How can I join 2 .wav files?

I need to join 2 short .wav files for a web site.
How do I do it and what do I need.
thanks for any help.

WAV can hold audio in both compressed and uncompressed format. [http://en.wikipedia.org/wiki/WAV] The optimal way for joining the files will depend upon the format of the audio format contained in the WAV and the format of the output desired. For general audio I'd go with an audio editor such as Audacity or Amadeus Pro. There are also [scripts for itunes|http://dougscripts.com/itunes/itinfo/jointogether.php] that do this kind of thing, though more restricted in output. If the audio content is mp3 compressed you can use an editor such as MP3 Trimmer to do this without recoding the audio which results in better quality.

Similar Messages

How do I compress Wav files

Hi, I have some sound files that I want to be able to email to people, but I can't because the files are too big. Is there a way to compress these files(wav)?

You may refer to the following there method to compress WAV files
Method 1: Compress WAV to other audio format
Compress WAV to lossless compression audio format without losing audio quality like compress WAV to FLAC, compress WAV to Apple Lossless ALAC M4A
Compress WAV to lossy audio format like compress WAV to MP3, compress WAV to WMA, AAC, RA and etc.
Method 2: Lower WAV bit rate
With this method, we can easily reduce WAV file size without changing WAV audio format.
The lower the bit rate, the smaller the WAV file size, the lower quality of the WAV audio.
In most cases, WAV audio quality shows little difference between 128kbps and higher bitrates. WAV quality will become crappier if the bit rate is less than 128kbps.
Method 3: Compress WAV to other audio format as well as lower bit rate
The third way to compress a WAV file size is that we simultaneously apply Method 1 as well as Method 2.
Resources: How to Compress WAV File Size without Losing Quality on Windows or Mac?

How to play a wave file through the DAQ board?

Hi there,
we want to play a wave file that is saved on the harddrive via the DAQ board. Means we want to connect a amp to the analog output of the DAQ to amplify the sound and play it through a speaker.
We couldn't find any VI that does that. Can anybody tell us how to play a wave file, or perhaps even send us a VI that can do that?
Thanks a lot for your help
Martin - Physical Optics Corporation

Hi Martin,
The only example that I could find on how to do this was using our
older Traditional DAQ drivers version 6.9.3. If you're using Traditional
DAQ drivers, the vi can be found here.
The example reads a 8-bit mono .wav file (an example .wav file is included in the .zip file) and writes it to the analog out of your DAQ card. I've updated the
example to work with our newer DAQmx drivers and attached it here.
I hope this helps,
Paul C.
Message Edited by Paul C. on 08-14-2007 05:47 PM
Attachments:
daqmx_wav_file_to_ao_output.zip ‏27 KB

How can I join up my home videos in order to see them together rather than in short bursts? IN SIMPLE TERMS PLEASE.

How can I join up my home videos in order to see them together, rather than in short bursts? In simple terms please?!

You can research into the iMovie app and see what it'll do. I'm afraid I've never used it. But I know it does have a section on this forum so maybe someone there can answer your question.
The only other way I can think of would be to get your files off your iPad and onto a computer and then get a video editing program (there are several that are inexpensive) and use that to put them together.

Can iPod play WAV files

I have the All Music Converter and have converted some of my iPod music files to WAV. However, I can't get iTunes to accept the files. Can iPod play WAV files? Does anyone know how to get them to transfer into iTunes? Thank you.

Uncompressed WAV files are on the list of compatible formats, has there been any compression applied to the files you have converted?
iPod 101: Which Files Work With iPod and iTunes
iPod: About compatible song formats
iPod shuffle: Compatible audio formats

How can I play mkv files in iTunes?

Hi All,
How can I play mkv files in iTunes?
What're the limitations of iTunes? I see there are a lot of files that iTunes cant play. Is it true for all?
Lofty

BUT my iMac does not support my WAVE files
Sure it does.
File -> Add to library and select the folder where the WAV files are located.

