How can I repair Canon Pixma MP550 Error B200?
How can I repair a Canon Pixma MP550 error 200?
Hi dlp1962uva,
Welcome to the Apple Support Communities!
I understand you are trying to install your Canon printer after replacing your hard drive on your MacBook Pro. It sounds like you have done some great troubleshooting by trying to install the drivers. I did some research on your printer, the Canon PIXMA iP6000D and it appears that this printer software is no longer available through software update.
OS X: Printer and scanner software available for download
http://support.apple.com/kb/ht3669
Additional Information
Printer software no longer available through Software Update
The third-party vendor no longer provides software for the following models to download and install through Software Update. Contact the vendor or visit their website for further assistance.
The The Additional Information section where I found this information is at the very bottom of this article. This printer specifically is listed as a printer that is no longer supported by software update is the list under Additional Information. I would suggest contacting Canon to see if the printer drivers are still available through them.
I hope this helps,
-Joe
Similar Messages
-
Hi,
When I turn on my printer it give me B200 error. A week ago I disconnected supply cable for 12 hours and it go well.
Now I tried to disconnected already for 12 hours but this time it don't go.
I I replaced all cartridges, clean printer head with water and dry it, but it don't go.
I tried to go in service mode and green and orange led flashing alternatively. If I try to press resume 4 times in service mode to reset ink waste, nothing happens.
Advice???*** DISCLAIMER *** You'll try the following advices solely on your own responsibility!
After B200 error in my MP640 (Europe version) I firstly carried out a print head cleaning method with alcohol and distilled water (6 + 6 min) proposed at [link removed per forum guidelines] (see down on the page and use Google translate if needed).
Well, cleaning alone didn't help.
After that I found from another forum an 'open print head bay boot' (like I'm calling it...) trick which I combined with an idea of nozzle cleaning. So I managed to solve my B200 problem as follows:
1. Turn OFF the printer and make sure there is plenty of ink left in every tank.
2. From "Devices and Printers" open MP640 properties and further the "Maintenance" window.
3. From Maintenance section select nozzle cleaning (all colors), preferably the 'deeper' one. And then STOP! Don't start any cycle yet.
4. Open the print head bay (as though you were about to change inks).
5. Turn ON power.
6. Wait for print carriage to start moving to the left and let it go past half way.
7. Before print carriage reaches left hand side (but after going halfway across) shut the cover.
8. Printer's display turns now into dark color and shows text "Canon" above the 'running balls'. During that time start the cleaning cycle but don't do anything else, i.e. don't try to print the test page yet.
9. Nozzle cleaning should start right after printer initializing.
10. After the cleaning cycle is finished run another one without printing anything. Make sure you don't run out of any ink.
11. Print the test page to check if additional cleaning is still needed.
I had to do the print bay boot + nozzle cleaning another time because B200 error returned quite soon after the first try. But after some more cleaning cycles and printing everything seems to be ok now. Hope this helps with your printer! -
Im experiments a 1436 error And I want know how can I repair it. Is my hardware a classic ipod 80 gb?
Try this support article > iPod: Cannot restore or update in iTunes with error 1415, 1417, 1418, 1428, 1429, 1430, 1436, or 1439
-
Mail application keeps shutting down short after start up - resulting in an error message. how can I repair what is wrong without losing my mail history?
Will I lose my emails I have on there? I have numerous client email files and can't afford to lose any of them. I do have everything backed up but I'm fearful of losing important client info. What if something happened during the back up and it doesn't have my files?
-
I updated iTunes to 10.4 version and now it doesn't start and send a messages "iTunes has detected an error and must be closed". Someone have the same problem and how can we repair our installation insted of change the windows XP installation? Best regards
Only way to get iMac starting again was to re-install 10.4.4 from DVD, and then update it into 10.4.6. For a while it worked perfectly, just as before.
Then I tried to print to CD with my EPSON Stylus Photo 950 from Adobe Photoshop Elements (2.0). It didn't print anything, but printer started flashing all lights. The print job was not performed, so I did remove it from the Printer Utility. After that the iMac started "ticking" again, same noise than before, after 10.4.7 installation. I did re-boot iMac. It never started, it does stuck on gray screen (gray block running clockwise). HW test from DVD didn't find any problems (extended search looping 3 times). But Disk Utility found hard drive to have inaccurate node structure, it could not fix it.
Apple support recommended to use DiskWarrior. However, it does not support (yet) Intel Macs. I haven't got TechTool Pro 4.5.1 anywhere. iMac does start on to FireWire mode (T at boot), but I cannot see the disk from 10.2.8 iMac.
