How best to interface an airport extreme with a NAS?

I would like to do the following:
1) Access my NAS over my Wi-Fi network using my Airport Express running on the 5 GHz channel, locally, to access files. For back-up I have been connecting the NAS directly to the MBP with an Ethernet cable to get better throughput. How much worse would this be wirelessly. In other words, would incremental back-ups be doable over Wi-Fi, or would this be pitifully slow?
2) Access my NAS remotely over my Wi-Fi network using Airport Express. The NAS has its own IP address, a ReadyNAS NV+.
If #2 is not possible, how would I do this using an Apple Extreme Base Station?
Finally, I am using a new MBP running 10.9.1 and notice that the Airport Utility is really dumbed-down compared with the utility that I was using on 10.6.8, which is sad. So, how can I see the router's performance as I was able to see previously ex. clients, real-time graph of transmission speed per device on network, and signal strengthH
Thank you.

Thanks Tesserax!
for your support..
I changed it the way you told me..
it is very simple... and sounds very logic..
But after I did changed it in the correct IP address of the server
and I changed the IP address of the Internet Router (this was a must concerning the AP utility)
1> the internet was slown down..
2> the server was not reconisable by the iMac.. he gives the server a PC status ?!?!
3> the connection was poor and was not found in the AP network
very strange so I changed it to the old version
is there really no option?
perhaps with the DHCP? or with the Internet router?
FYI
I have:
1: Internet/ connected with a HUAWEI router, recieved from my internet provider
2: connect the Huawei router with the AP Extreme Router
3: connect the AP Extreme router with the Server NAS
4: AP Extreme router is the basis.. and from there I do have an Apple Airport Network

Similar Messages

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

How do I use my airport extreme with my FIOS router?

How do I use my AirPort Extreme base station with my FIOS Router to extend my network? I have hard disks connected to my AirPort Extreme and would lik to access them.

Probably can't answer all your questions - but.... I use a Linksys (wired and wireless) router as my primary entry point for FIOS. I use a Time Capsule and an Airport Express as a common wireless connection. So I have two visibile wireless networks and use them both depending on where I am in the house. Both the TC and AEx can be seen either wirelessly or wired from the entire network. Note - the Linksys provides all the DHCP - you set the apple routers as "bridge mode."

How do i connect my airport extreme with my airport express

how do i link my Airport Express with my Airport Extreme?

Hello Bob -
I have an Apple Extreme (5th Gen) and I have tried to extend my network with an Apple Express Model No. A1264 with the ethernet connection. It does not seem to work, and has crashed my network twice. When I did get it to work, the wireless crawled. When I took the AirPort Express off of the network the speed went back up.
Can this be done to extend the network, as I have the Extreme in the basement where the cable comes into the house, and I have two other floors that need wireless access. Any suggestions for this older model AirPort Express?
Thanks.

How to connect to dsl airport extreme with built in modem

Hello everybody,
while we were tiding our cellar, i found an old airport extreme (a1034) with a built in modem, but i aint able to connect to my isp.
I looked throug the manual, but i didnt got answers there (maybe because of my poor english) . Is there a tutorial out there which tells me
how to connect to my isp?
Regards Floh
PS: again sorry for my poor english

If you try to set up the new AirPort Extreme with AirPort Utility 5.6.1, you will receive a notice that you need a more up to date version of AirPort Utility.
Nevertheless, AP 5.6.1 will allow you to set up the basics....wireless network name, password, etc.
It will appear that you can change other settings that are not found in more recent versions of AirPort Utility, but if you go in and check using a newer version of AirPort Utility, you will find that the settings that you thought you had made have not "stuck".
For example, you want to change the Radio Mode on the new Extreme and not use the Automatic setting. AP 5.6.1 will appear to let you do this. But, if you check the setting using a more recent version of AirPort Utility you will see that the setting is still set at "Automatic".
So, the bottom line here is that unless the newer version of AirPort Utility has the specific setting that you want to change, you will not be able to make that change.
Is there ANY chance, to set up my new "towers" with more
options, than the current Airport Utilities do offer?
Unfortunately, no.

How to replace a older Airport Extreme with a newer model? (OS 10.6 w/ Mac Mimi)

How do I replace a older Airport Extreme with a newer model? (Mac Mini OS 10.6.8 )

There is not much more to it than to buy a new one, and configure it using AirPort Utility.
You should be using AirPort Utility 5.6.1.
Power down your modem before removing your older Extreme and connecting the new one.

How many network interfaces the Airport Extreme (a/b/g/n with USB) has?

