How can i check the dsp work properly on cisco 2851?

Hello all.
There are somthing wrong with voice gateway in our gateway.
One of the E1 channel can't make a call from local pod to remote pod.
PABX engineer told me, he tried to make a call manually seizing spefic one of the E1 channel using his digital phone to check E1 channel testing, he found some channel can't make a call.
He called the symtom as "lockout".
the logout status means, they can't make a call specific channel eventhough the channel not busy.
so i check the status of the gateway using "sh isdn services", but all channel are idle.
ISDN Se1/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ISDN Se1/0/1:15, Channel [1-31]
Configured Isdn Interface (dsl) 1
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
At that time, i had debug on local gateway.
I can't understand the cause code...and status
*Oct 18 18:40:59.815 KST: ISDN Se1/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3202
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839C
Exclusive, Channel 28
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x2180, '615861200'
Plan:ISDN, Type:National
Called Party Number i = 0x81, '9680100'
Plan:ISDN, Type:Unknown
Sending Complete
*Oct 18 18:40:59.823 KST: ISDN Se1/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xB202
Channel ID i = 0xA9839C
Exclusive, Channel 28
*Oct 18 18:41:00.167 KST: ISDN Se1/0/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xB202
*Oct 18 18:41:02.955 KST: ISDN Se1/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xB202
*Oct 18 18:41:02.959 KST: ISDN Se1/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xB202
Cause i = 0x80AC - Requested circuit/channel not available
*Oct 18 18:41:02.979 KST: ISDN Se1/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x3202
*Oct 18 18:41:02.979 KST: ISDN Se1/0/0:15
**ERROR**: Ux_BadMsg: Invalid Message for call state 11, call id 0xD, call ref 0xB202, event 0xF
*Oct 18 18:41:02.979 KST: ISDN Se1/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0xB202
Cause i = 0x80E20F - Message not compatible with call state or not implemented
Call State i = 0x0B
*Oct 18 18:41:03.039 KST: ISDN Se1/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x3202
*Oct 18 18:41:03.039 KST: ISDN Se1/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB202
Voice gateway are connected NEC PBX and Nortel Meridian.
Problems occured both PBX systems.
I'm not sure the problem caused by PABX or Gateway.
How can i check it?
Regard,
john.

Hello.
Here is the partial configuration on gateway.
controller E1 1/0/0
framing NO-CRC4
pri-group timeslots 1-31
description << NEC NEAX-1 >>
controller E1 1/0/1
framing NO-CRC4
pri-group timeslots 1-31
description << NEC NEAX-2 >>
interface Serial1/0/0:15
no ip address
isdn switch-type primary-ntt
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
interface Serial1/0/1:15
no ip address
isdn switch-type primary-ntt
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
voice-port 1/0/0:15
no comfort-noise
busyout action shutdown
busyout monitor GigabitEthernet0/0
voice-port 1/0/1:15
no comfort-noise
busyout action shutdown
busyout monitor GigabitEthernet0/0
dial-peer voice 1 pots
description << A -> B >>
destination-pattern .T
no digit-strip
direct-inward-dial
port 1/0/0:15
dial-peer voice 2 pots
description << C -> B >>
destination-pattern .T
no digit-strip
direct-inward-dial
port 1/0/1:15
dial-peer voice 500 voip
description << 1586 >>
destination-pattern 1586....
session target ipv4:192.168.254.2
codec g711ulaw
no vad
dial-peer voice 501 voip
description << 1586 >>
preference 10
destination-pattern 1586....
session target ipv4:192.168.254.34
codec g711ulaw
no vad
Other dial-peers are omitted
dial-peer voice 7777 voip
description << Dummy Dial-peer for Codec Negotiation >>
incoming called-number .T
codec g711ulaw
no vad
Additionally, the NEC PBX was configuted it's isdn switch type ETSI.
But our gateway's isdn switch type is primary-ntt.
Regard,
john.

Similar Messages

  • How can i check the realtime ability of my program with LV 6.1?

    Hi, i did use a PXI-6053E daq card with Labview RT 6.0.3, after upgrading to
    LV 6.1 the single scan vi in my control loop displays no error, if i put too
    much stuff in the loop. i check data remaining, everything exactly as in
    the example i attached. With Labview 6.0.3 i did use the opcode "read
    oldest" all the time and got a "1" at data remaining output if runnig too
    slow. How can i check the realtime ability of my Program with LV 6.1? The
    attached example is running with 35kHz and green RT-LED, even if i put a
    "wait 1 ms" in the loop.
    Thx4help.
    Joerg
    [Attachment Optimized HW Timed Loop.llb, see below]
    Attachments:
    Optimized_HW_Timed_Loop.llb ‏242 KB

    You should still be able to use the data remaining output of AI SingleScan to indicate that you are maintaining real-time as you did in LabVIEW 6.0.3. If this is not working properly for you, you might try wiping out the ni-rt folder on the RT system and re-installing the RT software on it through MAX on your host computer. Check the versions you have. If you are still seeing data remaining = 0 even when you are running your loop significantly slower than your scan rate, you might want to contact the LabVIEW RT group at National Instruments for additional assistance.

