How do I arrange for the Premiere output to be as near the same as the input as possible?

A newbie question.
I am editing a ten minute video down to a 90 second clip, with an added jpeg and a watermark. The first (http://www.youtube.com/watch?v=YQ3UOlHY3GE) turned out fine in terms of HD and widescreen. The second (http://www.youtube.com/watch?v=wgin-kBcep8) has not – it’s all scrunched. They both started out as identical format [1920x1080, 14005kbps data rate, 14133kbps total bitrate, 50 frames/second) MP4 files; the good output format is a (1920x1080, 25920kbps data rate, 2630kbps total bitrate, 25 fps) “Movie Clip”, whereas the poor output is a (720x576, 28807kbps data rate, 30343kbps total bitrate, 25fps) “Video Clip”.
How do I arrange it for the Premiere output to be as near the same as the input as possible, so as to present in YouTube as HD and fully widescreen? My guess is that I am doing something stupid when I open the incoming file.

Stephen,
In your initial post, you state:
They both started out as identical format [1920x1080, 14005kbps data rate, 14133kbps total bitrate, 50 frames/second) MP4 files;
If that is correct, then you ARE starting out with full-HD material, and that should be a PAR = 1.0 (Square Pixels) and 16:9 Aspect Ratio. Outputting to 1920 x 1080, should yield 16:9 with Square Pixels, as well.
Now, one of your output tests WAS to SD, and you state:
the poor output is a (720x576, 28807kbps data rate, 30343kbps total bitrate, 25fps) “Video Clip”.
but there is no mention of that output file's PAR, so it could be 4:3, or 16:9. The down-rezzed Export file WILL not look as good as full HD output to full HD.
I think that that latter 720 x 576 confused Harm, or maybe I am the one, who is confused?
Good luck,
Hunt

Similar Messages

How can I arrange for the Enter key to just drop d...

How can I arrange for the Enter key to just drop down a line instead of posting the message?

In Skype go to Tools -> Options -> IM settings -> Show advanced options. In the section “Pressing Enter will” select the option: Insert line break.
Note that this option is only available with Skype version newer than 6.1. The currently latest Skype version is 6.3.0.107.

HOW TO ASSIGN F4_VALUE_HELP FOR A REPORT OUTPUT FIELD???

Hi Gurus,
Can you please help me out in assigning F4_VALUE_HELP for a report output field where it is taking value as the input parameter....... If possible please help me out with some sample code ....
Regards,
Santosh
Intelligroup

I don't think that you are get the F4 functionality by pressing F4, but maybe if you use a hotspot you could achieve it. Check this sample. When you click on a company code in the list, it fires the F4 help defined by the program.
report zrich_0001 .
tables: t001.
data: begin of it001 occurs 0,
      bukrs type t001-bukrs,
      butxt type t001-butxt,
      ort01 type t001-ort01,
      land1 type t001-land1,
      end of it001.
start-of-selection.
select bukrs butxt ort01 land1 into table it001 from t001.
loop at it001.
    format hotspot on.
    write:/ it001-bukrs.
    hide it001-bukrs.
    format hotspot off.
    write: it001-butxt.
endloop.
at line-selection.
call function 'F4IF_INT_TABLE_VALUE_REQUEST'
       exporting
            retfield    = 'BUKRS'
            dynprofield = 'BUKRS'
            dynpprog    = sy-cprog
            dynpnr      = sy-dynnr
            value_org   = 'S'
       tables
            value_tab   = it001.
Regards,
Rich Heilman

How can I do for ESA work with token RSA, I mean when I entry the login the authentication with RSA

Hi there,
How can I do for ESA work with token RSA, I mean when I entry the login, the authentication ask me the token with RSA, Is it possible???
Regards,

Hello Miguel,
RSA tokens are currently not supported for login, neither to the GUI/CLI or access to the spam quarantine. There is currently a feature request"Support SecurID via RADIUS" for the WSA, if you want you can open a ticket and have either add your company to that request, or have it extended for ESA as well.
Hope that helps,
Andreas

I want to create a new customized screen layout for responsive HTML5 output. I don't want to use the ones present in the gallery. What are the steps to do so?

I don't wish to use the ones already present in the gallery. They do not meet my requirements. Therefore, I want to create/design my own screen layout for the responsive HTML5 output. Please let me know the steps to do so. How to create a SLZ file, what is the code that I need to write. What are the components that I need to create to have a complete screen layout to be used in a responsive HTML5 output.

