How do I "Authenticate" an HP F4180 printer. It asks for a password. Macbook is asking for this.

I have a new MacBook Air on my home network with a hardwired HPF4180 all in one connected to a HP Computer.  The network recognizes the printer but it wants a name and password. to authenticate the printer.  It has never asked for a password before on any computer or network.  The Dell laptop recognizes the printer in the control panel settings.  I have downloaded the drivers for the 4180 to the Macbook Air.  It says the printer is ready, then requires the name and passord.

same to me only with hp laserjet cp1025 nw. I put in my password but it doesn't work -.- It says" password not accepted". PLEASE HELP SOMEONE!!!!!

Similar Messages

  • In Numbers '09, version 2.3 (554), how to I get spreadsheet gridlines to print out? I have a Macbook Pro and use OSX 10.9.4 Mavericks.

    In Numbers '09, version 2.3 (554), how to I get spreadsheet gridlines to print out? I have a Macbook Pro and use OSX 10.9.4 Mavericks.

    HP,
    In Numbers '09, the only lines that print are Cell Borders. Apply borders and test by Printing to PDF.
    Jerry

  • HT201407 I have problem with My IPhone after updating I was asked to enter password etc then asked to agree the terms and conditions which I did but nothing happens it stays on this page can someone help how to complete the last stage of updating?

    I updated my I Phone4 with the latest version iOS7 after updating I was asked to enter I tune password etc and then was asked to accept the terms and conditions which I did......but nothing happens it stays on the same unable to complete the final stage.....my phone does not work I am stuffed can someone help.....cannot get thru to Apple I tried contacting them

    Hi Rajvidya Das,
    Do the following, then try again:
    1.     Close all open apps: Double click on the Home key and then swipe up on each of the thumbnails that appear above the open app icons
    2.     Sign out of the iTunes store: Settings>iTunes & App Store, click on your Apple/iTunes ID, then sign out
    3.     Check Settings>Safari, and make sure that "Block Cookies" is not set to "Always". If it is, change it to either of the other two options
    4.     Make sure you do not have Restrictions turned on. If they are turned on, make sure that access is allowed for Safari, iTunes Store, Installing Apps, and Deleting Apps
    5.     Reset your device (nothing will be lost): Hold down the Home and Power buttons at the same time and continue to hold them down until the Silver Apple appears (up to 30 seconds). Once the Home screen redisplays sign back into iTunes and try again
    Cheers,
    GB

  • When I try to connect to wi-fi, it asks for the password, but I got this question.  If you don't know the password, check with the Wi-Fi network administrator, but I don't know how.

    Hi All, 
    When I try to connect to wi-fi, it asks for a password.  Then I got this question.  If you don't know the password, check with the Wi-Fi network administrator, but how do I find the network administrator.

    Whomever provides the wi-fi.
    To what wi-fi network are trying to connect?

  • How do i get an alignment sheet for a hp deskjet f4180 printer? cannot find mine.

    Need Alignment sheet for HP deskjet F4180.
    Help.

    Hi - Go ahead and follow the steps in this document to print the alignment page and run through the alignment process.  Make sure you follow the entire process as stated in the document.  If you don't finish the step to scan the alignment page, the printer will continue to print alignment pages.
    Hope that helps
    Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
    I am an HP employee.

