How can I control my step motor

I am using a 6006-DB 3-mothor driver and a NEMA step motor model 405-SM, both from AMSI corp. I would like to control my step motor using LabVIEW. We use the LV. 5.1.1 version and we have a PCI-MIO-16E-40 as adquisition card.
The sistem I want to built is to control my step motor and while turning detect the intesity variation on a photodetector which is conected to my adquisition card.
I wonder if somebody has an idea how to do that.
Thank you in advance
Daniel Hernandez

Ok I understood, I can use my PCI-MIO-16E card to control my steper motor driver, I will try to do that. But, if I use a DB-25 connector, how can I use my PCI card??
I was thinking to use the parallel port, directly, to conect my steper motor driver.
I attache some VI someone passed me. (It use a Setbit.vi and out port.vi)
Attachments:
MoteurGOTO6007-DB.vi ‏81 KB
MoteurGOTO.vi ‏87 KB
Commande_moteur.vi ‏10 KB

Similar Messages

How can I control 3 stepper motors w/ amplifier by sending TTL pulses from DIO96

We have NI PCI-DIO-96 board and we have 3 stepper motors with amplifier and encoders. We want to control the motors by sending TTL pulses directly from the DIO-96 board to the amplifiers. Is this possible? What would you recommend if this is not a good approach? Thanks in advance.
Roman Zeylikovich

Roman,
Thank you for contacting National Instruments. While using a motion controller would be the recommended approach for any type of motion application, you may be able to use your DIO board to generate a TTL pulse train to control the step and direction inputs of your drive and motor. You will need to make sure that the current sinking and sourcing specification for the DIO-96 fits your stepper motor. That board is not designed to source very much current at all so this is one issue you will need to verify. Also, this board does not have any counter/timer logic that can handle quadrature encoder inputs.
Again, this digital device is probably not the best solution to control a stepper motor, but, depending on your hardware, could be configured to work proper
ly. The PCI-7334 is a low-cost stepper motion controller that can control up to 4 axes and is designed to easily accommodate these types of applications. You can browse through more information on our Motion controller boards at the following website:
http://sine.ni.com/apps/we/nioc.vp?cid=3809〈=US
Let us know if you have any more questions or comments.
Regards,
Michael
Applications Engineer
National Instruments

How can I control 3 stepper motor in same time?

I want to control 3 stepper motor and 30 electro-valves.
I only had a few lessons on how to control one in C in college.
Now I need to do this in labview and using an board from NI
How can do the control of the three motors in same time?
What the best board to do this. Maybe the NI PCI 6034.
But I will need more than one?

At least some of the NI motor controller boards have up to 32 digital lines which can be set to input or output. I did not write the software for our systems but we are using quite a few of the digital lines for our systems and have no problems reading the digital inputs or setting the digital outputs. Also, the digital outputs offer a high current sink capability and usually can be used to drive external drives without any interface circuits.
The digital lines are available on a separate connector of the NI boards and there are also break-out boxes (with screw terminals) available. I do not see any serious problems to do your control tasks just with one NI motion controller board, as long as you do not have any special requirements (high sampling speed, high frequency pulse output etc) for the digital lines.

How can I control a stepper motor drive using a DAQ card?

I need to control a simple CW/CCW stepper motor drive using a DAQ
card. I simply need to output a 5 volt signal and then a drop in
the signal, and so on 200 times or steps for 1 revolution. I have
desiigned the basic program, but do not know how to output the
appropriate signal.
Cheers,
Matt

What DAQ card do you have? Ideally, one with a counter output to generate the steps, where you can control frequency. If you try to start the motor too fast (acceleration or abrupt application of fast pulses) it may stall out. Search in Help/Search for Examples for 'frequency' and 'pulse' for example of frequency generation. You can also use a digital output on the DAQ card to control direction.
If DAQ card does not have a counter, you coul do a software timed loop to toggle a digital output to generate the pulse train. It may not be fast enough nor accurate for your application, do not know from info you have given
~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~

How can I control a dc motor speed using an optical switch?

I am trying to use LabVIEW to create a VI that controls the speed of a DC motor. The system needs to have an user set rpm and the DC motor needs to adjust the duty cycle to obtain the correct rpm dependant on the load. A disk with holes and an optical switch is being used to measure rpm.
The current problem is that I cannot get the rpm based on the optical switch.
Thanks for your help!
Attachments:
Speed reg.vi ‏183 KB

The error for the samples to write does not appear after redoing the vi. Thanks. The controller seems to be working mostly.
However, the issue with the Tone Measurement reading inaccurately at low frequencies still exist. Any ideas?
I have attached the latest vi.
Thanks again!
Attachments:
speed_reg_v2013-05-07.vi ‏183 KB

How can I control stepping motor with PCI-7344 & UMI-7764? And I want to know the simplest circuit that I can do by myself?

Now I don't want to by commercial stepping motor driver, I want to do it by myself. I want to know the simplest driver circuit to drive and control my stepping motor (+5V 4 phases).

