How can I get my airport express work with Zyxel 2812HNU-F1?

Hi,
I previously had a Thompson Speedtouch router and my Airport expres worked just fine. But now my internetprovider give me a new router the Zyxel 2812HNU-F1 and my airport express doesn't work properly. I use an ethernetkabel to connect the airport express with my router. The lamp on the aiport express turns green, but I cannot normally open internetpages etc, and sometimes a webpage partially appears. If I connect my ethernetkabel in my MBP, the internetconnection just works normally.
Do you know what I have to do to let my Aiport expres work with the Zyxel 2812? I already resetted the express and in the airport utility it doesn't show that there is a problem.
Greets,
Don

Obviously my objective was different (just use the Airport Express as an Airplay speaker over wired ethernet only), but for my case I finally managed to fix it: In the Zyxel LAN configuration I've set the LAN port (4) to half-duplex and 10Mbit (only!) instead of "auto" and then streaming audio works flawlessly! This is just crazy stupid and is a Zyxel issue I'm sure. For now I'm happy!
To make the Airport wired only: disconnect wire -> factory reset -> create new (wireless) network (plus settings) -> then Network Router Mode = Off (Bridge Mode) -> then Disable wireless -> Save settings -> only then connect ethernet cable

Similar Messages

  • How can I get my AirPort to work with a newly purchased modem?

    I have a new AirPort that I purchased and linked to an older modem.  I now have a new modem, a NetGear provided my AT&T.  How can I transfer the new modem to work with the AirPort as seamlessly as possible?  I spend hours attempting the other night, but grew frustrated when the AirPort never communicated with the new modem.  Please help!

    Are you sure you are talking about replacing a modem? Modems are usually provided by your cable/DSL provider. So am I right in understanding you got a new modem installed by AT&T? If so, then you need to start by turning off the modem, the Airport router (what model, exactly?), and the computer. Wait one minute. The Airport router should be connected to the modem using an Ethernet cable. Now turn on in order:
    Modem - wait for status lights to show communication with your ISP.
    Airport - wait for the status light to start blinking amber.
    Computer - open Network preferences and select the type of connection port: Ethernet or Wi-Fi.
    Now at this point if the Airport device is still blinking amber, then open Airport Utility, click on the larger amber dot to find out what problem is being reported, then configure it to fix the issues.

  • How can I get the Airport Express to handle all the PPPoE stuff?

    Hi, I’m visiting my family in China, and now trying to help my dad, with his Airport Express and how to set up a PPPoE connection.
    We have currently set up the Airport Express in bridge mode (not distributing IP adresses and selecting DHCP under the Internet tab in admin utility). The Airport settings on our two computers is set up to connect using PPPoE using the given login name and password. (ps! we can not see the Base station in Airport Admin Utility when using these settings, we would have to select a new location from the Apple menu to see it and make condigurations.)
    What we want is to do, is to have the Airport Express connect to the ISP using a PPPoE connection and not through the computer.
    I know there is a 'Connect using PPPoE' option in Airport admin util, letting me input account name and password. If I select this setting instead of DHCP, enable distribution of IP addresses and configure my Airport card to NOT connect using PPPoE, I will see my base station in the Airport admin util with the IP address of 10.0.1.1 (or similar) and my computer will have x.x.x.2. Next to the Airport icon in the menubar, a scrolling message will say 'Looking for PPPoE host' without anything happen. I am sure my account name and password is correct as they've both worked when using this computer to connect to PPPoE (like now)
    How can I get the Airport Express to handle all the PPPoE stuff without using bridge mode?
    Ps! Both me and my dad have iPhones whom we can’t seem to get to connect unless its been distributed an IP address cause there's as fars as I know, no options of inputing a PPPoE user name and password.

    Any solutions to this? I'm in China also, in Beijing, trying to get my Airport Express to work with an ADSL modem.
    Direct ethernet cable connection to my Macbook works fine.
    When I configure the Airport Express with the ID and password that seems to be fine also – Airport Express shows a green light.
    But I cannot figure out the settings to connect wirelessly from my Macbook to the Airport Express. I get a constantly scolling message: "Looking for PPPoEhost..."
    thanks
    Paul

  • I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the Component and Audio ports on my TV?

    I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the MacBook Pro and connected to the TVs Component and Audio in ports.

    Will not work.  To my knowledge, dual converting like that isn't supported.  The Mac must detect the connected video output device and that sort of info cannot be done across an analog component uni-directional connection.

  • How can I get my ipod to work with itunes?

    When I connect my ipod classic into my new computer it seems that itunes does not recognize it. How can I get my ipod to work with itunes? I'm afraid to disconnect my ipod because the display is saying Do Not Disconnect.