I am trying to use an SNMP client on the computer to monitor my network traffic.
I using the Airport Extreme (AEBS) to connect to the internet using PPPoE. wifi and ethernet (RJ45) ports are used for LAN
Now after setting up the SNMP client, it shows so many interfaces the AEBS has, and most names of the interfaces cant give me a clue about what they are:
1: mgi0
2. mgi1
3. mv0
4. mv1
5. lo0
6. wlan0
7. wlan1
8. pppoe0
9. bridge0
The "pppoe0" interface is self evident. That's the overall traffic in and out of the router to the Internet.
But I also want to monitor the traffic on my local computer, which is a Macbook Pro connected thru wifi. I also have a few other windows boxes on the LAN using wifi or ethernet connect.
So I need to what those interfaces are.
Is there any documentation regarding the network interfaces of the AEBS?

Gabriel Dillaine wrote:
Now after setting up the SNMP client, it shows so many interfaces the AEBS has, and most names of the interfaces cant give me a clue about what they are:
This post on another forum will explain some of those:
http://forums.macrumors.com/showthread.php?t=846079

How do I set up Airport Extreme with cable modem and router?

Hi--
I'm having a house built and all of the wiring for TV, phone, and internet will be centralized in a closet. The cable modem can be placed there as well. In one room in the basement I want to use my Airport Extreme for my iMac and USB external hard drives. In another location of the basement, I'd like to set up a Time Capsule for another desktop and USB printer. If the cat5e comes out of the wall at each location, I "think" I need a router at the closet location. I also thought I might need an Airport Express upstairs on first or second floor to boost signal for my laptop. The house isn't that big so maybe that's overkill. So beyond the router question, do I want to set up a roaming network and have the Airport Express connected via ethernet or just wireless if the thought is that I need this? Finally, if I should connect cable modem to router to Airport Extreme, Time Capsule, etc., in what order and ports does the equipment get connected? Many thanks!!

Welcome to the discussions, Forum Girl!
It would be best to position the cable modem and main router in the central location like the closet if possible. The other devices would connect via ethernet to the wall jacks in each room.
If you could setup a "roaming" wireless network as you mention, this will give you better wireless performance and coverage. This is the way commercial establishments like airports, businesses, etc. are configured for wireless.
The order of connection would go something like this: ethernet connection > cable modem >main router>devices. Devices could be computers, routers, a backup device, etc. Since the Extreme has only 3 LAN ports for ethernet connections, you will also need to plan to install an "ethernet switch" near the location of the main router to provide enough ethernet jacks. If you are planning to use DirectTV, etc or your audio/video devices require ethernet connections (most new products do for updates and extra features), be sure to plan for that as well.
Make sure that CAT5e or CAT6 wiring is run so you will be able to take advantage of faster gigabit speeds.
Finally, it would be a good idea to work with an IT specialist to go over your plans to make sure all the bases are covered. This would be money well spent.

How Do I Connect An Airport Extreme With Password to another Wireless Devic

We have a setup for two different wireless devices so that there are multiple locations that can get online, but the entire setup has no passwords assigned. We would like to assign passwords to both wireless devices so that only the appropriate people are getting online. How does one do this?
The first wireless device that connects directly to the modem from the phone company is a brand new Apple Airport Extreme. The computer that set up the device so that people can get a signal was from a PC that is directly connected to the Airport Extreme via an ethernet cable. Also connected to the Airport Extreme is an ethernet cable that goes (50-100ft) to another wireless device - by Netgear - which then sends out another signal to pick up wireless internet, which is the signal/network that I work from.
If we assign a password to the Airport Extreme, I'm guessing it will complete screw up the connection to the Netgear. How would that be dealt with? And, how could we then, if we wanted, set up a password for the Netgear as well. I've read some initial information on the user guide CD and online, but I don't know the terminology of whether these are networks or just wireless devices 'bridged' together, etc.
My biggest concern, is it works right now, but the owner of the devices wants to put passwords on it and I want to make sure we can keep it working even with passwords. Does anyone know how to easily set up passwords and can I do it from my computer even though they were initially set up by a PC? Or do I have to do it from the PC and if so, how, because I am completely a Mac person and am very unfamiliar with Windows. Thanks.

Question that I need to know now is how do we set up a password on the Apple Airport Extreme now, when it is already set up and working without one?
Open AirPort Utility.
Select your base station, and then choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Click AirPort in the toolbar, and then click Wireless.
Choose a password scheme from the Wireless Security pop-up menu.
Enter the password all users will need in order to join this wireless network.
AirPort Utility 5.1 Help: Password-protecting your wireless network
Also, are there different types of passwords and if so, what is the most reliable one so that we don't lose connections, time out or have any other quirks?
There are different types of wireless encryption. WPA2 and WPA are the most secure especially when used with a non-dictionary password. 128 bit WEP is passable in most situations but not very strong. 40/64 bit WEP is extremely weak.
There is really no general "reliability" issue with any of them. Some devices aren't compatible with some of them.
If when we assign a password to the Apple Airport Extreme and for some reason the Netgear stops working, how do we unassign/take away the password on the Airport to get it back to the current setup that we know does work?
Follow the procedure above but disable wireless encryption instead of enabling it.