From the 7344's perspective, in open loop stepper mode, the only necessary outputs are the pulse train for steps and a TTL flag for direction. You can also set it for CW/CCW mode, which will output two separate pulse trains: one for clockwise motion, one for counter-clockwise motion.
If you only need to decode the signals into four phases and not amplify them above 5V, then a small IC might work for you (as long as you don't need a lot of current). A reconfigurable FPGA could be programmed to decode the incoming signal and output the four phases pretty easily. However, I honestly believe your best bet is just to buy a recommended amplifier for the motors.
Good Luck
Kyle V
Applications Engineer
National Instruments

How to control the step motor in this situation?

I have a PHI TRIFT3 ToF-SIMS instrument. The instrument comes with a default
software. However, the software don't offer fine step motor control. I want to control
the step motor using Labview.
I got some info from a Japanese engineer of the company.
The step motor controller is connect to a card in ISA slot. In the default software, I
can send command like D2000(distance 2000) and A100(acceleration 100) to "port 2"
to control the motor. I have a manual of the commands.
However, I don't know how to send command from Labview. Here is a joysticker
connected to COM1, COM2 is used for other vacuum control. The joysticker can also
control the motor..Here are some reply from the company about the control.
"We do not use special driver for control the step motor.
This is just sending the serial command via RS232C per command instruction I
sent you before. The only difference is, to simplify the hardware, we just talk to data acq
module(wave form card) via PAHOST card(installed in ISA bus slot of the PC)
to passthru the RS232C command to stepper motor control unit.
If you try to talk to step motor. just send the RS command from Labview
platform. (of course need to connect the step motor controller from PC,
default TRIFT PC does not have a spare COM channel, might be need to add
serial etension card or add the computer for Labview control)
"TRIFT PC passthru the RS232 command throught ISA bus to PHI data
acquisition box to stepper motor control.
Joystick handled by default software , convert to stage movement
command X and Y then send thru to ISA. "
I tried to use the Basic Serial Write and Read.vi to send command to COM1 but I always
get an error"1073807246 ocurred at property node(arg 1) in VISA configure Serial prot(Instr).vi->
Basic Serial Write and Read.vi Possible reason: VISA: the resource is valid, but VISA cannot access
it." I think this happens because the default software is also open and trying to control COM1.
What should I do to accomplish the step motor control? Thanks a lot

Just to start from scratch, have you verified that you can do basic communication with your serial port, ie successfully perform a loopback test? Please let me know, and we will go from there.
Logan S.

How can i control the motor movement of stepper motor using a NI PXI 7330

Good day to all,
i'm a newbie in programming in motion control of NI. I just want to ask if how can i control the clockwise and counter-clockwise rotation of a stepper motor using NI PXI 7330 module. all i can do is the counter-clockwise rotation using the example vi (Simple one-axis move.vi) found in the examples of LabView 2009.
Thanks

what type of limit switch sensor are you using and how did you wire itß What are your MAX settings regarding the limit switches?
Good day SIr Jochen,
I am using two reed switch for the reverse and forward limit. I wired the signal wire of the reed switch to the limit ports(forward and reverse Limit) and its ground to the digital ground of the UMI-7764.
the attachment below is the my max configuration about limit switches
Attachments:
max configuration.JPG ‏155 KB

How can I control an iPad from a touch screen which is mirroring the iPad screen

How can I control an iPad from a touch screen which is mirroring the iPad screen.
This is a very important application for disability students who wish to use iPad apps but do not have sufficient fine motor skills to use the small screen of an iPad but could use a large format display touch screen.
There must be a way.?????????? Help!!
Peter Niass
[email protected]

Have a look here
http://www.macstories.net/iphone/the-external-touchscreen-that-can-control-an-ip hone/

How can I disable speed step technology on my HP laptop?

hi all
I have DV7 1273cl hp laptop (Core 2 Duo 2.0 GHz CPU )
how can I disable speed step technology on my hp laptop ?
(I didn`t find CPU settings in BIOS , is there a special hotkey for CPU settings? )
thanks in advance

Hello krishna22211, welcome to the HP Forums.
I see that you're looking to disable the NVIDIA graphics. I will try to assist you with this.
Here is the latest BIOS update for your notebook :
HP Notebook System BIOS Update (Intel Processors).
If you update and the option is not there to disable/enable, to still try and minimize power consumption of the NVIDIA GPU, you could try any of the following:
Disable the drivers in Device Manager, or uninstall it.
Go into the NVIDIA control center and reduce the settings from in there.
Create a power custom power plan, that reduces power for graphics.
I hope this is able to help.
Thank you for posting on the HP Forums.
I worked on behalf of HP.

