license only  )
    Q: PSU details.
    posted above, but here you go...
    Rosewill RX750-S-B Xtreme 750W ATX12V v2.2 EPS12V v2.91  (voltages per bios in spec)
    Q: Latest drivers from Nvidia installed?
    Yes (data from dxdiag for you)
    Driver Version: 7.15.0011.6375 (English)
    DDI Version: 9Ex
    Driver Attributes: Final Retail
    Driver Date/Size: 10/4/2007 17:14:00, 4993024 bytes
    WHQL Logo'd: Yes
    Q: Power cables to both VGA's connected?  &  SLI Bridge connected?
    Interesting point   With this particular setup, these MSI NX8500GT TD256EH cards do not have SLI bridge and do not require power plugged into video card.  SLI option has onboard bridge controller and is recognized by nvidia drivers and nTune control panel (i am actually able to enable SLI this way w/o a bridge)  yes, I had to rub my eyes too a few time while researching this configuration.
    Mainboard supports ATX 24pin powerconnector (ATX1) and a ATX 12V (JPW1) 8 pin connector.  The power supply supports these types of connections to mainboard.  I will need to reboot after this post and do a visual inspection of reported BIOS voltages for you though and will do so.

  • Managed system configuration, step:Check Prerequisites

    hi firends,
    We've updated our SLM system up to SP13 and import finished success.
    When we starts managed system conf from menu SOLMAN_SETUP - Managed System Configuration - Configure System - Check Prerequisites, execution return error that system prerequisites are not fullfilled.
    But from menu Status all SP's are correct
    Additionally screenshot added to attachment
    please help me to resolve this problem.
    P.S. all other steps in Managed system conf wizard finished Success.
    Thanks in advance
    Shahin

    Hi Matthias,
    Please review SAP Note 1571442 as it might be helpful in resolving this error message.

  • Configure:3955: checking for C compiler default output file name

    Hi,
    I am trying to configure oracle bsd on AIX and got the below error,
    # sh /ldap/db-4.6.21.NC/dist/configure
    checking build system type... powerpc-ibm-aix5.3.0.0
    checking host system type... powerpc-ibm-aix5.3.0.0
    checking if building in the top-level or dist directories... no
    checking if --disable-cryptography option specified... no
    checking if --disable-hash option specified... no
    checking if --disable-mutexsupport option specified... no
    checking if --disable-queue option specified... no
    checking if --disable-replication option specified... no
    checking if --disable-statistics option specified... no
    checking if --disable-verify option specified... no
    checking if --enable-compat185 option specified... no
    checking if --enable-cxx option specified... no
    checking if --enable-debug option specified... no
    checking if --enable-debug_rop option specified... no
    checking if --enable-debug_wop option specified... no
    checking if --enable-diagnostic option specified... no
    checking if --enable-dump185 option specified... no
    checking if --enable-java option specified... no
    checking if --enable-mingw option specified... no
    checking if --enable-fine_grained_lock_manager option specified... no
    checking if --enable-o_direct option specified... no
    checking if --enable-posixmutexes option specified... no
    checking if --enable-pthread_api option specified... no
    checking if --enable-rpc option specified... no
    checking if --enable-smallbuild option specified... no
    checking if --enable-tcl option specified... no
    checking if --enable-test option specified... no
    checking if --enable-uimutexes option specified... no
    checking if --enable-umrw option specified... no
    checking if --with-mutex=MUTEX option specified... no
    checking if --with-tcl=DIR option specified... no
    checking if --with-uniquename=NAME option specified... no
    checking for chmod... chmod
    checking for cp... cp
    checking for ln... ln
    checking for mkdir... mkdir
    checking for rm... rm
    checking for sh... /usr/bin/sh
    checking for a BSD-compatible install... /ldap/db-4.6.21.NC/dist/install-sh -c
    checking for C compiler default output file name...
    configure: error: C compiler cannot create executables
    See `config.log' for more details.
    and in config.log,
    configure:3955: checking for C compiler default output file name
    configure:3982: xlc_r -O2 -D_THREAD_SAFE -Wl,-brtl conftest.c >&5
    /ldap/db-4.6.21.NC/dist/configure[3983]: xlc_r: not found
    configure:3985: $? = 127
    configure:4023: result:
    configure: failed program was:
    | /* confdefs.h. */
    | #define PACKAGE_NAME "Berkeley DB"
    | #define PACKAGE_TARNAME "db-4.6.21"
    | #define PACKAGE_VERSION "4.6.21"
    | #define PACKAGE_STRING "Berkeley DB 4.6.21"
    | #define PACKAGE_BUGREPORT "Oracle Technology Network Berkeley DB forum"
    | #define HAVE_UPGRADE_SUPPORT 1
    | /* end confdefs.h. */
    |
    Is this beacase valid c compiler not existing?
    # which cc
    which: 0652-141 There is no cc in /usr/bin /etc /usr/sbin /usr/ucb /usr/bin/X11 /sbin /usr/java14/jre/bin /usr/java14/bin.
    # ksh: which:: not found.
    # which c
    which: 0652-141 There is no c in /usr/bin /etc /usr/sbin /usr/ucb /usr/bin/X11 /sbin /usr/java14/jre/bin /usr/java14/bin.
    Thanks,
    Message was edited by:
    GK Joe

