How can I set a button/link that is visible on all slides?

I want to add a button/link that is automatically visible on all slides (whole project). But it seems it does not work. Any help?

Hello,
It depends on your version. I hope you are on CP6 or later. In that case you have two possiblities:
a shape button on the main master slide (and be sure that all daughter master slides have the objects of the main master slide)
a shape button on the first slide, timed for the rest of the project.
More details: Why I like Shape Buttons - Captivate 6! - Captivate blog
There is also a webinar on demand from Adobe 'Lilybiri's favourite...'
Lilybiri

Similar Messages

I do not see where to enter IP addresses in the Open VPN setup. Also, how can I set it up so that I can choose different servers in the same way as I can currently choose them with my VPN app but for PPTP?

I think I have it working on my iPhone 5. But, I do not see how I can control the exit point that I would like for the VPN. Are all the exit points shown in the VPN setting now going to work with Open VPN, or do they remain PPTP? If I am reading correctly, they look like they remain PPTP. If I cannot control the exit point for open VPN, which exit point is the default in the profile you provided me?I note that Open VPN Connect does not work with any of the new 64 bit devices like the iPhone 5S, the iPad Air, and the new iPad MIni. Is there any chance that you guys will come up with an update for your app so that open VPN can be made to work on all iOS devices? That would be nice, particularly if the Open VPN Connect app does not give me a choice of exit points.Thanks,
I do not see where to enter IP addresses in the Open VPN setup. Also, how can I set it up so that I can choose different servers in the same way as I can currently choose them with my VPN app but for PPTP?
Just a quick note to tell you that Open VPN has updated their app so that it is compatible with 64 bit ARM devices like the iPhone 5S, the iPad Air, and the iPad Mini Retina.That does not resolve the problem of how to easily choose among the various possibilities for the exit server. We need to find an easy way to choose.

Thank you for trying the new Firefox. I'm sorry that you’re unhappy with the new design.
I understand your frustration and surprise at the removal of these features but I can't undo these changes. I'm just a support volunteer and I do not work for Mozilla. But you can send any feedback about these changes to http://input.mozilla.org/feedback. Firefox developers collect data submitted through there then present it at the weekly Firefox meeting
I recommend you try to adjust to 29 and see if you can't make it work for you before you downgrade to a less secure and soon outdated version of Firefox.
Here are a few suggestions for restoring the old design. I hope you’ll find one that works for you:
*Use the [https://addons.mozilla.org/en-US/firefox/addon/classicthemerestorer/ Classic Theme Restorer] to bring back the old design. Learn more here: [[How to make the new Firefox look like the old Firefox]]
*Use the [https://addons.mozilla.org/en-US/firefox/addon/the-addon-bar/ Add-on Bar Restored] to bring back the add-on bar. Learn more here: [[What happened to the Add-on Bar?]]

How can I set up email so that if I delete a message on the iPhone it deletes it on my mac

How can I set up my email so that if I delete a message on my Mac it will also be deleted on my iPhone 6 and iPad

Why would you want that?
Doing so would defeat the purpose of syncing the email account.
Simply move the message to a folder or leave it in the inbox.

HT2534 ummm, we don't have the none button to select for our payment type, how can you set it up without that button or a credit card??? apple isn't doing to good of a job so far and i'm not impressed

Hi, I'm setting up an account for my brother, but apparently we need a credit card. Neither of us own one and the system won't let us continue without one. Now I know that there's supposed to be a none selection, but it won't appear on ours. How can we continue if we don't have a credit card or the none selection button??? Help us please!!!!

When I created a new account on my computer's iTunes yesterday, I first logged out of my existing account. I then found a free app in the store, clicked on it's free 'price' to 'buy' it, clicked on 'create Apple id' and filled in details about the new account and which gave me the option of 'none' for the payment details - clicking on the 'verify' email that I received then allowed me to download a free app.
That is the process that you are using when you tried to create both new accounts ? The instructions won't work on existing accounts (even if the account has only been partially created), and you are in the country that you are trying to create the account for ?

