How can i use modal analysis in labview and Sound and Vibration toolset in my structural studies.

I am working on structural analysis of buildings during earthqauke.I ahve NI 4472, labView, sound and vibration toolset.Now i also want to carry out Modal Analysis. Where can i find thisin NI software.

There are third party software packages that support modal analysis. These include IDEAS from MTS, Smart Office from m+p, and ME Scope. You can use LabVIEW to save a file or export the data directly via Active-X. If you have some specific functions that you would like to see implemented in LabVIEW, drop a note to one of our developers, Hui Shao or myselfat : [email protected] on what you would like to see.
Kurt Veggeberg, BDM Sound and Vibration.
[email protected]

Similar Messages

How can i use activeX Control in labview?

how can i use activeX Control in labview?
please describe me step by step.
thanks.

Well..that was quite helpful..but now I'm encountering certain problems. I've attached the VI I've made.
I don't need sound at the moment so I dropped it. (Although I tried to play it..but all I could hear was a very annoying sound.) Secondly I don't want to display any date or time..so i dropped that property too.
Now when I run this Vi...the webcam turns on, the screen of videocapx pops up..then the webcam light goes off..and another pop up appears saying..labview is not responding..and i have to close it reluctantly.
I haven't placed the stop capture property in this vi. i checked it by placing it too..but that doesn't work.
I would like to notify that my actual task is to acquire image and then compare it with another one already present on my pc. I want you to please help me out..solve my first query then I'll proceed with the latter part.
Attachments:
activexvideocaps.vi ‏20 KB

HT204053 Dear Support Team, every time i tried to logon Icloud its gives me wrong user name or password and at the end it show me error " This Apple ID is valid but is not an ICloud Account" then how can i use one account for same Apple ID and ICloud???

Dear Support Team,
Every time i tried to logon Icloud its gives me wrong user name or password and at the end it show me error " This Apple ID is valid but is not an ICloud Account" then how can i use one account for same Apple ID and ICloud?
Thanks

It is not possible to create a new iCloud account using a Windows machine. You must create the account using a Mac (10.7.5 or more) or an IOS device (iPhone etc). Once that is done you can sign into and use the account on your Windows machine.

How can I use TopLink for querys that have two and more tables?

I use TopLink today, and I can use one table to query, but how can I use TopLink for querys that have two and more tables?
Thank you for see and answer this question.

You can write a custom SQL query and map it to an object as needed. You can also use the Toplink query language "anyOf" or "get" commands to map two tables as long as you map them as one to one (get command) or one to many (anyOf command) in the toplink mapping workbench.
Zev.
check out oracle.toplink.expressions.Expression in the 10.1.3 API

How can i use 2 different apple ids for imessage and facetime on 1 ipad?

How can i use 2 different apple ids for imessage and facetime on 1 ipad?

Do you mean can you use one Apple ID for FaceTime and one for iMessage? You should be able to. Or, do you mean, can you log into iMessage (or FaceTime) with two Apple IDs at once? No.

How can i use in the same time input line and mic to recorder in several track whit SONAR

I have beem recording only input line because SONAR 4 not recognized the mic in, Help me!!!.
Thank you. Sorry for my english

LIMACAR wrote:
How can i use in the same time input line and mic to recorder in several track whit SONAR 4. I have beem recording only input line because SONAR 4 not recognized the mic in, Help me!!!.
Thank you. Sorry for my english
Depending on which soundcard you have there, but if your card is capable for
ASIO -> activate I/O drivers on Sonar/Options/Audio/Drivers -tab (mic/line sources should be listed there --> activate) and select the mic or/and Line sources on tracks "I" - dialog
WDM/KS -> use the Surround Mixer or windows recording controls for recording source selection (mic should be listed there)
MME32 - > same w/ WDM/KS
If you use Asio4All --> same w/ WDM/KS & MME32
No mic and line source simultaenously w/ WDM/KS and MME32.
You perhaps be able to do this w/ kX drivers.
jutapa
ADDED:
You can also install modded version of Audigy 2 drivers/software but I have never done this w/ Li've! 5. so I can't be sure if you get ASIO support for your card.
Here are the instruction --> http://www.tech-pc.co.uk/audigy-2.php
jutapaMessage Edited by jutapa on 05-25-2006 02:48 PM

How can I use USB interface in Labview?

Hi.
Does labview allow to USB interface?
I have been seen allowing GPIB and RS232.
I'm beginer at Labview and wanna use USB interface for my target system and pc.
I wanna know how to labview interfaces from target system to pc.
And if Labview doesn't provide USB interface module, how can I use USB?
Is using a USB at Labview hard to beginer?
Plz, answer to my quetion.
sorry, my English is very poor.
thx for reading my article.