    Joe,
    I presume you are trying to build Oracle BDB and not bsd as you have mentioned.
    Yes, the error message you are getting is for not having the CC compiler in your system or the path isn't set. Check in the /usr/vac/bin directory if you have one in your system. You might find both xlc and cc compiler there. Set this directory to your path so that 'configure' can see it.
    Regards,
    -Debsubhra

  • How to configure ATP check for "create standard order in SD (OR type)"

    first, I had check my stock, I only have ten PC
    , but when I enter 100 PC in a OR order, and issue ATP check, it is carries out, why? I had set availavility check into 02 in MRP3 view

    Availability check
    1. Availability check is an integral part of the business process that determines if the required delivery quantity can be met on a required delivery date. For this purpose the system takes into account pre-delivery activities such as scheduling for picking or packing times and the time taken to produce or obtain the material. It also performs several background functions such as Backorder processing, rescheduling and ATP quantities.
    2. Backorder processing: processing of a sales order that has not been fully confirmed or not confirmed at a certain delivery date.
    3. Rescheduling: is a proposal of how u2013 confirmed quantities already assigned to a sales order can be reassigned to other sales orders that have a higher priority.
    4. Available to promise (ATP): is a process of checking the available quantities of a material. The ATP quantity consists of warehouse stock + planned receipts (incoming stock) u2013 planned issues (outgoing stock). to examine stock on hand (CO09) proceed to logistics u2013 sales & distribution u2013 sales u2013 environment u2013 availability overview.
    5. Replenishment lead time (RLT): is the time taken for the material to become available either internally (in house production) or externally (from a vendor). The most important things to consider during an external procurement are purchasing and MRP2 (procurement) views of MMR where the processing time for purchasing, planned delivery time and goods receipt processing time are taken into account. On the other hand internal procurement is based on in house production time (MRP 2 view) goods receipt processing time or alternatively RLT time, which is found on MRP 3 view.
    6. RLT (Replenishment Lead Time) is the time taken for the material to become available. RLT is only used when doing an ATP check (Available To Promise). The value of RLT for a material is specified on material master record.
    7. There are three types of availability checks u2013
    Check on basis of ATP quantities.
    Check against product allocation.
    Check against planning.
    Configuring Availability check through Checking Groups
    1. The checking group + checking rule determine how the availability check is to be performed.
    2. The checking group determines whether and how the system checks the stock availability and generates requirements for material planning. The checking group defines what type of requirements will be passed on i.e. summarized requirements (daily/weekly) or individual requirements for each sales order.
    3. The checking rule applies to how the availability check is to be carried out at the transaction level. Note that you must define checking rules for each individual application such as for production orders for example. In Sales and Distribution, the checking rule is specified internally within the system and cannot be changed.
    4. The checking rule, in conjunction with the checking group, determines the scope of the availability check for every business operation; that is, which stocks, receipts and issues are to be included in the availability check and whether the check is to be carried out with or without the replenishment lead time.
    5. Briefly explaining the above u2013 checking group determines which type of requirement to be passed on to MRP whether it be individual or summarized and checking rule which is at the transaction level and can be configured independently for each application module, determines which stocks, receipts and issues to be taken into account. For performing an availability check checking group has to work in conjunction with checking rule.
    6. Advantages of individual processing over summarized processing u2013
    Backorder processing is possible.
    You can access (MD04) order, line and schedule line individually which gives a greater control on available stock and requirements placed on stock.
    The system automatically uses individual requirements in case of special stock items.
