How can I tell if WES610N is using 5 GHz band?

Hello,
I'm using a WES610N Media Connector with my Blu-Ray player to stream video.  The router is an EA3500 -- I used the smart, one-touch WiFi setup to do the setup for the WES610N.
How can I tell if the Media Connector is using the 5 GHz band vs. the 2.4 GHz band?
Is there a way t interrogate it while it is connected to my Blu-Ray player in another room?
Thanks in advance,
Bill

Yes. Agreed with sabretooth. There's no way for us to identify on what band your WES610N is connected to unless you'll create a different SSID's on both 2.4 and 5.0 Ghz bands.
If everyone needs to believe in something, I believe I'll have another beer..

Similar Messages

  • Updating PS CC 2014--how can I tell if I am using the latest version?

    I just updated Bridge, PS and LR from the Creative Cloud, but when I went to use them, I was still using the old versions despite the fact that CC said I had updated to the latest versions.  A thread in the LR forum led me to sign out and back into Creative Cloud, and that did the trick for LR.  However, I cannot discern any changes in PS.  How can I tell if I am using the latest version of PS?  When I click on About Photoshop, the popup says:
    TIA.

    that's the latest ps as of today.

  • HT1338 Yesterday, I purchased Mountain Lion OSX and tried to download it but I don't think it worked.  How can I tell if I am using Mountain Lion and how do I get help if the download was unsuccessful?

    Yesterday, I purchased Mountain Lion OSX and tried to download it but I don't think the download worked.  How can I tell if I am using Mountain Lion and how do I get help if the download was unsuccessful?

    Click your Apple menu icon top left corner of your screen.
    From the drop down menu click About This Mac.
    If Mountain Lion is installed, it will say:  v10.8
    If not, launch the App Store. From the App Store menu bar click Store > Check for Unfinished Downloads
    FYI ..  for downloading Mountain Lion from the App Store, a high speed (broadband) internet connection is strongly recommended by Apple as noted here > iTUNES STORE - MAC APP STORE - TERMS AND CONDITIONS
    If you need to reinstall OS X or repair the the startup disk Mountain Lion Recovery, that requires broadband access to the internet via Wi-Fi or an Ethernet connection. OS X is downloaded over the internet form Apple when OS X Recovery is used for reinstallation.

  • How can we tell the printer to use a different paper cartridge

    Hello all,
    We are using t.code MN05 to assign a printer to each Purchase group. How can we tell the printer to use a different paper cartridge so that purchase orders ( output type ZNEU, ZEU, ZEN) can be printed on a paper with company logotype. Local team are removing most of the printers an we have only one multifunction printer availabel for a large number of employees.
    Thank you for your suggestions

    Hi,
    I can help you about how to use different Paper Tray's but different cartridge case I am not sure...

  • I think my computer was hacked, how can I tell who has been using my account?

    I think my computer was hacked, how can I tell who has been using my account?

    Hi sandys98368807,
    Do you see any unusual activity on your system?
    If you are worried about your Adobe account, i would recommend you to change your Adobe password as soon as possible.
    Please let me know if you have any other query or need any further assistance.
    Regards,
    Rahul

  • HT204380 how can i tell if someone has used facetime, from my phone to call someone and has delated from phone recents

    hi how can u tell if someones used facetime to ring someone from ur phone then deletes from recents

    You can look at your bill with your carrier for the phone call itsef, but not facetime.

  • How can I tell what library is used for readdir?

    I have a problem that a program responds differently on two different unix machines, both of which are running Solaris 2.6, and using the same C compiler (4.2)
    "readdir" returns a "struct dirent" where the d_name is offset by two bytes on one of the machines.
    I have used ldd to detemine the libraries to which it is linked, and although they are linked in a different order, the libraries on each machine are byte identical. I have also proved that the program includes the same dirent.h file on both machines.
    Dumping information from the libraries shows that there is a readdir function in /usr/lib/libc.so.1 and /usr/ucblib/libucb.so.1.
    My assumption is that the header files give the same offset into the structure, but that one of the libraries is returning a differently constructed structure.
    How can I find out if the program is calling the same one at run time?
    Thanks for any help you can give.

    I am reasonably sure that the lib that appears first in the ldd output is the
    lib that is supplying the routine. One way to make sure is to use dbx to
    set a breakpoint in readdir. If there are multiple copies of the readdir
    symbol, which there should be in this case, it will prompt you with a list
    of shared libraries that have the symbol and ask which one you want to
    stop in. Pick one, then run your program. It will either hit the breakpoint,
    in which case it is satisfying the symbol from the lib that you picked, or
    it will not hit the breakpoint, in which case it is not getting it from that lib.
    Delete the first breakpoint, then set another breakpoint in the same routine
    and tell it to stop in the other lib. The fact that it stopped in the first lib
    means that it's not likely to stop in the second lib, but there are ways for
    it to hit both or neither. Check them both.

  • How can I tell if I'm using my discrete Quadro 1000M GPU?

