How can i build my own varient data type?

I load dll from roper scientific ccd camera which need varient data type.The following is the example
region.s1=0;region.s2=511;region.p1=0;region.p2=511;region.sbin=1;region.pbin=1;
Please reply as soon as possible
Regards

Mark,
With LabVIEW, you can convert your data to a variant. These functions are located in Functions»Advanced»Data Manipulation»Variant. This will convert LabVIEW's data types to Visual Basic's Variant type.
Randy Hoskin
Applications Engineer
National Instruments
http://www.ni.com/ask

Similar Messages

How can i add formula to waveform data type?

I want to interpolate my acquired data in terms of voltage to temperature. For this i need to use polynomial equation, but i am not able to directly attach formula node to the waveform data type. I want to know how can i add formula node to waveform data, and then also have it real time.

One additional thought that may be helpful. Once you get the Y component of the waveform graph you are going to attempt to wire this into a formula node. You can do one of two things with that array. Put a for loop around the formula node and index the array into and out of the for loop. This allows you to do scalar math on the data. It is also possible to index and array in a formula node. The following KnoledgeBase demonstrates how to do this: http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/9d72b6069346942386256a0d00604ed4?OpenDocument

Need help :: how to search in nested table/varray data type

I have the following structure...
CREATE TYPE lang_con AS VARRAY(15) OF VARCHAR2(50);
CREATE TYPE rel_con AS VARRAY(15) OF VARCHAR2(50);
CREATE TABLE Country_n(
"NAME" VARCHAR2(40 BYTE) CONSTRAINT "COUNTRY_NAME_NOTNULL_N" NOT NULL ENABLE,
"CODE" CHAR(2 BYTE),
"CAPITAL" VARCHAR2(40 BYTE),
"PROVINCE" VARCHAR2(40 BYTE),
"POPULATION" NUMBER,
"AREA" NUMBER,
"LANGUAGES" lang_con,
"RELIGIONS" rel_con
after inserting data from 3 different table (country, language, religion) the table looks like this....
Cyprus cy Nicosia Government controlled area 775927 9250 VARCHAR(English,Greek,Turkish) VARCHAR(Greek Orthodox,Muslim)
Czech Republic cz Prague Prague 10246178 78866 VARCHAR(Czech) VARCHAR(Orthodox,Protestant,Roman Catholic)
Germany de Berlin Berlin 82424609 357021 VARCHAR(German) VARCHAR(Muslim,Protestant,Roman Catholic)
Djibouti dj Jibuti Jibuti 466900 23000 VARCHAR(Afar,Arabic,French,Somali) VARCHAR(Christian,Muslim)
Denmark dk Copenhagen Frederiksberg Kommune 5413392 43094 VARCHAR(Danish,Faroese,German,Greenlandic) VARCHAR(Evangelical Lutheran,Muslim)
now I want to get the countries in which german language is being spoken. Actually I need to know how to search in this custom data type of mine....I also need to perform other operation further so really need to know how can I search in this custom data type...
when I execute the following query....
select * from country_n cn where cn.languages like '%German%' order by name
I got the following error....
Error starting at line 1 in command:
select * from country_n cn where cn.languages like '%German%' order by name
Error at Command Line:1 Column:33
Error report:
SQL Error: ORA-00932: inconsistent datatypes: expected NUMBER got AHMADM.LANG_CON
00932. 00000 - "inconsistent datatypes: expected %s got %s"
*Cause:
*Action:
let me know please...looking forward to your replies....
Thanks,

Hi,
Try this:
Connected to Oracle Database 10g Express Edition Release 10.2.0.1.0
Connected as hr
SQL>
SQL> SELECT t1.*
2    FROM country_n t1,
3         TABLE(t1.languages) t2
4   WHERE column_value LIKE '%German%';
NAME                                     CODE CAPITAL                                  PROVINCE                                 POPULATION       AREA LANGUAGES RELIGIONS
Germany                                  de   Berlin                                   Berlin                                     82424609     357021 <Object> <Object>
SQL> Regards,

How can i build RPMs file for my own Java Application?

How can i build RPMs file for my own Java Application?....I have my own directory that contains all Java Source files and some files that my Application required....I want to build RPMs file like a install File to Linux System, Now my OS is Linux Fedora core 1.....How can i do this?

I think that in order to create a RPM, you'd need to
use some C.Nope - the RPM is all about packaging and the "magic" x.spec file. You can have anything you want in the RPM, but you have to use RPM tools to build the .rpm file. One of the features is that you can also indicate (via "install" scripts) modifications to other files or the filesystem to support the installation of whatever's in the RPM.

