How can i configure Internal Challan-J1INCHLN?

Hi,
In Withholding Tax-for internal challan-J1INCHLN, what configuration do i need to do? Kindly help me.
Thanks
KB

Dear,
For these...
1. Entire extended withholding tax configuration must have been maintained..
2. Transaction must have been posted with withholding tax..
3. Use transaction J1INUMBER and maintain number ranges..
Regards,
Chintan Joshi

Similar Messages

How can we configure the width of the table in SAP DB

Hello sirs,
How can we configure the width of the table in SAP DB? (<b>i.e to specify the total width of the sum of all columns</b>). I need to change the default value of table width for adding fields with biggger sizes...
With best regards,
Sudheesh....

Hi,
The restrictions for using SAPDB are available at the following link http://dev.mysql.com/doc/maxdb/en/f6/069940ccd42a54e10000000a1550b0/content.htm
The 'internal length of the table' is 8088 bytes, which intern maps to the column width attribute.
Can we change the column width?
The answer is 'NO'.
check the general Column width error (-1115) at link below where it is specified that the column width can be altered http://dev.mysql.com/doc/maxdb/en/bb/57f18204fd11d2a96c00a0c9449261/content.htm
Refer link below for more details on the width of each column (based on the datatype associated with the column). http://orgs.man.ac.uk/documentation/mysql/manual_Column_types.html
So we will have to judiciously look into the boundary values for each column and set the right length because if the column is char(200) and it holds a null value then length allocated is 200 bytes.
The restriction cannot be broken.
Regards,
S.Divakar

HT4623 please help!! how can i configure my iphone 3gs because i've been updated a new version i did it but it's hard to activate it again.

please help!! how can i configure my iphone 3gs because i've been updated a new version, i did it but it's hard to activate it again. this message i always recieved in my iphone
"We're sorry, we are unable to continue with your activation at this time."

You phone was hacked. You can not get help with it here. Hacking / Jailbreaking voids any warraty and forfeits your right to support. Discussing jailbroken / hacked devices is forbidden by the terms of service here.

How can I configure iCloud so it doesn't restore deleted or moved emails on my Mac?

I moved to iCloud, and so far it looks like everything is where it's supposed to be. My question is about syncing. When I delete an email on my Mac, iCloud restores it. How can I configure iCloud so that changes I make on my Mac and my iPhone stay changed?

On the Mac in System Preferences > iCloud
Make sure Mail & Notes is selected.
ON the iPhone tap Settings > iCloud
Make sure Mail is switched on.
And try restarting your Mac and iPhone.

How can I configure my new Mac Pro to output the timeline via HDMI

How can I configure my new Mac Pro to output the timeline in FCP 7 (yes, I have X, but I'm using 7 right now). I have two monitors running from TB2, but want to have the third for a client monitor.
If I use all three via TB2, it's literally three monitors, and I want to edit on my CineDisplay. I only want the client to see the timeline video on the third monitor. When I hook up HDMI I get no signal, in fact, I can't have the HDMI cable hooked up for TB2 to work with the third.
Thanks,
GEvans
DarthPro
3.7 QCIntelXeonE5
12 GB
AMD FirePro dual D300 2048MB
OSX 10.9.2

If you use all ThunderBolt displays, or stick with DisplayPort and Mini DisplayPort (free conversion between the two with only a cheap cable) you can have up to six displays.
If you attach "legacy" displays with "any-old adapter", you can have up to two, and the built-in HDMI counts as one if you use it.
Any more requires ACTIVE Adapters.
The US$100 Apple ACTIVE Mini DisplayPort to Dual-Link DVI adapter works in every case, even displays over 1920 wide.
StarTech and Accell make US$35 ACTIVE adpters that work for displays up to 1920 wide.

HT4356 How can I configure the printer to print only grey tones from my iPad 2? Printer=Hp6520

How can I configure printer with iPad to print only grey tones? This works fine from my laptop - not air printing from that one though. I can't find anywhere on the iPad how to do printer settings and this also seems not to be available as an option when doing a printout. In fact, no options seem to be available. Thanks in advance for reacting!
Hermi

There is currently no option for this. You can give Apple feedback here:
http://www.apple.com/feedback/ipad.html

How can I configure ReFS to NOT fail read operations when a checksum error is detected (on non-Storage-Spaces volumes where data integrity streams are enabled)?