How can I control the workflow in the award the Rfx response

HI,Experts :
I work in SRM 7.0 ,RFx scenario .
In my case ,the supplier submit his RFX response according the RFX ,and the purchaser awards this response .
There are 3 steps workflow for one type RFX response,and 4 steps workflow for another RFX Response .So ,I know I just can use the standard transaction type for the RFX Response .SO ,How can I control the workflow in this case .
Bestregards
Alex

Hi,
If i understand your question correcly, you have to determine the process schema definition dynamically based on the transaction type.. then you can configure the process level ( 3 or 4 ) based the process schema definition..
Saravanan

How can i connect simple dc motor to labview

any one who help me how can i connect simple dc motor to labview and speed control of that

Hi,
There is a selection guide for motors on our website which can be found here: http://zone.ni.com/devzone/cda/tut/p/id/12594
There is also software specifically for LabVIEW to control motors. You can find it here: http://sine.ni.com/nips/cds/view/p/lang/en/nid/13851
Regards,
Greg H.
Applications Engineer
National Instruments

How can I control selection on a PDF

I have Acrobat Pro 9 Pro build 9.4.6 and am constantly exporting documents from indesign to .pdf, and also building docs in the 'combine' feature from mixed pages.
While everything seems to go reasonably well, I have a few problems that are due either to my ignorance, or bugs.
1. The biggie; How can I control what I select, for the purpose of copying, moving and deleting? When I drag the touch-up object tool over my selection, it selects what it wants to most of the time; sometimes it selects (i.e., puts a light blue box around) the entire page, instead of my selection (no pages are scanned). There are very few instances when I get exactly what I want; there are usually a few lines above or below, no matter how careful I am in my selection. The funny thing is that this is not a constant; sometimes, the tool works perfectly! and I have my heart in my mouth every time I really need it to work, hoping that it will not force me to go back to Indesign to make minor corrections. Perhaps my problems are connected to options I select when exporting my indds, but I've tried checking, clearing, and selecting various combinations and nothing seems to work.
Sometimes, the text selection tool is strange; a wide blue swath develops over the selected text, even though it is still usually possible to edit the text in this condition. And BTW, is there anything to do about the fact that some text can't be edited at all because a suitable font replacement can't be found? Can't a font be added somehow that will take care of this?
2. Headers and Footers; fairly effortless, but if the footer contains two rows and I want them centered, the second row looks centered in the preview but not in the doc. I have to go back to the footer dialog and guesstimate how many spaces to place before the second row to get it to look centered. Also, is there any way to place a logo in a header? That would be one of my requests for the next version of Acrobat, if not.
3.Hyperlinks; they don't always work,even though I check Hyperlinks in the Export settings. Sometimes yes, sometimes no.
4. Typwriter toolbar; it also seems to offer font and size changes whenever it feels like it, and I've tried all different orders of typing, selecting, etc.

It's me again, sorry! I wanted to save what I'd written, and my message popped up to the board.
Thank you for any advice anyone has!
PS My indd and acrobat are the same version, as they came in the same package (CS4). Windows XP sp3.
Oh, one more thing I just remembered, as long as I'm complaining; sometimes if I place an object (the logo) and copy it to another page, it disappears on the original page, as if I've cut it. Any fix for that? (strange how I can edit tmy 'reply' but not my original post...well, at least I found where to ask a question fairly quickly!)

How can I control the zoom on my mac mouse?

How can I control the zoom function on my mouse? In the middle of working on things my hand will rub the mouse by accident and all of a sudden the context within the screen is large. I have no idea of how to work this feature on my mouse and most times to get it to return to normal, I have to escape out of the work I am performing.

If you are pressing the "Control" button on the Mac keyboard, scrolling up will zoom in and scrolling down will zoom out. You can disable this if it annoys you through System Preferences > Universal Access. If you are using Mountain Lion, it would be System Preferences > Accessibility.
Uncheck the in the "Seeing" or "Zoom" section that says "Use scroll gesture with modifier keys to zoom". It may be slightly different if you have an older OS X version. I have Mountain Lion and am going off of memory on the older versions.

How can I control a button from one swf file to another swf file?

Hi,
I have a main.swf file. From that file I am accessing the external.swf file which is an external file.
Now, how can I write code on my main.swf file for the button which is on my external.swf file?
Activities.MainPanel.close_btn.addEventListener(MouseEvent.CLICK, btnClickClose);
Activities.MainPanel.close_btn (This buttons is actually on external.swf file, but I want to write code on main.swf file to execute it on external.swf) how can I control one swf button on other swf file?
Thanks.

Here's some example code that you should be able to adapt to your needs.
// create a new loader object instance...
var loader:Loader = new Loader();
// make the download request...
var request:URLRequest = new URLRequest("external.swf");
// add a complete event listener to the loader
loader.contentLoaderInfo.addEventListener(Event.COMPLETE, completeHandler);
// start the actual loading process...
loader.load(request);
// create a new empty movieClip instance, you will put the loaded movie into this movieClip once its loaded
var externalMovie:MovieClip;
// this function is called when the download has finished and the file is ready to use...
function completeHandler(event:Event):void {
   // set the contents of the loaded movie to the new empty movieClip...
           externalMovie = MovieClip(event.target.content);
   // add this new movie to the display list...
   addChild(externalMovie);
Now you can refer to the loaded movie with the instance name "externalMovie". So if, for instance, you want to address a button in the loaded movie, you could write something like this on the main timeline:
externalMovie.addEventListener(MouseEvent.CLICK, btnClickClose);
function btnClickClose(event:MouseEvent):void {

How can I control my step motor

Similar Messages

Maybe you are looking for