    I just recieved my w520 in the mail today, and I have no idea how I can tell when the optimus kicks in or if it's even using the discrete card. I already downloaded the driver for the 1000m. Anyone know how I can check what card it's using?

    See File Edit Desktop Help in the menubar. Select 'Desktop' and look there in the dropdown menu :-)
    You can use 'autoselect' for general use, discrete for performance. Most people suggest autoselect and changing it when you need to, or better just go to the menu I mentioned and select 'Add run on graphics processor' to context menu then you can select the gpu to use from explorer.
    What you mentioned, 3D Setting, Manage 3D settings under Select a task is another place you can select which processor to use by clicking program settings on the right and creating a profile for the app you intend to run.
    Btw what do you mean on your question then? Either the activity monitor shows it running on the Nvidia gpu or it's not. If you wish lower level information on how this works you might wish to peruse some doc on Nvidia's Optimus switching, it may help you but I think the gpu monitor is what you want :-). Basically with our w520s if it is on the external display it will be run on the discrete gpu (I think I read the external video connectors go to the discrete card), if you have your laptop lid open, you could select Nvidia or integrated. The driver can also override your selection. This is my rough understanding of how our systems are wired and how things work. Someone add to/or correct this if they wish. You may wish to look for some articles/discussion on the hardware switching/muxing and how that works between the gpus. I need to reread it all myself.

  • How can I tell what took someone used to make a flash...

    When I'm out surfing around I come across Flash that I'd love
    to make a one of. For example I like to do photography and I see a
    Flash window that has thumbs across the bottom and a larger picture
    on top, and then if you click on one of them you get a much larger
    pictures, I looked at the source for the page, but I can't see any
    clue as to what tool make that Flash...
    If I like what someone has created in Flash, how can I figure
    out how they made it?
    Thanks
    Kelvin

    I don't have problems with many things, but being called a
    THIEF is one of them.
    I did not say that I am helping the community move forward by
    decompiling others work.
    I did say that the community CAN move forward FASTER when
    people stop getting hung up on the idea that their code is
    something SACRED.
    If you develop something new that has never been done before,
    then you have something that you can protect.
    If you want to see how other people did it, so that you can
    better understand the different methods that can be used to do that
    one thing, you are not stealing.
    I know many people that take the same stance that I do.
    People that look at code to understand it. Most of the things I can
    do today because I looked at other peoples code. I didn't copy it,
    I took hints from methods and used them to create my own methods.
    Sometimes I decompile something, knowing how I would do it,
    to see how that person did it. If they have any hints at better
    methods that I could use to make my code faster, better. To say
    that the majority of people steal is to take the standard American
    view on the world. Americans tend to believe that everyone else is
    a thief, a crook, whose only intent is to do wrong. (I am BTW, an
    American, and I am very proud to be an American) If you step back,
    and open your views, and your code, you will find a much different
    picture painted. The majority of people aren't looking for
    something to steal, but they are forced to take methods that people
    would consider "stealing" to learn to do the things that they want
    to do.
    There are many good reasons to look at code, with or without
    the permission of the person who wrote it.
    In the end, these are my views, and I am not alone in them.
    Those are your views, and you are not alone in them. If you lose
    respect for me, then you do. I am here to help who I can help with
    the knowledge and experience that I have gained over my time as a
    web developer. I only entered these forums recently, and therefore
    don't have anywhere near as many posts as you do, but that doesn't
    make my position any less accurate. The advice I have given people
    is correct and true, and I offer up the things that others don't.
    Even if you do not believe in using decompilers, decompilers exist,
    and have their uses, therefore should be mentioned. In the end, I
    lose respect for you, who I have held in VERY high regards since I
    entered this forum, because you are closed minded, and unwilling to
    offer the full information to people who are asking.
    When I create code, I consider it open-source code. I am not
    about to try to fool myself into thinking that people can't see the
    code if I don't want them to. But why would I not want them to.
    Because I spent hours writing it myself. At least, if others see
    it, they won't have to spend as much time to get the same effect. I
    know that some of these people will take it verbatim to use in
    their projects, and not give me credit. But I don't expect credit.
    It is a few lines of code, why should I get credit for writing it,
    when I am not the first, nor the last, to write the same code.
    Please do not respond to this. We both have better things to
    do than sit and debate about the merits of open source code, and
    learning by looking.

  • How can you tell what app is using a file?

    I have a screenshot that I moved to the trash. I try to empty the trash, but it says the file is in use. Is there any way to tell what app is using it?
    Thanks very much.

    There is a shell command (i.e. Unix executable) called fuser.
    This program displays a list containing all the process-ids (PIDs) that are accessing a particular file at a given time.
    To invoke it you just need to open a terminal window, wait for the command prompt (typically a "$"), then type fuser followed by a space and then drag the file from the finder to said terminal window.
    Once the PID list is displayed, you need to look-up the process id (the first column) with the help of activitty monitor to see the name of the app that's accessing the file.
    One final warning: make sure activity monitor is displaying "all processes" because the file is not necessarily being accessed by one of your processes.

