How configure Airport Extreme Base Station M8440

Hi, my problem is:
I bought this Airport Extreme Base Station and I´m having lots of problems trying to get it configured, I have tried with the Mac's Airport Utility, with the Windows version too, also with the AirPort Extreme Admin Utility v3.2 on Windows but nothing. This Airport was working but I wanted to change the SSID and the access key but I just can not, I want to know what can I do to configuring it as a normal router. Thanks in advance.
Isaac

I also have this base station- I found it new in the shrink wrap at the thrift store for $2.
I have a small house, so I don't really need an 'extreme' network.
I have a macPro running 10.6.4.
I also downloaded that app AirPort Admin Utility for Graphite and Snow 4.2.5, and read the accompanying article Mac OS X 10.5: Can't configure a supported Apple Wireless device using AirPort Admin Utility for Graphite and Snow.
I did get info and checked the "open using rosetta" checkbox, only to get the message "You can't use this version of the application AirPort Utility for graphite and snow.app with this version of Mac OS X."
The newer Airport utility cannot see the device, although i can choose it from my airport icon, and join the network.
I am using it to connect right now, in fact. The problem is, I cannot admin the network, rename it, or give it a password, so all my neighbors can use it now also if they wish.

Similar Messages

Cannot configure Airport Extreme Base Station

I have a base station in my classroom. It was plugged in 4 years ago stock, and it has run fine as is all this time. I started to get annoyed about temporary signal drops that occurred from time to time. I was told that updating the firmware would limit these (but not eliminate them)......and now my problem. I tried both airport utilities to no avail. Both give me error messages ("an error occurred reading the configuration") when every I try to set it up. I did a hard reset, but that did not alleviate the problem. I know the default password is "public".....not sure what to do from here. Any suggestions?
The base station is running firmware 5.0.3....which is quite old. My laptop is a G3 iBook running 10.48.
Interestingly the router still works pretty well.....I am using it right now to get on my school network...but I would like to put a password on it and update the firmware.
Thanx
Shawn

Shawn, I'm having the same problem, exactly. I had to disconnect my networked HD for a while (renovations) and when I plugged it back in, I couldn't see the ethernet port. When I went to Airport Admin. Utility, I couldn't configure the airport base station.
I went through the "cold start" procedures and used "public" but to no avail. I still have access to the 'net but am concerned that my security has defaulted to -0-.
I am going to try to direct connect tonight when I get home, but if you have luck, would you please post your answer? I will do the same tonight if I figure it out.
I've been pulling my hair out for a week trying to figure this out!!
Good luck.
Thanks,
Dave

How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
Can you advise on the best set up for this please?
My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
Thanks in anticipation.

The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

How do I find a hard drive connected to Airport Extreme Base Station?

*Apple Says:* "If your base station supports it, you can connect a USB hard disk to the USB port on your base station and computers on your network (both wired and wireless) can connect to it to access, share, and store files and data."
Cool. So I followed the instructions. The drive is recognized by the base station and listed in the Airport Utility. It looks like it's ready to go...
So... How do I access the drive? I don't see it on my desktop, it's not under network. I've tried "Connect to server..." and browsing, I can't see the drive, anywhere. Yeah, I've searched the crap out of this issue on google and this message board as well as apple support knowledge base. I'm sure this is a simple issue and I'm just missing the obvious. Help me out.

Hello Timothy Uhl. Welcome to the Apple Discussions!
Try the following to mount the disk...
o Click on the Desktop to enter Finder
o Go > Connect to Server...
o Enter 10.0.1.1 for the server
o Enter Disk Password
o Connect
If this still doesn't solve the problem, let's double-check your disk sharing settings...
AirPort Extreme Base Station (AEBSn) - File Sharing Setup
Either connect to the AEBSn's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Mode, check these settings:
Disks - File Sharing
o Secure Shared Disks: <With disk password | With base station password | With accounts >
(Note: Choose "With a disk password," or "With base station password" if you want to secure the shared disk with a password, or choose "With accounts" if you want to secure the disk using accounts.
If you choose to use accounts, click Configure Accounts, click the Add "+" button, and then enter a name and password for each user that will access the disk.)
o Guest Access: <Not allowed | Read only | Read and write>
o Share disks over Ethernet WAN port: (unchecked)
(Note: Select the "Share disks over Ethernet WAN port" checkbox if you want to provide remote access to the disk over the WAN port.)
o Advertise disks globally using Bonjour: (unchecked)
o Workgroup: <Windows workgroup name>
o WINS server: <WINS server IP address>

Configure TC and Airport Extreme Base Stations with different channels

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

How can I extend a wireless network with my AirPort Extreme Base Station?

Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
-MacUser

The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

How to add NAS to existing Airport Extreme Base Station Network...

Hi! I have a Airport Express network (DSL provided via a DSL modem) that is connected to the PC via ethernet, iMac 333 via Wireless adapter, and Powerbook via wireless card. I am bursting at the seams with components!!
I have the printer set up via the AE.
I would like to add a NAS to the works. (Just to see if it can frustrate me even more! )
How exactly would I hook this up? Any suggestions? Has anyone done this? Have a favorite NAS device you can recommend? We are looking to install this for a centralized place to store all our music, photos, movies, etc. We have TONS of digital media to store and it is clogging up our respective hard drives!
Thanks in advance for the help!!
Minder
Ti Powerbook 15 inch Mac OS X (10.4.6) iMac Grape 333MHz, Custom built PC and a Flower Power iMac soon coming home with me too...
Ti Powerbook 15 inch Mac OS X (10.4.6) iMac Grape 333MHz also

It is unclear... Do you have an AirPort Extreme base station (AEBS) or AirPort Express (AX)?
If you have an AEBS then you should have this configuration:
DSL modem<->[WAN] AEBS [LAN]<->PC
If that is your current setup, you would need to modify it by adding an Ethernet switch (or hub) so that it looks like this:
DSL modem<->[WAN] AEBS [LAN]<->switch<-+->PC
.......................................|->NAS

Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

Just spoke with Cisco about the router. They said the router is compatible with the E1500. They suggested that I contact Apple to see if their default IP address was that same as the router (192.168.1.1). They told me I would have to change it if that was the case. How would I do that?

How do I open the same ports on an Airport Extreme Base Station for multiple computers at the same time?

As the title suggests...
I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router.   I need many ports opened on the AEBS for all of the computers- not just one computer. (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router).   Port forwarding only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time.
How do I do that on an AEBS?
In the same way, I have a small office of four iMacs using an old airport with the same exact issue.   I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP.   I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP.    I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine.    How do I open the firewall for the other machines?
TL,DR version: How do you open ports on an Airport Extreme Base Station instead of forwarding ports?   Forwarding ports doesn't work for multiple IP's.

You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

HT4259 How do I set up an Airport Extreme Base Station (v. 7.6.1) to allow wireless network extension?

I have an Airport Extreme Base station (purchased in 2009) and an Airport Express base station (purchased in 2011 - the model that plugs directly into the electrical outlet) (both version 7.6.1 according to the Airport Utility info). I want to use the Airport Express to extend my wireless network. Using Airport utility setup I have a software option on the Airport Express to set it up to extend the network but I do not have an option on the Airport Extreme wireless setup screen that I can check to allow my wireless network to be extended.
All of the documentation I can find on Apple Support states that I should have an option I can check to allow the wireless network to be extended while in the wireles setup section for the Airport Extreme in Airport Utility; but, that check option isn't there. Is this a case of my Airport Extreme base station being too old to offer that option? Incidentally, when I try to select the extend wireless network option on the Airport Express from the Airport Utility wireless setup menu I get an error message (no details - just an error message). The same Airport Express sets up fine if I select join a network (not what I want to do). Am I just dealing with outdated equipment or does anyone have a suggestion? Thanks.

Close AirPort Utility if it is open.
Temporarily, move the Express to the same general area as your AirPort Extreme and power it up and wait a minute.
Hold in the reset button on the Express for 9-10 seconds and then release. Give the Express a full minute to restart to a slow, blinking amber light.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear
Click on AirPort Express just below that and AirPort Utility will automatically open
Wait a minute while AirPort Utility analyzes the network and announces that the Express will be configured to "Extend" the AirPort Extreme network.
Enter a device name for the AirPort Express and click Next
Wait another minute to allow the configuration to occur.
When you see the Setup Complete message, click Done.
Now move the Express to a location that is approximately half the distance from the AirPort Extreme and the general area that needs more wireless coverage
Power up the Express and you are all set. Trash those old instructions.

How do I connect my Synology NAS to my AirPort Extreme base station?