How can i build table with two user name columne ?

How can I build view with two columns for user name ( one create and the other
Can change also )
And to display full name ( the user name is the key but not display ) ?

Hi,
Creating View
     From initial screen of data dictionary(T.Code: SE11), enter the name of object i.e. view.
     Select view radio button and click on the push button.
     Dialog box is displayed for types of views.
     Select the view type.
     On the next screen, you have to pass following parameters.
     Short text
     In the table box you need to enter the table names, which are to be related.
     In join table box you need to join the two tables.
     Click on the TABFIELD. System displays the dialog box for all the table fields and user can select the fields from this screen. These fields are displayed in the view fields box.
     Save and Activate: When the view is activated, view is automatically created in the underlying database system. As long as the table exists in the database, the view also exists (Unless you delete it).
Regards,
Bhaskar

How can you build time series measures in OBIEE without using TODATE AGO fu

How can you build time series measures in OBIEE without using TODATE and AGO function?
Please provide steps to build time series
measures in OBIEE without using TODATE and
AGO function. Dashboard results not storing
in cache when using TODATE and AGO functions.
eventhough its cached users queries not
hitting cache because queries doesn't match
exact date time when using TODATE and AGO
functions. so I want to build queries using
sysdate and some simple calculations. Please
send your inputs/ideas for my questions..
Thanks in Advance

This can be using Msum function in answers. Use the following formula, here dollars is my metric. Change the formula based on your metric.
Msum("Sales Measures".Dollars ,2) - "Sales Measures".Dollars
the report will be cached and better performed compared with time series. check ti
- Madan Thota

How could I build my own TOOL in Photoshop CS2

How could I build my own TOOL in Photoshop CS2? Like building a new Brush tool which could draw very fancy lines in Photoshop opened images.

You can't create a tool in Photoshop, but you can in your own filter plugin (similar to extract or liquify).

How can i build a manchester coding in labview signal processing?

how can i build a manchester coding in labview signal processing?
mean to say that how can i digitize my audio input.i waqnt to convert my audio input into manchester coded data format!!!
kindly post related VIs
regards
Solved!
Go to Solution.

idma-
Check out the LabVIEW FPGA example http://zone.ni.com/devzone/cda/epd/p/id/6126
Generate Manchester Signal
Basic example showing generation of a Manchester encoded data stream. The data to be sent is generated in one loop and passed to a FPGA FIFO. The subVI which generates the Manchester data stream reads the data bytes form the FIFO and passes them to the digital output. The subVI prepends a simple header to each data packet which allows a reader (see next example) to synchronize and acquire/parse the data. The header consists of a thee half bit pulse followed by a one half bit pulse. The three half bit pulse is not a valid component of regular Manchester encoding and can therefore be differentiated from the rest of the protocol. In addition it can be used by the receiver to to easily measure the bit rate of the protocol. By dividing the length of the three half bit pulse in half (3/4 of a bit), the receiver has a measure to differentiate between full and half bit pulses in the rest of the protocol.
Generate and Read Manchester Signal
An extension of the previous example which adds a Manchester receiver subVI. You must physically wire the digital output channel to your input channel to loop back the data outside the I/O connector of your FPGA R series card or C series module. The Manchester receiver subVI is expecting the data packet to be prepended by a header as explained in the previous section.
I will see if the is a more precise example but this should help
Sam S
Applications Engineer
National Instruments

How can we get Dynamic columns and data with RTF Templates in BI Publisher

How can we get Dynamic columns and data with RTf Templates.
My requirement is :
create table xxinv_item_pei_taginfo(item_id number,
Organization_id number,
item varchar2(4000),
record_type varchar2(4000),
record_value CLOB,
State varchar2(4000));
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'USES','fever','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'HOW TO USE','one tablet daily','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'SIDE EFFECTS','XYZ','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'DRUG INTERACTION','ABC','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'OVERDOSE','Go and see doctor','TX');
insert into xxinv_item_pei_taginfo values( 493991 ,224, '1265-D30', 'NOTES','Take after meal','TX');
select * from xxinv_item_pei_taginfo;
Item id Org Id Item Record_type Record_value State
493991     224     1265-D30     USES     fever     TX
493991     224     1265-D30     HOW TO USE     one tablet daily     TX
493991     224     1265-D30     SIDE EFFECTS     XYZ     TX
493991     224     1265-D30     DRUG INTERACTION     ABC     TX
493991     224     1265-D30     OVERDOSE      Go and see doctor     TX
493991     224     1265-D30     NOTES     Take after meal     TX
Above is my data
I have to fetch the record_type from a lookup where I can have any of the record type, sometime USES, HOW TO USE, SIDE EFFECTS and sometimes some other set of record types
In my report I have to get these record typpes as field name dynamically whichever is available in that lookup and record values against them.
its a BI Publisher report.
please suggest

if you have data in db then you can create xml with needed structure
and so you can create bip report
do you have errors or .... ?