So, obvisously the problem is not 10.4.7. I believe it to be ESPON printer driver compatibility on Mac OSX. This does not suprise me, EPSON printers *****, I shall never purchase one again. However, disk catalog structure should not get messed by one faulty printer driver! -
OhhHH my God error 1013 how can I repair it realy bothering me??
OhhHH my God error 1013 how can I repair it realy bothering me??
Error 1004 and 1013: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to default on Windows. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
Try to restore from another known-good computer and network.
If the errors persist on another computer, the device may need service.
http://support.apple.com/kb/TS3694#error1013 -
PSD files corrupted, How can i repair it?
Hi,i have 3 .PSD files corrupted, How can i repair it? when i try to open it , appear this message " it is not a valid Photoshop document."
Work File Safety | Mylenium's Error Code Database
Mylenium -
How can I repair Safari 8.0.2?
How can I repair Safari 8.0.2? it will not reopen after closing unexpectedly. I have a Macbook Air. I checked plugins etc in my library. I keep getting the error message and when i click reopen, nothing happens. I have rebooted as well.
Genieo Adware is installed. Removing it will help.
If you have another browser installed, use it.
If not, launch App store and get another browser for temporary use.
Remove it afterwards.
1. Use free AdwareMedic by clicking “Download ” from here
http://www.adwaremedic.com/index.php
Install , open, and run it by clicking “Scan for Adware” button to remove adware.
Once done, quit AdwareMedic by clicking AdwareMedic in the menu bar and selecting
“Quit AdwareMedic”.
or
Remove the adware manually by following the “HowTo” from Apple.
http://support.apple.com/en-us/HT203987
2. Safari > Preferences > Extensions
Turn those off and relaunch Safari to test .
Turn those on one by one and test. -
Hi,
How can I repair my hard disk. Computer Starts up and then shuts down.
I've started up with the CD and disk utilities can not fix the disk, invalid node error.
How can I fix my disk?
I need to get to the file on the hard disk.
Thanks
PeterWith Disk Warrior can I start with a CD/DVD and get at the files on the hard disk?
With apple disk utilites I can not see my files that are on the hard disk.
If I could get at my files I could back them up and reformat my hard disk. -
How can I repair problem 42110 in iTunes?
How can I repair problem 42110 in iTunes?
Try the following user tip:
iTunes for Windows 11.0.2.25 and 11.0.2.26: "Unknown error -42110" messages when launching iTunes -
My IMac G5,(late model '04) was not working as expected. I verified the permissions, and a few were repaired. The problem continued, then I verified the disk(Tiger).
The process returned a message box with the following text: "First Aid Failed. Disk utility stopped because the following error was encountered: The underlying task reported failure on exit".
There are 2 message indicating the "Volume bit map needs minor repair" and "the 1HFS volume checked needs repair"
The clickable button that should be pressed to perform this repair is grayed out and non functional.
How can I repair this disk?
Re Hard drive specs:
ST380013AS:
Capacity: 74.53 GB
Model: ST380013AS
Revision: 3.42
Serial Number: 5MR6P2DG
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Tiger:
Capacity: 74.41 GB
Available: 46.94 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s3
Mount Point: /Yes, you cannot repair the Disk while booted from the same one.
"Try Disk Utility
1. Insert the Mac OS X Tiger Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
In the future... you do not want to Repair Permissions or do any writing the the HD if it needs repair. -
How can I repair damaged pdf files?
I have several hundreds of damaged pdf files and want to repair them. I need to know how to repair them, for example with a software!
Hello Sukrit,
thank you for your reply!
I have deleted the PDF Files and needed to recover them. The size will be shown, but I can't open all of them.
I would like to recover them again or change them again to PDF files, if possible.
With regards,
Stephan
Von meinem iPad gesendet
Am 24.04.2015 um 15:41 schrieb "sukritd15" <[email protected]>:
How can I repair damaged pdf files?
created by sukritd15 in PDF Forms - View the full discussion
Hi Stephan ,
Acrobat is capable of repairing the damaged PDF' ,however it depends on the requirement as to how do you want to repair them.
There could be several reasons that can damage a PDF.
We need to know the cause that has damaged those PDF' and how exactly you want to repair them in order to assist you accordingly .
Regards
Sukrit Dhingra
If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7474818#7474818 and clicking ‘Correct’ below the answer
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7474818#7474818
To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
Start a new discussion in PDF Forms by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624. -
I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! Why is this a problem and how can i repair it?
"I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! ":
That is correct.
"Why is this a problem and how can i repair it?"
Becasue this has never been a feature of iphone/ipod/ipad. There is nothing to repair. -
How can I throw a hard 404 error to apache when a JSP is not found.
How can I throw a hard 404 error to apache when a JSP is not found.
