How come my dvd studio pro 3 is not working properly with leopard? Need help!, How come my dvd studio pro 3 is not working properly with leopard? Need help!
I recently installed os leopard on my power MAC G5 and my DVD studio pro 3 application is not working properly as it used to be. I was unable to create motion menu and build the dvd properly. Then I deleted and reinstall dvd studio pro 3, but it did not solve the problems. What should I do?
I have a sneaking suspicion it won't work in 10.5.x, possibly because of the version of Quicktime...
System Requirements:
Mac OS X v10.3.2
733 MHz or faster PowerPC processor (G4 minimum) and AGP graphics card
256 MB of RAM (512 MB recommended)
20 GB available disk space
8 MB of video memory (32 MB recommended)
QuickTime 6.5
DVD drive required for installation
I think your going to need a dual boot Mac with 10.4.x on another drive or partition.
Similar Messages
-
I have a DVD Acrobat Pro 9. I upgraded laptops and trying to install but the DVD is not readable. How can I get a new DVD or Download Acrobat Pro 1. The product is registered and I have the serial number. PS: Contacting Adobe on this issue is impossible... direct support stinks.
Download AA 9 Pro from http://helpx.adobe.com/acrobat/kb/acrobat-downloads.html. Make a new backup for your archive. You might also take the DVD to your library to see if it is a drive problem. You might also carefully clean the DVD with water and soap (do not use anything that would scratch the surface or you have destroyed it for sure) and see if that solves the problem. This is particularly an issue if you have finger prints or other crud on the DVD. However, it could also be a bad drive as I mentioned. Hopefully the download solves your problem in any case (I would backup the download to CD and/or backup HD).
-
great, but my MBA did not come with an installion disc, only a tiny jump drive that is not recognized by windows; and I can't get the contents of that burned to a DVD either. So how the heck do I get the drivers into Windows 7? My MBA has bootcamp 3.0.4.
Here's what I get:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0 mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:11:24:7d:e7:1e
media: autoselect (none) status: inactive
supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::211:24ff:fe28:2e71%en1 prefixlen 64 scopeid 0x5
inet 169.254.115.141 netmask 0xffff0000 broadcast 169.254.255.255
ether 00:11:24:28:2e:71
media: autoselect status: active
supported media: autoselect
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 2030
lladdr 00:11:24:ff:fe:7d:e7:1e
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex> -
Is this now where to ask DVD Studio Pro questions? If not, please let me know where. Here's my question: Using DVD Studio Pro 3, when trying to burn a disc which is 4.5GB, I get error message "Not eough disk space in target folder". What to do?
Thanks. Unfortunately, I need to make a master DVD that can then be duplicated in bulk as a single layer disc. This surprises me because I tried burning a different DVD project that has worked in the past which is also 4.5 GB and now I could not burn that either. I also reencoded some material to get the new project down to 4.4 GB but it still would not burn. Any ideas are appreciated.
-
NEED HELP - how do i lower the burn rate to 1x in DVD Studio Pro 4
Ok, i made a (2) master copies of a DVD-R (Verbatim) in Studio Pro 4 and sent it to a duplicator and I got a call saying there was unreadable data on the discs.
He then asked me to lower the burn rate to 1x. I can't figure out how to do that. Where do I do that? Please help. Have a deadline!!!
Thanks.Dave
You cannot change the burning speed in DVDSP. It will always use the max speed available. To control the burning speed you need to create a disc image of your project and burn it with Disk Utility or Toast.
Read this tutorial about * Creating Disc Image in DVDSP *.
Hope that helps !
Alberto -
I am trying to troubleshoot a slow iMac. EtreCheck showed that com.adobe.CS5ServiceManager.plist failed. Not sure if this is important or how to fix. Any suggestions?
BobHarris: Thanks. The EtreCheck output follows:
Problem description:
My iMac is very slow.