How can i get acsess to my data if my iphone is shut and can´t open any more??how can i get acsess to the memory card, how can i get acsess to my data if my iphone is shut and can´t open any more??how can i get acsess to the memory card

how can i get acsess to my data if my iphone is shut and can´t open any more??how can i get acsess to the memory card????please help

You can't. There is no memory card. It uses flash memory that's soldered to the logic board. If you didn't back it up, your data is gone.

HOW CAN I USE MY OWN EMAIL FOR IMESSAGE IF I DONT HAVE MY OWN ACCOUNT

HOW CAN I USE MY OWN EMAIL FOR IMESSAGE IF I DONT HAVE MY OWN ACCOUNT

You have to achieve at least 500 points before you are able to do that.
Award points, level up, and earn new privileges

How can we update the last synchronization date and time..on SUP in sccm 2012 R2

Hi,
Can you any one please guide me how can i update the last synchronization date & time in SUP on SCCM2012 r2 , some how its updated as future date and when ever i try to synch the SUP with disconnected WSUS its shows in the wsyncmgr.log
"Wakeup for a polling cycle " and " Wakeupby inbox drop" and "Wakeup by SCF change"
Thanks
Balaji K

You'll probably have to call CSS on this one as this not normal by any means. The messages you noted above are completely normal but if that's all you are seeing then there's an issue.
Have you reviewed wcm.log and wsusctrl.log?
Jason | http://blog.configmgrftw.com | @jasonsandys

HT2486 how can I export the contact book data to a csv file for editing?

how can I export the contact book data to a csv file for editing?

You can edit a card right in Contacts. No need to export and re-import.
Select a name and on the right side, click the Edit button:

How can you save an app's data?

Hi, how can you save an app's data? For example, if I want to switch some applications on my iPod with those were on my iTunes Apps Library, iTunes will force to remove the apps that was on my device and sync the apps that I want onto my iPod. But once the app is removed from my iPod, its data will be erased too, so, for example months later, I want to put them back onto my iPod, I will lose all the apps data and games progress. So, I just want to know the way that people save their apps data.

Yo can't. apps are locked to the account thatpurchased them and in-app purchases can only be mad with the account that originally purchased the app.
You will have to recover use of the first account
How do I change or recover a forgotten Apple ID Password?
If you've forgotten your Apple ID Password or want to change it, go to My Apple ID and follow the instructions. SeeChanging your Apple ID password if you'd like more information.
If necessary:
Forgotten Security Questions/Answers
You need to contact Apple by:
1 - Use the Express lane and start here:
https://expresslane.apple.com
then click More Products and Services>Apple ID>Other Apple ID Topics>Forgotten Apple ID security questions.
or
Apple - Support -form iTunes Store - Contact Us
2 - Call Apple in your country by getting the number from here:
http://support.apple.com/kb/HE57
or
Apple ID: Contacting Apple for help with Apple ID account security
3 - Use your rescue email address if you set one up
Rescue email address and how to reset Apple ID security questions
For general information see:
Apple ID: All about Apple ID security questions
If you have not uses any of the $10 you redeemed to the new account, you can likely get that refunded by contacting iTunes
Contact iTunes

I cannot log in my game center using a same nickname after i updated my phone to ios 7. All my game data i was playing for months is lost. Seems when i try to put my nickname its already in used. How can i recover all my game data back?

All my game data i was playing for months was lost. Seems when i trie to put my nickname its already in used. So i need to put a new nickname then it create a whole new acc for me. All my previous data was lost. How can i recover my all my data or use my old nickname? Pls help

kerryp123
Yes, it is the same with me. I know a friend how upgraded to iso7 and lost all of his game center data. He tried singning in and re singning in but no change. Plus on to of all of this, apple is like have me and him to re-validate our itunes acount. Somthing weried is going on. So verified my itunes acount and it shows under settings that I am signed in, but when I go to the app store on my iPhone and try downloading or even updating a app, it says "can not conect to itunes store" after singing in! AND I'M NOT SURE I AM GOING TO UPGRADE TO ISO7 YET UNTILL THEY FIX THIS BUG!!!! HELP!

How can i build my own varient data type?

Similar Messages

Maybe you are looking for