  • How can I tell if I need a Dual-Band Wi-Fi Dongle ...

    Hi
    I've just placed an order for BT Infinity 1 and have been advised I will be receiving the new BT Home Hub 5.
    Can someone explain if it would be advantageous for me to order a Dual-Band Wi-Fi Dongle 600 or not?
    How can I check if my laptops - Dell Studio 1749 and HP ENVY dv6 - can already handle dual band connections, if that is what we are talking about here?
    Any advice / help appreciated.
    Thanks
    Solved!
    Go to Solution.

    To be honest, you are unlikely to see any speed improvement by adding a wifi dongle, also the 5GHz band has very limited range.
    I would wait until everything is working, before ordering any more stuff.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • How can I tell what setting was used to create a received PDF?

    I get PDFs all the time and I can't find a way of knowing if the PDF was created using Press Quality, Standard, Smallest File size other than just looking at it and zooming in.
    Is there a menu item or trick that will tell me how this PDF was created?

    The image was almost 9 inches by 7 inches at 300 ppi and I reduced it to about 3 inches wide in my document. I almost never blow-up images unless they can take it without losing resolution.
    Maybe I'm not looking in the right place. I went to preflight > sheetfed offset, clicked on Analyze and got lots of readings. The one that said "Resolution of color and grayscale images is less than 150 ppi. This might be insufficient for proper print results." is the one that threw me.
    It's too bad that I just can't read how the file was created. Most of clients I deal with make PDFs and never look at the settings they use. I'm in the printing business.
    I've just been looking at the PDFs sent to me and zooming in to see if they'll hold up but I'd really like something more accurate.

  • How can I tell which apps are using data

    Perhaps this is a suggestion, just in case someone who is in a position to note this at Apple (not likely?) might read it.
    How about an app included in the OS that allows users to track which apps are transmitting and receiving data through cellular data and/or wireless.
    I keep getting charged by AT&T (it took restraint to not type a bunch of explatives before AT&T) for escessive data usage, even though I'm in wifi 90%+ of each day, and purposely restrict using it when not in wifi. Seriously, I don't now how I could use it less barring not using it at all, and I still get charged for data. I have no idea how to control this since I cannot tell which, if any, apps are transmitting data in the background, or if that's even possible.
    Seriously annoyed at getting charged extra when the 'service' they provide barely works for me the miniscule amount of times I try to use it.

    This is a user to user forum.
    You can leave feedback here
    www.apple.com/feedback/
    You could also try searching for an app that tracks data usage

  • How can we tell the client that use process order or production order (proc

    Dear guru,
    My question on what reason we can tell the client that u have to use process order or production order .
    On what scenario we suggest client that use process order or production order

    Hi,
    Process manufacturing is primarily designed for the chemical, pharmaceutical, food and beverage industries as well as the batch-oriented electronics industry
    Discrete manufacturing is u201Cthe production of distinct items such as automobiles, appliances, or computers,u201D whereas process manufacturing covers u201Cproduction that adds value by mixing, separating, forming, and/or performing chemical reactions. It may be done in either batch or continuous mode.u201D
    Letu2019s think about what your company manufactures. Does it require mixing chemicals? If so, you may need an ERP system that does things like calculate ingredient quantities.
    If your company assembles products from many component parts, youu2019ll require discrete manufacturing functionality
    Other approach:
    If the finish good cannot return back to its basic components, your manufacturing is Process. For instance, the finish good is a can of soda. It cannot return back to its basic components such as carbonated water, potassium benzoate, aspartame, citric acid, and other ingredients. But if the finish good is car or computer, your manufacturing process is Discrete because it can be disassembled and the parts, to a large extent, can be returned to stock. Therefore Bill of Material (BOM) of discrete manufacturing consists of component parts for assembly while Process manufacturing consist of formulas, recipes and other ingredients
    Process manufacturing is scalable. If a formula calls for 1,000 pounds of cake flour, but you only have 500 pounds, you can still bake cakesu2014just not as many. Conversely, in discrete manufacturing, one missing part means waiting for it before the finished assembly unit can start rolling off the production line
    The obligatory requisite for process manufacturing is Lot Potency and Shelf Life where as discrete manufacturing values Serial Numbers, ECNu2019s and assembles.
    If it is discrete manufacturing ---go for Production order
    If it is process manufacturing ---go for process order
    thanks and regards
    Venkat V

  • How can i tell if i am using vpn on this computer?

    I live in South Korea and I purchased a VPN but later realized I do not need it.  Now, the site I am trying to access (NFL.com gamepass) does not allow users from within the USA to use their product but it seems the VPN is still working.  I contact NFL customer service and it keeps telling me that my IP address is in the USA.  The VPN must still be active but I cannot locate where to disconnect it. 

    Please open the Network preference pane in System Preferences. It may be obvious whether you have a VPN connection in the list on the left. If not, post a screenshot of the window. Depending on what type of VPN you installed, you might not see it in the connection list.

Maybe you are looking for