    7. Required data for the Availability check to be carried out u2013
    The Availability check must be switched on at the requirement class level.
    The Availability check must be set at the schedule line level.
    A requirements type must exist by which the requirements class can be found.
    A plant must be defined in the sales order for each schedule line item (in other words plant must be defined for every material in MMR).
    A checking group must be defined in the material master record in the MRP3 screen in the availability check field.
    8. Configuring Availability check and defining Checking Groups u2013
    Checking groups are introduced into the sales order based on the setting in the material master record.
    SAP standard checking groups are 01 u2013 summarized requirements and 02 u2013 individual requirements or you can create your own by copying the standard ones.
    Total sales and total deliveries columns are there to configure a checking rule to sum up requirements to post to MRP either individually or by day or week.
    Block quantity required can be set if you want several users to be able to process the material simultaneously in different transactions without blocking each other.
    The no check indicator is CHECKED when you DO NOT want the system to carry out ATP check.
    9. Defining material block for other users u2013 the block check box is an indicator that enables you to block material master records of a particular material during the availability check and restrict other users from accessing same master record and reserve the material. If the block is not set, two users can confirm the same material at the same time for two different orders, not knowing if the stock is available or not. If you select this field, the material is blocked during the availability check and other users cannot: a) Make changes in the material master record. b) Create purchase orders for the material. C) Create orders for the material.
    10. Defining default values for checking groups - Checking groups are introduced into the sales order based on the setting in the material master record.
    However if there is no entry present in the material master record for the checking group, a default value can be set here, depending on material type and plant.
    This default value will be used by the system depending on the material type mentioned in MMR and plant in sales order.
    If an entry exists, this default value is over written by MMR.
    11. Controlling Availability Check u2013 in this section, you tell the system what stock on hand and what inward and outward movements of stock it must take into account when performing the availability check in addition to whether or not to consider the replenishment lead time.
    12. These settings are based on the checking group that is assigned to the material master record and the checking rule that is predefined and assigned to the sales and distribution transaction.
    13. These settings carry out control both for sales order and delivery as well. This is due to the fact that you may want to include specific stock or incoming stock for the sales order, yet at the time of the delivery only include physical stock on hand waiting to be shipped.
    14. It is possible to indicate to the system that you would like the availability check NOT TO CHECK the stock at the storage location level. This indicator is used to set the scope of the availability check.
    15. It is used to switch off the check at storage location level. You create a reservation for a particular storage location. However, the scope of the availability check is set in such a way as to exclude the storage location. In this case, the system carries out the check at plant level only and does not take the storage location into account that is specified in the reservation.
    16. Should you not want the system to automatically check RLT, you may indicate so here. RLT is the time taken for a material to become available. It is only used when doing an ATP check and is taken from MMR.
    17. defining the elements in the availability check entirely depends on the business needs, but a few tips are given under u2013
    When controlling the Availability check at the time of the sales order, a purchase requisition does not necessarily indicate by it is going to come into the plant.
    A shipping notification on the other hand - a confirmed purchase order u2013 is a good indicator of receiving stock on a specified date.
    It is always recommended not to select the shipping notifications for the delivery requirements type as you may not actually receive the stock into plant or warehouse for which you are creating a delivery.

