How Clean ip Route Table and configuration

How Clean ip Route Table and configuration?
Cisco have any best practice?

Hey Juan,
your question is not very clear but i believe you want to know how to clean ip route table and configuration. So:
1. Cleaning IP routing table - clear ip route * - This will refersh the routing table.
2. Cleaning configuration - It depends on the device however in most of Cisco devices you may clear the startup configurtion and its done :)
HTH.
regards,
RS.

Similar Messages

  • Multiple routing tables and/or policy routing

    Hey all,
    I'm trying to configure a Mac Mini (10.8) for multiple routing tables and policy routing.  This server runs Ostinato, a freeware traffic generator.  My purpose is to generate traffic on multiple VLANs towards different gateways and different destinations.  To that end, I have VLAN tagged the (only) Ethernet port and configured 5 VLANs on it.  The first one has the default route (I manage this Mac over this VLAN).  The other four have IP addresses in the test range I'm using. 
    The goal is to have traffic sourced from IP-address-X go out vlanX towards gateway-X.  It's counterpart on the far end runs Linux and I have configured it in this way:
    ip route add default via <gateway-X> dev ethX table X
    ip rule add from <network-X> table X priority X
    Researching on OpenBSD forums (since it's the base of MacOS X), provided this:
    route -T X add 0.0.0.0/0 -iface <gateway-X>
    echo pass in from <network-X> to 0.0.0.0/0 rtable X | pfctl -mf -
    However, the Mountain Lion "route" command does not support the -T option, so that killed that idea.  Another forum suggested that this would have worked on 10.4:
    ipfw add X fwd <gateway-X> ip from <IP-address-X> to any
    I tried this on 10.8 though the man page says it's deprecated, and (surprise, surprise) it did not work. 
    Any ideas to get this working appreciated!
    Thanks,
    Aaron

    Still doesn't have it in 10.9.4.
    irene:~ cschwartz$ sudo bash
    bash-3.2# route -T add
    route: illegal option -- T
    usage: route [-dnqtv] command [[modifiers] args]
    I'm guessing you want policy-based routing due to VLANs...? If you can get a USB-to-Ethernet adapter, then maybe you can work around this by using multiple physical links instead of VLAN tagging. But if you need source-based routing etc. then no.

  • Can anyone tell me how to setup odbc driver and configure in the setup

    Can anyone tell me how to setup odbc driver and configure in the setup

    You can't switch languages in OS X programs, just in the OS itself. Insert the Leopard OS X disc, and choose your new preferred language when prompted.

  • How to correlate lips table and ekpo table?

    Hi,gurus:
    How to correlate lips table and ekpo table? We want to find the purchase order no. in the delivery table.
    Thanks in advance.

    Hi xinjiang 
    You can try using VBFA table. give input as VBELN = deliver no.,POSNN = item no.and VBTYP_N = 'J' and VBTYP_V = 'V'. Then VBELV,POSNV  will give you the purchase order no. or else you can get all the preceding documents of delivery like sales order and then input sales order and get purchase order from VBFA

  • How to query a table and result together with autonumber

    Hi all
    How to query a table and the result return autonumber for each row together with the table values.
    I have tried rowid but it provide me with characters.
    Tj

    What is your exact requirement?
    If you want the number of rows selected, you can use rownum.
    select rownum, a.* from <table> a;
    Cheers
    Deepak

  • How to ADD reference table and make a field as currency field in dictionary

    pls render some info on how to add refernce table and ref field if i want to make an added field as a currency or quantity field...

    Hi Kiran,
    It sounds like you are creating a "Z" table or structure and have defined a quantity (eg MENGE). But when you run the syntax check, the system is saying you need to define a reference table / field.
    Well when you are in SE11, click on the "Currency / Quantity Fields" tab. You will see 2 columns called "Reference Table" and "Reference Field". These 2 columns define the unit of measure for the currency / qty.
    If you have defined in your table MENGE and MEINS and the MEINS field is the unit of measure for the MENGE field you should define your fields as such (inthe Currency/Quantity Fields" tab:
    Table - ZVBAP
    MENGE MENGE_D QUAN ZVBAP MEINS
    MEINS MEINS   UNIT
    Hope this makes sense.
    Cheers,
    Pat.
    PS. Kindly assign Reward Points to the posts you find helpful.

  • I have bought a wireless router WRT150N and configured it...