How do I Set up airport extreme with existing fios wireles network

Hello al, l I have an existing wireless network with an arcitonic wireless router provider with my fios tv. Everything is working well. Now I want to add airport extreme to increase my network range and later add apple tv /net flicks I,m not great with this stuff. Some wold be great.

You will need to establish a permanent Ethernet cable connection from one of the LAN <-> ports on the Fios router to the WAN port (circle of dots icon) on the AirPort Extreme and then configure the AriPort Extreme to "Create a wireless network".
You can configure the AirPort Extreme to provide another separate wireless network if you wish, or if you assign the same wireless network name, and use the same security setting and password that the Fios is using, the Extreme will provide more wireless coverage....and you won't have to change wireless networks to connect to the wireless on the Extreme.
Follow the guided setup using AirPort Utility to "create a wireless network". The setup will suggest that you configure the AirPort Extreme in Bridge Mode, which would be the correct setting when used with the Fios router.

How to set up multiple Airport Extremes with 1 SSID

Equipment:
     Office with 2 floors
     1 Modem
     1 Router
     1 Switch
     5 Airport Extremes (2014 models, each in Bridge mode)
Network layout:
     Modem -> Router -> Switch -> 5 Airport Extremes
Current Setup:
     Each Airport has their own unique SSID (ex. 1st Floor - Conference, 2nd Floor - Content, etc.). Connectivity is fine with this setup, different users join the closest Airport/SSID to them. Only issue is that user needs to switch to different SSID's as they move around the office.
Objective:
     Set each Airport to the same SSID so people don't need to switch to different SSID's as they move around the office.
Problem:
     I attempted to set each Airport to the same SSID. No issues with the setup, everything looks good in Airport Utiltiy. The problem is that some users connect with no issues, but when other users try to connect, they are asked to input a password, which is repeatedly rejected (even though the passwords are set up correctly on all Airport Extremes, and input correctly on all devices).
     I think this has to do with the 50 wireless user limit on the Airport Extremes, it looks like an Airport is maxed out at 50, and when a device tries to connect, it is rejected. I looked for a way to limit the wireless range on each Airport, but no option exists in Airport Utility.

Don't know what kind of main router that you have, but try setting the DHCP Lease Time to 1 hour if it is not already set to that limit.
If it is already set to 1 hour, lower it to the next available setting and update the router.
Then power off the entire network, then power up the main router first, and let it run a few minutes, then start the AirPorts one at a time about a minute apart.

How do you set up airport extreme with a windstream all in one modem with the wireless router built in

I have a wireless network that I want to extend so there will be wifi coverage all over the whole house. I want to use the airport extreme to do so. so far all i can get to work is the airport making another network via a eithernet cable that is pluged into one of the ports on the windstream wireless router/moden (all in one you plug the phone line into this and it has the wireless built in) and the other end is in the WAN port of the airport. I guess the real question is do I need to change any settings on the windstream wireless router/modem to do so. Every time I select all the options to extend a network wirelessly I keep getting errors.

The Airport Extreme can not wirelessly extend a 3rd party router, it can only extend another Apple router. If you can somehow keep the two connected via ethernet, you can setup a roaming network. A roaming network is essentially "extending" your network by using an ethernet cable to bridge the two routers.

Airport Extreme with attached NAS drive

I have Airport Extreme connected by ethernet to my sky broadband router. Am thinking of attaching a NAS drive to AE in order to move itunes library from my MacBook (to free up space). Has anyone done this and any recommendations for which drive to use.

Yes, most NAS's come without a HD.
And yes, you connect the NAS to your Airport Extreme by an ethernet cable. I don't have my iTunes library on the NAS, but I'm pretty sure new music will be put directly on the NAS. Having to move it every time you buy something new is very clumsy and not Apple-like
You can either connect your TV to the Airport Extreme by an ethernet cable, but that may be a difficult option if these are in separate rooms.
You can also connect your TV to your Airport Express. I assume your home theatre is connected to the jack connecter on the Express. Then you can connect your TV with a ethernet cable to the Airport Express. At home, I have my TV connected this way to the Express and can easily stream movies from my QNAP to my TV. In your situation with the iTunes library on the NAS, you can also stream video from iTunes to your TV.
Please make sure that:
1) your TV has an ethernet connector
2) your TV supports media servers (DLNA or UPnP) if you want to stream directly from your NAS (if you are going to stream video from iTunes, this isn't important)

How can I access HDD on Airport Extreme with iPad

How can I access HDD on Airport Extreme with iPad

Without third-party software I don't think you can. An iPad has no user-accessible interface to a file system. Just what is it you're trying to do?

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How best to interface an airport extreme with a NAS?

Similar Messages

Maybe you are looking for