How can I find out what top level VI TestStand cannot find a sub-VI for?

I am trying diligently to build a TestStand deployment and keep getting errors. TestStand is telling me that an error has occurred because it cannot find a sub-VI in a certain path. The problem is it does not tell me what VI it cannot find a sub-VI for. It just gives me the path that it is trying to find the sub-VI in. Is there any way I can tell what top level VI in a sequence TestStand is trying to find the sub-VI for? Thanks in advance for any help.

Josh - I did not have any disbale diagram structures in the sub-VIs that were giving me trouble. Nor did I have any read only VIs. I mass compiled my entrire directory structure...twice. I had no choice but to go through every single sequence and open every VI. Once opened there were three that did not have the correct directory for a sub-VI and need saved. There were no errors due to a Labview mismatch. For some reason these three VIs did not save the sub-VIs new directory therefore causing trouble during my TestStand deployment build process. The thing I find odd about this is there are hundreds of other VIs that use these same sub-VIs in the same new directory that mass compiled fine. I am continuing my TestStand deployment build process and I will see how it goes from here. I definitely got further, after finding these three errros, than I have before. Thanks for the help.

Similar Messages

I see "imac-54f9d5" under the "Shared" heading in my finder. I am not connected to any printers or other Mac devices. Is it possible that someone is remotely accessing my system? How can I figure out what this is?

I see "imac-54f9d5" under the "Shared" heading in my finder. I am not connected to any printers or other Mac devices. Is it possible that someone is remotely accessing my system? How can I figure out what this is?

is it your imac?
is it your your router's name?
are you by any chance connected to another wifi router then your own because the other one was open and not password protected?

How can i figure out what device downloaded apps

how can i figure out what device downloaded certain apps?

One way is to remove all apps and then reinstall a few at a time while watching the "Other" memory indicator, but this will cause a loss of any data the apps are storing, like files, high scores, settings, etc.
I don't know of an 'electronic' way of find this out.

How can I programically make a top level VI panel invisible?

How can I programically make a top level VI panel invisible?

You can use VI Server's 'Close FP' method to close the front-panel. You will need a reference to that VI to invoke the method. One easy way is to launch the VI with the VI Server and hold on to its reference.
See the attached diagram -- the top-level.vi is launched and run, we wait for 5 seconds, and then close its front-panel.
Hope this gives you some ideas.
Khalid
Attachments:
close_fp.png ‏38 KB

How can you found out what computers you are home sharing so you can delete some, How can you found out what computers you are home sharing so you can delete some

How can you find out what computers you are sharing with so you can delete some

Oh, have you brought up so many good points. Not to take us off-topic, but I could rant all day about Eloqua consulting firms who let low-level employees (Eloqua skill-wise) loose on clients projects. Just not fair for either the employee or client. There was one company that did this to me a few years ago, and since then dozens of people have asked me about them for a reference. Needless to say, they never get a good one from me, and have likely lost hundreds of thousands of dollars in projects because of this. Not worth it in the long-run to cut corners.
Back to the topic at hand....
You really hit the nail on the head in so many ways. It really all does come down to one thing: hard work. There are no shortcuts. Always keep learning. Embrace every Eloqua challenge you can, and never say never. Never be fearful of being wrong by asking something 'silly', or 'looking stupid'. I remember several times that I've submitted Eloqua support tickets, or tickets to other related vendors about things that I was convinced were bugs/major issues. Turned out to be my mistake. But that's ok. You brush off, stand back up, and learn from them.
And finally, be modest. You will never know everything about Eloqua. Be willing to learn from others, and know that there actually may be a better way to do something than you may have spent days or weeks working on.

How can I figure out what my password is and keep it unlocked? Every time I do a system update, it requires the password and sends me into cyber trouble with the remember my keychain access, requiring it every time I log in. A real hassle to be avoided

How can I find out what my password on the computer is? I had to change it due to my teenagers helping themselves, and now every time there is a system update, I have to have the password, which I cannot remember or find. It then wants it every time I log in and pops up Key Chain Access as well. Very annoying. I do not have the disc to reload it and fear I would loose everything on my computer as there is also trouble with the back up system. Too many issues and not enough solutions. Many thanks in advance!

I do not have the disc to reload
Why not? You need your system dvds to troubleshoot & to reset/change passwords in view of your current OS listed in your profile.
You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
If you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number. Here's a list of links to all of those - http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html Another resource: International Support Phone #s.
===============
I have to have the password, which I cannot remember or find.
When selecting passwords, make sure it's one that you will NEVER forget AND no one else can figure out.
Old school--- > Print it out & keep in a safe place. A place that ONLY you know about AND never forget.
New school---> Get a password manager utility. Highly recommend 1Password which is shareware. Do a Google search for free password managers.

How can i figure out what my pin number is?

i need my pin number but don't remember what it is how can I figure this out?

josh0921, I know that being without your PIN can be quite the hassel. Just to be sure, are you referring to your billing account password or are you referring to a PIN used to unlock the device? If this is regarding your billing PIN when calling into customer service that cannot be changed, but can certainly be updated after completeing secondary verification over the phone. If you need to reach out customer service you can give them a call at 800-922-0204. http://vz.to/XNtW61
AdamG_VZW
Follow us on Twitter @VZWSupport

I have a two different charges for one album. How can I figure out what each charge is?

