How can I get my Boot Camp partition off my old drive?

I swapped out the stock 160gb drive that came in my MacBook Pro since it was acting up. I installed a new drive and restored it with Time Machine, but now my Boot Camp partition is still on my old drive. I slipped my old drive into a usb sata enclosure and tried booting from it in hope I could back it up with Winclone. When I went into the startup disk selector the drive would not show up (but it sounded like it was trying to spin up). Earlier when I pulled the drive out of my MacBook Pro it was still functioning fine, so I do not think the drive has failed.
Any ideas on how I can get the Boot Camp partition off the old drive? Thanks for your help.
-Ryan

Some drives require more current to spin-up from a "cold start" than most USB ports put out, even if the port supplies. Additionally, if the drive is failing, it may require even more power for the startup.
I have a couple USB enclosures with external AC power that I keep around in case I run into drives like this. Failing that, I also have a couple of USB cables which use 2 ports to provide additional current. Also the cable length, and gauge makes a difference.

Similar Messages

How do I write to my boot camp partition with Paragon NTFS that comes with Mountain Lion? Or how do I get my boot camp partition to show up in Paragon's "Available NTFS partitions:" panel like my external hard drive does?

I've just set up boot camp on my MacBookPro with a freshly installed Mountain Lion and Windows 7.
I would like to read and write in both directions from drive to drive if possible. I've hunted around quite a bit to try and work this out, and so far I understand that one can write to or transfer files from one drive to the other with Paragon NTFS among other softwares.
I noticed when I looked in my system preferences the utility "Paragon NTFS for Mac OS X" came with Mountain Lion and it will recognize an external hard drive when I have one plugged in under "Available NTFS partitions:". However, it does not automatically recognize my NTFS boot camp partition nor does it automatically give me write access.
Is the Paragon NTFS that comes with Mountain Lion limited in some way?
Do I still need to purchase and download the software of the same name from Paragon to get the full write privilidges I want or is there something I can do to get the version of Paragon on my MAC to recognize and give me write priviledges to my boot camp partition?
I'm open to all suggestions to get the read / write access between partitions in my boot camped drive.
MacFUSE is also listed in the System Preferences of my machine (it also came with Mountain Lion), if that helps. I'm still working out exactly what each of these is supposed to do and how I can use it to accomplish the task at hand.
My boot camp drive does appear normally in other contexts and in disk utility it indicates that the drive is mounted.
Thank you for any guidance you can give me.

Interesting. Comes with? you didn't have either before? Paragon is commercial and is now v. 10.0, they were the only one keeping updated and was supporting 10.7.4. I would not enable more than one.
For writing to HFS Paragon has theirs but probably give the nod to MacDrive there.
I never do an upgrade to a new OS over the old system, I backup (clone) and format the drive with the new OS and do the install so whatever is there I know is clean and also to keep from carrying around leftovers from years and systems past.
I would assme Paragon is limited. Try their site and knowledge base?
MacDrive
http://www.mediafour.com/updates/macdrive
Paragon HFS
http://www.paragon-software.com/home/hfs-windows/
Paragon NTFS
http://www.macupdate.com/app/mac/26288/ntfs-for-mac-os-x
http://www.paragon-software.com/home/ntfs-mac/

How can I get my bookmarks and mailboxes off my old iBook G4 that crashed?

My OS crashed. I reinstalled it, but still could not access anything. I took the computer to a repair person. He created a new account and retrieved everything I had on my desktop, but not my mailboxes or bookmarks. He said there is a way to do that, but it would be very expensive for me to have him do it. He said I could come here and find out. So here I am.
I can get online and to the desktop of this new account, but that's all. How can I get that stuff? I need it very badly.......
It was an iBook G4 14" with 10.4.11.
Thanks!

Here is what macjack has offered:
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh2316.html
Hope it works!

Can I erase the boot camp partition and dual boot snow leopard and mountain lion instead

Can I erase the boot camp partition and dual boot snow leopard and mountain lion instead

Please don't double post. Look at your other thread.
If you want to get rid of Windows and the BC partition use the Boot Camp assistant program to remove the Win/BC partition. Don't do it manually with Disk Utility Use the BC A program.

How can I get a boot-disk for a Compaq P2500 laptop Windows XP Home Edition?