When I email myself a picture from my iphone 4s, the email is sent from an email account that I don't have set up as the default account. How can I set it up so that the emails are coming from the default account selected in Mail?

Under my mail tab, it shows that I have a specific email account set up as a default account. That is the account I would like for me emails to be sent from. But when I actually send out an email such as a picture, it is being sent from one of my different email accounts that is not set up as the default. How can I change this so that future messages will be sent from the default account? Any advice would be appreciated. Thanks!!

All photo attachments received or sent with the iPhone's Mail app appear inline or viewed in place within the body of the message when viewed with the iPhone's Mail app which is the same with the Mail.app on a Mac. A photo attachment that appears inline or viewed in place does not mean the photo was not sent as a true attachment to the message. A photo attached to a message with the iPhone's Mail app is sent as a true attachment to the message. How an inline or viewed in place attachment appears on the recipient's end depends on the recipient's email client. If the recipient's email client does not support viewing an attached photo inline or viewed in place within the body of the message, the attached file must be manually selected and opened to viewed.
I am getting the email with the Picture Inline ( not as attachment),The picture is shown distorted , no metter what i do and with what mail client i am using (Gmail\Hotmail\My Enterprise exchange mail), i still get the same behavior.
With which email client?

How can i make a button link in flash??

Hey Guys,
Im pretty new to flash but really need your help and
guidance. I have a nice video ive created, and i want to make the
buttons link to certain pages on a website it will be displayed at.
If you want to see the flash video in place on the website,
visit www.loveandmarriagebridal.co.uk - i want to make the buttons
to link to the following pages.
button 1. www.loveandmarriagebridal.co.uk/index.php
button 2. www.loveandmarriagebridal.co.uk/about_us.php
button 3. www.loveandmarriagebridal.co.uk/
button 4.
http://loveandmarriagebridal.co.uk/account.php
button 5.
http://loveandmarriagebridal.co.uk/contact_us.php
Could anybody please tell me exactly what i need to do in
order to acheive that. I am using Flash CS3. Ive looked around the
net for a solution, but i honestly have no idea what im searching
for.
Your help would be very much appreciated
Thanks
Andy

See which form of ActionScript you used to make the site.
Open the Actions panel and see whether you've chosen AS versions 1
& 2, or AS 3. If you've picked the earlier versions, you can
attach a link easily to each button by clicking on the button, and
adding a little code in the Actions panel. Turn on ScriptAssist to
make it easier. Click on "on" and choose "release" or "press" or
both. Then scroll down the commands on the left and add getURL. You
will then have a few lines that say something like, on(Release)
getURL("putyourpageurlhere"). See bottom for exact syntax. That's
all. The new .html or .php page will load when the button is
clicked.
If your buttons are not actually four-state buttons, but
graphic or movie clip symbols, you will have do it a little
differently. Instead of attaching the code to a button, you attach
it to a keyframe. You give your symbol an instance name in the
property panel, then in the Actions panel create a function that
says essentially: when you click on this instance (onRelease)
getURL.
If you're using AS3, the concept is similar but the code is
different. With a quick search you can find dozens of code examples
that you can cut and paste.
Here's that AS2 button code...

How can I set it up so that clients can respond to the threads in their cases.

What can be done to allow clients that are logged into the member areas to respond to a case thread that is on going.

Hi,
The only option I can see is needing to use the CST feature instead. The system will allow customer interaction and will track the conversation through email instead.
We do not have an option for case responding through the actual site otherwise.
- http://kb.worldsecuresystems.com/196/bc_1966.html
Kind regards,
-Sidney

How can I set a right link Aggregations?