    I have bought a wireless router WRT150N and configured it. I have a DSL Cable modem. I am not able to connect to Internet sites (even when connected to the router through cable). I have a VPN client in my laptop and i am able to connect it. after connecting the vpn i am able to browse all the sites. why i am not able to browse the sites without connecting the vpn? If i directly connect to the modem (i.e without router) i am able to browse.
    Is there any configuration settings i am missing out?

    Yes i think you are missing some configuration setings on the router ....
    As it is a DSL connection .... you can use this link to configure the router using DSL connection ....

  • How to join two tables and get the supply delivery date next to order?

    So there are two tables. One has customer's order no, ordered date, order quantity, available quantity and code of article-
    The other table comes form supply side where we have supply order no, article number, ordered qty, and delivery date.
    We keep stock so this can not be MOT (made to order) system.
    What i need is correct date of arrival to appear next to cusotmers spoecirfic order. The older cusotmers order get's the parts first, second oldest order is next in line etc.
    here is any example
    customer's order
    ref order
    art. code
    ordered qty
    available qty
    order date
    1809202491
    700497
    60
    0
    3.7.2014
    1809200528
    700497
    13
    0
    20.6.2014
    1809198640
    700497
    7
    0
    9.6.2014
    supply order
    supply order
    art. code
    qty orderd
    date of arrival
    4501243378
    700497
    50
    4.8.2014
    4501263437
    700497
    20
    6.10.2014
    There is actually a 3rd "table" and that sort of connects the two and that is stock on hand per art. code.
    The main issue is that stock is assigned to purchase orders only when it actually arrives in the warehouse.
    A human can easilly connect the dates of when the stock will arrive and quantities with correct customer's order. In this case the firts order will get 50 pcs in August while 10 pcs will remain on backorders. The missing 10 pcs Will arrive in October. The second order will get 10 pcs in october and 3 will remain on backorders with no delivery date. While the third customer orders does not have a delivery date.
    So how to make the SAP do this calculations and display the arrival date next to date of customer's order?

    I checked the instructions as i do not have access to this part. It seem this is a query. We had issues with queries in the past as not all codes from orders would appear in them. They never found the reason why that is happening.
    However, I think the main issue is that the information here is not connected and is separately provided for supply and for sales. So i doubt it can be connected in this query.
    edit: as you can see the only connection is stock on hand.
    and total number of various items we have is close to 100.000 of various article codes.

  • How to export internal table and pass the internal table to another screen?

    Hi,
    I have a sql SELECT statement that select data from table into internal table. I would like to export out the internal table and pass to another screen and display the data in ALV list. How to export it out? I try but the error given was " The type of "OUT_SELECT_ITAB" cannot be converted to the type of  "itab_result".
    Another question is, how to pass the internal table that i export out from the function module to another screen?
    Here is the code
    ==============================================================
    FUNCTION ZNEW_SELECT_ZSTUD00.
    ""Local Interface:
    *"  IMPORTING
    *"     REFERENCE(IN_SELECT_YEAR) TYPE  ZSTUD00-EYEAR
    *"  EXPORTING
    *"     REFERENCE(OUT_RESULT) TYPE  CHAR9
    *"     REFERENCE(OUT_SELECT_ITAB) TYPE  ZSTUD00
    *& Global Declarations
    DATA: itab TYPE ZSTUD00,
          itab_result TYPE TABLE OF ZSTUD00.
    *& Processing Blocks called by the Runtime Environment
    itab-eyear = IN_SELECT_YEAR.
    SELECT *
    FROM ZSTUD00
    INTO TABLE itab_result
    WHERE eyear = IN_SELECT_YEAR.
    IF sy-subrc = 0.
      out_result = 'Success'.
      OUT_SELECT_ITAB = itab_result.
    ELSE.
      out_result = 'Fail'.
    ENDIF.
    ENDFUNCTION.
    ===============================================================
    Please advise. Thanks
    Regards,
    Rayden

    Hi Nagaraj,
    I try to change it in Tables tab page but it state that TABLES parameters are obsolete. when i "Enter". I try to "Enter" again. it seem to be ok but it stil give me the same error.
    ================================================================
    FUNCTION ZNEW_SELECT_ZSTUD00.
    ""Local Interface:
    *"  IMPORTING
    *"     REFERENCE(IN_SELECT_YEAR) TYPE  ZSTUD00-EYEAR
    *"  EXPORTING
    *"     REFERENCE(OUT_RESULT) TYPE  CHAR9
    *"  TABLES
    *"      OUT_SELECT_ITAB STRUCTURE  ZSTUD00
    *& Global Declarations
    DATA: itab TYPE ZSTUD00,
          itab_result TYPE TABLE OF ZSTUD00.
    *& Processing Blocks called by the Runtime Environment
    itab-eyear = IN_SELECT_YEAR.
    SELECT *
    FROM ZSTUD00
    INTO TABLE itab_result
    WHERE eyear = IN_SELECT_YEAR.
    IF sy-subrc = 0.
      out_result = 'Success'.
      OUT_SELECT_ITAB = itab_result.
    ELSE.
      out_result = 'Fail'.
    ENDIF.
    ENDFUNCTION.
    ===============================================================
    regards,
    Rayden

