How can i use labview for notebook

i want to know spec of notebook for install labview programm.
thank you vermuch.
sattaya

Sattaya,
here you can find the system requirements for installing the LabVIEW development environment.
Please post merely LabVIEW related questions to the LabVIEW board. The LabVIEW community is much bigger than the motion control community, so you will get answers quicker there.
Regards,
Jochen Klier
National Instruments

Similar Messages

How can i use labview for communicating with pic18 microcontroller through usb port?

Hi all,
I want to make a DAQ card using pic 18 microcontroller which has a built-in usb protocol. I have the firmware of this
controller which will make it as a usb device. How can i receive the analog voltages from this DAQ card in Labview? or i mean to say that how i can communicate labview with the Pic 18 microcontroller through usb port? I have also the
mpusbapi.dll file which is for Visual C++. Can i make changes in this dll file to make it compatible with labview?

Which labview version do you have. Up to labview 7.1 it was no USB raw communication options. I have heard it did not work well in 7.1, but from 8.x most of the errors were fixed.
Here is a link it should be useful http://forums.ni.com/ni/board/message?board.id=170&message.id=340676&query.id=365864#M340676
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

How can I use TopLink for querys that have two and more tables?

I use TopLink today, and I can use one table to query, but how can I use TopLink for querys that have two and more tables?
Thank you for see and answer this question.

You can write a custom SQL query and map it to an object as needed. You can also use the Toplink query language "anyOf" or "get" commands to map two tables as long as you map them as one to one (get command) or one to many (anyOf command) in the toplink mapping workbench.
Zev.
check out oracle.toplink.expressions.Expression in the 10.1.3 API

How can I use OCCI for oracle8.1.6?

my database is oralce8.1.6 for solaris8.
I want to develop database application by OCCI .
But only oracle9i has OCCI.
How can I do?
Where can I get OCCI ,and how can I use it for oralce8.1.6?
thank you very much!!

OCI is available for all versions of Oracle including Oracle
7/8/8i etc. However it is not installed by default with these
versions. I am assuming that the default 9i installation
includes OCI. You should be able to install OCI for other
versions through one of the development platforms e.g. ProC/C++
etc.

How can i use AME for the new OAF page.

Dear all,
I have developed a new OAF page and registered under Employee Self Service.
How can i use AME for the approval process.
Appreciate your ideas?
zamora

I will try to answer based on my experience of working with iProcurement and AME. It depends on how you want to make a call to AME , directly from OAF Page or from Workflow and your requirement. You didn't specify what you want to show the users on OAF Page and your business requirement.
Before calling AME Engine from the OAF page or workflow, I guess you did already setup AME Transaction Type and it's Approval Groups, Conditions, Action Types and Rules. Do some testing from AME Business Analyst Test Workbench. Please note that, AME provides lot of PL/SQL API's that you have to call from your programs (java or workflow pl/sql)
Let's look at the workflow and putting an OAF Page as notification.
As Sameer said, you have kick-off workflow process from PR of CO and with in the workflow function, you make a call to AME Engine API's with the AME Transaction ID. This transactionId belongs to the AME Transsaction Type that you setup. Based on the rules setup, AME Engine generates list of approvers/approver and stores them AME Tables for that transactionId. Then, it sends a notification to the approver.
In the workflow, where that notification is defined, in the message body you have to put an attribute(&XX_WF_FWK_RN) of type document/send. And this attribute will have the constant JSP:/OA_HTML/OA.jsp?OAFunc=XX_FUNC&paramId=-&DOCUMENT_ID-. This function is SSWA Jsp function that makes a web html call to your OAF Region.
If your requirement is to just show the list of approvers on the OAF Page, you may have to call AME API diectly passing your AME TrasnactionId with other parameters. Then AME generates list of approvers and stores them in AME tables with each approver status. You can pickup those approvers using VO and show them on OAF Page.
Hope this gives some idea.

How can i use RTFEditorKit for JTextField.

hi all,
how can i use RTFEditorKit for JTextField.
thanks in advance
daya

Don't cross post. This is a Swing related question and you have already posted in the Swing forum:
http://forum.java.sun.com/thread.jspa?threadID=619619&tstart=0

How can I use Siri for IPhone?

How can I use Siri for IPhone?

Siri only works on the iPhone 4S or iPhone 5. If you have one of those devices, turn it on in Settings > General > Siri.
If you need more info than that, ask in the Apple forums.

How can I use music for ringtones on my iphone 4?

How can I use music for ringtones on my iphone 4?

You can take any MP3 file that it 40 seconds or less and change the file extension to M4R. Then drag it into iTunes. It will appear under Ringtones and transfer over next time you sync,

How can I use LabVIEW to send the equivalent of a CTRL D (in VT 100 format) out the serial port of my computer?