  • SEVERE: SAAJ0009:  How do I stop stack trace being printed to standard out

    Anyone know why the following stack trace is printed when connection.call(message, endpoint); throws an exception? It happens when the server or web service is offline
    using jdb I can see that the next statement to execute is the return("FAIL .... but the stack trace is already printed by then. How do I tell it not to print the stack trace. I've tried adding a catch for java.io.IOException but the compiler says it's not thrown. Any ideas
    SOAPMessage response = null;
    try{
    response = connection.call(message, endpoint); <= blows up here "myClient.auth myClient.java:333)
    connection.close();
    catch (SOAPException ex){
    return("FAIL Error sending authentication soap message " + ex.getMessage());
    java.io.IOException
    at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLConnection.java:593)
    at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:272)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.post(HttpSOAPConnection.java:29)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection$PriviledgedPost.run(HttpSOAPCon
    ection.java:151)
    at java.security.AccessController.doPrivileged(Native Method)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.call(HttpSOAPConnection.java:12)
    at myClient.auth(myClient.java:333)
    at myClient.send(myClient.java:93)
    at myClient.main(myClient.java:550)
    Caused by: java.net.ProtocolException: Server redirected too many times (20)
    at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLConnection.java:800)
    at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:272)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.post(HttpSOAPConnection.java:27)
    ... 6 more
    May 18, 2004 12:23:05 PM com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection post
    SEVERE: SAAJ0009: Message send failed
    java.security.PrivilegedActionException: com.sun.xml.messaging.saaj.SOAPExceptionImpl: Message send
    failed
    at java.security.AccessController.doPrivileged(Native Method)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.call(HttpSOAPConnection.java:12)
    at myClient.authenticate(myClient.java:333)
    at myClient.send(myClient.java:93)
    at myClient.main(myClient.java:550)
    Caused by: com.sun.xml.messaging.saaj.SOAPExceptionImpl: Message send failed
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.post(HttpSOAPConnection.java:30)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection$PriviledgedPost.run(HttpSOAPConection.java:151)
    ... 5 more
    Caused by: java.io.IOException
    at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLConnection.java:593)
    at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:272)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.post(HttpSOAPConnection.java:29)
    ... 6 more
    Caused by: java.net.ProtocolException: Server redirected too many times (20)
    at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLConnection.java:800)
    at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:272)
    at com.sun.xml.messaging.saaj.client.p2p.HttpSOAPConnection.post(HttpSOAPConnection.java:27)
    ... 6 more

    For anyone who's interested, apparently I'm not the only one with this problem, others have asked the developrs to remove printStackTrace() from the SAAJ code. For now we have to redirect standard error or ignore

  • How can I reinstall my Deskjet F4180 if I do not have the install disk

    How can I reinstall my Deskjet F4180 if I do not have the install disk

    Jerry, welcome to the forum. Since you didn't mention which OS you are using, I provided the Software and drivers page for Win 8.1.  It provides the HP Deskjet F2100/F4100 All-in-One Printer series Full Feature Software and Driver.  This will install the printer.  If the OS is not correct, you can provide the correct one. Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.

  • How do I uinstall Yosemite? It's not compatible with my older MacBook Pro, and I can't connect to my printer or use safari

    How do I uninstall Yosemite? It's not compatible with my older MacBook Pro and I can't connect to my printer or access Safari

    How to Downgrade OS X Yosemite Back to OS X Mavericks

  • How do i set up my e print to print in color

    How do I set up my printer to print in color   ?

    Hi,
    On my printer, I set it to print in color then it will print in color. You can do the same for your printer. Millions of them are out there, what is yours anyway ? To help us answer question quicker, please read this:
       http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to/Welcome-Get-started-here/td-p/699035
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How to connect my cannon mx470 series printer with bluetooth to my mini mac?

    how to connect my cannon mx470 series printer with Bluetooth to my mini mac

    Does the printer actually support BlueTooth? If the printer is wireless, then most likely it uses Wi-Fi. Did you read the user guide that came with it? Or contact Canon tech support at their website.