  • How to update Spry-table and present the updated table in a div element?

    Hello!
    I am using a very interesting AJAX-framework called Spry when designing a web page. Here the web page is: Link.
    I need some help.
    Every time a new project or shift is added, the changes are written to an xml-file. When the page is reloaded, Spry reads data from xml-files.
    This is caused by this code:
    dsProjects = new Spry.Data.XMLDataSet("timetable/projects.xml", "projects/project");
    dsShifts = new Spry.Data.XMLDataSet("timetable/{dsProjects::url}", "project/shift"); //look inside projects.xml and //extrac xml-file. url
    dsName = new Spry.Data.XMLDataSet("timetable/{dsProjects::url}", "project");
    I call this function that I have written: loadProjectsIntoDivElement ().
    This function does the following: [See attached code.]
    It iterates through the Spry-datastructure and puts the data in a table inside of the div-element called 'projectsList'.
    Now, when I add a new project, I want it to be inserted into the Spry-datastructure and then cause the new data to be written into the div element called 'Specials_DIV'.
    I have found out how to update a Spry-datastructure (e.g. dsProjects above), but I don't know how to update the table containing the data without refreshing the page. This should be done using Spry.
    Some code:
    1:
    2:
    3:
    function loadProjectsIntoDivElement () {
    $('#projectsList').html('');
    $('#projectsList').append('<table id="Specials_Table"><tr><th spry:sort="id">ID</th><th spry:sort="NAME">Name </th><th spry:sort="hoursestimated">Nr. of hours estimated</th><th spry:sort="hoursworked">Nr. of hours worked</th><th spry:sort="costperhour">Cost per hour.</th></tr>{function::init_hours}<tr spry:repeat="dsProjects" onclick="chooseProject({ds_RowID})"><td>{id}</td><td>{NAME}</td><td>{hoursestimated}</td><td>{hoursworked}</td><td>{costperhour}</td></tr></table><br/>{function::get_hours}<br/>');
    I have tried to accomplish this in various ways but I don't succeed.
    I want to do it without refreshing the page.
    Update: I found some code here that I will try: Link
    Thanks in advance!
    Anders Branderud
    My blog

    Hello!
    Thanks!
    I don't succeed with the implementation in any browser.
    I have found a way to it, but I would like a way that updates the data quicker and without reloading all of the page. After all, I am only adding one row on the end of the data structure, so there should be no need to read in all data again.
    Now I do it like this:
    When a project is added, do this:
    1. Store a new row in the project file through a php script.
    2. When the post-call to the php-file returns, do refresh of the whole page.
    Then the newest version of the xml file will be read in.
    However, I don't want to read the data from a xml file each time that a new project is created.
    I know how to add the new data to a Spry-datastructure [in my code 'dsProjects'], but I don't know how to display the updated data without reloading the whole page.
    I have tried some various ways to do it, but haven't succeded.
    Thanks!
    Anders Branderud

  • How to use "Routing Table" option in Proxy service in OSB ?

    Hi,
    I have created Business and Proxy services in my OSB console. I have used "Custom Query" option while creating the Database Adapter and I'm passing one input parameter to the query. My input parameter is "Name".
    Based on the input values for this parameter, I need to pass a corresponding values to the query. For example, If I pass the following values to "Name" input parameter (India) I need to pass "Value1" to my query -
    India --> Value1
    China --> Value2
    America --> Value3
    To achieve this requirement, I have used "Routing Table" option. I have specified the values as follows -
    Expression - $body/fet:FetchCustDataInput/fet:Name
    Operator- '='
    Compare value - India
    Service - "My Webservice"
    Operaton- "My Service Operation"
    In the "Request Actions:" I have added the "Add an Action --> Messaging Processing --> Replace" and provided the following values -
    Replace <XPath> = $body/fet:FetchCustDataInput/fet:Name
    in Variable = "Name"
    with Expression = xs:string('Value1')
    and selected "Replace node contents" option.
    No validation errors I faced. I have created the Routing table in Proxy service. But when I try to execute the proxy service in my Test Console, I get the following error message -
    "The invocation resulted in an error: Unknown error while processing message for service ProxyService OSBQueryService/FetchByCustomQuery/FetchByCustomQueryPS."
    I have even enabled "Direct call" and "Include Tracing" options as well. The message under "Tracing" give "(echoing request)
    Routed Service. No Service has been invoked, the request is echoed.".
    Can anyone please help me to resolve this issue.
    Thanks in Advance,
    Udaya