That would require inline formatting and I doubt that is an option.
If I am following you, the header area is full width of the screen so I cannot see how it can be broader, Perhaps you mean deeper? A screenshot might help here. The change would be made in the layout.css file.
That would be a change in the layout.css.
I suspect that too is controlled by the layout.css.
To make the changes you would have to go into the layout.css and modify that. As you will see, it is a very complex CSS and that is why I said creating you own layout is not easy. Hopefully when Willam is available again, he may be able to give you some more specific information.
I think Willam will confirm that if you cannot read the existing CSS to make those changes, then creating your own skin would be beyond your capabilities. Please do not take any offence there, I am simply emphasising how complex a task it is to create a skin from scratch. It's not one I would take on.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

How much is CC for teams until 31May2014 without having previous versions of any of the suit

No price on the Adobe site caters for people without previous versions of the CS suite. So how would they ever attract new customers?

Hi there
Details of all the available plans/pricing - https://creative.adobe.com/plans
Also on the membership plans page - Membership plans: Pricing | Adobe Creative Cloud
The regular price for Teams is A$69.99 per user per month.
Thanks
Bev

No preview or preview button appears when I try to print a web page, as it does for any other file. How can I arrange for preview?

n the dialog box that appears when I try to print any web page, there is neither a preview nor a preview button, (although there is a preview if I open the web item as a pdf file, but that takes an extra step. A preview appears when I print any other file on my computer (a Macbook). Is there a setup procedure that will give a preview when printing one or several web pages?

The Print button in the "3-bar" Firefox menu button drop-down list opens the Print Preview window.
You can click the Print button in the Print Preview window or use the Print item in the File menu (File > Print) or use the Ctrl+P shortcut to have access to the print selection item and other print setup options.
* Tap the Alt key or press F10 to show the Menu bar.
* Use "View > Toolbars > [X] Menu Bar" to have the menu bar visible permanently.
*Universal Print: https://addons.mozilla.org/firefox/addon/universal-print/

How Do We Arrange For Armis To Be Available On MSN Games?

Armis is a high strategy board game that is currently played in over 130 countries online, it is primarily played at www.ArmisGame.com but also played
at various gaming sites like Kongregate.com, NewGrounds.com, etc ... we'd like to bring the game to the MSN Games community, who would we contact about that?

I'd get in touch with them over here.
http://zone.msn.com/en/general/microsite/community?intgid=hp_Nav_5
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

The Audio Output Signal is very weak and distorted. The Buil-In Speakers work ok. Whatcould be the problem???

Hello,
I spilled some liquid on my desk close to the Laptop. I proceeded immidiately to remove the MacBook Pro from the spillage site and dried the outside. The MacBook was not in use at the time and the lid was closed. Two hours later my wife used the computer and initially it functioned alright, however, after about 20 minutes it all of a sudden died and could not be re-started. Later that evening I tried a few more times to re-start and was partially sucessful for a few seconds at the time. The next day I opened the Back Cover and noticed the dried residue of the spillage on the battery cover as well as on the motherboard.
I proceeded very cautiously to remove the stains and followed up with a hairdryer to remove any possible residue of moisture.
After that, the MacBook Pro funtioned normally again, with the exception that the analogue audio output no longer supports an earphone, or any outside audio amplifier or TV set. I must add that there is some presence of audio when I increase the volume setting to high, but the bass sounds are very distorted.
My question is, do I have to exchange the "Motherboard" in order to resolve this problem?
I would very much appreciate any suggestions you may have!
Regards,
Hank

Take it back to whoever "fixed" it. Apple won't touch it now.

For the ipod nano replacement program, can I just bring the iPod into an Apple store near me and do the exchange there?

Just wondering if this is a possibility, because I think it'd be easier that way.

Call the apple tech support line printed in your manual. They may be able to walk you through some troubleshooting. If they can't fix the problem, they can book you an appointment at your apple store. I just went through this yesterday.

Why the name of our source file should be same as the 'public class' name

Hi all,
I am very new in java and have a question in my mind.
I read somewhere , our souce file name should be same as public class in that file.
but i don't know the reason for this.
Can anybody help me out with this .
Thanks,

HMRPanchal wrote:
Thanks,
Can you give me some link or documents from where I can go through this article.
because I am not clear with what you are saying( makefiles , automatic recompilation etc).
I am a new in Java .The fact that you don't have to worry about those things is what makes it A Good Thing.