How can I copy mp3 files from my Itunes library to an SD card for use in a non-apple phone?

How can I copy mp3 files from my Itunes library to an SD card for use in a non-apple phone? I can physically copy the tunes as mp3's but the phone does not seem to be able to play all of them. Do I need to copy an entire album or can I just pick & choose individual songs? The phone is question is an LG running who knows what for an operating system.

AAC is Advanced Audio Coding. Basically it's a format that sounds better than MP3 but doesn't take up as much space as a lossless format (like you'd have on a CD). More than likely you've had that encoding turned on when you ripped your music into itunes (it's the default encoder). Therefore your LG phone won't play them.
You need to turn off the AAC format by going to the iTunes menu, Preferences, General (at the top), then clicking the "Import Preferences" button. Change the AAC Encoder to MP3 Encoder. After that you'll have to make MP3 copies of your songs by right clicking them and selecting "Create MP3 Version." You'll get a copy of the song that should transfer to your SD card and have MP3 encoding. Hopefully your phone will play that.

How can I delete a file from Adobe Acrobat Reader DC?

How can I delete a file from Adobe Acrobat Reader DC?

What operating system do you use? Where do you store the files?

I have sent a file to the trash bin. When I come to empty the trash bin everything goes out except this one particular file and I get a note saying the file is 'in use' but it is not. How can I delete this file from trash?

I have a Macbook Pro with OS X Lion 10.7.2. I have sent a work file to the trash bin along with many other files. When I empty the trash this one particular file remains and I get a message that this file is still in use. I have tried returning the file to my documents, opening it, closing it and then sending it to trash and again I try to empty trash but the same message comes up - Q - How can I trash this file permanently?

First just try logging out and back in. Whatever is holding on to it may not be running after the logout thus freeing it so you can trash it after logging back in.
You might also try Trash It!
Lastly, look at the following for suggestions:
The X Lab: Solving Trash Problems

How can I bring a file from a folder on my desktop to this program and make it editable. Like deleti

How can I bring a file from a folder on my desk top int this program and make it editable., in order to replace words or remove words or texts..? jn

Hi,
FormsCentral cannot be used to edit existing PDF documents. That functionality is available in Adobe Acrobat:
http://www.adobe.com/products/acrobat.html
Regards,
Brian

I downloaded an Adobe file from my email but cannot find it on my hard drive or in recycle bin - it's in downloads but am unable to open from downloads - how can I recover the file?

I downloaded an Adobe file from my email (service provider is MWeb) but now cannot find it on my hard drive and it's not in the recycle bin. It does, however, appear in Firefox downloads but I'm unable to open it from there. How can I recover the file?

Thanks Rob.
I actually had no clue what the core problem was caused by. So it's Windows itself...that helps some.
I'll resubmit there. It might actually have saved time for it to simply have been moved to there instead of off-topic, though I suppose you have to follow protocol.

How can I save a file using In Design 6.0 and open it in 5.5

We have Creative Suite 6.0 and 5.5. How can we read a file created using In Design 6.0 on another computer that has version 5.5?

The file needs to be saved to IDML from CS6.
Mylenium

How can i print my files from mi iphone 5 throught the airport express?

How can i print my files from mi iphone 5 throught the airport express?? i have the last iOS version installed and also the last firmware version of the printer. the printer is already connected to the USB airport express and when i look for printers in airprinter there is no printer found. i have an HP LASERJET P1606dn(i think that is supported by the airprinter).

In order to function with AirPrint, a printer must connect to the network wirelessly.
Even if you have an AirPrint compatible printer, iOS devices will not be able to print to the printer when it is connected via USB.
So, you have two options:
1) Reconfigure the printer to connect to the network using wireless only and the iOS devices should be able to print that way....assuming that you have up to date drivers for the printer installed.
2) Leave the printer connected via USB and then use a third party App like Printopia installed on your Mac as a "workaround" to (hopefully) allow the iOS to device to be able to print. If you want to give this a try, there is a free trial for Printopia, so you will know if it will work before you buy. You must have a Mac running on the network in order for Printopia to function correctly.
Printopia - AirPrint to Any Printer - Print from iPad - Print from iPhone ...