  • How to Connect a USB-to-Wireless printer to a Wireless Network without a PC

    Some printers from HP do not have a Wireless Setup Wizard built into the front panel for connecting to a network.  These models install to a computer through a USB connection and the software then sends the wireless information across the USB cable to the printer.  However, you may not always have a computer present and still need to connect these printers to a wireless network.  You can use a wireless device, such as an iPad, to do this.  For the example below I have used an iPad and a Deskjet 3510 series printer.
    The first step is to make sure your printer is broadcasting a network (Ad-Hoc).  To do this, turn the printer on and press the wireless button or turn wireless off, then on in the Setup menu. Connect the iPad (or other wireless device) to the wireless signal being broadcast by the printer.
    Once the iPad is connected to the printer as a network connection, open the Web Browser on the iPad.  Type 192.168.223.1 in the address bar and go to that site.  The printer's status page should load and look similar to the image below.
    Click on the Network tab at the top of the Status page.  You may get a prompt warning about being redirected to an HTTPS site.  Click Ok on the message box to continue.  When you click OK, you may get a warning regarding the certificate or server identity.  Select the option that lets you continue.  The wording will vary from browser to browser, but there should be an option to continue anyway.
    Network status page should now be loaded at this point.  Select Wireless Setup Wizard to start the wireless network setup and click Next.
     When next is selected, it should list the available wireless networks.  Select your network from this list and select next.  When the network is selected, it should be highlighted.
    Enter the network’s password, if any, and select next.
     A message should be received indicating the name and if security is enabled.  The message below that should indicate the settings were saved successfully.  If it says the settings were saved successfully with an error, the network setup is more than likely functioning.  Select Ok at the bottom.
    After selecting OK, select Status to verify the printer is connected successfully.  It may take a few minutes for the wireless light on the printer to stop flashing.  Once it is a solid blue, the printer should be on the network and functioning.
    Once this is completed, then you will be able to reconnect to your normal wireless signal (Wireless Router) for internet access.  Now both the iPad and printer are on the same Home Network.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.
    This question was solved.
    View Solution.

    Hope this helps.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • How to create authorization to access Query Print Layout?

    Hi again..
    i have 10 query print layout, and not every user can view this layout.
    I assume,
    report 1-3 only for user A,
    report 4-7 only for user B, and
    report 8-10 only for user C.
    How to create autorization for Query Print Layout?
    Thankyou for the help

    Dony,
    In order to createthe PL's of customize report (from Query Manager) you will have to go the Tools Tab of the Menu Bar in which you will have to click the Queries tab which will lead to a drop down menu which when clicked will lead to Quaery Print layout. You will have to choose your query based upon whether from the reports tab double click it to open the Query Print Layout Designer.
    Here again in the Menu Bar you will find the under the Tools the first tab is the PLD which when clicked you can do the same process as explined below
    When you go to the document ( Any Document ) in the tool bar you would find the 24th Icon to be the Print Layout Designer Tab when you click this it takes you to the layout designer window.... below there is tab named set as default when you click this the system would ask you 2 choices
    1. Set as default for all users
    2. Set as default for current user
    Which means that you will have to open each and every form?
    for each and every user and set them as default for the user.
    If you feel this answer is helpful then please do remember to reward points
    Regards,
    Nagesh.

  • How to: Print table on first page, use second page (back) for text only

    Hi, I am looking for a clear document on how to use pagination and the Odd and Even pages.
    We need to print a table over several pages, but only on Odd pages.
    On the back of each page we need to print "Terms and Conditions". Is that possible? Can it be done without scripting
    We are on ADOBE version 8.1
    In the file properties, double sided is switched on, and version set to 8.1 and higher.
    I created two Master pages, a FrontPage with ContentArea1and a BackPage with ContentArea2.
    FrontPage is used for uneven pages, BackPage is used for the even pages. The masterpages are printed correctly (alternating properly).
    Two pages were created for the content area's:
    ITEMS: contains item data (table with header and footer). Place is "On Odd Page". After "Goto page BackPage". And if the table needs to be paginated it goes to BackPage with overflow leader "Conditions".
    CONDITIONS: contains a textfield (Terms and Conditions). Place is "On Even Page". After "Goto page FrontPage". No overflow.
    What should happen is that on the front pages the item table is printed. If there are too many lines it should overflow to page number 3 then 5 etc. All the even pages should display the text.
    What actually happens is that the item table also gets printed in the content area for the Condition text...
    Also the "Conditions" are not printed on the last back page. But only once before it...
    Cheers,
    Edwin.