When starting my MAC on the home page with my icons-- how do I arrange icons alphabetically left to right

How does one arrange icons from left to right ala Windows. I would like the Mac disk icon in the upper left of the window followed by app and file icons to appear in alphabetical order from left to right. I know it will go vertically and then to the next row. I have been reading English like this for over 60 yrs and the default set-up gives an old man a large pain in the head. Any help would be greatly appreciated.
Thank you,
Jim Buckley

I think they do it to be a pain in the ***. There is no reason to have people read in reverse alpha order. Some countries read right to left but here it's reversed. You think the geniuses here would figure out how to make allowance for that in their software.
I love the mac mini's size, etc, but using mac in general has made me nuts. I don't understand how people think it's intuitive. I find myself taking a ridiculous amount of steps to get anything done, but it may just be me. I know some people just love them.

How do I use pan and zoom on vertical photographs without editing out most of the photo?

I am trying to make a slide show. When I have a vertically oriented (portrait) photograph and try to use pan and zoom, the feature eliminates much of the photograph. It seems the pan and zoom feature only works for horizontally oriented (or landscape) photographs. Is there a way to use pan and zoom on vertically oriented photographs to capture all or most of the photograph and zoom in from there?

gtavetian
I decided to use a different strategy to convey the principle. It is most likely that your photos will be 4:3 and you may or may not be taking them into a SD widescreen or HD widescreen project. With all those variables, to get the basic ideas across, I am going to use two models with a generalized scheme.
For this post....
NTSC DV Standard Project - Portrait Oriented JPG, in this case 2448 x 3264 3:4. Could be any Portrait Oriented JPEG any pixel dimensions. But best plan ahead for what you have and what you would like.
Manually set the project preset to NTSC DV Standard.
File Menu/New/Project and, in the new project dialog, set for NTSC DV Standard.
Before exiting the final dialog in that area, put a check mark next to "Force Selected Project Setting on This Project". Close out of there.
Next go to the Edit Menu/Preferences/General and remove the check mark next to "Default Scale to Frame Size". Close out of the preferences.
In the opened Premiere Elements Expert workspace, use Add Media/Files and Folders/Project Assets to get your portrait oriented JPG to the beginning of the Timeline.The 2448 x 3264 3:4 will overwhelm the space in the Edit Mode monitor. That is to be expected. The Timeline Indicator is at the beginning of the Timeline @ 00;00;00;00.
a. Click on the Timeline jpg to select it. With Motion Panel/Scale property (with Constrain Proportions with check mark), you want to scale the image so that the whole is shown within the mode space. You want to see the image's bounding box. See the next screenshot. The bounding box is the white outline around the image. It has handles.
After the scaling to get that look, the important information that you want is on the right in the Motion Panel
Position values 360.0 and 240.0
Scale value 14.6%.
The next phase is as before (See post 21 of this thread...but much of that is repeated below and modified for what is being described at this moment)
With Timeline Indicator at the beginning of Video Track 1 (00;00;00;00), go to Tools Menu/Pan and Zoom and click on it to open the Pan and Zoom workspace.
In the Pan and Zoom workspace, you will see that the feature has created the initial two Focus Frames for you.
Do not do anything to Focus Frame 1 in the bin below the image window.
Click on Focus Frame 2 in the bin below the image window and set the Focus Frame as wanted.
Click on New Frame in the panel to the left of the image window to create a third Focus Frame which will appear in the bin. Set Focus Frame as wanted.
Click on New Frame in the panel to the left of the image window to create a fourth Focus Frame which will appear in the bin. Set the Focus Frame as wanted.
Click Done to the Pan and Zoom workspace so that you are back in the Premiere Elements Expert workspace with its Timeline.
In the Expert workspace,
Move the Timeline Indicator to the last frame of the selected pan and zoom clip 1. In Applied Effects Tab/Applied Effects Palette/Motion Panel expanded, (Toggle Animation should be active at this point), make sure Position settings are 360.0 and 240.0 and Scale = 14.6% (with Constrain Proportions used).Then go to Tools Menu/Freeze Frame and set the freeze frame for 3 seconds and hit Insert in Movie.
Then move the Timeline Indicator to the first frame of the selected pan and zoom clip 1. In Applied Effects Tab/Applied Effects Palette/Motion Panel expanded (Toggle Animation should be active at this point), make sure Position settings are 360.0 and 240.0 and Scale = 14.6% (with Constrain Proportions used). Then go to Tools Menu/Freeze Frame and set the freeze frame for 3 seconds and hit Insert in Movie.
Render.
The Timeline content sequence from start to finish should be:
Freeze Frame 3 seconds First Frame of pan and zoom clip 1
Pan and zoom clip 1
Freeze Frame 3 seconds Last Frame of pan and zoom clip 1
Freeze Frame 3 seconds First Frame of pan and zoom clip 2
Pan and zoom clip 2
Freeze Frame 3 seconds Last Frame of pan and zoom clip 2
A Dissolve/Cross Dissolve Video Transition (1.00 seconds) is placed between end of Freeze Frame Last Frame of pan and zoom clip 1 and beginning of Freeze Frame 3 First Frame of pan and zoom clip 2.
Additional pan and zoom portrait oriented jpgs to the Timeline would be treated as above.
What was done above can be applied to any photo with any project preset. The basic idea is to
a. Start with determing the whole picture Position and Scale values as described with the Default Scale to Frame Size option disabled.
b. Do pan and zoom with Pan and Zoom Tool in its workspace
c. Return to Premiere Elements workspace to apply your Position and Scale values to the last frame of pan and zoom clip so that the last frame presents in full clip view. Then go to the first frame of the pan and zoom clip, and apply the Position and Scale values to it so that the first frame presents in full clip view.
d. If you want the whole view to present for more than that one frame, do the freeze frame at each end, with the wanted duration.
e. Apply emblessments as wanted, such as video transitions, an animated graphic flying through the last scene, etc.
We could take this same clip into a NTSC AVCHD Full HD 1080p30 project and do the same, except the Position and Scale values and the Scale % determined at the beginning and used subsequently will be different than in the NTSC DV Standard project.
Please check out the above and see how you do with it. If problems, please indicate where and we will work through them.
Thanks.
ATR