I am trying to write a vi that interfaces with a piece of OEM equipment that is set up to talk with a VT 100 terminal. I can't seem to locate the ASCII equivalent string (if there is such a thing) of a CTRL D. Is there a vi that emulates VT 100 commands?

If I recall, CTRL-D is EOF on most ASCII tables.
You'd probably have to use an escape sequence
or if you can use an unsigned 8-bit that might be
easier.
In article <[email protected]>, TLS
wrote:
> How can I use LabVIEW to send the equivalent of a CTRL D (in VT 100
> format) out the serial port of my computer?
>
> I am trying to write a vi that interfaces with a piece of OEM
> equipment that is set up to talk with a VT 100 terminal. I can't seem
> to locate the ASCII equivalent string (if there is such a thing) of a
> CTRL D. Is there a vi that emulates VT 100 commands?

How can i use dlls for running rtc3?

how can i use the dll libraries to use for the rtc3 software?

amolchoudhary wrote:
can anyone please help me???
How? You provide almost no useful information.
What is rtc3?
Why do you think you have to use DLLs?
What did you try so far that hasn't worked?
What is it you want to accomplish?
You see what you ask here is just about the same as if someone would ask you to tell them what screw he needs to fix his car.
Rolf Kalbermatter
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

How can I use XSQLRequest for processing in-memory XMLDocument

How can I use class XSQLRequest for processing in-memory XSQL?
What should i pass in URL parameter value for constructor XSQLRequest(XMLDocument p0, URL p1)?
Could you write the some examples?

Here's one example of doing this:
String xsqlPage = "<page connection='demo' xmlns:xsql='urn:oracle-xsql'>"+
                  " <xsql:set-page-param name='username' value='{@u}'/>"+
                  " <xsql:set-page-param name='password' value='{@p}'/>"+
                  " <xsql:query bind-params='username password'>"+
                  "    select 'Authenticated' from dual"+
                  "    where 'SCOTT' = UPPER(?) /* username */"+
                  "      and 'TIGER' = UPPER(?) /* password */"+
                  " </xsql:query>"+
                  "</page>";
DOMParser d = new DOMParser();
d.parse( new StringReader(xsqlPage));
XSQLRequest req = new XSQLRequest(d.getDocument(),null);
StringWriter sw = new StringWriter();
PrintWriter errors = new PrintWriter(sw);
Hashtable h = new Hashtable(2);
h.put("u","scott");
h.put("p","tiger");
req.process(h,output,errors);
output.println(sw.toString());

How can i use autoSuggestBehavior for inputText witha separator

I use JDEVADF_11.1.1.2.0
how can i use a input Text Field with auto suggest by sepearted
in a field with what, is separated
Example Value :"Name1;Name2;Name3......"
Sorry for my English

I'm not exactly sure what do you mean here.
The basics of working with autosuggest are here:
http://www.connotea.org/user/jdeveloper/tag/auto%20suggest

I have a passport external hard. previously, I used it on windows, then I changed my laptop to mac. Now, It's only read. How can I use it for copying files on it on mac? I don wanna use it on windows again.

I have a passport external hard. previously, I used it on windows, then I changed my laptop to mac. Now, It's only read. How can I use it on my mac for copying files on my passport? I don wanna use it on windows again.

If you're not going to use the drive on a Windows machine, you should use Disk Utility (Applications>Utilities folder) to erase the drive and format it as "Mac OS Extended (Journaled)" with a single GUID partition (default):
Good luck,
Clinton