How can I convert multiple files at one time and not one at a time

How can I convert multiple files at one time and not one at a time

Hi Plissey1950,
Sorry for the lengthy delay to a response. Are you trying to convert multiple files to individual PDF files at the same time? (not combine them). If so, you'll need to use Adobe Acrobat for this function. The CreatePDF service does not have the ability to convert multiple files to multiple individual PDF files.
Thanks,
David

How can I assign image file name from Main() class

I am trying to create library class which will be accessed and used by different applications (with different image files to be assigned). So, what image file to call should be determined by and in the Main class.
Here is the Main class
import org.me.lib.MyJNIWindowClass;
public class Main {
public Main() {
public static void main(String[] args) {
MyJNIWindowClass mw = new MyJNIWindowClass();
mw.s = "clock.gif";
And here is the library class
package org.me.lib;
public class MyJNIWindowClass {
public String s;
ImageIcon image = new ImageIcon("C:/Documents and Settings/Administrator/Desktop/" + s);
public MyJNIWindowClass() {
JLabel jl = new JLabel(image);
JFrame jf = new JFrame();
jf.add(jl);
jf.setVisible(true);
jf.pack();
I do understand that when I am making reference from main() method to MyJNIWindowClass() s first initialized to null and that is why clock could not be seen but how can I assign image file name from Main() class for library class without creating reference to Main() from MyJNIWindowClass()? As I said, I want this library class being accessed from different applications (means different Main() classes).
Thank you.

Your problem is one of timing. Consider this simple example.
public class Example {
    public String s;
    private String message = "Hello, " + s;
    public String toString() {
        return message;
    public static void main(String[] args) {
        Example ex = new Example();
        ex.s = "world";
        System.out.println(ex.toString());
}When this code is executed, the following happens in order:
1. new Example() is executed, causing an object to constructed. In particular:
2. field s is given value null (since no value is explicitly assigned.
3. field message is given value "Hello, null"
4. Back in method main, field s is now given value "world", but that
doesn't change message.
5. Finally, "Hello, null" is output.
The following fixes the above example:
public class Example {
    private String message;
    public Example(String name) {
        message = "Hello, " + name;
    public String toString() {
        return message;
    public static void main(String[] args) {
        Example ex = new Example("world");
        System.out.println(ex.toString());
}

