How can I connect the cFP-DIO-550 via a cFP-CB 1 with my circuit

hi
I use the module cFP-DIO-550 with a cFP-CB and I do not know how to connect my system with this module, for exemeple I want to connect the gate of a triac with the output 0 is that I need other electronic components or voltage sources.
thnx for help

The cFP-DIO-550 can be set to I/O logic levels of 12 or 24V DC.  What kind of voltages are you inputting/outputting?  Check the specifications of this module to see if the connections you're making will be adequate.

Similar Messages

  • How can I connect the iTunes in my iPad (now with iOS7) to my Power PC Mac?

    How can I connect the iTunes in my iPad (now with iOS7) to my Power PC Mac?

    Nope, the top OS version for the IBM processor is 10.5.8, and under that version I can not update the iTunes further than the 10.6.3 :-(
    But that means the brand leaves a large chunch os costumers with still perfectly operating computers out of the loop on purpose, so to force us to upgrade computer?
    Not fair at all, both are legitimate Apple products, they should sync no matter what! The sad thing is theu used to, before I migrated to iOS7 on the iPad, move that I now regret...

  • How can I connect the ipad2 to an Epson Stylus SX445W wifi printer?

    How can I connect the ipad2 to an Epson Stylus SX445W wifi printer?
    Any help appreciated. Obviously I'm not technically minded so simple... Sorry... Very simple instructions would be great. Thanks

    Does the iPad come up with a "no AirPrint printers found" message? If so, the most common fault is that the printer isn't on the same WiFi network as the iPad. Your printer may also need a firmware update. Epson has some support information here that may be of help:
    http://support.epson.net/airprint/fw.html
    Regards.

  • How can i connect the Faulhaber Motor to MID-7654?

    How can i connect the Faulhaber Motor (3564 024BC, with Encoder HEDM 5500 B12) to MID-7654?
    The Motor has following wires:
    A: Hall sensor green; A: Phase brown; B: Hall sensor blue; B: Phase orange; C:  Hall sensor gray;
    C: Phase yellow; +5V: Voltage red; GND: Ground black
    The Encoder has:
    5: Channel B; 4: Vcc; 3:            Channel A; 2: Channel I (Zero impulse); 1: GND
    I don't know how I can connect the encoder to MID-7654 using these wires (what is Encoder Index? Instead of this i only have Channel I !) 
    Thanks!
    WLAN

    Unfortunately there are different designators for the encoder signal which NI refers to as encoder index. In your case I am pretty sure that the I channel is identical to encoder index.
    Other designators I have found are Z (z-ero signal) and R (r-eference signal) for the index signal.
    Make sure that the index signal is at the correct level. For most applications it should be active low (i.e. it should be at high level during most of a turn and go low when the index mark passes the opto switch, I think it should be like this on most if not all Agilent optical encoders as you have it on your motor. This happens for a very small turning angle only and is hard to detect when turning an encoder/motor manually, so if you try to find the index signal turn the motor/encoder veeery slowly.

  • How can i connect the PO to Document No...pls help it urgent!

    Hi gurus!
    How can i connect the PO no. to Document NO. pls specify the tables and fields.. tnx!
    Regards,
    Mackoy

    Hi,
    the document no. that is attached to PO at tcode <b>ME23N</b>..what should i do?
    Tnx!
    Regards,
    Mackoy

  • HT1212 how can i connect the iPad to the iTunes if the iPad is locked

    how can i connect the iPad to the iTunes if the iPad is locked

    If you can't do the restore then you will need to try recovery mode.
    Read this: http://support.apple.com/kb/ht1808

  • How can i connect the mac with internet key?

    how can i connect the mac with internet key?
    I try but it tolds me that I haven't the javaruntime...

    I try, but to run javapreferences computer told me that I must have a Java runtime... thankyou

  • How can I connect the polaroid 6500 ultrasonic sensor ranging module to DaNI 2.0 robot (which is using sbRIO 9631)?

    How can I connect the polaroid 6500 ultrasonic sensor ranging module to DaNI 2.0 robot (which is using sbRIO 9631)?

    check this post
    http://forums.ni.com/t5/Real-Time-Measurement-and/sensor-on-sbrio/m-p/2030424#M11812

  • How can I connect the first generation ipod to macbook air?