How to use webcam for Yahoo Messenger on MacBook Pro, How to use webcam for Yahoo Messenger on MacBook Pro

How to use webcam for Yahoo Messenger on MacBook Pro, How to use webcam for Yahoo Messenger on MacBook Pro because it's not working =(

The cheap & easy way is to just drag the app to the Trash.
If you want to get all of the associated files use an app deleting app like the free AppCleaner;
http://www.freemacsoft.net/appcleaner/
Just drag an app and drop it on the AppCleaner icon in the Dock and it will find and present to you all the files it thinks are associated with the app. You can uncheck any that you want to keep and then let AppCleaner Trash the rest.

How do I compensate for display objects jumping when screen scaling

I am building an application that is to run at 2 difference stage sizes. 960x640 and 1024x768 (for those paying attention, you may note that those are the high res settings for the iPhone and iPad2)
The app was designed and build to run on a stage of 960x640 and when running at this size, there are no problems.
When the app loads in the 1024x768 window, it "strechs" the stage to fill the window, but keeps the aspect ratio. Everything looks good and the application runs without any problems expect for one thing.
Sometimes, display objects on the stage "jitter" when moving or animating. I have discovered that this is because the stage is "scaling" the x and y values, and is not pixel snapping the objects on the screen, even though the x and y values of the display object are indeed whole numbers.
A prime example of this is I have 2 bitmapData images. bmData_s and bmData_h.
bmData_s is 192x388 in size.
bmData_h is created from a copy of bmData_s with a glow filter stroke on it, resulting in a image that is 198x394 (6 pixels bigger due to a 3 pixel stroke)
I place it on the screen using the following code:
(Background is a bitmap object that is 960x480 and places at 0,0)
(ObjOffset is a point in my app data to position the object, it's a point set to 53,195)
MyObj.x = Background.x + ObjOffset.x + (bmData_s.width/2);
MyObj.y = Background.y + ObjOffset.y + (bmData_s.height/2);
now, when the mouse rolls over the object, I have an event listener to change MyObj.bitmapData to bmData_h
MyObj.bitmapData = bmData_h;
MyObj.x = Background.x + ObjOffset.x + Math.floor(bmData_h.width/2);
MyObj.y = Background.y + ObjOffset.y + Math.floor(bmData_h.height/2);
and back to the _s image on mouse out.
Now, when the app runs on the iPhone which is a 960x640 screen size, or on the PC which is using a window of similiar size, the image doesn't appear to move at all... the "stroke" appears and disappears exactly as it is suppose to
However, when I run it in a window that is 1024x768, the _h image appears to "jump" one pixel up.
I have encountered many other similiar things that only occure when the stage is scaled. There is a spot in the app where I am animating a bitmap by manipulating it's scrollrect x and width (have it's do a wipe in from right to left like a peice of paper unrolling on a table) and due to the scaling, the right edge of the image jumps left and right 1 pixel... but on 960x640 screens, it looks perfect.
Does anyone know how I can compensate for this effect so that this jumping doesn't occur when the stage is stretched to fit the window it's running in?

Sounds like a x-browser rendering problem
my guess would be to scale down the inner div's so they add up to less than 100%.
If you floated div's and gave them a %, give one of the div's a smaller.
ie: 2 divs floated in a Header, give one 50% and the other 49.5%

How do I arrange for the Premiere output to be as near the same as the input as possible?

Similar Messages

Maybe you are looking for