    1. Update iTunes to the latest version. Plug in your iPod. If iTunes still can't recognize it, then in iTunes in the top left corner click help> run diagnostics. On the box that comes up, check the last two things. Click next and it should identify your iPod.
    2. Click on your windows start menu. Type in "services". Click on it and when it pops up, on the bottom of it click on "standard". Now Scroll down to find "Apple Mobile Device" Right click it when you see it and click on "Start". When it has started, close iTunes and replug in your iPod and it should show up.
    3. Check the USB cable
    4 Verify that Apple Mobile Device Support is installed
    5. Restart the Apple Mobile Device Service and verify that the Apple Mobile Device USB Driver is installed.
    6. If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job
    7. Check for third-party software conflicts.
    <Link Edited By Host>

  • How can I get elements 11 to work with 16 bits photos?

    In the expert mode of Photoshop Elements 11, I can only work with 8 bits photos. How can I get Elements 11 to work with 16 bits photos?

    No, you can still buy photoshop cs6 (perpetual license) if one doesn't want to subscribe to the cloud version (photoshop cc version 14)
    Either way is expensive compared to photoshop elements.
    http://www.adobe.com/products/cs6.html?promoid=JOLIS

  • How can I get photoshop CS2 to work with Windows 8.1?

    how can I get photoshop CS2 to work with Windows 8.1?

    Have a look at
    http://forums.adobe.com/message/4976720
    Cheers
    John

  • How can i get ical invitations to work with outlook users?

    how can i get ical invitations to work with outlook users?
    I can send ical meeting invitations but outlook users are having problems having the meeting show up in their calendar….

    My Epson is able to do scans using Image Capture without any problems at all.
    Allan

  • How can I get Phillips Fidelio to work with ios7

    How can I get Phillips Fidelio to work with ios7. It worked with the previous operating system

    Not sure if this is the same problem others are having, but I used to play music on my Philips Fidelio by opening the Music app on my ipad and clicking on the box with the triangle (which has now disappeared in the new OS). However, if you have the philips dockstudio app, the box still appears there and I was able to get my speakers working again.

  • How can I get my iMac to work with scanners?

    How can I get my iMac to work with scanners? The scanners scan just fine, but not to my iMac. I've tried Epson and HP all-in-ones; it makes no diffference. I'm becoming extremely displeased, but don't know at whom I should be displeased, the printer guys or Apple. Help?

    My Epson is able to do scans using Image Capture without any problems at all.
    Allan

  • HT4623 iPad 3 how can l gets the SIM card works With iPad 3

    As all we know its christmas time l just received the gift for iPad 3 &amp; l notice that it need SIM card for me to use as the phone &amp; data,how can l gets the SIM card works With iPad 3

    Remember am in South Africa &amp; we got few carrier nets am in MTN provide &amp; I c my sim looks so big to fit on my iPad

  • How can I get my Iphone to work with UCONNECT?

    How can I get my iphone 4s running IO7.0.4 to work with my UCONNECT system in my 2013 Chrysler?
    I have talked to UCONNECT and the tekkie said "you will have to live with it because your phone is too advanced for our software and we do not have an update planned."  I prress the "connect" button on the steering wheel and tell the phone to call a person on mobile.  I says it cannot call "somebody else" as they do not have a mobile number.  But the person it says is not the person I said. 
    It is like it is not reading the phonebook correctly.

    Everything worked perfectly until I updated to IO 7.  Then it went out the window.  I cnnot be the only person with this problem and hopefully someone out there has overcome this problem.  If you just stop at the first NO we would still be flipping our phones open.

  • How can I get full screen to work with utube in google chrome?

    When I use utube in google chrome I can not get full screen to work. How can I fix this?

    See: http://forums.adobe.com/thread/1193685
    also: http://helpx.adobe.com/flash-player/kb/enable-system-flash-player-google-chrome.html

  • How can I get interactive websites to work with Firefox?

    In the last week many of the interactive websites I've been using for years suddenly stopped working properly. However they do work with Internet Explorer. How can I get them to work again with Firefox?

    In what way are those websites not working?
    Clear the cache and the cookies from sites that cause problems.
    "Clear the Cache":
    *Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
    "Remove Cookies" from sites causing problems:
    *Firefox/Tools > Options > Privacy > Cookies: "Show Cookies"
    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
    *Do NOT click the Reset button on the Safe Mode start window or otherwise make changes.
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • How can I get a spyder2pro to work with Lion? Color vision says that Rosetta isn't compatible with Lion.

    How can I get updated software so my spyder2pro works on my MacBook Pro?

    You can get in touch with the Developers and see if they intend to release a version in the future which won't require Rosetta. Rosetta has been dropped in Lion. They make it quite clear on their site that Rosetta is a requirement, so I wouldn't hold my breath. That leaves you the option of finding a similar program which will run on Lion, or return to Snow Leopard, if they have no plans to make changes to their program in the future.
    Good Luck

Maybe you are looking for