I want to let apache handle the error.[email protected] (Jeremy Conner) wrote in
<[email protected]>:
>How can I throw a hard 404 error to apache when a JSP is not found.
>I want to let apache handle the error.
>
>
First thought that comes to mind is to return HTML that tells the browser
redirect to a nonexistent file under Apache. You can't tell Apache to
throw a 404 unless you're in a mod. Maybe something they could add to the
proxy, but until then, I think a redirection in the response HTML is your
only option.
Jesse
-
How Can I Fix A QuickTime Codec Error?
How Can I Fix A QuickTime Codec Error?
I have several movies from 2008 that are labeled as .mov but I now get a QuickTime error saying "The document "XXXXXX" could not be opened. A required Codec isn't available."
These movies ran in QuickTime just fine until about a month ago.
All the folders in which these movies were stored in 4 folders in 2 folders in one folder. All folders at each level were encrypted with Stuffit Deluxe a version circa 2008 and decrypted with a newer Stuffit Deluxe 10.x. Other movies that are NOT .mov and in with the .mov movies still run.
If I click on the Thumbnail Preview "It" runs.
How can I fix this?
TOP image is the Error message.
BOTTOM image is the Thumbnail Preview info.
I've checked out "Tell Me More" and have not found a solution.How Can I Fix A QuickTime Codec Error?
The basic work flow is to determine which codecs were used to create the non-playing file and then check to see if these formats are supported by your current system codec component configuration.
If the files will open in one of the QT player app, the open the inspector window to see which codecs were used to create the original file as seen here...
or here in the "Format" entry...
Or, if you have QT 7 keyed for "Pro" use, you can open the "Properties" window to gain even more information as demonstrated here...
if you file will not open in either of the QT Player apps, then you can try opening the Finder "Get Info" window for the file,
use a third-party media player that will open the file, or
use a dedicated media information utility to learn this information....
Once you know what codecs were used to create the file, post back with this information so we can deterine if the file should be natively supported by your Mac OS X install, requires an Apple Pro editing codec normally installed by the editor app, or requires a third-party codec which the user must supply.
These movies ran in QuickTime just fine until about a month ago.
All the folders in which these movies were stored in 4 folders in 2 folders in one folder. All folders at each level were encrypted with Stuffit Deluxe a version circa 2008 and decrypted with a newer Stuffit Deluxe 10.x. Other movies that are NOT .mov and in with the .mov movies still run.
Your information does not indicate whether or not the files actually played on the current system or were transferred from a different system which was properly configured for playbac, whether or not you recently upgraded your operating system/modified your codec component configuration by adding or deleting any codecs, whether your compound "Stuffing" of the files created corruption, etc.
As to MOV files the selves, this extension just implies the data was placed in the QT generic file container and the actually data could be of any compression format thathat was compatible with the codec component configuration for the system on which the files were created and could include natively supported system codecs, pro editing codecs, and/or third-party proprietary or hybrid codecs. (I.e., this is why we may need more information regarding the individual non-playing files.)
If I click on the Thumbnail Preview "It" runs.
f you are referring to QuickLook (QL) then the technology is different than QuickTime (QT). In the former case, the system is playing representative data but not actually opening the file as QT does. Thus, there is always the possibility that the problem is in the file structure (atom) information. For instance, suppose someone merely changed the MOV file extension in the Finder rather than actually copying data to a real MOV file container. Then it is possible that the QT player app may be searching for a codec that is not supposed or expected to be supported in the MOV file container and, not finding it, issues the erroneous codec error message—especially since you did not inticate the source of the file you are trying to play or, in some cases, which QT player is now not playing the file.
In short, there are several possibilities here and not enough specific information.
Maybe you are looking for
-
How can I install something on the D:\ drive?
Hi! Very very simple question. I would like to create installer within LabVIEW 8.5 and add some file which should be installed on the D:\ drive on the target machine. I see a lot of predefined folders, but how can I add D:\ as destination??? many tha
-
Burn a CD or DVD for only one user!
Hi, How can I burn a CD or DVD that only my user can read? I go to backup my personal informations and want to sure that no other people have access to this CD. I use the Toast Titanium 7.1.2, but if other software can do this, I can buy it! Thanks t
-
How to sms for group of skype id
how to sms to a group of skype id 's from normal mobile ???? pl help me in getting solution. EDIT : title case changed.
-
Hi all! I am trying to set up a room iView which points to a content store. My requirement is that the end-user will be able to create content on this store but won't see it until the room admin approves. So i did the following: 1) Created a reposito
-
What does the sign mean next to the price of an app? and why can i not purchase it?
THE PLUS SIGN