According to William Stanek, in his Windows Server 2012 R2 Inside Out: Configuration, Storage & Essentials book, this is apparently possible: (pg. 615 - here it is on Google Books: https://books.google.ca/books?id=0IyfBAAAQBAJ&pg=PT819&lpg=PT819&dq=read+operation )
Integrity can be enabled when the system is not running on Storage Spaces. When
integrity is enabled and ReFS detects a checksum mismatch, ReFS logs an event and
fails the read operation by default. If you don’t want the read operation to fail, you
can configure ReFS to continue with the read operation. A related event will be logged
regardless.
So then how do I configure it to do that???
(And just to make it super-clear, I'm NOT using Storage Spaces, so there is no redundancy via mirroring/parity, and I'm not expecting any file repair - just detection of corruption. It's just a basic volume formatted with ReFS and
with integrity streams enabled, via format E: /fs:ReFS /i:enabled
For those who want more details, here's the situation:
I try to perform a read operation on a file with corrupted data (purposely done for testing using a low-level disk editor), I get a the following error message:
And an event ID 133 from ReFSv1 gets logged in the System log:
Clicking "Try Again" just brings up the same message, and clicking "Skip" skips the operation entirely.
This is indeed the correct default behaviour.
What I want instead is for the read operation to be allowed to complete, with corrupt data and all, and ONLY for the event to be logged. And according to William Stanek, this is supposed to be configurable somewhere - and after hours of searching, I haven't
been able to find anything.

Hi Tommy,
>>How can I configure ReFS to NOT fail read operations when a checksum error is detected
We can use PowerShell command Set-FileIntegrity to configure this. The specific parameter for controlling this behavior is
-Enforce <Boolean>which indicates whether to enable blocking access to a file if integrity streams do not match the data.
Regarding this point, the following article can be referred to as reference.
Set-FileIntegrity
https://technet.microsoft.com/en-us/library/jj218351.aspx
Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

How can I configure a VM to boot from USB key in Virtual PC of Windows 7?

Hi all,
I want to boot up with a USB key to install a new VM on Windows 7. I heared that Microsoft Virtual PC begins to support USB device on Windows 7. How can i configure it? I don't find any virtual USB device in VM settings on my Windows 7 box.
Thanks for any help.
Scorprio
TechNet Software Assurance Managed Newsgroup MCTS: Windows Vista | Exchange Server 2007 MCITP: Enterprise Support Technician | Server & Enterprise Admin

Hi all,
I want to boot up with a USB key to install a new VM on Windows 7. I heared that Microsoft Virtual PC begins to support USB device on Windows 7. How can i configure it? I don't find any virtual USB device in VM settings on my Windows 7 box.
Thanks for any help.
Scorprio
TechNet Software Assurance Managed Newsgroup MCTS: Windows Vista | Exchange Server 2007 MCITP: Enterprise Support Technician | Server & Enterprise Admin
Virtual PC does not support USB. Windows 7 XP Mode Virtual Machine supports the use of USB devices. Virtual PC and Windows 7 XP Mode VM are not the same thing!

How can i configure advance payment to vendors through cash jounal

how can i configure advance payment to vendors through cash jounal pls its urgent for me kindly help me out

HI,
I think u need not configure anyting new for this, you can use the existing Business Tran. Type K and rename it as Vendor Advance for separate identity. You can do the normal FBCJ posting.
But doing this you will not have separate identity for the Advances paid.
Thanks
VK

My mac desktop will not provide sound from internal speakers. when I go to audio devices window it only shows airplay. How can I get internal speakers back.

My mac desktop will not provide sound from internal speakers. When I go to audio devices window it only shows airplay. How can I get internal speakers back.

There are many possible causes for this issue. Take each of the following steps that you haven't already tried. Some may not apply to your model. Back up all data before making any changes.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Run Software Update and make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. Other third-party software that has been reported to interfere with sound output includes "Boom" and "Samsung Kies." If applicable, uninstall according to the developer's instructions (not by dragging something to the Trash.)
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select Built-in Output from the list on the left. If the Mute boxes are checked, uncheck them.
7. If a red light is visible in the audio-out port when sound should be playing, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do not appear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/Audio
Right-click or control-click the highlighted line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and empty the Trash. Recreate your settings in the Sound preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
14. Reinstall OS X after backing up all data.
15. Make a "Genius" appointment at an Apple Store.

How can i configure STMS with out physical systems

Dear Experts ,
please solve my doubts
here i installed one system in AIX and named it as DEV system in that system i need to perform post-installaion Activities
and i started some activities also
presently my doubt is in STMS configuration
here i have only one system (DOMINE CONTROLLER) and we need to other systems while configuration but we dont have other systems like quality and production how can i configure that systems in my landscape
this is my first implementation Experience please suggest me with some valuable suggestions
my doubts:
while creating systems we need to take for virtual systems or Extended systems
which transport routes can i prefer for Dev to Qly systemand also Qly to Prd
please reply me
Regards

Hi,
If you have decided the SID's of the QUA and PRD systems then you can configure TMS with the virtual systems. Here are the steps to do so.
Login to the domain controller
Execute tcode STMS
Goto the menu overvie --> systems (Shift+F6)
SAP SYStems --> Create --> Virtual system
Enter the SID and description and then save ur entries.
Now the new virtual system will be created. Do the above for the others systems in the landscape.
Again execute STMS and then click SHIFT+F7. You will goto the transport route window. Now you can configure TMS for the systems in the list as usual.
Hope this helps.
Regards,
Varadharajan M

How can I configure NI PCI 6221 and DAQ SCB-68 for pressure sensors?

