How can I connect multiple airport express to airport extreme?

I have an Airport Extreme that is connected to my cable modem. I have 3 Airport Express that I would like to connect to the extreme to extend the signal in my home. I was able to connect 1 but I have been unable to successfully connect the other 2.
Can anyone tell me how o accomplish this?
Thanks

Power off all four AirPorts in any order that you want
Wait a minute, then power up the AirPort Extreme
Wait another minute and power up the AirPort Express that is working
Move the other two Express devices to the same room or close proximity to the AirPort Extreme
Power up one Express for a minute or two and leave the other Express off for now
Hold in the reset button on the back of the Express for 10 seconds and release
Allow a full minute for the Express to restart to a slow, blinking amber light status
Click the WiFi icon at the top of the Mac's screen
Look for a listing of New AirPort Base Station
Just below that, click on AirPort Express
That will start up the setup wizard. It will take minute to analyze things and then suggest that the Express be configured to extend the AirPort Extreme network.
Enter a short simple name to call the Express, something like Express2 for example, and click Next
The utility will set thing up for you. When you see the message of Setup Complete, click Done
Now move the Express upstairs and power it up. If the signal must pass through a ceiling, that is a tough assignment, since the ceiling is likely absorbing about half of the signal going through
Report on your results

Similar Messages

HT4262 How can I connect 6 computers simultaneously to Airport extreme?

I have tried troubleshooting several ways and the some computers work and others don't. How can I connect 6 wireless computers to Airport Extreme?

Matt
Is it possible to speak on the phone? The situation is so convoluted it might be easier to help me get back on track in person. When I first had this issue I got on an apple site that had a chat room in which I typed in my problem. After several missives back and forth, the apple technician asked for my number and we spoke on the phone. The technician walked me through rebooting the actual airport plug (as opposed to the router box) and got me up and running. Do you know how I can relocate that chat site for technical support?
Thanks
David

How can I connect my Apple TV and Airport Express to the rest of the network for the least lag?

Hey guys,
I have an Airport network here in the office. All new Airport Extremes. The internet comes into one, which then connects to our switches, which then connects to other Airport Extremes over ethernet. Everything is setup to create its own network with the same SSID, and only the leader is the DHCP server.
I recently added an Apple TV to the network, only it was too laggy for video chat. I bought an Airport Express (for the audio), and ran ethernet to connect it to the network and the Apple TV, but things were still slow.
Now, I set the Airport Express up as a DHCP server (with NAT) itself, with a separate SSID, and it's working great. The only problem is that people would rather not have to switch wifi networks. Is there any way around this? BTW, the AirEx is complaining about Double NAT, which I understand is happening, but it's still working fine... it's really just the having to switch networks that's a problem for us.
Thanks!

Hi - as you probably know, double NAT is not recommended - you might have problems with some websites and updating - but if it is working that is great - as far as the Wi-Fi issue is concerned, you should still be able to create a wireless network with the same name an password as the rest of your network so no one has to switch.

How can I connect multiple clients to a single client ?

I am currently developing an instant messaging program.I created a server and connected multiple clients to it by using thread logic.However I do not know how to connect multiple client to a single client.
What shall I do for that?Does anybody know a good tutorial or sample program?Or shall anybody explain me what I shall do for building the Instant Messaging part of my chat program?
Thank u in advance.

You may use UDP multicast socket. But since you are using the UDP protocol you might risk losing the data that you send since UDP does not guarantee the safe transfer of data.
Alternately, you might create a server that allows multiple client to connect to it whose connection Socket objects are then stored in a Vector <Socket> object. The server then sends back data to the connected client about the other clients connected to it. Now when the client wants to send data (like an IM) to another connected client, it has to send a request to the server specifying the client login name and the server in turn streams that particular client's Address and Port to the requesting client. The requesting client then initiates the connection with the other client and then starts a conversation. One more thing, when the client communicates it needs to send information to the server like the name by which it likes to be referenced. In this scenario the server acts like a central repository for clients to query the existence of other clients in the chat room. Each client here runs a thread that listens to incoming connections and when a connection is established, may be opens a IM window or something.
The third option is to make the server to relay the information from one client to another. Like say, I'm connected to whoopy server and i want to send "Hello" to jackson, then i send the message (ie, Hello) along with the name of the client to which i wish to send it to (ie, jackson). The server then performs a lookup in its Vector <Socket> object and then initiates a connection with jackson and sends the information. However, this method is pretty costly in that you will be wasting a lot of processing behind the server.
--Subhankar
P.s. If you stumble upon any other brilliant ideas let me know.

How can I connect multiple devices to Mac mini display port? I need to connect a Canon 5D to my Mac and display the result on a VGA video projector. I am using mini hdmi to mini display for the camera. Can I connect the VGA to any other port?