I'm already in another forum with a eerily similar question, but that's for the HP Media Center Pavilion m8000e desktop system (Windows Vista Home Premium) I was just given; I've ordered a new hard drive for that. I assume the directions to create a boot disk with the *.iso file (using Imgburn) is going to work; I have the 25-digit code for that.
This question here now is for my wife's older Compaq P2500 2596US laptop running Windows XP Home Edition. This too needs a new hard drive, but I also am missing the boot disc for this; I do have the 25-digit product code.
How can I get a boot disk for this laptop? I tried the Ubuntu method outlined in a few posts; geez, what a headache ... never could get it managed. Does HP not make any boot disks available? Microsoft told me to check with HP.
I can furnish the product code; model #; serial# ... gee, maybe the oroginal receipt is even laying around somewhere ...
I need a boot disk to get the new hard drive up on board (if I end up ordering that).
Thanks for any help!
Michael

Hi
Please find the link given below might be helpful for your.
http://www.computersurgeons.com/productdetails.aspx?ID=4219
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

I'v got the latest macbook pro 13" and it dose not come with the lion os disk so how do i get the boot camp drivers for windows 7 without an os disk

i'v got the latest macbook pro 13" and it dose not come with the lion os disk so how do i get the boot camp drivers for windows 7 without an os disk

Page 5, step 2, #2, 2nd bullet.
http://manuals.info.apple.com/en/Boot_Camp_Install-Setup_10.7.pdf

Can i adjust the boot camp partition after xp install

can i adjust the boot camp partition after xp install

Hi,
Paragons CampTune http://www.paragon-software.com/home/camptune/ can do this.
Mac OSX and its BootCamp Assistant or Windows cannot.
Regards
Stefan

How can I get all of my music off of my laptop and onto an external hard drive? I bought a new hard drive for it but it got turned into a Time Machine drive...

how can I get all of my music off of my laptop and onto an external hard drive? I bought a new hard drive for it but it got turned into a Time Machine drive... I want to have all of my music on the external hard drive, and NOT on my macbook pro. Thanks everyone

Hello lramospsych,
To move your iTunes media library to a different location, take a look at the article below to walk you through that process. Make sure that you have everything organized before you move everything over.
iTunes for Mac: Moving your iTunes Media folder
http://support.apple.com/kb/ht1449
Regards,
-Norm G.

How can I get dock connector to turn off on air play. There is no longer a choice for sound to be displayed on iPad. I do not own outside speakers. Have already reset. Thanks

How can I get dock connector to turn off on air play. There is no longer a choice for sound to be displayed on iPad. I do not own outside speakers. Have already reset. Thanks

Slow, intermittent. Sometimes bootable sometime not. Odd behavior.
Sounds to me like a classic case of your HD failing.
Your SMART status may still show verified, with no errors on the Apple Hardware Test, Disk Utility shows no problems on Disk Repair- this is of no help.
I trust you have a good back-up and a bootable clone.
http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/

How can i get my fav or bookmakes from my old computer over to my new computer

how can i get my fav or bookmarks from my old computer over to my new computer

Hi,
Please [https://support.mozilla.com/en-US/questions/901979 see this.]
Useful links:
[https://support.mozilla.com/en-US/kb/Options%20window All about Tools > Options]
[http://kb.mozillazine.org/About:config Going beyond Tools > Options - about:config]
[http://kb.mozillazine.org/About:config_entries about:config Entries]
[https://addons.mozilla.org/en-US/firefox/addon/whats-that-preference/ What's That Preference? add-on] - Quickly decode about:config entries - After installation, go inside about:config, right-click any preference, enable (tick) MozillaZine Results to Panel and again right-click a pref and choose MozillaZine Reference to begin with.
[https://support.mozilla.com/en-US/kb/Keyboard%20shortcuts Keyboard Shortcuts]
[https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode]
[http://kb.mozillazine.org/Problematic_extensions Problematic Extensions/Add-ons]
[https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes Troubleshooting Extensions and Themes]

How can I get this function to fire off last?

