How close can I come to Realtime with Labview student edition and an Arduino project?

Hey everyone,
I'm really new to Labview and just recieved the Labview 2012 student edition and I plan to do a project. It came to my concern that after asking the Labview interface for arduino forums, they suggested that it cannot provide realtime.My project in generalwill consist of two arduinos, one with many sensors close to 30 and the second will have many actuators. My question is whether I can come to develop a realtime crucial system or fast processing speeds. Please provide any input.Your time and responses are much appreciated.

MustafaMX5 wrote:
Thanks for replying, but if I may ask, are you implying that when the arduino is programmed it will run in realtime, however when labview interfaces with it isn't. Then if so would you suggest I just program the arduino and then monitor the system using Labview as my GUI.Lastly say I had the two arduinos already programmed with sensors and actuators and they communicate independently without labview, would labview impede on this time critical system.
Thanks A Lot
Anything on a Windows machine is not real-time. The micro on the arduino is. You can still program in communications between the micro and LabVIEW and not impede on the real-time operation. It will take some cycles away, but probably not enough to worry.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Similar Messages

DAQ with LabVIEW Student Edition

I am in between to choose either LabVIEW 2013 Student Edition and LabVIEW 2013 student Edition Software Suite. The difference is around 40 bucks for me. If the former lets me control devices through serial port and some data acquisition using NI-DAQ-6008, then I can save some money. I have read some other threads and the answer seems positive, but I just need a little more confidence before spending student earned cash!
Solved!
Go to Solution.

For serial communication, you need NI-VISA and for using the 6008, you need DAQmx. Both drivers are free and available from the Support page. The student suite is not at all required if this is all you are doing.

Can I use wireless headphones with my iPod 4G and if so how?, Can I use wireless headphones with my iPod 4G and if so how?

I am looking at be headphones but they're wireless and I was just wandering if I could use them with my iPod without wifi or any Internet connection and if so how?

Yes, but they must use Blue Tooth. You will find many that will work.

How do i get my serial number? - i can't find the packaging of my students edition and unfortunately deleted the e-mail i received. And also is my product not registered in my adobe account, for the registration in my products i need the serial number wit

help

For the link below click the Still Need Help? option in the blue area at the bottom and choose the chat option...
Serial number and activation chat support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html ( http://adobe.ly/1aYjbSC )

HOW CLOSE CAN BEHRINGER TRUTH B2031A SPEAKERS BE TO A 2013 IMAC WITH FUSION DRIVE?

How close can you put studio speakers (specifically Behringer truth b2031a) to a 2013 imac? I know the speakers are sheilded but is it still safe right next to the computer? Will the fusion drive inside or a external be affected by the speakers? Anyone who has knowledge or experience in this topic your information would be greatly appreciated. Thanks!

This was a concern expressed in this thread: Worrying reply to Apples FAQ on new Fusion Drive
However, Apple has since amended the FAQ, clarifying their earlier Fusion confusion.
Therefore I believe the answer is yes, you can add an external USB HD. If Apple would only state that explicitly in this document, it would eliminate all doubt.

My laptop died so I've installed itunes onto another PC and my music is all on an external hardive which is connected to the new PC. How can I sync my ipod with the new itunes and get all the music onto itunes?

My laptop died so I've installed itunes onto another PC and my music is all on an external hardive which is connected to the new PC. How can I sync my ipod with the new itunes and get all the music onto itunes?

You might consider itunes match for moving CDs you've copied into your itunes library if you dont have a way to use home sharing.
iTunes match is an optional service offered by apple that costs about $25 a year. It scans your music library and if it finds music that is already in apple's itunes catalog it'll automatically "unlock"/"store" these in the cloud for you. Items that it does not find in the catalog it'll upload and store these in the cloud for you and you can download them on your devices. See http://www.apple.com/itunes/itunes-match/

How can I copy test plan WITH ITS RESULTS (PASS/FAIL) to other project in MTM??

How can I copy test plan WITH ITS RESULTS (PASS/FAIL) to other project in MTM??

Hi odedn,
Thank you for posting in MSDN forum.
Based on your issue, you mean that you want to copy the test plan with test results from the current team project
to other team project, am I right?
If yes, as far as I know that when we copy test plan with test results to other team proejcts. It is default that
there just will not copy the test plan with test results (pass/fail) to other team project in MTM.
You can refer the following MSDN document’s
what gets cloned, it explained that which objects are copied from the source test plan to the destination test plan.
Reference:
http://msdn.microsoft.com/en-us/library/hh543843.aspx
If you still want to this feature, I suggest you can
submit this feature request:
http://visualstudio.uservoice.com/forums/121579-visual-studio. The Visual Studio product team is listening to user voice there. You can send your idea there and people can vote. If
you submit this suggestion, I hope you could post that link here, I will help you vote it.
Thanks for your understanding.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How I can configure my Time Capsule with my mobile me?

Someone know how i can configure my Time Capsule with my mobile me?... Because i need access to my documents remotely, from any place where I find...
(sorry my bad english)

I think you're referring to the Back To My Mac feature?
Follow these three articles. Most important are the second and third.
http://www.apple.com/mobileme/features/mac.html
http://support.apple.com/kb/ht1109
http://support.apple.com/kb/HT3486

AP proximity? (How close can your AP be to someone else's AP).