    Fixed it... After a lot of creating, deleting, playing around with pagination and the inevitable cursing...
    I have created 5 pages:
    1. FirstPage
         - Odd/Even: Odd (Front) Pages
         - Placement: First page (In page set)
    2. FrontPage (For Odd pages)
         - Odd/Even: Odd/Front Pages
         - Placement: Rest of Pages
    3. BackPage (For Even pages)
         - Odd/Even: Even (Back) Pages
         - Placement: Rest of Pages
    4. LastPage
         - Odd/Even: No Odd/Even Restrictions
         - Placement: Last page (In page set)
    5. DummyPage
         - Odd/Even: Blank pages
    The 'Terms and conditions' are located on the BackPage and LastPage (as a text).
    The table that is printed is (of course) located on a normal page (flowed subform).
    Pagination tab: Placement = Following previous, and After = "Continue filling parent". No overflow... Basically, it's all default.
    The table lines will now start on the first page and if there are more lines than can be printed on this page, it will continue in the next content area. That will be on the FrontPage.
    The trick is that each master page must have a content area (mandatory). Except for Blank pages, but these cannot be used... Blank pages would only be used once, after the first page.
    What I discovered is that you can drag a content area away from the Master page and attach it to a different master page.
    Logically, if there is no content area on a page, then data cannot be printed there. So, I created a Dummypage. On this page I dumped the content areas from the LastPage and the BackPage. As a result, content cannot be printed anymore on the back of pages. Only the standard text (a text field) is printed there. When the data from the table is overflowing, it will automatically overflow from the FirstPage to the next content area. Which is located on the FrontPages only.
    The DummyPage is NOT used anywhere.
    The result is that the records can only be printed on the content areas that exist on the First and Front pages. The back pages are now skipped.
    Duplex printing is now working correctly, and the text is printed on the back of all the pages.
    Cheers,
    Edwin.

  • How do I install a Adobe pdf printer?

    Upgrade from Acrobat Pro X to Pro XI destroyed my prior Adobe pdf printer. How do I reinstall the printer instance without reinstalling Acrobat XI?
    I found a reply for an earlier version of Acrobat, but I have no interest in installing the PDF printer into \Desktop or \Documents. Whatever it said to do didn't work and I've received no reply to my question posted on that old thread.
    So, how do I recreate the Adobe PDF printer, and, how do I do so while selecting where I want the .pdf files to be located?
    Thanks in advance for help

    What OS are you running? If it is a version of Windows, is it 32 or 64 bit? Are you using 11.0.0? Did you reboot after the install? If you did not reboot, then do that first. The next step is to run a repair and then do the updates (XI is currently at 11.0.03). Both the Repair and the Updates can be run from the Help menu.

  • How do I get a webpage to print in a larger font?

    When I increase the size of the font in internet options, it helps the printed page, but increases the size of the webpage so much it is way too large. How can I increase just the size of my printed page?

    Good news, my file is printing correctly.
    Even though I installed the printer driver update once without any resolution to the problem, I decided to reinstall it again without any immediate success.
    I have to admit I've tried so many things to find some what I was doing wrong and to be truthful things got kind of confusing. One thing seems pretty clear (as clear as things can be at this point) is that when I installed the updated drivers a second time things still weren't working.
    In looking into the matter deeper I went to the printer set up utility there I found 2 listings for my printer but one had some language about being generic post script. I chose that printer from the print dialogue box and that still didn't work. I decided I was going to delete all the printers except the one that I think was there when I began (I say I think because this was the first time I had ever been to this screen) and try another reinstall of the updated printer drivers. Before I did however I decided to run a test and that's when to my delight things printed beautifully.
    Thank you so much for your help. I'm glad things are working, but curious what combination of things made it so. I know I should just be satisfied that things at this point are well and not question why or if they will be so in the future. I guess if they're not there are always good people like you to help.
    I learned a very important life lesson here - the value of asking for help, not being afraid to seem stupid and not disturbed by having to persevere.
    Thank you again every one.

Maybe you are looking for