In the following code, there are two buttons on the stage- "button1" and "button2".
I want to get the buttons to change frames and THEN have the "playerChange" function fire off.
Currently, the "playerChange" function fires first. Moving the function either renders the code inoperable or
returns error messages.
function buttonChange (e:MouseEvent)
{if
                (e.target.currentFrame == "frame1" )
         if (e.target==button1) (playerChange)
                 (e.target.gotoAndStop(player.currentFrame + 1))
           else{player.gotoAndStop(player.currentFrame)
          if (e.target==button2) (playerChange)
                (e.target.gotoAndStop(player.currentFrame + 1))
          else{player2.gotoAndStop(player2.currentFrame)
button1.addEventListener(MouseEvent.CLICK,buttonChange );
button2.addEventListener(MouseEvent.CLICK,buttonChange);
Note:this is an abridged version of the code. The code I'm actually using uses 20 buttons and about 8 conditionals for each button, so e.target is more convenient than writing a command for each button.

A: How can I get this function to fire off last?

the code is very hard to understand
it's badly formatted
{}'s don't match
you aren't calling a playerChange function
this is my guess at something that might work for you
function buttonChange (e:MouseEvent)
          if(e.target.currentFrame == "frame1" )
                    if (e.target == button1)
                              e.target.gotoAndStop(player.currentFrame + 1);
                              playerChange();
                    else
                              player.gotoAndStop(player.currentFrame);
                              if (e.target == button2)
                                        e.target.gotoAndStop(player.currentFrame + 1);
                                        playerChange();
                              else
                                        player2.gotoAndStop(player2.currentFrame)
button1.addEventListener(MouseEvent.CLICK,buttonChange );
button2.addEventListener(MouseEvent.CLICK, buttonChange);

Can no longer see Boot Camp Partition

Hello all,
I was having problems with booting into Boot Camp/Windows 7 (I was just getting a black screen), so I attempted to delete the boot camp partition and reinstall it. When I did that, the program hung for a while, and finally said there was an error deleting the partition. However, it appears it like halfway deleted it, as it no longer shows up! When I go into disk utility, Macintosh HD shows blue, and then there is a 50 GB partition (the size of my bootcamp) that is white, but it is unlabeled. I cannot adjust the partition to make it the whole HD, and if I go to boot camp assistant, and try to make a new bootcamp partition, it bounces back with an error message as well. I am wondering how I can restore the partition back to the original all mac hd partition..ANy help would be greatly appreciated!!
Kevin

WinClone 3 $20
When you move to a new OS: clone your system, make sure you have backups you can use - for each - the partition table "rules" change with each new OS. And you want to reformat a drive from time to time especially then.
Carbon Copy Cloner 3.4 is a good way to clone your OS X partitions.
Basically, "start over" and restore to one HFS volume with OS X then run Boot Camp Assistant, then restore with Winclone image you made easier.
www.apple.com/support/bootcamp
Find CCC and WinClone www.macupdate.com

How do I back up my Boot Camp partition to external firewire drive?

I have a 15 GB Windows XP Boot Camp partition (FAT32). I want to back it up to a 120 GB external Firewire drive. (I know the backup won't be bootable). In OX X Disk Utility, I formatted the external drive as MS-DOS (FAT). I planned to do the backup using the Windows Backup utility.
However, when booted into WinXP, Windows will not recognize the external hard drive. I thought I might need to create a FAT32 partion of 32 GB or less on the external drive, but I apparently can't do this in OS X or Windows (since Windows doesn't recognize the drive).
Any suggestions on how to backup the Boot Camp partition will be appreciated. I'm mainly interested in preserving all programs and data. Ideally, a clone could be created that could be restored back to the original partition in bootable form, but from studying this and other forums, it dosn't seem to be easy to do this for a FAT32-formatted volume.

My goal was to create a bootable clone of my FAT32 Boot Camp partition, while at the same time increasing the size of the partition from 15 GB to 32 GB if possible. This is what I did:
1. As suggested in this thread, I used Disk Utility to create a disk image. I formatted it as MS-DOS (FAT), and made it 32 GB in size.
2. Used the Finder to copy all files from my 15 GB Windows XP partition to the new disk image.
The following steps were only to determine if the disk image is a viable backup:
3. Removed the internal hard drive with my original Win XP partition, and installed a new internal hard drive.
4. Used Boot Camp Assistant to create a 32 GB Boot Camp partition on the new internal drive.
5. Inserted my Win XP installation disk and started the Windows installation. Formatted the new partition as FAT32. (I used the long rather than the quick format method--not sure if this was necessary.)
6. Continued the Windows installation to the point of restarting the computer, at which time I used the Option key to boot back into OS X.
7. Used the Finder to copy all the files from the 32 GB disk image to the new Boot Camp partition. (This overwrote a few Windows files installed by the aborted Win XP installation.)
8. Restarted and used the Option key to select the new 32 GB Boot Camp Partition. Windows booted as usual with all files, programs, etc. from the original 15 GB partition. Windows did complain about "new hardware" and required a restart, but all appears normal.
This indicates that the disk image containing all the files from my original Boot Camp partition is a viable backup, and can be used to restore the partition if necessary. I'm not sure if formatting the disk image as MS-DOS (rather than Mac OS extended) was necessary, or not.