Hello
everybody,
I am using the measuring board (NI PCI 6221) and DAQ
SCB-68 for the data acquisition.
With the DAQ-Assistant I created AI for the voltage of
pressure sensors. In a big indicator panel from this DAQ-Assistant I see the
voltage for both sensors in the correct size. But if I set sensors in the
blockdiagramm to control the signals for sensor one I get a wrong voltage size
and for sensor 2 nothing.
How can I configure this data acquisition equipment to
get the correct signals?
Thanks a lot for your help.

I do not know the type of sensor you are using. But pressure transducers may have a very low output voltage(in the mVolt range). They also need an excitation voltage. Here is an introduction. http://focus.ti.com.cn/cn/lit/an/sloa034/sloa034.pdfThen working with pressure sensors I always use 3 stages in the circuit.
1 Instrumentation Amplifier as a preamp
2 filterstage
3 Final amp and output buffer
(you may combine stage 2 and 3)
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

HT3887 how can i configure my wireless keyword so i can use the Function F keys to control volume etc...? I am using 10.5.8 OS

how can i configure my wireless keyword so i can use the Function <F> keys to control volume etc...? I am using 10.5.8 OS

little wireless cameras would not have the ability to send back to the base, even thought the base can reach it.
Now if you take regular cameras and wire them into a Cisco switch that was attached to a wireless bridge that could shine back to the base...now you might have something, but your still going to have to do a survey/path analysis to determine if it is feasible.
Coverage isnt throughput. I see one base station with 3 or 4 sectoral antennas depending on direction, pointing two several distribution bridges to bridge the gaps that go out again to the cameras...something like that. And all of it should be higher in the air than your construction.

How can I configure MA to display "speaking" OpCode and Task names

If you have a custom ETW Eventsource definition: PerfView reads and Displays from the etl files the OpCode and Task values not as integer but as defined in EventSource inner classe for Task and in the
System.Diagnostics.Tracing.EventOpCode. My question is, how can I configure the MA to display the values not as "magic numbers" or can MA get this feature?
Regards,
Alexander
Kind regards, Alexander

Hi Paul,
please take a look to the attached picture. I've tried to make a comparison between automatically behavior of PerfView and Message Analyzer by displaying of the same performance log. The Message Analyzer got metadata, generated with wevtutil. The related
part of the manifest is here:
<tasks>
<task name="ReadingFromGdb" value="1"/>
<task name="LogReadPreInvoke" value="65532"/>
</tasks>
<opcodes>
</opcodes>
<keywords>
<keyword name="Perf" message="$(string.keyword_Perf)" mask="0x8"/>
<keyword name="Gdb" message="$(string.keyword_Gdb)" mask="0x10"/>
</keywords>
<events>
<event value="8" version="0" level="win:Verbose" message="$(string.event_LogGdbReadPreInvoke)" keywords="Perf Gdb" opcode="win:Start" task="ReadingFromGdb" template="LogGdbReadPreInvokeArgs"/>
</events>
<templates>
<template tid="LogGdbReadPreInvokeArgs">
<data name="fullName" inType="win:UnicodeString"/>
<data name="methodName" inType="win:UnicodeString"/>
</template>
I hope, it helps you to understand details of my questions.
Regards,
Alexander
Kind regards, Alexander

How can we configure or control records go into single idoc thru BODS?

Hi,
Our case is -
IDOC format has three segment. Each segments has child nodes -
1. CONTROL SEGMENT - This is required only once per idoc.
child1
child2
2. SEGMENT1 - sinlge source record to be broken into two segments.
child1
child2
3. SEGMENT2 - sinlge source record to be broken into two segments.
child1
child2
we have a single source (lest say having 100 records).
In the current design which does generates IDOCS but as many as the no of records in source. Currently we use a row generation transform as dummy (with row count as 1) to pass to the IDOC parent nodes's from clause to escape the error - invalid input to the parent nodes.
Child nodes are either mapped to the source table or are null.
Question - How can we configure this in a way that we control how many records go into single idoc. Ex - lets say 50 per idoc so only 2 idoc should be created if 100 records are there.

HI,
this sounds to me like Data Services. If so I would suggest to post this into the Data Service forum.
regards
Ingo HIlgefort

How can i configure Internal Challan-J1INCHLN?

Similar Messages

Maybe you are looking for