    How can I connect the first generation ipod to macbook air or macbook pro? Using an adapter?

    macbook air
    The only theoretical solution is an USB ExpressCard adapter and FireWire ExpressCard. I don't know if anyone's actually attempted it.
    macbook pro
    A FireWire 400 to 800 cable or adapter, also known as 6 pin to 9 pin.
    (53970)

  • HT4356 I  from an iPad , but get, " no AirPrint printers found" , how can I connect the two devices?(I have followed all the usual network steps!

    I  am trying to airprint from an iPad , but get, " no AirPrint printers found" , how can I connect the two devices?(I have followed all the usual network steps!

    Make sure you have a AirPrint enabled printer.
    http://support.apple.com/kb/ht4356

  • How do you connects the same iPad to iTunes which is already synced with another computer

    How do you connects the same iPad to iTunes which is already synced with another computer

    You can only use one iTunes library at a time when you sync your devices. If you want to sync to a new computer now, look at this.
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive
    And here is another helpful article.
    http://www.howtogeek.com/104298/sync-your-ios-device-with-a-new-computer-without -losing-data/

  • I have an ipod touch second gen, how can i download the facebook app if it says its not compatable with my current iOS?

    i have an ipod touch second gen, how can i download the facebook app if it says its not compatable with my current iOS?
    i had the facebook app but i could never upgrade it and i was ok with using the outdated version but when i reset the ipod so i could gift it to a friend it obviously got rid of the app and now i cant downloaded because it says its not compatable, how can i download the version i had before i reset it?

    Your only way is if you have the version that was compatible on your computer such as in the recycle bin/trash or in a computer file backup. In that case delete the current version that is in your iTunes App library and replace it with the older version. Then sync.
    Also see:
    Recover Older Versions of iPhone Apps After Updating — Apple News, Tips and Reviews

  • How can I install the free version of adobe illustrator in a PC with Windows Vista?

    How can I install the free version of adobe illustrator in a PC with Windows Vista? When i try the program says that i haven't suitable system requirements

    Downloadable installation files available:
    Suites and Programs:  CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
    Acrobat:  XI, X | 9,8 | 9 standard
    Premiere Elements:  13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
    Photoshop Elements:  13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
    Lightroom:  5.7.1| 5 | 4 | 3
    Captivate:  8 | 7 | 6 | 5.5, 5 | 1
    Contribute:  CS5 | CS4, CS3 | 3,2
    FrameMaker:  12, 11, 10, 9, 8, 7.2
    Download and installation help for Adobe links
    Download and installation help for Prodesigntools links are listed on most linked pages.  They are critical; especially steps 1, 2 and 3.  If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.

  • In Messages, how can I get the most recent entries to appear on top, like with my emails?  Thanks!

    In Messages, how can I get the most recent entries to appear on top, like with my emails?  Thanks!

    HI,
    A Note.
    Technically the most recent Conversation (or Chat) that has a new message (be it iMessage or IM) will move to the top in the list on the left if it is set in the View  Menu to do so.
    Obviously this does need more than one Conversation or Chat to be listed to work.
    It does not change the focus of the Chat/Conversation you are viewing.
    iChat - the forerunner naver had an option to invert the chats.
    The iChat Feedback page is where I use.
    You will also see it does not list iChat 6 depsite listing Lion.
    In this sense it has always beeen out of step on the iChat/Messages version front  (it took me a long time via the Lounge and Host help to get it on the list of pages to be updated on New OS versions)
    11:00 PM      Friday; June 28, 2013
      iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.4)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • How can I connect the remote server which is installed with oracle

    Now my computer is in my home,in my computer there is installed with the oracle 9i client,the server is also installed with oracle 9i,which is in my company.Now I want to use sql*plus to connect the database of the server through the internet work.I have created one listener service name in my home computer,but can't test successfully and the sql*plus can't connect the database.Who can tell me how to do it?Thank you!

    Technical questions need to be addressed to one of the technical forums-- Products | Database | Database - General in this case.
    Unless you are VPN-ing in or the DBA's at your company have configured Oracle Connection Manager to allow you to connect through the firewall to the database, however, I doubt this will work. If they have configured Connection Manager, you'll have to ask them to provide you with connection information. 99.9% of the time, you do not want people to access a database via the internet.
    Justin
    Distributed Database Consulting, Inc.
    http://www.ddbcinc.com/askDDBC

Maybe you are looking for