You can access devices connected to the USB port, but not in the same way as you would a GPIB or RS232 device. There are no USB drivers like there is VISA for GPIB or serial. Rather devices that plug into the USB appear to the systen as some sort of standard resource like a printer, disk drive or IO board. LabVIEW then interacts with these devices as it would any other device of the same type.Look at it this way, if you have a USB daq device you will access it through MAX the same as if it were a plugin card. Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

HT204380 how can i use face time with my ipad 2 and my wifes ipad mini if we both got the same apple id

how can i use face time on my ipad 2 with my wife on her ipad mini if we both got the same apple id info

Add another email.
http://i1224.photobucket.com/albums/ee374/Diavonex/Album%201A/45059983711d586099 0cb799efad0bb8_zpsd520c0d4.jpg

How can I use local variable in LabVIEW-Action?

Hi All!
There is local variable (for example "MyVariable") in local scope of project. There is Action-step, created by LabVIEW. One of input terminals step is "Sequence Context".
How can I access to MyVariable by Sequence Context? Unbundle? It does't work.
Thank you.

On the TestStand palette there is a VI called TestStand - Get Property Value.vi. Use that. Attached is an image showing how to use it. The trick is making it produce the correct data type. Do that by right clicking on the VI and selecting Select Type. Then you can choose the type. I think in LV 2010 and TS 2010 it is a polymorphic VI and you can just change it. I wrote an example here for Chaz: http://forums.ni.com/t5/NI-TestStand/How-to-execute-two-steps-in-parallel/td-p/1449874
It's the second example that's attached.
Hope this helps,
jigg
CTA, CLA
teststandhelp.com
~Will work for kudos and/or BBQ~
Attachments:
AccessLocalVar.JPG ‏67 KB

How can i use NXT toolbox in labview?

Hi i am newbie in labview and trying to get Lego RFID communicate with labview.
But i couldnt get it done. because i could not understand how to connect each other toolboxes.
there is no describtions for newbie, but words what i cannt understand, like buffurs thing. T.T
attached file is the .vi file what i messed up and plus, somebody's RFID circuit which i can not use.
please save me.... T.T
Attachments:
RFID2_NXT.vi ‏37 KB

Please post to the Mindstorms board - http://forums.ni.com/t5/LabVIEW-for-LEGO-MINDSTORMS-and/bd-p/460
You can click on Options and request the moderator to move this.

How can i use multi threading in labview?

i want to run a Digital storage oscilloscope and an energ ratio meter simultaneously using labview. i am using GPIB interfacing and windows XP. how can i do this using multi threading. Bot the instruments shd run and give data at the same time.

You can't do this - at least not with a single GPIB board. It has nothing to do with threading or LabVIEW. There can only be one talker at a time over the bus. Depending on the instruments, you could probably set them up to take measurements simultaneously but you have to sequentially poll them to get the data.

How can I use my Macbook without worsening my arm and hand injuries?

I have had arm and hand injuries i.e. rsi/repetitive strain injuries for the past 3 1/2 years and coordination problems all my life. I have pain after doing too much with my right hand, I have trouble doing anything with my left hand, and I have worse trouble doing anything which requires both hands at once or alternately. I have trouble using touchpads and touchscreens, but the ones on the Mac work all right, as long as I don't enable tapping or complex gestures. I use an external vertical mouse. I don't have trouble with clicking, though I do have trouble with getting to the right spot with small buttons and narrow scrollbars.
I tried dictation to help with writing, but it requires a lot of editing. I don't know whether I should just try to get the hang of dictation or just ignore it. I don't know of anything similar to help with organizing files.
I imported files from an older Mac and an older Linux machine last spring. I had a lot of trouble with the imports, and ended up with a lot of duplicates. I used DupeGuru to clean some out, but DupeGuru itself requires a lot of painful careful selection, and sorting and reorganizing folders requires a lot of painful work.
I made the mistake of trying to import my pictures folder into iPhoto too, I am not sure how to fix that.

Marja E wrote:
One more thing: I have a lot of trouble renaming files, especially in the finder. I have to click and click again, and sometimes it ignores the second click, and sometimes it opens the file or folder, and only sometimes it lets me rename things. I wis there was an easier way, because it is hard.
Select the file, then hit the <return> key. After you have made your changes, hit the <return> key again.
While the name is in edit mode, you can use up-arrow to move to the front of the name, and the down-arrow to move to the end of the name.

TS1253 I am connected to internet through modem. How can I use Time Capsule as a wreless harddrive and connection to USB printer

Can I use a Time Capsule as a part of my network> I am connected to internet through modem and want to use Time capsule as a wireless harddrive and wireless connection to usb printer. How can I do that? Please help

This type of setup is not officially supported by Apple.
It might be possible to configure the Time Capsule this way, but please take a minute to consider a few things that you may not have thought about, as this is...frankly....the worst possible way that you could configure the Time Capsule.
Wireless backups will take twice as long as normal wireless. Why? The signal must make a "double hop".
Hop "one" would be from your Mac to the wireless router, then the signal must make hop "two" to get back to the Time Capsule.
In addition to doubling the time for backups to occur, this doubles the chances for an error to occur during a backup.
The Ethernet ports are not enabled at all on the Time Capsule when it is configured this way, so backup over much faster Ethernet is not possible.
The USB port is enabled, so assuming that the printer is compatible, it could be configured to connect that way. Keep in mind that only printing is supported. If you have an All-in-One device, advanced functions like scan, copy, maintenenance will not be supported.
So, do you really want to try this? There are no guarantees here that things will work at all.