I purchased an album and got charged two different prices. How can I figure this out?

As has already been said, The onboard ethernet is 10/100/1000 and capable of autosensing which speed it's connected at.
What is more in question is the service you have. I don't remember if cable is the same, but with DSL, there are two connection methods.
1. IP Based. A static IP internet connection that is always on. Usually three things are required information that can be given via your ISP.
A) IP Address
B) Gateway
C) DNS Servers (Without these the PC cannot resolve DNS names so it doesn't know that http://www.website.com = xxx.xxx.xxx.xxx IP address.
You can get there by right clicking Network Neighborhood, and click PROPERTIES. Then right lick Local Area Connection and click PROPERTIES. You can click the TCP/IP setting and click the properties button and enter the proper information to get you online.
2. PPPoE (Point to Point Protocol Over Ethernet). PPPoE requires software from the ISP and usually all that is required is installation of the software and a USER NAME AND PASSWORD. IP, DNS, and Gateway are all auto-determined by the remote server that the PPPoE software connects to.
Does yours use one of these? Most people use a combination router/firewall and plug in either settings. If you've already configured your settings and are still getting no access, suggest the following:
a) Reset your cable-modem, then your PC and try again.
b) Check your cable connections. You may have an intermittent connection on your net card/wire. check the pins and look to make sure they make clean contact. Try another cable to make sure there are no broken/intermittent conductors in the cable.

HT201364 how can i found out what software my macbook has?

How can I find my software infromation on my mac book?

Do you mean operating system? See "About This Mac" in the Apple Menu.
Do you mean applications? See the Applications folder in your home root directory.
Edited for accuracy, thanks to Allan Eckert.

How can I reinstall CS6 on my laptop? I cannot find the download info.

I cannot find the download info on CS6. How can I reinstall CS6?

Download CS6 products
Download, install then enter your serial number.

HT1551 How can I view youtube directly on appletv. I cannot find an icon for it

How can I view YouTube directly on appletv, I cannot find an icon for it in the main menu

Open Finder Preferences, COMMAND ',' (comma). Check the boxes for the desired items.
Ciao

My macbook pro keeps freezing and shutting off when I am browsing the web on Safari. How can I figure out what is causing this issue?

For the past few weeks my computer will slow down when I have been on Safari for awhile, then freeze, and then just go black. I have to press the power button and then it goes to a black screen with the apple logo and a loading bar underneath when it reboots. I'm not sure what is causing the issue, but on my previous mac it would have an error message if something like this happened that I could submit. Any suggestions of where to start to solve this issue?
Thanks!

These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter "BOOT_TIME" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Select the BOOT_TIME log message that corresponds to the last boot time when you had the problem. Now clear the search box to reveal all messages. Select the ones logged before the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
For example, if the system was unresponsive or was failing to shut down for three minutes before you forced a restart, post the messages timestamped within three minutes before the boot time, not after. Please include the BOOT_TIME message at the end of the log extract—not at the beginning.
If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Some private information, such as your name, may appear in the log. Anonymize before posting.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Step 2
In the Console window, select
          DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". A shutdown stall report has a name that ends in ".shutdownstall". Select the most recent of each, if any. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot. It's possible that none of these reports exists.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

How can I even out the volume levels of my audio?

Hi,
I'm fairly new to FCE and to editing in general.
I've got a clip which contains a conversation, my camera is pointed at one of the speakers and their side of the conversation is significantly louder than the other.
Is there a filter I can use to make the loud side quieter and the quiet side louder in order to hear both sides of the conversation at roughly the same volume?
TIA,
Rob.

Hi Rob,
I asked a similar question recently, and though I ended up concluding the easiest thing was to just adjust the volume manually as Ian suggested, you can take a look at the suggestions I was given about possible filters and such here: http://discussions.apple.com/thread.jspa?threadID=1564173&tstart=0
Hope that helps; good luck!
Claire

How can I found out what was changed to fix a JDK bug?

For example I'd like to know what was changed to fix this bug: https://bugs.openjdk.java.net/browse/JDK-8064358

No idea. Impossible to speculate without more information.

How can i figure out what 'purchased items' i have not transferred...

Getting a message when i try to upgrade my iPad 2 to ios 6 "There are purchased items on the iPad “Becky’s iPad” that have not been transferred to your iTunes library. You should transfer these items to your iTunes library before updating this iPad. Are you sure you want to continue?" but i have done the manual backup... i see kindle books on my ipad i do not see in itunes, but i think i can just re-download them from Amazon...
Trying to be sure i do this upgrade without losing any apps or data!

is it your imac?
is it your your router's name?
are you by any chance connected to another wifi router then your own because the other one was open and not password protected?

How can I find out what top level VI TestStand cannot find a sub-VI for?

Similar Messages

Maybe you are looking for