EtreCheck version: 2.2 (132)
Report generated 4/22/15 2:28 PM
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
iMac (21.5-inch, Mid 2010) (Technical Specifications)
iMac - model: iMac11,2
1 3.06 GHz Intel Core i3 CPU: 2-core
4 GB RAM
BANK 0/DIMM0
Empty
BANK 1/DIMM0
Empty
BANK 0/DIMM1
2 GB DDR3 1333 MHz ok
BANK 1/DIMM1
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: Unknown
Video Information: ℹ️
ATI Radeon HD 4670 - VRAM: 256 MB
iMac 1920 x 1080
System Software: ℹ️
Mac OS X 10.7.5 (11G63) - Time since boot: 2:36:57
Disk Information: ℹ️
ST3500418AS disk0 : (500.11 GB)
disk0s1 (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 499.25 GB (372.93 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
OPTIARC DVD RW AD-5680H
USB Information: ℹ️
hp psc 1300 series
Apple Internal Memory Card Reader
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
LaCie LaCie Hard Drive Quadra 1 TB
disk1s1 (disk1s1) <not mounted> : 32 KB
Partition 1 (disk1s3) /Volumes/Partition 1 : 333.27 GB (31.07 GB free)
Partition 2 (disk1s5) /Volumes/Partition 2 : 333.27 GB (84.70 GB free)
Partition 3 (disk1s7) /Volumes/Partition 3 : 333.27 GB (36.70 GB free)
Apple Computer, Inc. IR Receiver
Apple Inc. Built-in iSight
Startup Items: ℹ️
HP IO: Path: /Library/StartupItems/HP IO
Startup items are obsolete in OS X Yosemite
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist [Click for support]
[loaded] com.adobe.CS5ServiceManager.plist [Click for support]
[loaded] com.coupons.coupond.plist [Click for support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Click for support]
[not loaded] com.adobe.SwitchBoard.plist [Click for support]
User Launch Agents: ℹ️
[loaded] com.adobe.AAM.Updater-1.0.plist [Click for support]
[failed] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist [Click for details]
User Login Items: ℹ️
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Microsoft AU Daemon Application (/Applications/Microsoft AutoUpdate.app/Contents/MacOS/Microsoft AU Daemon.app)
HP IO Classic Proxy 2 Application Hidden (/Library/Frameworks/HPServicesInterface.framework/Versions/B/Runtime/HP IO Classic Proxy 2.app)
HP IO Classic Proxy Application Hidden (/Library/Frameworks/HPServicesInterface.framework/Versions/A/Runtime/HP IO Classic Proxy.app)
Director Docker Application (/Applications/Hewlett-Packard/HP Photo and Imaging Software/HP Photo and Imaging Director/Director Docker.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 17.0.0.169 - SDK 10.6 [Click for support]
CouponPrinter-FireFox_v2: Version: 5.0.3 - SDK 10.6 [Click for support]
Flash Player: Version: 17.0.0.169 - SDK 10.6 [Click for support]
iPhotoPhotocast: Version: 7.0 - SDK 10.7
JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
QuickTime Plugin: Version: 7.7.1
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Growl [Click for support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
3% fontd
2% WindowServer
0% coreservicesd
0% mds
0% blued
Top Processes by Memory: ℹ️
78 MB mds
41 MB Finder
33 MB mdworker(3)
29 MB WindowServer
29 MB Dock
Virtual Memory Information: ℹ️
2.60 GB Free RAM
1.40 GB Used RAM
0 B Swap Used
Diagnostics Information: ℹ️
Apr 22, 2015, 11:38:18 AM /Users/[redacted]/Library/Logs/DiagnosticReports/helpd_2015-04-22-113818_[redac ted].crash
Apr 21, 2015, 02:37:28 PM /Users/[redacted]/Library/Logs/DiagnosticReports/Adobe Premiere Pro CS5_2015-04-21-143728_[redacted].crash
Apr 22, 2015, 11:51:45 AM Self test - passed -
I have been making back ups on a Seagate Back up plus drive on a macbook pro running on Mountain lion. Sadly the mac was stolen and all I had was the seagate back up. I tried opening it on my old iMac running on snow leopard and after several visits to this forum managed to open it. The data was safe and sound. Now I have received a hand me down macbook pro which runs on osx 10.9.5. I'm assuming there is a compatability issue as the drive does not come on at all when I hook it up to the usb port. I checked the seagate drive once again on the imac and its light came on on that system. Then I suspected there may be a problem with this macbook pro usb port. But it seemed to work fine when i hooked my camera cord into it. Is it that I must reinstall mavericks. In which case how do I back up before reformatting or reinstalling. BTW I did the command+ R thingy and repaired my internal Hard disc which was showing errors. What do I do next, your help is most appreciated if you have had a similar problem.