I have a Enterprise T5220 server, running Solaris 10 that I am using as a backup server. On this server, I have a Layer 4, LACP-enabled link aggregation set up using two of the server's Gigabit NICs (e1000g2 and e1000g3) and until recently I was getting up to and sometimes over 1.5 Gb/s as desired. However, something has happened recently to where I can now barely get over 1 Gb/s. As far as I know, no patches were applied to the server and no changes were made to the switch that it's connected to (Nortel Passport 8600 Series) and the total amount of backup data sent to the server has stayed fairly constant. I have tried setting up the aggregation multiple times and in multiple ways to no avail. (LACP enabled/disabled, different policies, etc.) I've also tried using different ports on the server and switch to rule out any faulty port problems. Our networking guys assure me that the aggregation is set up correctly on the switch side but I can get more details if needed.
In order to attempt to better troubleshoot the problem, I run one of several network speed tools (nttcp, nepim, & iperf) as the "server" on the T5220, and I set up a spare X2100 as a "client". Both the server and client are connected to the same switch. The first set of tests with all three tools yields roughly 600 Mb/s. This seems a bit low to me, I seem to remember getting 700+ Mb/s prior to this "issue". When I run a second set of tests from two separate "client" X2100 servers, coming in on two different Gig ports on the T5220, each port also does ~600 Mb/s. I have also tried using crossover cables and I only get maybe a 50-75 Mb/s increase. After Googling Solaris network optimizations, I found that if I double tcp_max_buf to 2097152, and set tcp_xmit_hiwat & tcp_recv_hiwat to 524288, it bumps up the speed of a single Gig port to ~920 Mb/s. That's more like it!
Unfortunately however, even with the TCP tweaks enabled, I still only get a little over 1 Gb/s through the two aggregated Gig ports. It seems as though the aggregation is only using one port, though MRTG graphs of the two switch ports do in fact show that they are both being utilized equally, essentially splitting the 1 Gb/s speed between
the two ports.
Problem with the server? switch? Aggregation software? All the above? At any rate, I seem to be missing something.. Any help regarding this issue would be greatly appreciated!
Regards,
sundy
Output of several commands on the T5220:
uname -a:
SunOS oitbus1 5.10 Generic_137111-07 sun4v sparc SUNW,SPARC-Enterprise-T5220
ifconfig -a (IP and broadcast hidden for security):
lo0: flags=2001000849 mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
aggr1: flags=1000843 mtu 1500 index 2
inet x.x.x.x netmask ffffff00 broadcast x.x.x.x
ether 0:14:4f:ec:bc:1e
dladm show-dev:
e1000g0 link: unknown speed: 0 Mbps duplex: half
e1000g1 link: unknown speed: 0 Mbps duplex: half
e1000g2 link: up speed: 1000 Mbps duplex: full
e1000g3 link: up speed: 1000 Mbps duplex: full
dladm show-link:
e1000g0 type: non-vlan mtu: 1500 device: e1000g0
e1000g1 type: non-vlan mtu: 1500 device: e1000g1
e1000g2 type: non-vlan mtu: 1500 device: e1000g2
e1000g3 type: non-vlan mtu: 1500 device: e1000g3
aggr1 type: non-vlan mtu: 1500 aggregation: key 1
dladm show-aggr:
key: 1 (0x0001) policy: L4 address: 0:14:4f:ec:bc:1e (auto) device address speed
duplex link state
e1000g2 0:14:4f:ec:bc:1e 1000 Mbps full up attached
e1000g3 1000 Mbps full up attached
dladm show-aggr -L:
key: 1 (0x0001) policy: L4 address: 0:14:4f:ec:bc:1e (auto) LACP mode: active LACP timer: short
device activity timeout aggregatable sync coll dist defaulted expired
e1000g2 active short yes yes yes yes no no
e1000g3 active short yes yes yes yes no no
dladm show-aggr -s:
key: 1 ipackets rbytes opackets obytes %ipkts %opkts
Total 464982722061215050501612388529872161440848661
e1000g2 30677028844072327428231142100939796617960694 66.0 59.5
e1000g3 15821243372049177622000967520476 64822888149 34.0 40.5