  • How can I move the ODI Work Repository from one server to another server?

    How can I move the ODI Work Repository from one server to another server?

    Hi,
    If you would like to move your source models, target models and project contents from Work repository 1 to another work repository.
    I.e. Dev. server to Prod Server.
    1. Firstly, replicate the master repository connections i.e. with same naming conventions manually
    2. Go to Dev. Server work repository -> File Tab -> Click on Export work repository (save it in a folder)
    3. After exporting, you can view the xml files in the folders.
    4. Now, Open the Prod. server and make sure you already replicated mas. rep. details.
    5. Now, right click on model and import source model in synonym mode insert_update (select source model from the folder where your xml file located)
    6. Similarily, import again target then Project.
    Now, check. It should work.
    Thank you.

  • IP Job in BW finished, but how can I check the IDoc receive status in BW ?

    Hi,experts
    After I execute a Infopackage with loading more than 200000 records data, the infopackage monitor show me yellow light, 186020 from 200000 records. this infomation still show me till now, seaval hours,it looks pause here.
    And I check the request in the R/3, the Job has finished. as you know it means the R/3 push the IDoc already finished.
    and how can I do now ? or how can I check the IDoc receive status in BW side?

    Hi,
    I too had the same problem, i executed the following to solve the proble, may be this will help you:
    1) Go to T-code SM58 and select TRFC and press F6,
    2) For manual push of I-Docs, GO to T-COde BD87 select perticular idoc and see the status if it is not executed properly then do the manual push by pressing Execute option,
    Thanks,

  • I have two email accounts. It is only letting me check one. How can I check the other?

    I registered two different email accounts on my iPad mini. It's only letting me check one. How can I check the other one too?

    Congratuations on your new iPad!
    Since your device is so new, I can state categorically that this an issue with configuration. Delete the account that doesn't work, and enter the information anew.
    If you're still having problems, check that your email address and password are correct, and if possible, verify it by checking your ISP's settings.

  • How can i check the office web app server(wac client) is calling custom WOPI host?

    I am getting an error when I testing my wopi host(which is the same as
    example) with Office Web app server "Sorry, there was a problem and we can't open this document.  If this happens again, try opening the document in Microsoft Word."
    1-how can find the log files of this error?
    2-how can i check the office web app server(wac client) is calling my WOPI host?
    I am not sure about cumunication between owa to wopi host. I actually dont know how to implement checkfile and getfile functions to wopi host for waiting for call back from owa client.
    Note:I am sure that office web app server is configured true. Because i test it with sharepoint 2013 and editing and viewing is working well.

    Hi,
    According to your post, my understanding is that
    CheckFileInfo is how the WOPI application gets information about the file and the permissions a user has on the file. It should have a URL that looks like this:
    HTTP://server/<...>/wopi*/files/<id>?access_token=<token>
    While CheckFileInfo provides information about a file, GetFile returns the file itself. It should have a URL that looks like this:
    HTTP://server/<...>/wopi*/files/<id>/contents?access_token=<token>
    There is a great article for your reference.
    http://blogs.msdn.com/b/officedevdocs/archive/2013/03/20/introducing-wopi.aspx
    You can also refer to the following article which is about building an Office Web Apps(OWA) WOPI Host.
    http://blogs.msdn.com/b/scicoria/archive/2013/07/22/building-an-office-web-apps-owa-wopi-host.aspx
    Thanks & Regards,
    Jason
    Jason Guo
    TechNet Community Support

  • How can i check the license file installed on the server CCM 6.1.4

    Hi;
    i have installed the CCM 6.1.4; and now i want to upgrade to 8.5, but i don't remenber witch type license i have uploaded ( normal or Hospitality).
    how can i check the license file installed on this server???
    thanks.