How can I read in a TDMS file into Sound and Vibration Assistant

I have recorded a signal from 2 channels from a PXI 4496 DAQ card. I recorded this signal with the TDMS file format from a VI in Labview. I would like to import these signals into the Sound and Vibration Assistant for freq. analysis. In sound and vibration assistant there is an import logged tdms from signal express but I can not seem to import my original signal? How can I import this data?

Hello All,
I am trying to read TDMS file using LABVIEW. The TDMS file is created by me for reading data from one wire devices.
I have created simple vi. attached below which read data from TDMS file. I am able to read other tdms files, I have with this program but not which one created by me. I am not able to attach file with .tdms exentiont. So I have attached it with .xlsx extention. Can anyone please guide me where is the problem in TDMS file? Am I missing anything while creating it?
Thanks
Attachments:
EditTDMS (1).vi ‏14 KB
data.xlsx ‏17 KB

PCI 6602:How can I use the digital lines of the board and in the same time to generate pulse train using a counter?

Hello!
My problem appeared when I tried to update my code from Traditional NI-DAQ Legacy to DAQmx.
I am using 2 counters (counter 5 and counter 7) from PCI-6602, to generate pulse train, and also the Digital I/O lines of the port 0 (the lines form 0 to 7). What I do in my application is that I am starting to generate the pulse train on the output of the 2 counters, and after that I am playing with the state of the digital lines.
In traditional there was no problem using the counters and the digital lines in the same time, everything was going perfectly, but in DAQmx this is not possible.
What happens: I start to generate pulse train on the output of the counters, no errors encountered, but when I try to modify the state of one line of the digital port the generation of the pulse train is stopped. This is happening when I start the task associated to the digital port.
My question is: it is possible to create a channel on the digital lines without altered the channels created for the counters?
Another thing what I manage to see using the "Measurement & Automation Explorer" and Test panels for PCI-6602, basically is the same thing, I generate pulse train on the output of the counter 7 and try to start a task on the digital line, but I get one error :
"Error -200022 occurred at Test Panel
Possible Reason(s):
Measurements: Resource requested by this task has already been reserved by a different task.
Device: Dev4
Terminal: PFI8"
Instead if I use the counter 0 or counter 1 to generate pulse train I don't encounter the same problem.
Which resources are used by the counters 2 to 7 from the PCI-6602 board and the counters 0 and 1 do not use?
Thank in advance for any replies!
Ciprian
Solved!
Go to Solution.

Hello Jordan, thank you for your reply.
I am sorry but I can not see or run your example, I don't use LabView, I use Visual C++ for developing.
Here is the code for generating the pulse train:
GeneratePulseTrain(unsigned long ulCount1, unsigned long ulCount2)
    short nStatus = 0;
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    nStatus = DAQmxCreateCOPulseChanTicks (m_taskHandle, "Dev4/count5", "", NULL, DAQmx_Val_Low, 0.0, ulCount1,ulCount2);
    if( bTriggerMode == true) // if hardware trigger is enabled
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_ArmStartTrig_Type, DAQmx_Val_DigEdge);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Edge, DAQmx_Val_Rising);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Src,"Dev4/PFI17" );
   //set the internal timebase
   nStatus = DAQmxSetCOCtrTimebaseSrc(m_taskHandle,"Dev4/count5","20MHzTimeBase" );
   nStatus = DAQmxStartTask(m_taskHandle);
    return nStatus;
And the code where I try to set the digital line:
SetChannelState(short nState)
    short nStatus = 0;
    uInt8 wrtBuf0[1]={0};
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    // Configure line as output
    nStatus = DAQmxCreateDOChan (m_taskHandle, "Dev4/port0/line0", "", DAQmx_Val_ChanPerLine);
nStatus = DAQmxStartTask(m_taskHandle);
    wrtBuf0[0] = nState;
    nStatus =DAQmxWriteDigitalLines (m_taskHandle, 1, 0, 0, DAQmx_Val_GroupByScanNumber , wrtBuf0, NULL, NULL);
    nStatus = DAQmxWaitUntilTaskDone(m_taskHandle,10);
    nStatus = DAQmxStopTask(m_taskHandle);
    nStatus = DAQmxClearTask(m_taskHandle);
    m_taskHandle = 0;
    return nStatus;

How can i use modal analysis in labview and Sound and Vibration toolset in my structural studies.

Similar Messages

Maybe you are looking for