sundy.liu wrote:
Unfortunately however, even with the TCP tweaks enabled, I still only get a little over 1 Gb/s through the two aggregated Gig ports. It seems as though the aggregation is only using one port, though MRTG graphs of the two switch ports do in fact show that they are both being utilized equally, essentially splitting the 1 Gb/s speed between
the two ports.
Problem with the server? switch? Aggregation software? All the above? At any rate, I seem to be missing something.. Any help regarding this issue would be greatly appreciated!If you're only running a single stream, that's all you'll see. Teaming/aggregating doesn't make one stream go faster.
If you ran two streams simultaneously, then you should see a difference between a single 1G interface and an aggregate of two 1G interfaces.
Darren

How can you create a button master that can be unlocked but where edits to the master will affect all buttons?

I'm creating a course calendar (January - December) for an organization and courses are repeated several times throughout the year. I've been asked to create this as an interactive pdf rather than as an interactive Indesign document that can be viewed via a browser, so I'm unable to use multi-state objects
Anyway, I've created button masters for such buttons such as previous page/next page, course index and search on my master pages, so that's all fine and dandy as I don't need to move these elements. The way I have set up the calendar is that you click on the course name (a button) and a popup (also a button) shows up with a course description - I want to be able to move these popups so that they are the general vicinity of the course name button and not just floating about in the centre of the calendar.
However, because course descriptions or what is offered in the course change frequently and I am expected to keep the calendar up to date, it doesn't seem efficient to have to manually change every description for a course popup that shows up several times throughout the year or even several times on a month. The issue is that even if I create the popups on the master page, as soon as I unlock them on my month pages and move them to where I want them to be...they'll no longer be affected by changes to the master.
Is there some sort of function like in html/CSS where you can assign a class to a button or something? Or it is something that Indesign isn't capable of and I will just have to do it manually and try to be careful not to miss any courses when they are updated?
Any help is appreciated!

While you could create a different screen for each, a better way to do this is via some form of database. The buttons cause functions to be executed and the functions utilize data resources based on the selections that are established.
So if you pick a particular character, a variable is a assigned a value that indicates that. That variable is then utilized to extract the data associated with the character and to build the screen elements related to the options for that character.

How can I properly embed deep links that contain http: twice

Hi,
We have an online bookstore where we need to embed deep links to a booktopia page. I have tested the links given to us by the affiliate program (DGM performace) and they work perfectly but when I embed them into muse and hit publish they give me a server not found page.
http://academyhypnoticscience.businesscatalyst.com/academy-bookstore.html
I have established that this seems to be an error in the way muse is interpretting the link (or maybe business catalyst) as the link I paste into muse is:
http://t.dgm-au.com/c/63052/71095/1880?u=http%3A%2F%2Fwww.booktopia.com.au%2Ftrancework-an -introduction-to-the-practice-of-clinical-hypnosis-michael-d-yapko%2Fprod9780415952590.htm l
but when I click on the link on the website (on the image of the first book) I get this:
http://http%3a%2f%2fwww.booktopia.com.au%2ftrancework-an-introduction-to-the-practice-of-c linical-hypnosis-michael-d-yapko%2fprod9780415952590.html/?clickid=yV0WHZyIfUJsUl0wAFyspSG PUkW3tATpbw2qTw0
and when I right click on the image and copy the link location I get this:
http://t.dgm-au.com/c/63052/71095/1880?u=http%253A%252F%252Fwww.booktopia.com.au%252Ftranc ework-an-introduction-to-the-practice-of-clinical-hypnosis-michael-d-yapko%252Fprod9780415 952590.html
Any ideas?
Cheers,
Tina

You can't have two http in a URL. Why do you have two? Try taking one out.