  • Steps in configuring availability check for STO Prs

    I want to configure Availability check for stock transport PRS.
    what are the steps.

    Hi,
    please check the transaction code OMGR.(Sprommpurchasingpurchase requisitionset up stock transport requisition.
    Regards,

  • Need info on BW system sanity check

    Hi ,
    I am new to this Area,
    can any one tell me what is the BMW system sanity check?
    when we need to do this check?
    on what BW system we need to do this?
    Is there any pre defined steps we need to follow on sanity check?
    Is there any check list available for sanity check?
    Points will be assigned for your feed back.

    Hi Lakshmi,
    Go to transaction code RSRV and see the test available there.
    Also read documentation available for each test , it is self explainatory.
    hope it helps
    Regards
    Vikash

  • Curve 9380 gets warm/hot after configuring the email accounts

    Hello,
    I am facing this problem, need your help or the solutions.
    My Curve 9380 gets warm/hot after configuring the email accounts. It drains the battery in a hour. If I remove all the email accounts then its working normal.
    Are anyone facing such issue. Please help.
    Regards,
    Sameer

    i have not activated my email accounts even though my phone was getting the same problem that it gets warm and battery gets ruined quickly..plzz help me in that..

  • Db sanity check

    Hi All,
    I would like to develop sanity check script for our product Oracle Db.
    It should be put on crontab, worked periodically.
    How can I retrieve simple pl/sql query(for example how many connections and user..) elapsed time?. Is it possible to achieve this goal by using UNIX scripts(perl, bash etc..) and specific pl/sql statement or have I write to application with java or C?

    Bash and Sql can be used for that, but you should clarify a bit more what you want to do. Here a small example :
    $ cat users.sql
    col username for a20
    select sid, serial#, username, to_char(logon_time,'dd/mm/yyyy hh24:mi:ss') logon_time,
            to_number(sysdate - logon_time)*1440 elapsed_minutes
    from v$session
    where username is not null
    order by username, logon_time
    exit
    $ sqlplus -s / as sysdba @users
           SID    SERIAL# USERNAME             LOGON_TIME          ELAPSED_MINUTES
           144         38 SCOTT                02/04/2006 15:18:10      21.6666667
           142         14 SCOTT                02/04/2006 15:28:41           11.15
           143        105 SYS                  02/04/2006 15:39:50               0
           159        113 TEST                 02/04/2006 15:18:43      21.1166667
    $                                                                                                                        

  • Sanity check - migrating library to new mac

    I'm migrating to a new machine and will use the opportunity to do a fresh install of Aperture. I'd be grateful for a reminder / sanity check on how to migrate my data / settings after the install:
    All I need to do (after Aperture is installed, updated and checked) is replace the default library file with my Aperture library from my previous machine and start Aperture ?
    My library includes both local and referenced (to a network drive) masters. Am I likely to need to re-establish connection with all of the referenced masters ?
    What about keywords and other preferences ? Can someone remind me where these live and what needs to be moved ?
    Many thanks.
    Paul

    macpaul11 wrote:
    I'm migrating to a new machine and will use the opportunity to do a fresh install of Aperture.
    Yes, it is important to do a fresh install of all apps rather than "migrate" apps. Repair Permissions immediately before and immediately after each installation.
    All I need to do (after Aperture is installed, updated and checked) is replace the default library file with my Aperture library from my previous machine and start Aperture ?
    Correct.
    My library includes both local and referenced (to a network drive) masters. Am I likely to need to re-establish connection with all of the referenced masters ?
    No, Aperture should handle that.
    What about keywords and other preferences ? Can someone remind me where these live and what needs to be moved ?
    Again, Aperture should handle that.
    Good luck!
    -Allen Wicks

Maybe you are looking for