    Did you put any loggers in the proxy at request pipeline prior to route node ? Can you trace if the request has entered request pipeline aleast.
    If not just check the transport headers under the request window in the test console. There should be a text box for entering username/password which should be left blank. I have faced this unknown exception from test console in some browsers where an incorrect username/password used to get populated here. Check this ..
    Edited by: atheek1 on Jul 22, 2010 2:02 AM

  • DBMS_FGA.add_policy .. How to handle multiple tables and multiple users

    Dear All,
    My database is 11gR1 and Linux is the platform.
    I have more then 50 very important tables and around 15 database users.
    I want to implement fine grained auditing on these important tables.
    This is how I am going to implement it:
    SQL>BEGIN
    DBMS_FGA.add_policy(
    object_schema     =>     'Scott',
    object_name     =>     'SAL',
    policy_name     =>     'SALARY_CHK_AUDIT',
    audit_condition     =>     NULL,
    handler_schema     =>     'imran',
    statement_types     =>     'SELECT,INSERT,UPDATE,DELETE',
    audit_column     =>     NULL);
    END;
    what is i have to pass multiple tables in object_schema and multiple users in handler_schema.
    I hope i am able to clear my question, any doubts please let me know.
    Regards, Imran

    Hi,
    object_schema - The schema of the object to be audited. (If NULL, the current log-on user schema is assumed.)
    in case if you like to audit for multiple users - then try to test by holding a null value and test access the important tables -where the relevant auditing records are generated as per your requirement or not. i have not tested.. try it
    - Pavan Kumar N

  • How to include new driver and configure datasource in NW 7.0

    Hi,
    I have deployed my application in the app server and now i need to add the ms sql drivers to the application server and configure datasource to it.
    Can any one help me to configure the datsource in Nw 7.0 and also how to add the driver files tp app server..?
    thanks in advance
    jayakumar

    Hi,
    Follow these links:
    How To Install and Configure External Drivers for the JDBC & JMS
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/f04ce027-934d-2a10-5a8f-fa0b1ed4d88f
    http://saphelp.border-states.com/EN/b3/cc633c3a892251e10000000a114084/content.htm
    http://www.sapag.co.in/JDBC%20Adapter-Type2JDBCDriver%20Deployment.html
    Regards,
    Nithiyanandam
    Reward points

  • How to create Database, table , and apply triiger on oracle10g lite ?

    Hello All,
    I want to use oracle 10g lite , i just download oracle 10g lite from oracle site and just install on my system, i have no any knowledge how to create database, how to create tables and how to apply triggers on tables. I want to access this database using JDBC.
    plzzzzzzzzzzzzzzzzzz help me...............
    Thanks in advance
    Pankaj

    are you trying to use oracle lite just as a database? it is normally used as part of a data synchronisation from a server, replicating snapshots to create the database and tables on the client.
    PL/SQL format triggers are not supported in the oracle lite client. Java stored procedures are, but you would need to build the table interactions

  • How to create certificate authority and configure it for IIS

    Hi
    I Install ADCS role in Server 2012 and configure it. but when i go to IIS and want to create domain certification , the select button is grey .i think i couldn't configure certificate authority correctly. how can fix this problem.
    Whenever you see a helpful reply, click on Vote As Helpful & click on
    Mark As Answer if a post answers your question.
    LinkedIn:
      Facebook:

    Thanks my problem was solved.
    But there is a problem after install IIS and ADCS , i restarted both server but didn't work ,but now(6 hours after restart) it work fine.
    another Question is after i select appropriate certificate authority ,when i click on finish it gives me the following error 
    "the certificate request was submitted to the online authority but was not issued the request was denied"
    Whenever you see a helpful reply, click on Vote As Helpful & click on
    Mark As Answer if a post answers your question.
    LinkedIn:
    Facebook:

Maybe you are looking for