Hi there I am connecting a Canon 5D to my laptop trying to use it as a webcam trough camtwist.
At the same time I need to output the streaming to a videoprojector.
The cam is connected to the mini display port do there is no port available for the VGA cable anymore.
Do I need to use a different port for the projector? Should I buy a video card?
Can't connect the camera via USB as that is too slow and it will freeze.
Many thanks for all your help
Best
Faeve

You might do better on a forum other than this one, which is "Using iPhone"

How can i connect multiple forms using swings or applets(AWT) & with D-Base

Hello Friends,
I am Sreedhar from Hyderabad. working as a java developer in a small organization. I got a challenge to work on java stand alone (desktop) application. Basically our company is based on SCM(Supply Chain Management), I never work before using swings and AWT. now my present challenge is to develope an application on swings and AWT using Net Beans IDE. but i am unble find the code to connect one form to another form, i want to develop similar application like a web application , suppose if i click on OK button it has to connect next form. in the next for it has to take user name and password should allow me to access main form. please help me about this topic, if anybody interested i can send u the screen shots and i can post to ur mail. please help me as soon as possible,

sreedharkommuru wrote:
Hello Friends,
I am Sreedhar from Hyderabad. working as a java developer in a small organization. I got a challenge to work on java stand alone (desktop) application. Basically our company is based on SCM(Supply Chain Management), I never work before using swings and AWT. now my present challenge is to develope an application on swings and AWT using Net Beans IDE. but i am unble find the code to connect one form to another form, i want to develop similar application like a web application , suppose if i click on OK button it has to connect next form. in the next for it has to take user name and password should allow me to access main form. please help me about this topic, if anybody interested i can send u the screen shots and i can post to ur mail. please help me as soon as possible,There is no magic, you need to spend a good amount of time in tutorials, here is a good one to start off with:
[The Really Big Index|http://java.sun.com/docs/books/tutorial/reallybigindex.html]
Here are a few tips:
1 - Do not mix AWT and SWING: it'll just cause you headaches in the long run that you cannot fix without refactoring to properly not mix the 2 together.
2 - You use JDBC to access the database
3 - You make accessors/constructors to pass parameters that you need from one form to another.
Have fun.

How can i connect the Chrome to the Airport?

I boutht a Chrome to be connect with my laptos that does not have wi-fi but airport but it does not connect with the Chrome

Setup Apple TV with iPad
1. Setup Apple TV
(a) Connect cables and power cord
(b) Turn on TV and select Input
(c) Configure Apple TV
2. Setup Home Sharing on iPad
Settings>Music/Video>Home Sharing
3. Setup Home Sharing on Apple TV
Settings>Computer>Turn on Home Sharing. Enter Apple ID and Password
4. Pair Apple TV with Remote Control
General>Remotes>Pair Apple Remote

How can I connect Acer (WinXpSP2) to Mac airport extreme?

I cannot connect my ACER laptop using WinXP Sp2 to my Mac's Airport Extreme. I have set my System Preferences with a third party 13 character password. I did not make any changes to my Airport Admin Utility. I followed the steps laid out in the site: //www.ifelix.co.uk/tech/1011.html. I think I'm just probably missing one button to click or unclick. I have done the following to configure the Wireless properties on my ACER...so that the network authentication is selected at SHARED, the Data Encrytion is set at WEP; disable the IEEE 802.1x authentication for this network; and connect to wireless network manually. All this was recommended in the felix site and other help files but I cannot make the connection. Also, when the properties are set like I mention, for some reason ACER kicks everything to its default settings (WPA-PSK authentication, TKIP encryption, IEEE 802.1x authenication enabled....all I don't want)
What am I doing wrong? I know that Window XP SP2 does not need the windows firmware to get access to my mac airport extreme.
Help someone? PLEASSSE!
Rose

1, Change your airport wireless security from WEP (old fashion and not really that secure) to "WPA Personal".
2, Set yourself a password, then update your airport.
3, Delete your current wireless setting on your XP then do a new network search
4, You should found your airport wireless network on your xp by now, click, to join the network and type in and confirm the password you just set on your airport's "wirless security".
5. Done, you should be able to access the network now

How can I connect multiple speakers to the Mac Mini?

Just received and setup up my new Mac Mini (Dual-Core i7, 8GB memory, 750GB disk) with OS Lion. Still in newbie phase. I have a set of 3-way Boston Acoustic speakers (w/ subwoofer) from an old Gateway computer. Is there any way/adapter available to connect them to the Mac Mini in order to improve music played within iTunes. Appreciate your responses.