Your 2010 MBP would be able to handle Yosemite, but I would strongly suggest that you get the current problem sorted out before trying to upgrade to Yosemite. I'd also recommend another backup that isn't created by Time Machine if you are thinking of upgrading. SuperDuper and CarbonCopyCloner can make bootable clones of hard drives. If you clone your existing system to a fresh external drive, you would be able to boot from that drive and recover quickly in the event that your Yosemite upgrade didn't work out. Time Machine backups are not 100% reliable.
It's possible that, if your internal HD is the one that shipped with your MBP in 2010, it may be failing. If it keeps needing repairs, that is probably a sign that it is approaching the end of its useful life.
Have you run Disk Utility's Repair tool on the external drive as well?
I mentioned the hub because some people have reported here that attaching their USB 3 drives through a USB 2 hub solved some disconnection problems. A good-quality powered USB 2 hub won't cost much.
My most recent brush with random disconnections involved a nice new OWC drive enclosure. I used the cable that came with the drive, but the drive kept disconnecting. Using a different cable solved the problem. You wouldn't expect that what appeared to be a high quality cable would be a problem straight out of the box, but it was. -
I am new to iMovies. When I make a video using the mic and camera in my Macbook Pro, the audio and video are not in synch. Very annoying. How can I fix this?
DVD drives read the bottom of the disk, not the top. Smooth out the paper & try again.
-
I had Premier pro given me by the college I attend and do no use wi fi and do not use cloud. My laptop completely died and will be sent back to Apple for exchange. How can I reinstall Premier Pro on a new Apple computer since the old one is completly dead and could not be unregistered?
Hi,
You have not specified which version of Premiere Pro was given to you. If you don't have the disc (which i suppose you don't have) you will have to download it online.
As far as your registration is concerned, for Premiere Pro CS6 or earlier you will have to reach Adobe chat support for further help: http://helpx.adobe.com/contact.html
For Premiere Pro CC and later, you will not have much problems reactivating it.
Thanks,
Rameez -
I recently updated my MacBook Pro to the new software, and now my iMessage and my FaceTime are not connected with my phone number like it is supposed to be. How do I get them to match so that I would be able to use my cellphone number on my notebook?
To reset any OS X program just go to the folder and trash the affected files.
Open a new Finder Window
Click "Go" in the above status bar
Click and HOLD the "option/alt" key and you will see "Library" now show in the above list
Click Library while still holding the option/alt key and a new window will open with all of your system files
Go to the preference file (NOT Preference Panes)
Locate a file named <com.apple.FaceTime.bag.plist>
Locate another file named <com.apple.FaceTime.plist>
Locate the file <com.apple.iMessage.bag.plist>
Drag the files to the trash
Delete the trash
Close FaceTime and iMessage if not already closed
Relaunch FaceTime and iMessage from Applications folder
This should reset the program back to default. You will have to put your information back into the program but it should work.
Good Luck. -
Just brought home newly purchased MacBook Pro 15"/Maverick/Retinal Display. To my astonishment, there is NO DVD slot! No one in the store told me about this missing feature. Intolerable, How does one install software? Insert CDs to copy for iTunes?Do I have to purchase an external DVD drive? Is one even available? What a crock!