How can i wrote configuration file in Log4j

iam new log4j .i have seen one small programme in log4j examples folder ..i e. shown below
Sort.java
=====
package examples;
import org.apache.log4j.PropertyConfigurator;
import org.apache.log4j.Logger;
import org.apache.log4j.Priority;
Example code for log4j to viewed in conjunction with the {@link
examples.SortAlgo SortAlgo} class.
This program expects a configuration file name as its first
argument, and the size of the array to sort as the second and last
argument. See its source
code for more details.
Play around with different values in the configuration file and
watch the changing behavior.
Example configuration files can be found in <a
href="doc-files/sort1.properties">sort1.properties</a>, <a
href="doc-files/sort2.properties">sort2.properties</a>, <a
href="doc-files/sort3.properties">sort3.properties</a> and <a
href="doc-files/sort4.properties">sort4.properties</a> are supplied with the
package.
If you are also interested in logging performance, then have
look at the {@link org.apache.log4j.performance.Logging} class.
@author Ceki Gülcü */
public class Sort {
static Logger logger = Logger.getLogger(Sort.class.getName());
public static void main(String[] args) {
 if(args.length != 2) {
 usage("Incorrect number of parameters.");
 int arraySize = -1;
try {
 arraySize = Integer.valueOf(args[1]).intValue();
 if(arraySize <= 0)
 usage("Negative array size.");
catch(java.lang.NumberFormatException e) {
usage("Could not number format ["+args[1]+"].");
PropertyConfigurator.configure(args[0]);
int[] intArray = new int[arraySize];
logger.info("Populating an array of " + arraySize + " elements in" +" reverse order.");
for(int i = arraySize -1 ; i >= 0; i--) {
 intArray[i] = arraySize - i - 1;
SortAlgo sa1 = new SortAlgo(intArray);
sa1.bubbleSort();
sa1.dump();
// We intentionally initilize sa2 with null.
SortAlgo sa2 = new SortAlgo(null);
logger.info("The next log statement should be an error message.");
sa2.dump();
logger.info("Exiting main method.");
static void usage(String errMsg) {
 System.err.println(errMsg);
 System.err.println("\nUsage: java org.apache.examples.Sort " + "configFile ARRAY_SIZE\n"+
"where configFile is a configuration file\n"+" ARRAY_SIZE is a positive integer.\n");
System.exit(1);
and
SortAlgo.java
==========
package examples;
import org.apache.log4j.Category;
import org.apache.log4j.NDC;
Example code for log4j to viewed in conjunction with the {@link
examples.Sort Sort} class.
SortAlgo uses the bubble sort algorithm to sort an integer
array. See also its source
code.
@author Ceki Gülcü */
public class SortAlgo {
final static String className = SortAlgo.class.getName();
final static Category CAT = Category.getInstance(className);
final static Category OUTER = Category.getInstance(className + ".OUTER");
final static Category INNER = Category.getInstance(className + ".INNER");
final static Category DUMP = Category.getInstance(className + ".DUMP");
final static Category SWAP = Category.getInstance(className + ".SWAP");
int[] intArray;
SortAlgo(int[] intArray) {
this.intArray = intArray;
void bubbleSort() {
CAT.info( "Entered the sort method.");
for(int i = intArray.length -1; i >= 0 ; i--) {
NDC.push("i=" + i);
OUTER.debug("in outer loop.");
for(int j = 0; j < i; j++) {
 NDC.push("j=" + j);
 // It is poor practice to ship code with log staments in tight loops.
 // We do it anyway in this example.
 INNER.debug( "in inner loop.");
if(intArray[j] > intArray[j+1])
 swap(j, j+1);
 NDC.pop();
NDC.pop();
void dump() {
if(! (this.intArray instanceof int[])) {
DUMP.error("Tried to dump an uninitialized array.");
return;
DUMP.info("Dump of integer array:");
for(int i = 0; i < this.intArray.length; i++) {
DUMP.info("Element [" + i + "]=" + this.intArray);
void swap(int l, int r) {
// It is poor practice to ship code with log staments in tight
// loops or code called potentially millions of times.
SWAP.debug( "Swapping intArray["+l+"]=" + intArray[l] +
 " and intArray["+r+"]=" + intArray[r]);
int temp = this.intArray[l];
this.intArray[l] = this.intArray[r];
this.intArray[r] = temp;
This program expects a configuration file name as its first
argument, and the size of the array to sort as the second and last
argument. See its source
code for more details.
please help me how can write that configuration file
thanks

Hi bala,
check that log4j manual I pointed to in yer previous thread.
This is a pot-boiler config file... Copy it into some file say "props.conf" and use it.
# Set root logger level to DEBUG and its only appender to A1.
log4j.rootLogger=DEBUG, A1
# A1 is set to be a ConsoleAppender.
log4j.appender.A1=org.apache.log4j.ConsoleAppender
# A1 uses PatternLayout.
log4j.appender.A1.layout=org.apache.log4j.PatternLayout
log4j.appender.A1.layout.ConversionPattern=%-4r [%t] %-5p %c %x - %m%nCheers,

How can I join 2 .wav files?

Similar Messages

Maybe you are looking for