Here's Apple's link to information about scanners that are supported by Mac OS X:
http://www.apple.com/macosx/upgrade/scanners.html
-Doug

How far away can you connect to the internet from Airport Extreme (802.11n)

How far can i take my Laptop away from Airport Extreme (802.11n) and still have internet connection

According to:
http://www.apple.com/au/airportexpress/
They claim the Extreme has a 45m range:
"Suppose you want to connect to the Internet with your PowerBook in an area that lies beyond the 45 metre range of your AirPort Express or AirPort Extreme Base Station"
Will you be using all N devices? G?, B? or a combination?

How can I have multiple users on iTunes (in order to connect to a shared office iPad)?

How can I have multiple users on iTunes (in order to connect to a shared office iPad)? Currently each of us has our own iTunes account, so I've made an "all office" Apple ID. However, I can't seem to get two different accounts (my personal and the office) to work on my machine. Even when I login as "the office", my personal library is still showing. Additionally, when I try to setup with a first-time use in iTunes, I get an error that I don't meet the minimum age requirement - no matter what birthdate I enter!

The library exists regardless of which user is logged in.
The only way around that is to create different user accounts on the computer.
There is no way to have 20 unique iTunes users access a shared iTunes under a single login on the computer.

HT1998 How can I administer a Gen 1 Airport Express from Airport Utility 6.3.2 (OS 10.9). I can see the base station but get the message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more inform

How can I administer a Gen1 Airport Express from, my MacPro (OS 10.9, Airport Utility 6.3.2). I can see the Express in the WiFi window but from the Airport Utility I get the following message: " This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Of course there's nothing of value on the support page. Any clues anyone?

Apple has dropped support in Mavericks (10.9) of the AirPort Express and AirPort Extreme models that were discontinued more than six years ago.
You can still administer the older AirPort models if you have a Mac running Leopard, Snow Leopard, or a PC.

I installed an airport card in my powermac g4, how do I connect to my router (not an airport base.) How can I connect to my router?

I have a powermac g4 quicksilver in which I have installed a normal airport wireless card in the dedicated slot. How can I connect to my router? It is not an apple airbase station but does it need to be? How can I connect to my router?

What encryption is the Rouer using? If WPA2 you likely can't.
Go to System Preferences
Click Network
Highlight AirPort and click Configure...
What shows for Routers there? Or is Join Other Network availabe in 10.3.x?

How can i connect between WS−G5484 1000BASE−SX and GLC-LH-SMD ?

Dear experts,
My customer has 6509 A-side and B-side core switches and need to migrate only 6509 B-side to Nexus.
I have some question below.
1. Customer's 6509A-side has multiple WS−G5484 1000BASE−SX and WS−G5486 1000BASE−LX links and it is connected to 6509B-side.
But customer bought only GLC-LH-SMD for Nexus migration of 6509B-side.
I understood BLC-LH-SMD doesn't support SX type, so I am worndering how i can connect between 2 different module ?
Or should i have GLC-SX-MMD for WS−G5484 1000BASE−SX links ?
2. Current Rack has LC type patch pannel from B-side to Rack A side.
But new Nexus A-side rack is located at different row and between these rack, there is only sc-type patch pannel.
So If i want to connect from LC-type to Sc-type patch pannel, how can i connect ? do i have to use SC-LC converter ?
3. Old 6509 links use many MMF cable, and new Nexus use SMF.
Between same LX/LH links, if a side use MMF and another side use SMF, how can i connect each other ?
Again new Nexus A-side rack is located at different row and between these rack, there is only sc-type patch pannel.
Please let me know in detail, Thanks in advance, I really appreciate for your help.
Jason.

Hi Leo,
Thanks of your reply.
Dear Experts,
I seek your expert's advice for another question urgently.
Please make you time and share your experiecce.
Thanks.
Jason

How can I remove multiple copies of the same song from the iTunes listing?

How can I remove multiple copies of the same song from the iTunes listing. The program seems to be picking up the same songs from, for example, my user area and my public area in the C drive

As above, Apple's official advice is here... HT2905 - How to find and remove duplicate items in your iTunes library, however it is a manual process and the article fails to explain some of the potential pitfalls.
Use Shift > View > Show Exact Duplicate Items to display duplicates as this is normally a more useful selection. You need to manually select all but one of each group to remove. Sorting the list by Date Added may make it easier to select the appropriate tracks, however this works best when performed immediately after the dupes have been created. If you have multiple entries in iTunes connected to the same file on the hard drive then don't send to the recycle bin.
Use my DeDuper script if you're not sure, don't want to do it by hand, or want to preserve/merge ratings, play counts and playlist membership. See this thread for background and please take note of the warning to backup your library before deduping.
(If you don't see the menu bar press ALT to show it temporarily or CTRL+B to keep it displayed)
tt2

How can I connect multiple airport express to airport extreme?

Similar Messages

Maybe you are looking for