I’ve owned Macs since 1990 (IICX my first), mostly desktops. Having had DVD/CD drives in all my previous laptop Macs since 2001 - (2) G4 Powerbooks, A 17” Mac Book Pro - and also inspecting a friend’s year-old Mac Book Pro which had the DVD slot - unless someone told me at purchase, I had no reason to know that the Retina display version of the 15” had NO DVD drive. ANYHOW, I fully intended to buy the non-Retina display version, because it was cheaper. Unfortunately by the time I got to the Apple store they were no longer selling the non-Retina display version; all versions were ONLY with the Retina display. And the fine distinction of a DVD vs. a non-DVD drive was not pointed out. So now I have to shell out an additional $80 bucks for an external SuperDrive.
-
I am buying a new macbookpro which comes with Lion. Lion has Quicktime X. Logic Studio comes with Quicktime Pro 7. Do I have to download Quicktime 7, or will Logic Studio work fine with the Quicktime X player? Will there be a Quicktime Pro X soon?
your new lion-machine should have quicktime 7, too. if it doesn't, and if it doesn't show up after you migrated your stuff from you old machine you can always reinstall it from the logic dvd's, it's part of logic. my recommendation is to always use quicktime 7, since it's got many features that are absent in quicktime x. quicktime x is nothing but a polished video player. in quicktime 7 (pro, comes with logic) you can even do edits and paste your music onto video files. i use it all the time, especially since logic 64bit doesn't export to video anymore.
-
More details about the problem : My computer is a Mid 2012 Mac Book pro 2.9GHz i7 processor with 8GB RAM updated to OS X v10.8.5
- I ran a compleet scan of my computer for any threats ( I used virus barrier express ) and there was nothing identified
- When I oppened the Activiti Monitor there are about 20-30 processes which I do not undersatand they are run under the user "root" 2 in perticular ( Kernel_task & fseventsd ) they both take up a lot of threads and kernel_task is constantly using 1.2 GB of "real memory" which is at least 20 times any other process that is running espesially the ones that run under the user "Apple" I do not know if this is causing the problems on my mac but i tryed to forces close it and it dose not even let me click the button, the others close but reopean immideatly. I will attach a screen shot of what i have mentioned here.
- The problems I am facing are mainly performance :- To state a few examples, my mac dose not seam to be able to handile even the smallest tasks like switching tabs on safari, typing any thing, playing a movie withought stopping inbetween, etc.. ( let me elaborate on why I said its not able to handil these tasks, it is because when I am trying to do any one of the afformentioned tasks inbetween the cursor becomes a rainbow collered spinning disk and I am unable to do anything for about 10 seckonds after which it starts to work again for some time before it happens again. )
- Another concern of mine is that my mac seems to be on even with the lid closed if I do not shut it down compleetly, if i just close the lid after some time the computer starts warming up, and the fan starts running. the battery is drained at the same rate or slightly less rate than it would have if i was using it normally with the lid opean. ( altough this is happning the screen dose not turn on untill the lid is opean again )
- I have only 300+ GB full out of my 750GB so i believe these are not issues caused by my mac's memory being full ( BUT THE FIRST TIME I NOTICED THIS WAS HAPPNING WAS WHEN MY MEMORY WAS ABOUT 720GB FULL WHEN THESE ISSUES FIRST AROSE I IMMEADITLY DELEATED 400+GB OF MY USELESS FILES THAT I HAD BEEN HORDING ALL OF WHICH WERE MOVIES ) that about covers it all PLEASE LET ME KNOW IF ANY ONE KNOWS WHAT TO DO.
Ps: I apoligize if I have given too many unrelevant details, not enough usefull information and or if i was just all over the place with my explanations but I am really frustrated and was hoping not to miss anyting. Please let me know if any information at all is required and ill do my best to provide it.
Thank YouStart with this comprehensive troubleshooting article:
https://discussions.apple.com/docs/DOC-3521
Look at this one for possible solutions:
https://discussions.apple.com/docs/DOC-3353
Ciao. -
Can I print web pages from firefox using adobe pro 9 (Not using PDF download) and if so how
Can I print web pages from Firefox 3.6.12 using adobe pro 9 (not using PDF Download) and if so how.