How can I use LabView to control Altera Scripting

Hi
I have kind of run into a stone wall. I am building a production test executive based on LabView. Part of this process includes loading an FPGA image on to a CFI flash that is in the JTAG chain. I am trying to make so that the production operators don't have to open a second application, select the right FPGA and Flash navigate to the file then load it, then go back to LabView and run the rest of the tests.
Altera has a command line interface that will let me load .cdf file. The problem is that nowhere in Altera’s documentation does it show me how to first load the “Parallel Flash Loader IP” into the FPGA. The flash loader acts as a temporary bridge between the JTAG input and the CFI Flash. I have looked on Altera’s Forums and have had an open ticket with Altera’s support engineers for more than a week.
I can’t be the first person to want to do this; I am hoping someone here has done it before. I would really rather not try to use the activeX controls to manipulate the windows based program.
Any suggestions would be greatly appreciated (Note I am not trying to put LV code on the FPGA/Flash just use LV to control the process)
Thanks in advance
Below is the error message and the script I am using. It almost works just missing the flash loader IP
C:\altera\12.1sp1\qprogrammer\bin>quartus_pgm -c USB-BLASTER -m JTAG S_FPGA.
cdf
Info: *******************************************************************
Info: Running Quartus II 32-bit Programmer
    Info: Version 12.1 Build 243 01/31/2013 Service Pack 1 SJ Full Version
    Info: Copyright (C) 1991-2012 Altera Corporation. All rights reserved.
    Info: Your use of Altera Corporation's design tools, logic functions
    Info: and other software and tools, and its AMPP partner logic
    Info: functions, and any output files from any of the foregoing
    Info: (including device programming or simulation files), and any
    Info: associated documentation or information are expressly subject
    Info: to the terms and conditions of the Altera Program License
    Info: Subscription Agreement, Altera MegaCore Function License
    Info: Agreement, or other applicable license agreement, including,
    Info: without limitation, that your use is for the sole purpose of
    Info: programming logic devices manufactured by Altera and sold by
    Info: Altera or its authorized distributors. Please refer to the
    Info: applicable agreement for further details.
    Info: Processing started: Thu Oct 03 18:16:53 2013
Info: Command: quartus_pgm -c USB-BLASTER -m JTAG S_FPGA.cdf
Info (213045): Using programming cable "USB-Blaster [USB-0]"
Info (209060): Started Programmer operation at Thu Oct 03 18:17:19 2013
Error (209062): Flash Loader IP not loaded on device 1
Error (209053): Unexpected error in JTAG server -- error code 5
Error (209012): Operation failed
Info (209061): Ended Programmer operation at Thu Oct 03 18:17:21 2013
Error: Quartus II 32-bit Programmer was unsuccessful. 3 errors, 0 warnings
    Error: Peak virtual memory: 376 megabytes
    Error: Processing ended: Thu Oct 03 18:17:21 2013
    Error: Elapsed time: 00:00:28
    Error: Total CPU time (on all processors): 00:00:03
Solved!
Go to Solution.

Hi Eric,
I got it figured out today, basically you have to load the Parallel Flash Loader first into FPGA ram. It is a special .sof file (pfl_epXXXX.sof) based on your FPGA. Code is actually pretty straight forward, using the Sys Exec VI. Use the windows based programmer to generate the .cdf file that identifies your FPGA, attached Flash and .pof file .
Syntax was odd going into Sys Exec. Note the extra "C" in in front of the "quartus_prm.exe" I have no idea why that was needed, but I was getting an error until I just happened to put it in there (Blind Luck :-))
I used a 2 element array going into a four loop
cmd /cquartus_pgm.exe -c USB-BLASTER -m JTAG -o P;pfl_epXXXX.sof
cmd /cquartus_pgm.exe -c USB-BLASTER -m JTAG S_FPGA.cdf
Defining the working director C:\altera\12.1sp1\qprogrammer\bin
And added match string with "Successfully performed operation" on the output in the loop to make sure everything loaded correctly then adding the array to give me a overall P/F
To anyone doing this same thing Altera's documentation is poor to say the least. It took most of a week to figure this out Not allowed to upload code, so anyone wanting details just post here and I will try to help. This was painful, with lots of lessons learned.
Thanks for the interest though
Best regards John

How can i use labview.tlb to control Labview from an external application?

Hi,
I've been told by a labview engineer that i could use the file
labview.tlb located in the labview install folder to control labview
from an external application (in my case, a C# app). I'm using Labview
6.1 under Windows 2000. This article confirms that:
"ActiveX and LabVIEW"
http://zone.ni.com/devzone/conceptd.nsf/webmain/5401BE584FBAEECE862567C2006D36C7?opendocument
But i've not been able to find out how to use this file to achieve
what i want. I just want to be able to open/close labview, open/close
a vi, start/stop a vi, hide/show a vi from a C# application. The above
web page talks about activex but i really don't see the realtion
between activex and that labview.tlb file.
Is there so
mebody around who knows how to use that file? Why does NI
tell us that it's possible to do what i want to do but doesn't explain
how (or hides this info very well)?
Thanks

Hi,
> Hi I am fighting a similar problem and so far I found this: Calling
> LabVIEW from C++ Using ActiveX
>
> http://sine.ni.com/apps/we/niepd_web_display.DISPLAY_EPD4?>p_guid=B45EACE3E21356A4E034080020E74861&p_node=DZ52051&p_submitted=N&p_rank=&p>_answer=&p_source=External
Thanks for the link, i actually already found this link before. I've
found yesterday how to use Labview.tlb, just add it to the references
of the project, it was probably too easy for me at that time:-) But
now, i'm still stuck as there is no doc about using the interfaces and
classes of this activex to control labview.
The example given on your link is made is C++ and for some reasons,
the wrapper generated for Labview.tlb when i added it to my c# project
doesn't seem to expose the same
interfaces and classes as the one used
in the C++ example. I therefore can't use the C++ example in C#.
I've tried to do something like:
LabVIEW.ApplicationClass a = new LabVIEW.ApplicationClass();
Just this line causes labview to launch but then immediately throws an
exception: "Query interface for interface LabVIEW._IApplication
failed".
Does somebody knows how to use that control in C#/VB.NET ?

How can i use labview for notebook

Similar Messages

Maybe you are looking for