I'm considering replacing an Apple AirPort Extreme base station with my current 5 year old router. I would appreciate if someone could tell me how the AirPort Extreme differs from any regular router. I do not have any OS X devices, but I have a lot of iOS devices. If my understanding is correct, I can set up the AirPort from an iOS device.
Also, I need to know how I would connect my Synology NAS system to the AirPort Extreme network via an Ethernet cable. I would need to be able to acces the files on the NAS through Windows clients. My Synology NAS currently has a web interface....would I still be able to access that web interface with the AirPort?
Thanks for all your help in advance as I am VERY new with networking devices.

I would appreciate if someone could tell me how the AirPort Extreme differs from any regular router.
The AirPort Extreme is a combination router, wireless access point, and Ethernet switch. It also provides both external USB hard drive and printer sharing. So, it is not much different than most other routers on the market today. The one main difference is how you administer it. Unlike most other routers that employ a web-based administration interface, the AirPorts use a dedicated utility, called the AirPort Utility.
I do not have any OS X devices, but I have a lot of iOS devices. If my understanding is correct, I can set up the AirPort from an iOS device.
Yes. There are versions of the AirPort Utility for OS X, Windows, or iOS devices.
Also, I need to know how I would connect my Synology NAS system to the AirPort Extreme network via an Ethernet cable. I would need to be able to acces the files on the NAS through Windows clients. My Synology NAS currently has a web interface....would I still be able to access that web interface with the AirPort?
Your Synology NAS would connect to the AirPort Extreme pretty much the same as for any other manufacturer's routers. That is, you would connect it to one of the available LAN (opposing arrows) ports on the Extreme. You would still use the same web-based interface as before.
Note: When connected to an Ethernet port, the NAS would still function as usual. The AirPort Extreme would not provide any file sharing functionality when connected in this manner. All file sharing features would be the responsibility of the NAS device.

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

Once you have the drive connected to your Mac, click System Preferences (gear icon) on the dock
Click Time Machine
Click Options
Be default, the hard drive will be Excluded from backups. Click the drive to highlight it, then click the "-" (minus) button at the bottom of the list to remove the drive from Excluded items.
The drive will be backed up on the next Time Machine pass
Everything above assumes that the hard drive has been formatted in Mac OS Extended (Journaled) as Time Machine will only backup drives in that format.

How to get this Airport Extreme base station to produce a wireless network?

I had this Airport Extreme base station working fine at the house that I moved from a couple of days ago.
After my house move, however, it seems that the AE base station isn't producing a wireless network. My wireless laptop isn't detecting a wireless network. Also, the left hand side light on the AE base station is not lit.
The AE base station was softly cushioned during house the move.
Regarding configuration:
My non-wireless iMac (running 10.3.9) connects to the AE base station via an ethernet cable.
Before my house-move, I regularly connected wirelessly via the AE base station from a couple of wireless-equipped laptop computers.
I was using AE software version 5.6. (In desperation, I have just updated to version 5.7 - but that hasn't improved or changed situation.)
At the new house, I found that I had to reset the AE base station back to factory settings before I could successfully connect to the internet through the AE base station from the (non-wireless) iMac.
Since resetting the AE base station at the new house, I can also print via a USB printer that's plugged into the AE base station.
I just cannot pick up any sign of a wireless network from the AE base station.
G4 Powerbook Mac OS X (10.3.9) Problem started while I had Airport Extreme software v5.6. No improvement/change after v5.7 update.

Sorry for my delay in closing this issue.
I got the wireless network running again - though I'm not sure which of a "litany" of separate actions (which I gleaned from dialogs in several similar postings for similar issues to mine) was the solution. I suspect it was one of the following two actions, which have stuck in memory:
1) I relocated a nearby cordless phone cradle/charger/base-station from alongside the Airport Extreme base station to about seven feet (two meters) away. However, the cordless phone is about eight years old, and I believe its radio frequency is far out of the range that I have read (in similar postings) can interfere with the Airport Extreme base station.
2) I re-set the Airport Extreme base station, (a) by depressing the tiny reset button at the rear of the base station for more than 5 seconds (until the led started blinking), (b) from Utilities/AirPort Admin Utility/Configure/Restart. However, I had reset the Airport Extreme base station those ways previously without that restoring the wireless network. Also, I didn't record the sequence of the multiple resets and the configurations at the times of the resets.

How configure Airport Extreme Base Station M8440

Similar Messages

Maybe you are looking for