{Ctrl + P} - do you have a PDF Printer listed in the Printer - Name drop-down?
-
I wonder how pro photographers use aperture?I shoot raw and my harddrive is alreay full.I'm not able to import new pictures. I don't know what to do. I created a vault. My plan was to create a vault(put all my master files into an external harddrive) and then delete all my projects in my mac pro's harddrive. Is it the correct way to do it ? What should I do if I have thousands of raw files ? How should my workflow be? Can I use an external HD and use aperture through the vault,without keeping the master files on my computer's hard drive?? Or should I shoot raw+jpeg and store raw files in an external backup harddrive and import only jpegs into my aperture library?
There's a bit to learn. It will slowly make sense.
Aperture is an empty field. You're given a tractor and a whole bunch of attachments. What you grow, how, and where, is entirely up to you.
Vaults are for back-up and only for back-up. They have nothing to do with storing your working files.
When your Library outgrows your system drive (and for good performance, you should leave c. 20% of every drive empty), it's time to convert some of your image's Masters from Managed to Referenced. ("Managed" and "Referenced" refer to Masters, not to Libraries.)
There are hundreds of posts in the forum, and several pages in the User Manual on using Masters.
Many people run Aperture with the Library on their system disk, and most (or all) of their images' Masters on external FW drives. This is a good set-up. Note that you will likely have to take steps to back-up the data on your external drives.
If you do the above, there should be no reason to delete any Projects.
The choice of RAW or RAW+JPEG or JPEG depends on the kind of work you are doing. I capture RAW only -- but I don't do any commercial shoots. Pros on deadlines report that the RAW+JPEG works well for them. Capture JPEG if it saves you time. IMHO, there is not a good reason to shoot JPEG to save space (space is cheap; time expensive).
Short-term solution: buy and use a FW800 external 1 TB drive, formatted "Mac OS Extended (Journaled)", and using Aperture relocate the Masters of all images older than 30 days to that drive. (Be sure to change your back-up strategy to include this new drive; you may need a second new drive.)
This general post of mine might help you understand more about Aperture. -
I reinstalled iPhoto on my MacBook Pro. It opens, but only shows the loading bars and does not allow me to add pictures. How can I fix this?
Mac 101: File Sharing
Mac OS X 10.7 Help: Transfer files between two Mac computers
Mac OS X 10.7 Help: Set up a Windows computer to share files with Mac users
Mac OS X 10.7 Help: Use iDisk to share files
Mac OS X: Sharing your files with non-Apple computers
How to share a Mac's files with a PC and vice versa.
Maybe you are looking for
-
Query Regarding the Oracle PL/SQL Developer OCA
Hi All I am planning to go for the certification "Oracle PL/SQL Developer OCA " But I am not sure what is value of this certification in market. Please help me out. Thanks in advance Amit
-
Interconnect ip is not visible in /etc/hosts !!
Hi, all. The db is 11.2.0.3 on a linux machine. (2-node RAC) select * from v$cluster_interconnects; NAME IP_ADDRESS IS_PUBLIC bond1:1 122.254.188.11 NOThe 122.254.188.11 ip address does not exists in /etc/hosts. Does this mean mis-con
-
Drop down list created by fireworks MX disappears behind Flash movie. Is there a way to have the menu list displays in front of Flash movie, pls. let me know what I should do to have the drop down menue not disappear behind the Flash movie. Thanks,
-
iPod touch 5th gen will only sync to iTunes using an old lightning cable that it's falling apart, will charge with another cable but it won't sync to iTunes already try reset and restore same results..I also update everything using a Mac mini and lat
-
CREATE TABLE 'geodata' ( 'Id' char(16) NOT NULL, 'Type' smallint(6) DEFAULT NULL, 'Description' varchar(200) DEFAULT NULL, 'Url' varchar(400) DEFAULT NULL, 'Location' point DEFAULT NULL, PRIMARY KEY ('Id') ERRO