    Hi Matthew,
    I think your idea should work just fine, but you will need to work with;
    [email protected]
    To put together the proper license file due to this change called the "License MAC"
    Customer Impact from New Licensing Procedures
    Cisco Unified Communications Manager on VMware on Cisco UCS B-Series Blade Servers uses a different licensing model than Cisco Unified Communications Manager on an MCS server. The MAC address of the NIC card is no longer used to associate the license to the server.
    Instead, the license gets associated to a license MAC, which is a 12 digit HEX value created by hashing the following parameters that you configure on the server:
    •Time zone
    •NTP server 1 (or "none")
    •NIC speed (or "auto")
    •Hostname
    •IP Address (or "dhcp")
    •IP Mask (or "dhcp")
    •Gateway Address (or "dhcp")
    •Primary DNS (or "dhcp")
    •SMTP server (or "none")
    •Certificate Information (Organization, Unit, Location, State, Country)
    This hash of these fields is called the LICENSE MAC
    Note : Once there is a change in any of the parameters that creates the License MAC, it will
    give you 30 day grace period to generate a new license file for the CM based on new license
    MAC.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/install/8_0_2/install/cmins802.html#wp584709
    Cheers!
    Rob

  • How can i check the planned data vs actual data

    How can i check the planned data vs actual data with the infocubes?

    Hi Srinivas,
    You create one cube for plan data and create another cube for actual data.
    Create a multiprovider and give comparision report. this is betterway.
    Or you can also load actual and plan data in one cube but you need to maintain one character like version to seperate atual and plan data.This is not a good work.
    Regards,
    Vijay.

  • How can I check the ink level in my Hp printer j4580

    I am so frustated, and upset with my hp printer, the only thing I waant to is how can I check the ink level in my Hp printer j4580, sound simple, well I have spend hours traying, and  I still don't know how to do it. This is ridicule

    Hello manguelo,
    Welcome to the HP Forums.
    I see that you are attempting to check the ink levels on the printer.
    Here is a link that will take you to a document that gives detailed instructions on Checking Ink Levels for HP Officejet J4500 and J4600 All-in-One Printer Series.
    Please feel free to write me back if you have any other questions or concerns.
    Cheers,  
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • How can I check the expiration date of a Certificate Keychain from terminal?

    Hello, I am writing a bash script to alert me when my corporate certificates are about to expire. How can I check the expiration date of a certificate in keychain? I'm running Mac OS 10.6.8 on a newer MacBook pro with full admin rights.
    Specifically I will be checking three certs: a Root Authority, Issuing Authority, and a user cert (Identity).
    I was exploring the Security and Openssl command line tools. But I can't seem to get the info I need.
    Any recommendations would be appreciated.
    Thank you!

    Anyone?

  • How can I check the specs with a broken LCD?

    A friend just gave me an ibook, but the LCD does not come on. How can I check the specs of the computer?
    I tried hooking it up to an external monitor, but I believe I need to setup the prefs to show on the external (I.E. the external was just black, but the computer was on).
    Any ideas here?
    All I know about the computer is that it's a white ibook with dual USB ports, firewire, and eithernet port on the side.
    Thanks in advance.
    -brown
    Message was edited by: Ryan Brown2

    The specs for the iBook should be on the label with the serial number.
    http://support.apple.com/kb/TA27282?viewlocale=en_US
    What does it say there?

  • How can I check the version of the rdf file?

    Dear all:
    How can I check the version of the rdf file? such like CEXRECRE.rdf .
    my environment is : oracle 11.5.9
    platform : Linux red hat 4.0
    Regards
    Terry

    Terry,
    Use "adident" or "strings -a" commands -- See (Note: 125922.1 - How To Find Oracle Application File Versions) for details.
    Thanks,
    Hussein

  • How can I check the version of Oracle in Linux?

    Dear all :
    How can I check the version of Oracle in Linux ?
    Regards
    Terry

    Hi terry;
    How can I check the version of Oracle in Linux ?You mean your db version or something else? If you mean you want to control your version issue is:
    source env file as oramgr
    sqlplus "/as sysdba"
    when u login sqlplus it will give u something as below:
    SQL*Plus: Release 10.2.0.4.0 - Production on
    Regard
    Helios

  • How can i check the file  which is upload from  the server

    when upload the excel file from the server file to the internal table ,how can i check the data whether it accord with  the required condition .
    for example ,i want to upload the file which have the data whose type is pack, and it have three integer and  two decimal ,how can i check in my code.
    thanks,

    Hi Sichen,
    First upload the file, Then do ur validations and delete the records that doesn't satisfy ur requirements.
    Thanks,
    Vinod.

  • How can I check the open-mode of an opened file from the file refNum?

    How can I check the open-mode of an opened file from the file refNum?
    Especially whether a file is opened as read-only or write-only? I haven't found any VI in the panel with file VIs.
    Thanks for any hints!

    Check this post. Probably you can use a kernel.dll call.
    http://forums.ni.com/t5/LabVIEW/file-date-created/m-p/109836

Maybe you are looking for