HT5114 How can I set up apple ID that uses parents account but separate account for child to download apps and they will not be on my apple products?

Need help setting up IPod Touch for my 8 year old where he has his on apple ID under me the parent but I don't get all his Apps on my apple products?

See Here > Apple ID: Contacting Apple for help with Apple ID account security
Ask to speak with the Account Security Team...

How can I set the text feild in a form to print out the entire feild?

Right now it's only printing out what shows in the box, I want the box to expand when printed and show all the text entered in the field, how can I set it to do that?

I think that the font size has to be set in the form itself, not the FDF.

How can I set double-click of JPGs to open in Photoshop instead of Camera Raw?

Like the title of this topic says, how can I set up Bridge so that double-clicking a JPG opens it directly in Photoshop, instead of going through the intermediary Camera Raw dialog box first?
And yes, I do have my File Type Associations for all JPGs set to open in Photoshop.
I also have Camera Raw preferences set to NOT "always open JPEG files with settings using Camera Raw".
I'm using Bridge 2.1.1.9 and Photoshop CS3 10.0.1 on Mac OS X 10.5.2 on Intel.

First double check if you have the options in the prefs indeed unchecked.
If so restart Bridge holding down option and choose the refresh preferences option, reset the prefs again to your wishes and restart Bridge.

How can i set photoshop image resolution

how can i set image resolution so that opening an image into photoshop CS5 the image will always be at a certain resolution, such as 240ppi?

never mind. i must have overlooked it 20 times while going thru preferences.
need more caffeine.

How can i set action on UITaBar and get event from that

Hi All,
I m doing one apps in which i have to add three UITabBarItem and this is UITabBarSystemItem.
Now i cannot understand that how can i set action and get event from the?
And how can i set various views on three tab bar item.
I have to use UITabBar means i have to use UINavigationController+UITabBar
My code id
tabBar =[[UITabBar alloc] initWithFrame:CGRectMake(0,370,320,50)];
tabBar.backgroundColor =[UIColor blackColor];
UITabBarItem *search =[[UITabBarItem alloc] initWithTabBarSystemItem:UITabBarSystemItemSearch tag:0];
UITabBarItem *recents =[[UITabBarItem alloc] initWithTabBarSystemItem:UITabBarSystemItemRecents tag:1];
UITabBarItem *favorites =[[UITabBarItem alloc] initWithTabBarSystemItem:UITabBarSystemItemFavorit es tag:2];
tabBar.items =[[NSArray arrayWithObjects:search,recents,favorites, nil] retain];
tabBar.selectedItem = search;
[myView addSubview:tabBar];
[tabBar release];
I add a action:
UITabBarItem *search =[[UITabBarItem alloc] InitWithTabBarSystemItem:UITabBarSystemItemSearch tag:0 action:@selector(select:)];
So it error: Warning -no'InitWithTabBarSystemItem:tag:action:' method fount
So any can help me regarding it?

Thanks RickMaddy very much.
I read and do with sample at the View Controller Programming Guide . But when run it only view TabBar with title but haven't got any TabBarItem on it. I searched a few example about TabBar and i did, but i want do a form with a button then press on button it view a form with 2 TabBarItem on TabBar and press each TabBarItem will show correlative form page 1, page 2.
UITabBarController *tabBarControl = [[[UITabBarController alloc] initWithNibName:nil bundle:nil] autorelease];
tabBarControl.title = @"Tab bar";
ViewControl1 *view1 = [[[ViewControl1 alloc] initWithNibName:@"ViewControl1" bundle:nil] autorelease];
ViewControl1 *view2 = [[[ViewControl1 alloc] initWithNibName:@"ViewControl2" bundle:nil] autorelease];
tabBarControl.viewControllers = [NSArray arrayWithObjects:view1,view2,nil];
[self.navigationController pushViewController:tabBarControl animated:YES];

How can I set a button/link that is visible on all slides?

Similar Messages

Maybe you are looking for