How do I create a Boot Camp partition with Windows & blank NTFS partitions?

I'm trying to create this kind of setup:
OS X partition
Windows 7 partition
blank NTFS partition (no OS)
blank NTFS partition (no OS)
This would be much easier if I created just the OS X partition and the Windows 7 partition with the Boot Camp Assistant tool (done this many times before successfully on other computers). The problem begins when I try to split the Boot Camp partition through the Windows 7 DVD partition manager during setup by deleting the Boot Camp partition, and recreating three partitions from the unallocated space. After installing Windows 7 on one of those new three partitions, I'm getting all kinds of startup errors when I try to install the Boot Camp drivers.
What would the best way to achieve this setup?

Yes, I researched many options for three partition dual boot set ups. After many trials and tribulations, there is a simple method that I have used on multiple MBPs.
1. Run Boot Camp Assistant, as per the Boot Camp Installation and Setup Guide. Once you have Mac OS X and Windows 7 set up, check the partitions and back them up (with Time Machine, and Winclone).
2. Get iPartition, and resize the Mac and Windows partitions to what you want, say 100GB each, and set up your other partitions to the size you want. I put mine "after" the Windows partition, at the end of the disk, and have had no problems. It takes a few minutes to create the bootable CD for iPartition, but you get everything you need to do so from Coriolis Systems. You will need your Mac OS X installl disc.
3. Install Paragon's HFS+ for Windows and NTFS for Mac, and everybody can read and write everything.
4. I have both Time Machine and Norton 360 back up the Data partitions, just in case -- to an external drive, of course.
You can boot to either OS and access any partition.

Can you create a boot Camp partition on a Fusion Disk?

Can I install a BootCamp partition on a fusion disc?
Can I install a BootCamp partition (Wndows 7) on a 1 TB on which OSX mac Yosemite or Mavericks has been installed first? I have a 2012 MacBook Pro, that already has a 400 GB Boot Camp partition, but I am considering replacing it with a fusion disc or an SSD since I shall have to install a windows compatible medical dictation application that could use a speedier disc. Will Mac OS and Windows interfere with each other on the SSDpart of a large fusion disc ( 1 TB) if I switch back and forth from rebooting on Mac OS , then on Windows and vice-versa? Does the SSD part of the fusion disc get confused, and will the fusion disc tolerate the installation pf a Boot Camp partition in the first place, or just give a stretch of plain 5400 RPM disc without the SSD part ?Can I

1. On single-disk Macs, you can use an SSHD (as a single physical disk), but not an SSD/HDD. There is a no single physical unit which is a Fusion drive. A Fusion drive consists of a physical SSD and a physical HDD. MBPs on which the Optibay has an SSD/HDD and main bay with SSD/HDD will support a Fusion (aka CoreStorage volume). Yosemite supports a Fusion drive, which has an internal SSD and and external HDD (the reverse makes no sense, but is possible).
2. On newer Macs, with 1TB PCIe flash, you have an SSD as your whole drive.
3. The two environments, OS X and Windows are self-contained, on separate partitions. The underlying hardware is common.
4. On a Mini, which supports two drives, I have a 256g SSD/1TB HDD, in a DIY Fusion drive, with Windows on the SSD part. Bootcamp Assistant does not support this, but third-party tools can be used. The other option is to install OS X and Windows on a SSD, and later add an HDD and include into a CS volume. This is what I would recommend for you.
5. The 13-in 2012 MBP will allow you use a USB installer, without the need for an Optical drive, so it is possible to replace the Optibay with an HDD, create a Fusion drive. If BCA is used, it will put Windows on the HDD on this specific machine if the Fusion drive is created first.

How can I get my Boot Camp partition off my old drive?

Similar Messages

Maybe you are looking for