Tried doing some searches but cannot find anything...
If you are designing a WiFi system in a building that already has a system (independent to your new system), how much separation between APs should you have? ie. How close can/should you put your AP to an existing AP?
Sometimes because of the building layout you want to go at the same spot, but I know you need some separation. Assume omni, 100mW APs.
Thanks.

You have some valid points. But every-man-and-his-dog has a 2.4 AP and it still works then it will most likely still work even if it's "every-man-and-his-dog +1".
Most importantly the system has to be designed correctly regardless of the existing networks. The better your system is designed to work solo, the better it will perform in an environment with other APs. Yes existing networks will obviously degrade your performance, but you can't really find anywhere in an modern urban environment without seeing a dozen APs from either inside and/or outside your building. The existing network could be dense but if it is not used all that much, the degradation should not be extreme.
Besides, you have say 100 users in the building, they can use system A (existing) or B (my new one). If they have the option of using both/either, then you have 50 on A and 50 on B. Is that much/any worse than having 100 on A? Contention is contention though the extra beacons will add to it. For the users that can only use "B", then they will at least have an option, even though it will be at a slower performance than if A did not exist, at least they have an wireless option now. If "A" did not exist, you could build your "B" network, and 1 week later, someone could build "A" anyway.
1) Don't worry, it's not my money. Most of the existing "high density" areas are low usage private wlans. (P.S. What's the definition of "high density"?).
2) RFID is not part of our application.
3) & 5) This is being accounted for in our designs.
4) If we use Cisco, then I hope it's significant. ;-)
6) Gigabit.
Good discussions.

How I can stop the combo box with list of values from fireing validations

Hi I'm using Jdeveloper 11.1.2.3.0
Using Hr Schema employees table
I Display employees data in af:table
and I make List Of values on Department_id filed to easy change the employee department
and another one on Job_id filed
and Imake them UI Hints as ( combo box with list of values ) in the employeesVO
the problem is when I Select a value from department or jobs ( combo box with list of values )
fires the entire filed validations for mandatory atributes
Note : the af:table Property ( contedelivery) is set to (immediate )
How I can stop the combo box with list of values from fireing validations

check it out.,
http://andrejusb.blogspot.in/2012/09/what-to-do-when-adf-editable-table.html

I would like to know how i can create a bell graph with out using sub VIs, the data that i created consists in 500 readings with values of 0 to 100, i calculated the mean value and standard diviation. I hope some one can help me

I would like to know how i can create a bell graph with out using sub VIs, the data that i created consists in 500 readings with values of 0 to 100, i calculated the mean value and standard diviation. I hope some one can help me

Here's a quick example I threw together that generates a sort-of-bell-curve shaped data distribution, then performs the binning and plotting.
-Kevin P.
Message Edited by Kevin Price on 12-01-2006 02:42 PM
Attachments:
Binning example.vi ‏51 KB
Binning example.png ‏12 KB

How can I record a video with LAbview?

Hi,
I have a question: How can I record a video with labview?
I have a camera (AXIS 221) connected via rj45 on PC. I see the video of the camera in a browser.
And I would to acquire the video in labview.
Could someone help me?
Thanks
Raf

Unfortunately I haven't any experience with this camera. Iguess, you should install API, then crete new VI, place ActiveX container (palette Container->ActiveX) on the Front Panel, then right mouse click, then choose Insert ActiveX object..., then found you camera object and select it and press OK. Then you probably can see image from the on the front panel. Also probably you will be able to get image data in array (how easy is it - depends from the camera API).
If you able to see image from camera in the Internet Explorer, then another method - you can put Microsoft Web Browser as ActiveX object, then you should also see the image. Disadvantage of this method - you will be not able to get image data.
Andrey.

How can I format an HD with System 10.4 and install Leopard Snow?

How can I format an HD with System 10.4 and install Leopard Snow?

You need to partion the hard drive using Disk Utility. On one partition install 10.4. On the other 10.6. As a note I trust you are doing this on a MBP and not a PPC Mac because 10.6 won't install.

How i can associate my app user with database role

In my application (oracle forms application developed in-house - We are using Oracle Forms 11gR2 with WebLogic 10.3.5 ), i want to use "application user" instead of database user.
I have an application users table, actually, i have database users,and of course, menu application works with database roles (It was developed with oracle forms menu module), my question is, How i can associate my application user with database role, for reusing oracle forms menu funcionality?. It's possible?
Thanks,
Edward

user8929172 wrote:
In my application (oracle forms application developed in-house - We are using Oracle Forms 11gR2 with WebLogic 10.3.5 ), i want to use "application user" instead of database user.
I have an application users table, actually, i have database users,and of course, menu application works with database roles (It was developed with oracle forms menu module), my question is, How i can associate my application user with database role, for reusing oracle forms menu funcionality?. It's possible?
Hi Edward
You can do this by assigning the role functionality to the application user. For example
create the table to enter user name.
create table to enter group name.
create table to assign user to group.
assign role to group.
assign functionality for the user by coding.
hope this helps

How we can use forms HTML capabilities with Oracle Applications?

Hi
Could not find any specific doc how we can use forms HTML capabilities with Oracle Applications?
Thanks

I'm not sure that I understand exactly what you are asking?
What are you trying to do? If you could give a detailed explanation then we can try and assist.
Reagrds,
Bren

How close can I come to Realtime with Labview student edition and an Arduino project?

Similar Messages

Maybe you are looking for